www.mess-regeltechnik.at
www.platon-direct.eu
• Flow
• Temperature
• Pressure
• Level
• Pumps
• Systems
• Service & Calibration
LICO +43 1 706 43 000
LICO Electronics GmbH
Klederinger Str. 31
A-2320 Kledering, Austria
[email protected] www.lico.at
Tel. +43 1 706 43 00
CONTENTS
Foreword
04
05
New Products in this Issue
06
Flow Overview
Quick Reference Guide to Flow Products
Ranges for Glass Tube and Float
08
10
11
VA Flowmeters
NGX/LGX Series Glass VA Flowmeter
NGX Series Glass VA Flowmeter
LGX Series Glass VA Flowmeter
NGX/LGX Series - Accesories
GU Safety Housed Glass VA Flowmeter
PG Plastic VA Flowmeter
PGU Safety Housed Plastic VA Flowmeter
DFM Plastic VA Flowmeter
NG/LG Series Glass VA Flowmeter
GR Miniature Plastic VA Flowmeter
SGUV Shunt Orifice Flowmeter
LPCB Fire Sprinkler Flowmeter
100mm Scale Glass Tube & Float
Anaesthetic Glass Tube & Float
GIR (Floscan) Infra-Red Flow Alarm
Spares & Accessories
GMT Series Metal Tube VA Flowmeter
GMT Flanged Series Flowmeter
GMT Threaded Series Flowmeter
GMT Series Transmitter/Alarm Options
Mains Interface Relay Module
Variable Orifice/Swing Vane
AP Purgemeter/GPI Digital Liquid Turbines
High Pressure Liquid/Compressed Air
EPW Oil & Water Flowmeter
12
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
32
33
34
35
36
37
38
39
Turbine Flowmeters
Stainless Steel Turbine & Pelton Wheel
Digital Indicators
40
41
Electromagnetic Flowmeters
Model 910 Electromagnetic Flowmeter
Mag X1 Electromagnetic Flowmeter
42
43
Ultrasonic Flowmeters
Model 220 Portable Ultrasonic Flowmeter
Field Mount Ultrasonic Flowmeters
Ultrasonic Flowmeter/Switch
44
45
46
Laminar Flowmeters
Laminar Water Flow Transmitter
Laminar Gas Flow Transmitter
48
49
Primary Flowmeters
In-line Pitot ‘Flo-bar’ Pipe Section
Insertion Pitot Tube
50
50
Totalising Flowmeters
Water Meter/Oil Meter
51
Flow Controllers
Pre-set Flow Controller
MN/FV Automatic Flow Controllers
Automatic Flow Controllers (B and LB Flostats)
Automatic Flow Controllers
52
53
54
55
Indicators
Paddle Wheel/Ball
Flap/Plain
56
57
Switches
Pre-Set Flow Switch
Adjustable Liquid Flow Switch
58
59
Flow
2
www.mess-regeltechnik.at
01
CONTENTS
Switches
Paddle (Liquid) Flow Switch
Explosion Proof Flow Switch
Adjustable Paddle Flow Switches
Air/Liquid Mini Flow Switches
Explosion Proof Adjustable Flow Switch
Level Switches (Plastic Float & Stainless Steel)
Vertical Stainless Steel & Pair Drop
60
61
62
63
64
65
66
Level
Capacitance Level Transmitter
Ultrasonic Level Transmitter
Level Control Electrodes
Pump Control or Level Alarm Module
67
68
69
69
Valves
Proportional Control Valves
FCV Fine Control Valves
Needle Valves
Solenoid Valves (2 Way/3 Way Direct Acting)
Solenoid Valves (Servo-Acting/Coupled Diaphragm)
70
71
72
73
74
Technical Data
VA Flowmeter Sizing Data (Liquids)
VA Flowmeter Sizing Data (Gases)
Unit Conversions & IP Table
75
76
77
Pressure
Pressure Overview
mV Transducer/OEM Transmitters
General Purpose Pressuure Transmitters
HPS Series Transmitter
Economic Industrial Transmitters
PMC Overview
PMC Miniature Pressure and Level Transmitters
PMC Electronic Transmitters
Electronic Pressure Switch - Switch 2000
UDS2 Indicating Switch/Pressure Switch
Pressure Gauges
Low DP Gauge (Gases)
DP Gauge with Alarm/Transmitter
DP Flow Transmitter
High Precision Pressure Regulator
Electronic I/P Converters
Pressure Reducing Valve
Water Pressure Regulator Non-Relieving
Water Pressure Regulator
Pressure Relief Valve
78
80
80
81
81
82
83
83
84
85
86
88
89
90
91
91
92
92
93
93
Temperature
Temperature Overview
MicroCal 20 Series/ Instrumentation
Thermal Imaging Camera
Infrared Thermometer
94
98
99
99
Calibration
Service & Calibration Overview
Capabilities
100
101
Pumps
Pumps Overview
Wanner Hydra-Cell Pumps
Series 2000 Utility Pumps/Yamada Pumps
102
103
103
Systems
Systems Overview
104
Contact us
RM&C Instrumentation
Terms and Conditions
106
107
108
☎
+43 1 706 43 000
3
NEW PRODUCTS IN THIS ISSUE
6
NGX/LGX Glass VA Flowmeters
LPCB Approved
Fire Sprinker
Flowmeters
Page 12
Page 25
GMT Low Pressure
Drop Metal VA
Flowmeters
MagX1
Electromagnetic
Flowmeters
Page 30
Page 43
Ultrasonic
Flowmeter/Switch
Automatic Flow
Controllers
Page 46
Page 54
Capacitance Level
Transmitters
Ultrasonic Level
Transmitter
Page 67
Page 68
www.mess-regeltechnik.at
NEW PRODUCTS IN THIS ISSUE
Sensit Pressure
Transmitters
PMC Pressure and
Level Transmitters
Page 81
Page 83
Electronic Pressure
Switch
Pressure Switch
Page 84
Page 85
Process Calibrator
Thermal Imaging
Camera
Page 98
Page 99
Can’t find what you’re looking for then
call our
Infrared Thermometer
TECHNICAL SALES TEAM
as we can supply tailor-made solutions
Page 99
☎
0043 1 706 43 000
7
FLOW OVERVIEW
FLOW
Platon
Specialist manufacturer with 50 years experience
Industry leader for all your flow requirements
FLOWBITS catalogue
Flow Measurement
leading manufacturer of glass
and metal VA flowmeters
Custom products or systems
Application sales engineers to discuss
your requirements
Flow Products
8
Wide variety of VA flowmeters
LPCB approved models for fire sprinkler systems
Control valves
Ultrasonic and mass flowmeters
Many other types, please enquire
www.mess-regeltechnik.at
FLOW OVERVIEW
Glass & Plastic VA Flowmeters
Metal VA Flowmeters
• New NGX and LGX series
• Gas flow up to 440 L/min
• Liquid flow up to 40 L/min
• Simple to install and maintain
• Customised scales
• Alarm option, ATEX approved
• Anaesthetic flowmeter range
• Safety housed versions
• Gas flow up to 1000 m /hr
• Liquid flow up to 100 m /hr
• Pipe sizes from 1/2" to 4" (15 to 100 mm)
• Configurable to customer specification
• Low pressure drop versions
• Simple to install, use and maintain
• Alarm and transmitter options
• ATEX intrinsically safe approval
• Flanged or screwed options
Shunt Orifice Flowmeters
Ultrasonics Flowmeters
sizes from 1 1/4" to 24"
• Pipe
(32 to 610 mm)
• Rugged well proven design
• Flanged or victaulic fittings
• For clean liquids and gases
approved models for
• LPCB
fire sprinklers
plates and carrier
• Orifice
assemblies available
• Remote indication versions
• New extended flow ranges
• Non-invasive flow measurement
• Dual mode
• 6mm to 6.5m (1/4" to 256") pipe sizes
• All commonly used pipe materials
• ATEX Certified Version
or
• Portable
fixed models
Automatic Control Valves
Electromagnetic Flowmeters
• Pipe sizes from 1/4" to 4" (6 to 100 mm)
• Maintains flow at selected rate
• Independent of pressure fluctuations
• Gases or liquids
• No power required
• Adjustable over wide range
• Fast response
• Highly accurate
moving parts in the flow
• No
profile
data is
• Configuration
backed up and can be
3
☎
FLOW
3
recovered
• Datalogging function
• Diagnostic facility
+43 1 706 43 000
9
QUICK REFERENCE GUIDE TO FLOW PRODUCTS
Flow Meters
Material Product
FLOWMETERS
Glass*
SS*
Plastic
Glass*
Plastic*
SS
Plastic
Brass
Plastic
Various
Br/SS*
Plastic
Glass*
Various
SS
Various
Various
FLGX
FAP
FGR
FNGX
FPG/FPGU
FFLM
FFT
FFLA†/
FFLW/FFLL
FEFW/FEFL
FGP
FGMT
FFVA
FSGU
FFL/FFM
FNT/FBNO
POA
POA
Type
Page
Air
Min
Max
Unit
Water
Min
Max
Unit
VA
VA
VA
VA
VA
Mass
Turbine
15
37
23
14
18-19
48-49
40
0.005
0.5
0.03
0.005
10
0.000005
n/a
25
25
100
150
440
1000
n/a
L/min
L/min
L/min
L/min
L/min
L/min
n/a
1
1
0.005
0.002
1
0.000005
0.1
40
60
0.3
4.4
40
10
100
L/hr
L/hr
L/min
L/min
L/min
L/min
L/min
VA
VA
Turbine
VA
VA
Shunt VA
VA
Turbine
Electro Mag
Ultrasonic
38
39
37
30-34
20-21
24
36
40
42-43
44-45
3.6
360
n/a
n/a
n/a
n/a
0.5
1000
0.7
1500
30
1500
On application
On application
n/a
n/a
On application
m /hr
n/a
n/a
m3/hr
m3/hr
m3/hr
0.2
1
1
0.02
0.015
2
0
0.01
0.1
0.01
100
150
190
25
50
100
270
60
10
25
L/min
L/min
L/min
m3/hr
m3/hr
m3/hr
m3/hr
m3/hr
m/s
m/s
3
n/a
Oil
Min
Max Unit
On application
On application
Other mediums
Gas Liquid
On application
Yes
Yes
No
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
0.2
100 L/min
1
150 L/min
On application
On application
On application
On application
On application
On application
On application
On application
No
No
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
On application
On application
* manufactured by RM&C
† calibrated at 7bar G, 20° C
Standard calibration for all products, unless specified by supplier or customer, is ATP - 1.013 bar A, 20° C
Flow Switches
Material Product
Type
Page
Gas/Air
Liquid/Water
Min
Max
Unit
Min
Max
Unit
SS*
FLF
Piston
58
n/a
n/a
n/a
0.5
3.5
L/min
Brass*
FLF
Piston
58
n/a
n/a
n/a
0.5
10
L/min
Brass/SS FFSV6
Vane
61
9
60
m3/hr
4
30
L/min
Brass/SS FV10/FV11¥
Vane
63
15
85
m3/hr
9
36
L/min
Brass/SS FMR
Piston
59
n/a
n/a
n/a
0.4
40
L/min
Brass/SS F593/F594
Vane
60
n/a
n/a
n/a
2.5
53
L/min
Plastic
FV8¥
Vane
62
55
286
m3/hr
34
170
L/min
Brass/SS FVK¥
Vane
62
n/a
n/a
n/a
1.1
173
m3/hr
Brass/SS FFSV4
Vane
64
29
16920 m3/hr
0.7
545
m3/hr
* manufactured by RM&C
¥ check if actuation/de-actuation switching
Flow Regulators/Controllers
Material Product
Type
Page
Air
Water
Other mediums
Min
Max
Unit
Min
Max
Unit
Gas
Diaphragm 53
0.005
100
L/min
0.002
3.5
L/min
Yes
Yes
Brass/SS* FFV
Diaphragm 53
0.08
2200
m3/hr
0.02
75
m3/hr
Yes
Yes
Brass/SS* FB
Diaphragm 54
n/a
n/a
n/a
4
100
m3/hr
No
Yes
Brass/SS* FLB
Diaphragm 54
n/a
n/a
n/a
2
240
m3/hr
No
Yes
* manufactured by RM&C
Standard calibration for all products, unless specified by supplier or customer is ATP - 1.013 bar A, 20° C
10
Liquid
Brass/SS* FMN
www.mess-regeltechnik.at
☎
-
0.6-4.6
-
1-16
-
10-180
20-270
E
-
2-25*
10-80*
-
-
-
20-280*
-
50-800*
0.2-1.5
-
0.2-3.0
0.4-4.4
C
FGTF 1AHD
FGTF 1AHS
FGTF 1ASS
FGTF 2CHD
FGTF2CDSP
FGTF 2BHD
FGTF 2BHS
FGTF 2AHD
+43 1 706 43 000
FGTF 2AHS
FGTF 2ASS
FGTF 3AHD
FGTF 3AHS
†FGTF 3ASS
B
30-150
10-100
6-50
-
2-25
1-12
1-10
0.6-5.0
0.2-3.4
0.2-2.0
-
0.1-1.2
60-600*
2-40
D
-
-
-
-
-
50-700
-
30-300
-
10-120
-
5-70
F
-
10-110
6-54
-
2-28
1-14
-
0.8-5.8
-
0.3-2.5
-
0.1-1.5
J
30-130
10-85
4-40
-
2-22
1-10
-
0.6-4
-
0.2-1.7
-
0.1-1
M
-
10-75
4-36
-
2-18
1-10
-
0.8-4
-
0.4-2
-
0.1-1.1
R
30-120
10-80
4-40
-
2-20
1-10
-
0.8-4.4
-
0.2-1.8
-
0.1-1
G
-
10-100
4-50
-
2-26
1-12
-
0.6-5
-
0.2-2
-
0.1-1.2
50-900* 60-560* 100-700* 50-700* 50-700*
K
-
20-180
10-90
-
2-48
2-22
-
1-8
-
0.3-3
-
0.1-1.8
0.1-1.1
•
•
†FGTF3ASS (for gases) not suitable to be used with the GIR Infra-Red flow alarm on page 28
Other gas and liquid scales and custom calibrations are available, consult our Technical Sales Team for details
UKAS or ISO 17025 Calibration available
10-90
2-46
-
-
-
-
20-120* 10-100* 10-100* 10-120* 10-100* 25-280* 10-150*
5-100*
5-90*
30-140*
N
-
20-270
10-120
-
4-60
2-28
-
0.5-9
-
0.2-3
-
0.1-1.8
50-800*
0.05-1
H
-
15-140
10-65
-
2-36
1-18
-
1-7
-
0.4-2.8
-
0.1-1.7
L
30-150
10-100
6-50
-
2-25
1-12
-
0.6-5
-
0.2-2
-
0.1-1.2
P
30-140
10-100
4-48
-
1-25
1-12
-
0.6-4.4
-
0.2-1.8
-
0.1-1.1
T
30-120
10-85
4-40
-
2-22
1-11
-
0.8-4.8
-
0.3-2.2
-
0.1-1.2
60-600* 40-600* 100-750*
FLOWMETERS
S
-
40-380
10-180
-
5-95
2-44
-
1-15
-
0.4-5
-
0.2-3.4
0.2-2
30-350* 20-200* 50-290* 30-250* 20-250* 30-360* 20-280* 50-600* 40-360* 20-250* 20-220* 40-300*
5-80*
Acetylene
10-150*
J
Argon
-
M
Butane
-
R
Carbon
Dioxide
5-100*
G
Carbon
Monoxide
20-250*
K
Cracked
Ammonia
F
3
2
1
Required
Frame Size
-
N
Helium
-
S
Hydrogen
-
H
Methane
FGTF 1BHD
L
Nitrogen
@ ATP L/min (*=cm3/min)
T
P
Oxygen
-
(*=cm3/min)
L/min L/Hr
(*=cm3/min)
L/min L/Hr
D
Propane
FGTF 1CHD
Tube
Code
B
Air
@ ATP
E
Water
@20ºC
C
Scale Code
Popular ranges for Glass Tube and Floats @ ATP (1.013 bar A, 20ºC)
RANGES FOR GLASS TUBE AND FLOAT
11
NGX/LGX SERIES GLASS VA FLOWMETER
NGX/LGX
FLOWMETERS
• Easy to use, high visibility scale
• Rear ‘blow out’ safety vent
• UV stabilised rigid safety cover
• Gas or liquid flow measurement
• Instantaneous response
• Accuracy up to ±1.25% FSD
• Air flow range 5mL/min to 150 L/min
• Glass tube removal without tools
• ATEX Infra-red alarm option
• Range of accessories
• UKAS calibration optional
• Available from stock
• Next day delivery
(subject to specification)
Data Sheet DS1115
Specification
ENGINEERED TO FIT
Standard or custom scaled glass tubes to suit process fluids and conditions
Range of process connections to fit pipework requirements
Brass or stainless steel end blocks with optional integral flow control valve
Supplied with studs for surface panel mounting
•
•
•
•
ACCURATE MEASUREMENT
Flow up the tapered tube lifts the float to an equilibrium position.
Flow rate is then measured against the flat top edge of the float.
FLOWMETER CHOICE
A complete VA flowmeter consists of a glass flow tube and float
scaled to the flow units required, and a frame to provide the end
block supports and to cover and protect the tube. The NGX Series
frames use flow tubes with nominally 100mm long scales,
whereas the smaller LGX frames use flow tubes with nominally
30mm scales.
To choose a complete flowmeter select the frame code required,
and separately specify the fluid flow range needed on the flow
tube scale.
NGX and LGX Series frames are designed to fit your process. The options available allow easy installation, usually
surface mounted on a vertical panel. Process connections and labelling can be customised to suit the application.
12
www.mess-regeltechnik.at
NGX/LGX SERIES GLASS VA FLOWMETER
Standard Frame Codes
NGX T B 3 1 2
Process Connections
1 = 1/4" BSPP
2 = 1/4" NPT
End Block Style
I – In-line connections
T – Rear facing connections
V – Built in needle valve with rear connections
O-ring Seals
1 = Nitrile
2 = Viton
End Block Material
B – Brass S – Stainless
Frame Size
Chosen to suit flow tube required
External Connections
Process Connections:
Standard 1/4" BSPP or 1/4" NPT, 20mm OD
Mounting Stud:
M5 threaded with nut to locate meter on
vertical panel
Safety Vent:
Allows rear discharge of process fluid in event
of glass tube breakage. Dia 20mm
Dims
NGX
LGX
W
X
Y
Z
30mm
121mm
184mm
210mm
30mm
65mm
108mm
134mm
FLOWMETERS
Typical Model:
Flowmeter Types
NGX – Standard size (100mm scale)
LGX – Reduced size (30mm scale)
Custom Build
OUT
C/L
X
Z
Y
IN
Construction of the NGX and LGX
series frames makes custom build or
special process connections easily
achievable, whether for rear facing
or mixed rear/in-line fittings.
Specific custom logos can be printed
on the glass tubes and polycarbonate
covers if required to suit the
application.
W
Specification - Frames
Backplate
End Blocks
Seals
Cover
Connections
Max. Temp
Max. Pressure
Valve Option
Mounting Stud
White polyester powder coated aluminium
Suffix B – Bright nickel plated brass; Suffix S – Stainless steel
Nitrile on brass units; Viton on stainless steel units; Alternative seals available
Clip on clear UV stabalised rigid polycarbonate (required to locate flow tube into end blocks)
Models available with in-line or rear facing process connections (See page 14/15)
100°C with viton seals, 80°C with nitrile seals
Recommended maximum operating in non-shock applications: 16 bar
Fine control valve option has needle valve fitted on flowmeter inlet
M5 studs 13mm long c/w nut
Specification - Flowtubes
Flowtube
Scale
Scale Length
Float
Accuracy
Calibration
Borosilicate glass, precision moulded in three diameters to suit flow range
Fused ceramic black ink
NGX Series – 100mm nominal
LGX Series – 30mm nominal
Precision machined float, rotates to give flow visualisation
Model HD: Hollow Dural, red anodised
Model HS: Hollow Stainless Steel
Model SS: Solid Stainless Steel
±1.25% FSD standard for NGX Series
(±2.5% for 1CHD/BHD models, ±3% for predicted scales) ±5% FSD for LGX Series
All tubes are flow tested. Standard scales are
for air & water, as listed. Custom scales to suit process fluid
☎
+43 1 706 43 000
13
NGX SERIES GLASS VA FLOWMETER
FLOWMETERS
NGXV - Integral Valve
14
NGXI/NGXT- Non-valved
Product Codes
Product Codes
Plated Brass
FNGXVB111
FNGXVB211
FNGXVB311
Plated Brass
FNGXIB111
FNGXIB211
FNGXIB311
FNGXTB111
FNGXTB211
FNGXTB311
Stainless Steel
FNGXVS121
FNGXVS221
FNGXVS321
Stainless Steel
FNGXIS121
FNGXIS221
FNGXIS321
FNGXTS121
FNGXTS221
FNGXTS321
Options (see page 16)
• Bench Stand
• GIR Alarm
• Relay Module
• UKAS Calibration Certificate
Options (see page 16)
• MN Flostat Valve
• GIR Alarm
• Relay Module
• UKAS Calibration Certificate
www.mess-regeltechnik.at
FLOWMETERS
LGX SERIES GLASS VA FLOWMETER
LGXV - Integral Valve
LGXI/LGXT - Non-valved
Product Codes
Product Codes
Plated Brass
FLGXVB111
FLGXVB211
Plated Brass
FLGXIB111
FLGXIB211
FLGXTB111
FLGXTB211
Stainless Steel
FLGXVS121
FLGXVS221
Stainless Steel
FLGXIS121
FLGXIS221
FLGXTS121
FLGXTS221
Options (see page 16)
• GIR Alarm
• Relay Module
• UKAS Calibration Certificate
Options (see page 16)
• MN Flostat Valve
• GIR Alarm
• Relay Module
• UKAS Calibration Certificate
☎
+43 1 706 43 000
15
NGX/LGX SERIES - ACCESSORIES
MN Flostat - Automatic Flow Controller
Fully automatic, no external power required. Maintains
constant flow regardless of line pressure fluctuation. See
page 53 for full specification and ordering information.
FLOWMETERS
Bench stand
Mounts to NGX series flowmeters and allows vertical
bench mounting. See page 29 for ordering information.
GIR Infra-red Alarm
• Intelligent sensor for high or low alarm
• Use two units for dual alarms
• ATEX approved
See page 28 for full specification and ordering
information.
Relay Module
DIN rail surface mount mains interface relay
module provides power for one or two GIR
alarm units.
See page 35 for full specification and ordering
information.
UKAS Calibration Certification available
16
www.mess-regeltechnik.at
GU SAFETY HOUSED GLASS VA FLOWMETER
FLOWMETERS
The GU construction provides a rigid protective
structure around the flow tube, to allow installation
in unsupported pipework or to provide extra
protection to operators on high pressure or corrosive
applications.
• Robust construction
• Instant flow rate visual indication
• Suitable for installation in
unsupported pipework
• Flow tube scaled for any gas and
most liquids
• Safety housed for operator protection
• Site interchangeable 100mm scale
length tubes
• Alarm option available (See page 28)
• Optional fine control valve
(inset shown)
Data Sheet DS1111
Specification
Connections
Housing
End Fittings
Seals
Window
Pressure
Relief Vent
Installation
Dimensions
3/8" BSPP Female in-line
Polyester coated die cast Aluminium
Nickel Plated Brass or Stainless Steel
Nitrile with Brass (80°C max); Viton with Stainless Steel (100°C max)
Solid perspex (Note - toughened glass window option)
25 bar max, non-shock
Rear facing pressure relief vent
Vertical with flow upwards - read top of float
210 x 73 x 60mm depth
Product Codes
• First choose tube from page 11 then choose frame size and connection
Model Description
Standard GU with Brass end blocks
Standard GU with Stainless Steel end blocks
Frame Size
Size 1
Size 2
Size 3
Size 1
Size 2
Size 3
Code
FGUB111
FGUB211
FGUB311
FGUS112
FGUS212
FGUS312
• For optional Fine Control Needle Valves (see page 71)
☎
+43 1 706 43 000
17
PG PLASTIC VA FLOWMETER
Variable area flowmeters for higher flowrates in
1/2" and 1” pipes, using plastic TPX tubes and
Stainless Steel or Dural floats. Open design for
good float visibility.
FLOWMETERS
• Large flow capacity for use on 1/2" and 1" lines
• High visibility
• Instantaneous operation
• Suitable for use on a wide range of liquids
and gases
• Special scale options
• Low pressure drop
Data Sheet DS1140
Specification
Tube
Scale
Float
Accuracy
Housing
Connections
O-Ring Seals
Temperature
Pressure Limit
Installation
Dimensions (mm)
TPX plastic
Black, moulded onto plastic tube
Duraluminium for gases, Stainless Steel for liquids
±5% FSD (Air and Water calibrations)
White Polyester coated Mild Steel
1/2" & 1" BSPP Female plated Brass or Stainless Steel
Nitrile with Brass, Viton with Stainless Steel
80°C max
10 bar at 20°C
Vertical with flow upwards - read top of float
1/2"= 219 x 48 x 48 1" = 250 x 67 x 67
Product Codes
Flow Rate (ATP)
L/min
Air
10 - 100
20 - 180
40 - 440
Connections BSP
Brass Connections
Stainless Connections
1/2"
1/2"
1"
FPGB1
FPGB2
FPGB3
FPGS1
FPGS2
FPGS3
Water
1 - 10
2 - 22
4 - 40
1/2"
1"
1"
FPGB4
FPGB5
FPGB6
FPGS4
FPGS5
FPGS6
•
18
Laminated scales are available for other fluids and process conditions. Please contact our Technical Sales Team for details.
www.platon-direct.eu
PGU SAFETY HOUSED PLASTIC VA FLOWMETER
Plastic tube flowmeters in rugged safety housings
suitable for unsupported installation in process
pipework. Perspex cover retains easy readability
while protecting the operator.
FLOWMETERS
• Large flow capacity for use on 1/2" and 1" lines
• High visibility
• Instantaneous operation
• Suitable for use on a wide range of liquids
and gases
• Glass tube or special scale options available
• Low pressure drop
Data Sheet DS1140
Specification
Tube
Scale
Float
Accuracy
Housing
Connections
O-Ring Seals
Temperature
Pressure
Exhaust Vent
Installation
Dimensions
TPX plastic. Borosilicate Glass available as an option
Black, moulded onto plastic tube
Duraluminium for gases, Stainless Steel for liquids
±5% FSD (Air and Water)
Polyester coated die-cast Aluminium with perspex window
1/2" & 1" BSPP plated Brass or Stainless Steel, optional flanged fittings
Nitrile rubber on Brass, Viton on Stainless Steel
80°C max
10 bar max at 20°C
Rear facing blowout vent
Vertical with flow upwards - read top of float
250 x 95 x 86mm depth
Product Codes
Flow Rate (ATP)
L/min
Air
10 - 100
20 - 180
40 - 440
Connections BSP
Brass Connections
Stainless Connections
1/2"
1/2"
1"
FPGUB1
FPGUB2
FPGUB3
FPGUS1
FPGUS2
FPGUS3
Water
1 - 10
2 - 22
4 - 40
1/2"
1"
1"
FPGUB4
FPGUB5
FPGUB6
FPGUS4
FPGUS5
FPGUS6
•
Laminated scales are available for other fluids and process conditions. Please contact our Technical Sales Team for details.
☎
+43 1 706 43 000
19
DFM PLASTIC VA FLOWMETER
FLOWMETERS
All plastic construction VA flowmeters providing excellent chemical resistance
and readability, supplied complete with end connections, either for solvent
welding to PVC pipe or threaded. Up to three bi-stable alarms can be fitted to
each unit, or if required a 4-20mA transmitter is available. Over the last ten years
many thousands of DFM units have been supplied to practically every industry
in the UK. All units are available on quick delivery from our extensive stock.
• 0.75 - 1500 m3/hr Air in 14
ranges each with 10:1 operating
span
• Choice of tube materials
depending upon operating
temperature and pressure up
to 100°C and 10 bar
• Positive pipe O-ring sealing
requires less torque when
installing
• Options of alarms or 4-20mA
transmitter available
• Standard or magnetic floats
(where alarms are required) of
identical mass, ensure that the
calibration is retained if the
floats are replaced
Please contact our
Technical Sales Team on
+43 664 100 6538
Also available with shorter tube lengths, alternative materials, smaller pipe
sizes and lower flow ranges. Please contact our Technical Sales Team for details.
Data Sheet DS1113
20
www.mess-regeltechnik.at
DFM PLASTIC VA FLOWMETER
Pipework
Valves
For liquids may be installed upsteam or downstream. For gases install valves
downstream only.
Special Scales
Computer calculated custom scales are available, incorporating all temperature,
pressure, density and viscosity variables.
FLOWMETERS
Mainly used for rigid PVC imperial pipe. Alternative screwed BSP female inserts
available. Other connections and materials are also available, please contact our
Technical Sales Team for more details.
Specification
Pipe Size
Process Connections
Tube Length
Overall Length
Wetted Materials
Accuracy
Pressure
Temperature
Standard Conditions
1, 11⁄4", 11⁄2", 2 and 21⁄2" NB
Solvent weld or BSP Female threads
350mm
400, 408, 418, 432 or 444mm (dependant upon pipe size)
Polyamide tube, PVC connectors, EPDM O-rings & PVDF internals
±1.2% of reading ±0.4% of full scale
10 bar max at 20°C (de-rate to 1 bar at 75°C)
75°C max
Air and water at 20°C and 1 bar A
Product Codes
Pipe
Size
1"
1"
1"
1"
11⁄4"
11⁄4"
11⁄2"
11⁄2"
2"
2"
2"
21⁄2"
21⁄2"
21⁄2"
Range
Air
(m3/hr)
0.7 - 5.5
1.0 - 10.0
2.5 - 20
4 - 34
5 - 50
8.5 - 76
8 - 70
10 - 90
14 - 125
22 - 190
35 - 300
50 - 500
80 - 720
400 - 1500
OPTIONS
Bi-stable Alarm
4-20mA Transmitter
Solvent
Weld
BSP
Threads
Pipe
Size
FFVA0000
FFVA0001
FFVA0002
FFVA0003
FFVA0004
FFVA0005
FFVA0006
FFVA0007
FFVA0008
FFVA0009
FFVA0010
FFVA0011
FFVA0012
FFVA0013
FFVA0014
FFVA0015
FFVA0016
FFVA0017
FFVA0018
FFVA0019
FFVA0020
FFVA0021
FFVA0022
FFVA0023
FFVA0024
FFVA0025
FFVA0026
FFVA0027
1"
1"
1"
1"
11⁄4"
11⁄4"
11⁄2"
11⁄2"
2"
2"
2”
21⁄2"
21⁄2"
21⁄2"
Range
Water
(L/hr)
15 - 150
30 - 300
60 - 600
100 - 1000
150 - 1500
250 - 2500
200 - 2000
300 - 3000
400 - 4000
600 - 6000
1000 - 10000
1500 - 15000
2500 - 25000
10000 - 50000
Solvent
Weld
BSP
Threads
FFVA0028
FFVA0029
FFVA0030
FFVA0031
FFVA0032
FFVA0033
FFVA0034
FFVA0035
FFVA0036
FFVA0037
FFVA0038
FFVA0039
FFVA0040
FFVA0041
FFVA0042
FFVA0043
FFVA0044
FFVA0045
FFVA0046
FFVA0047
FFVA0048
FFVA0049
FFVA0050
FFVA0051
FFVA0052
FFVA0053
FFVA0054
FFVA0055
FFVA0056
FFVA0057
• Custom scales can be produced for other liquids and gases, and fluids working at other temperatures and pressures.
☎
+43 1 706 43 000
21
NG/LG SERIES GLASS VA FLOWMETER
FLOWMETERS
Improved for 2007, the NG & LG Series are
low cost frames for the standard 100mm
scale or reduced 30mm scale glass tubes.
Ideal for panel mounting. Both series are
supplied with mounting studs. Models
available with in-line or rear-facing process
connections; the latter available with an
optional needle valve for flow control. Float
and scale visibility is improved through the
use of a clear polycarbonate cover set
against a white background.
• Easy to use
• Simple and reliable
• Gas or liquid flow measurement
• Operator confidence from float rotation
• Instantaneous response
• Air flow range 5 cm3/min to 150 L/min
• Typically 10:1 range
• Glass tube removal without tools
Data Sheet DS1112
Specification
Backplate
End Blocks
Seals
Safety Cover
Connections
Pressure Max
White polyester powder coated
aluminium
Brass or Stainless Steel
Nitrile with Brass end blocks Viton
with Stainless Steel end blocks
Moulded Polycarbonate
1/4" BSP Female, 1/4" NPT Female
optional
16 bar non-shock
Temperature Max
Needle Valve
Installation
Dimensions
Rear Connection
Nitrile seals: 80°C Viton seals: 100°C
Flow control valve fitted
to NGV model only. Other models can
use separate needle valve type FCV
Vertical with flow upwards - read
top of float
210 x 30 x 46.5mm depth (no valve)
184mm pitch
Product Codes
• First choose tube from page 9 then choose frame size and connection
Connections
Rear facing
Rear facing
Rear facing
Rear facing
In-Line
In-Line
Valve
No
No
Yes
Yes
No
No
Material
Brass
SS
Brass
SS
Brass
SS
Size 1
FNGTB111A
FNGTS121A
FNGVB111A
FNGVS121A
FNGIB111A
FNGIS121A
Size 2
FNGTB211A
FNGTS221A
FNGVB211A
FNGVS221A
FNGIB211A
FNGIS221A
Size 3
FNGTB311A
FNGTS321A
FNGVB311A
FNGVS321A
FNGIB311A
FNGIS321A
• For 1/4" NPT thread change last digit of code to 2 (eg FNGTB112A)
22
www.mess-regeltechnik.at
GR MINIATURE PLASTIC VA FLOWMETER
FLOWMETERS
Plastic moulded VA Flowmeters with 50mm
scale and rear facing connections. Suitable for
flush panel or surface mounting, with or
without flow control valve, for air or water
ranges. Special integral flow guides stabilise
the float throughout the range to keep it
from hunting or wandering in the bore. The
float is highly visible against a white
background. The direct reading scales eliminate
troublesome conversions. These low cost
flowmeters are ideal for general use.
• Low cost flow indication
• Air or water calibration
• Large 50mm scale
• Stainless Steel rear connections
• Adjustable set point indicator flag
available on request
• Flow control valve option
Data Sheet DS1132
Specification
Materials
Connections
Temperature
Pressure
Installation
Panel Cut Out
Polycarbonate flowtube. Stainless Steel connections. Neoprene/Buna N O-rings
1/8" NPT Female
55°C max
100psi max
Tube must be vertical with flow upwards - read centre line of float against scale
116 x 19mm mounting brackets supplied with meter
Product Codes
Air Ranges at ATP
30 - 240 cm3/min
100 - 1000 cm3/min
200 - 2500 cm 3/min
0.5 - 5 L/min
1 - 10 L/min
2 - 25 L/min
10 - 100 L/min
Standard Model
FGR11
FGR13
FGR14
FGR20
FGR21
FGR22
FGR25
Valved Model
FGRV11
FGRV13
FGRV14
FGRV20
FGRV21
FGRV22
FGRV25
Water Ranges at 20°C
5 - 50 cm3/min
20 - 300 cm3/min
FGR32
FGR34
FGRV32
FGRV34
☎
+43 1 706 43 000
23
SGUV SHUNT ORIFICE FLOWMETER
FLOWMETERS
Shunt Orifice Flowmeters
are direct reading flow
measurement systems for
clean liquids and gases in
pipes from 1 1⁄4" to 24" diameter.
By introducing a standard sharp edge
orifice plate between flanges in the line, a
proportion of the main flow is diverted around
the external pipework, through a locally mounted
specially calibrated VA flowmeter. The flow through this
shunt meter is linearly related to the line flow and is read
directly on a linear scale.
• Easy installation between pipe flanges
• Instantaneous reading
• No electrical power needed
• Different process fluids or flow ranges
• Isolation valves for tube
replacement and cleaning
• Meters for line sizes up to 24"
• All Stainless Steel option available
• Option of GIR infrared alarms
• SGUL uses flexible PVC piping to install
• Designed to suit flange fittings
indicator at up to 25 feet away
(ANSI, DIN, BS10)
Data Sheet DS1160
Specification
Material
Flanges
DP Produced
Thickness
Valves
Tube
Piping
Housing
O-Ring Seals
Limits
Stainless Steel plate mounted in Polyester coated steel carrier ring
Standard BS10 Table E
25" WG for air 100" WG for liquid flows (max)
Standard 25mm
Dual SS isolating valves fitted
Borosilicate Glass, 100mm scale
Copper with plated Brass connections
Polyester coated die-cast Aluminium with perspex window
Nitrile
25 bar max, 80°C max
Product Codes
Flow Range
Air Flows at ATP
30 - 150m3/hr
40 - 200m3/hr
80 - 400m3/hr
180 - 900m3/hr
5 - 25m3/min
24
Pipe Size
1 1/4"
1 1/2"
2"
3"
4"
Code
FSGUVB1A
FSGUVB2A
FSGUVB3A
FSGUVB5A
FSGUVB6A
Water Flows at 20°C
2 - 10m3/hr
3 - 15m3/hr
5 - 25m3/hr
10 - 50m3/hr
20 - 100m3/hr
Pipe Size
1 1/4"
1 1/2"
2"
3"
4"
www.mess-regeltechnik.at
Code
FSGUVB1B
FSGUVB2B
FSGUVB3B
FSGUVB5B
FSGUVB6B
LPCB FIRE SPRINKLER FLOWMETER
FLOWMETERS
The Shunt Gapmeter Model LPCB is approved
for regular monitoring and testing of sprinkler
systems by the LPCB (Loss Prevention Certification
Board) under their ‘Rules for Automatic Sprinkler
Installations’, in the UK, and by many equivalent
organisations in other countries.
Model LPCB provides a compact,
robust, direct reading flowmeter for
50mm-200mm pipelines and is suitable
for use in horizontal or vertical pipes.
• Approved and listed by LPCB
for automated sprinkler systems
• 150 - 12,500 dm3/min range
• Easy and quick installation
• Flanged or victaulic connections available
• Instantaneous reading
• Best in class flow ranges
• Isolation valves for tube replacement
Approved and listed by the Loss
Prevention Certification Board, and
equivalent overseas authorities
and cleaning
• Air bleed and drain valves
• Spare tube supplied
Data Sheet DS1162
Specification
Main Orifice Carrier
Bypass Flow Indicator
Connections
Housing
316 Stainless Steel flow
orifice mounted in
Polyester coated Carbon
Steel carrier
Nickel plated Copper
impulse pipe and Brass
connections
Models for clamping
between flanges or utilising
approved groove couplings
Polyester coated die-cast
Aluminium with perspex
window
Filter Unit
316 Stainless Steel element
inside TPX tube
12 bar max at 20°C
30 bar hydraulic
Borosilicate Glass 100mm scale
Stainless Steel
Nitrile
Read from top of float
Limits
Pressure Test
Tube
Float
O-Ring Seals
Instruction
Spacing requirement:
Flange model = 40mm for all sizes
Groove model = 90mm for 50, 80, 150mm sizes
Groove model = 100mm for 200mm size
Product Codes
Flow Range(dm3/min)
150 - 750
300 - 2300
500 - 3500
900 - 8200
2500 - 12500
Nominal Size (mm)*
50
80
100
150
200
Code (Flanged)
FLPCB - F1/5
FLPCB- F1/6
FLPCB - F1/7
FLPCB - F1/8
FLPCB - F1/9
Code (Grooved)
FLPCB - F1/10
FLPCB - F1/11
FLPCB - F1/12
FLPCB - F1/13
FLPCB - F1/14
* 50 -150mm to BS 1387, 200mm to BS3600
☎
+43 1 706 43 000
25
100mm SCALE GLASS TUBE & FLOAT
The Platon range of Glass Tube Flowmeters typically uses the 100mm
scale length borosilicate glass tube and a float. Based on the well known
variable area (VA) principle of flow measurement, these flowmeters
provide clear, simple and reliable operation.
FLOWMETERS
Principle of Operation
Fluid flowing vertically upwards through the tapered glass tube
causes the float to rise to an equilibrium position. Flow rate is
measured by reading the top edge of the float against the scaled tube
(see diagram below).
Platon Glass Tubes from RM&C are individually scaled and calibrated
according to customer’s requirements. Custom scales are produced
using our "Reynolds Curve" prediction software, which uses air or
water calibration data corrected for the effects of temperature and
pressure on the density and viscosity of the working fluid.
• Instantaneous response
• Simple and relaible operation
• Low line pressure loss
• High resolution
• Custom scales available on request
Specification
Scale Length
Overall Length
Flow Tube Material
Float Material
Accuracy: 1
Standard Conditions
Suitable Frames
Installation
100mm typically
140mm
Borosilicate Glass with fused ceramic scale
Duraluminium or Stainless Steel for gases; Stainless Steel for liquids
Air: ±1.25% FSD Gases: ±3% FSD Water: ±1.25% FSD
1.013 bar A & 20ºC (ATP)2
NG & G series & GU type
Vertical with flow upward - read top of float
Notes
1
FGTF 1CHD and FGTF 1BHD scales are specially calibrated for very low flow rates with an accuracy of ±2.5%FSD.
2
Atmospheric temperature and pressure is abbreviated to ATP on Platon flowmeters. Custom scales for other
conditions are available. Unless requested, custom scale units will be expressed at ATP.
Product Codes
For standard gas or water ranges, select the required flow range from the table
on page 11. To order, quote the Tube Code, with the Scale Code as a suffix. Unit
scaled tubes, 1 to 10 linear units, are also available as standard. Quote the
required Tube Code with the suffix A.
Example: For a typical Argon flow of 3 L/min, choose the range 0.6 to 4 L/min
and quote the code FGTF 2BHD-J.
26
Spare Glass Tube and Floats
Code
FGTF****-*
FGTF3ASS-* (for gases)
Custom scales are supplied at no extra cost
www.mess-regeltechnik.at
Platon Glass VA Flowmeter Tubes are widely
supplied for use on medical equipment such as
anaesthetic trolleys. Available in keyed lengths
and colour coded to avoid incorrect
installation, standard tubes are calibrated for
oxygen, nitrous oxide or air.
• Instantaneous response
• Reliable operation
• High visibility scale fused into flow tube
surface
• Float rotation gives operator confidence of
FLOWMETERS
ANAESTHETIC GLASS TUBE & FLOAT
correct performance
• Borosilicate glass tube, anti-static coated
to avoid static build up
• Flow ranges from 10:1 to 150:1 available
• Individual flow calibration
• Standard gases - air, oxygen, nitrous oxide
• Customised logo available
Data Sheet DS1170
Specification
Glass Tube
Float
Scale
Tube Diameter
Standard Lengths
Gases
Flow Ranges
Accuracy
Borosilicate Glass
Red Duraluminium
Fused ceramic black ink
O/D 12mm or 15mm nominal
230/240/250/260mm (150mm to special order)
Oxygen, Nitrous Oxide, Air, Helium, Carbon Dioxide, Cyclohexane
0.1 - 1.0 L/min
1.0 - 10 L/min
0.1 - 15 L/min
To specification required
Typical ±2% FSD, ±10% reading or ±2.5mm
How to Specify
•
•
Anaesthetic tubes are made to order
Contact our Technical Sales Team specifying the gas, flow range and tube length required for a specific product
and price quotation
☎
+43 1 706 43 000
27
GIR (FLOSCAN) INFRA-RED FLOW ALARM
FLOWMETERS
Floscan Flow Alarms use an infra-red beam across the
glass flowtube of a VA meter. Passage of the float
between the sensor arms is detected and logic within
the electronics determines whether the float is above
or below the sensor position. Clipped to the rear of the
frame, the sensor can be adjusted up and down to the
required position. The sensor is 12Vdc powered with a
transistor switch output to drive external logic circuits.
A mains operated power unit and slave relay can be
used to drive either one or two Floscan sensors.
• High or low flow alarm
• Intelligent: knows whether float is above or below
the sensor
• Adjustable over full range of flowtube
• DC output direct to standard logic circuits
• Optional Mains Interface Relay Module (see page 35)
• ATEX approved
Suitable for flowmeter housing:
•
•
•
Data Sheet DS1120
NGX/LGX Series (page 12-16)
GU to special order (page 17)
SGUV to special order (page 24)
Specification
Sensor Type
Direction Logic
Setting Position
Sensor Cable
Cable Functions
Voltage Supply
Temperature
IR Beam break detection
Position of float above/below
sensor established after first
detection of float after power up
Held by spring clip anywhere in
flow tube operating range
2 metre, 3 core screened
Red - Positive
Black - 0V Common
White - Transistor output
12V nominal, 8V - 26Vdc range at
25mA
-5 to 50°C
Environment
0utput
Switch Points
Dimensions
Approval
IP44 with cable exit downwards
Open collector transistor 50mA
30V max (sensor positioned open
circuit for low flow alarm, with
cable exit down) conducts for flow
above switch point
For falling float, top edge of float at
centre line of sensor. For rising
float, switching occurs when base
of float passes centre line.
H22 x W60 x D30, 4mm space
needed behind frame
ATEX EEx ia IIC T4
Product Codes
Description
Floscan sensor for liquid applications
Floscan sensor for gas applications
Mains Relay (see page 35)
Code
FGIR*L
FGIR*G
F58384
•
•
•
Specify tube size 1, 2 or 3 at * in model code. GIR is not
compatible with all old flowtubes. A new flowtube should be
purchased with the GIR alarm
May not be suitable for some liquid applications with gas
bubbles or solids in medium.
Not suitable for guided floats
Please contact our Technical Sales Team for details
28
www.mess-regeltechnik.at
SPARES & ACCESSORIES
Genuine Platon Spares & Accessories
FK23000
FK23036
FLOWMETERS
• A full range of accessories are available for your Glass Tube Flowmeters
• O-ring seals are available in Nitrile and Viton
FK23045
F54108
F5841303
F5841305
Product Codes
Platon Flowmeter
NGX/LGX
Accessory/Spare Part Description
Bench Mount Stand
NGX Valved Panel Mount Bezel
NGX Non-Valved Panel Mount Bezel
Brass Adaptor to fit 1/4" BSP FCV (Fine Control Valve)
Stainless Steel Adaptor to fit 1/4" BSP FCV (Fine Control Valve)
Connection Hose Adaptors (pair) Brass 1/4" NB Hose to 1/4" BSP
Stainless Steel 1/4" NB Hose to 1/4" BSP
Brass 1/4" NB Hose to 3/8" BSP
Stainless Steel 1/4" NB Hose to 3/8" BSP
Tube to insert O-rings (pack of 10)
Size 1 Nitrile
Size 1 Viton
Size 2 Nitrile
Size 2 Viton
Size 3 Nitrile
Size 3 Viton
Insert to end block O-rings (pack of 10)
Nitrile
Viton
Ordering Codes
F54108
FBEZELGTV
FBEZELGT
F5842112
F5842114
GU
Brass adaptor to fit 3/8" BSP FCV (Fine Control Valve)
Stainless Steel adaptor to fit 3/8" BSP FCV (Fine Control Valve)
F5842124
F5842122
PG/PGU
Tube to insert O-rings (pack of 10)
Size 4 Nitrile
Size 4 Viton
Size 5 Nitrile
Size 5 Viton
FK23107
FK23108
FK23109
FK23110
☎
+43 1 706 43 000
F5841303
F5841313
F5841305
F5841315
FK23004
FK23000
FK23007
FK23001
FK23026
FK23036
FK23059
FK23045
29
GMT SERIES METAL TUBE VA FLOWMETER
FLOWMETERS
Platon GMT Metal Tube Flowmeters are magnetically
coupled VA meters for liquids or gases. Fluid flow
lifts the float assembly (with its encapsulated
magnet) inside the tapered flow tube. The meters
external pointer follows the magnetic field indicating
flow against a clear 150° scale, typically displaying a
10:1 flow range.
Its robust construction with no
glands or seals makes the GMT
ideal for arduous service;
particularly
high
pressure
applications or extremes of
temperature.
It has particular advantages where opaque or staining
fluids would make glass tube flowmeters unsuitable.
Available in standard sizes from 1/2" - 4", with Brass or
Stainless Steel bodies.
Custom scales can be
produced to suit other
flows and conditions.
Alternative material options such
as Hastelloy,Monel and PTFE-lined
versions are available on request.
High and low flow alarm versions are also available
(see page 34). For full electronic transmission and
totalisation, utilising the vampire electronic
module (see also page 34).
Please contact our Technical Sales
Team to discuss your application
30
www.mess-regeltechnik.at
GMT SERIES METAL TUBE VA FLOWMETER
A permanent magnet encapsulated within the
stainless steel float drives the external
magnetically coupled pointer. Float movement
is related to flow rate, and the indicator scale is
marked in the correct units of flow for the
process conditions.
The standard unit requires no electrical power.
As the measuring element is a sharp edged
disc, the meter is relatively insensitive to
viscosity changes in the fluid and to pipe
bends in the external pipework. The only
moving part in the flow is the float which is
retained in place by float guides at either end
of the meter.
FLOWMETERS
Principle of operation
Specification
• Local mechanical installation
• No power required (local indicator)
• Clearly visible scale
• Scaled for process fluids
• Easy installation - flanged or screwed
• No glands or seals
• Robust, simple construction
• Pulsation damper on gas meter
Sectioned model GMTXA313G
Options
• Alternative flanged or threaded options available
• Special body and indicator materials
• Optional alarms and transmitters (see page 34)
• Hygienic versions with triclamp connections
Please contact our Technical Sales Team to discuss your application
☎
+43 1 706 43 000
31
GMT FLANGED SERIES FLOWMETER
GMT flanged metal tube magnetically coupled variable
area flowmeter. Robust construction for heavy duty.
Available in sizes 1/2" to 2" for gases, or 1/2" to 4" for
liquid flows.
FLOWMETERS
• Clearly visible scale
• Scaled for process media
• Easy installation - flanged
• No glands or seals
• Low pressure drop version available
with PVC floats on 1/2" and 1" models
• Other options available
Data Sheet DS1220
Specification
Body Materials
Float
Guides
Connections
Overall Length
Indicator Housing
Protection
Flow Range
Accuracy
Flow Scale
Pressure
Stainless Steel
Stainless Steel or PVC on low
pressure drop units
Stainless Steel
Flanges DIN PN16 as standard
250mm for 1/2" to 2" units
Aluminium, Polyester coated
IP65
10:1 typical
±2% FSD
100mm long, 150° typical
100 bar max or as flange rating
Temperature
Pulsation Damper
Standard Conditions
Installation
Approval
200°C max (50°C on low
pressure drop units)
On gas meters a dashpot
smoothes out flow pulsations
1.013 bar A & 20°C (ATP)1
Vertical with flow upward
CRN.CSA-OF4812.26
1
Atmospheric temperature and pressure is abbreviated to
ATP on Platon flowmeters. Custom scales for other
conditions are available. Unless requested, custom scale
units will be expressed at ATP.
Product Codes
1/2" or 15mm Pipe Size
GAS - m3/hr Air @ATP
0.5 - 5.0
FGMT111G
0.75 - 7.5 FGMT112G
1.2 - 12.0 FGMT113G
1.8 - 18.0 FGMT114G
1" or 25mm Pipe Size
GAS - m3/hr Air @ATP
3 - 30
FGMT211G
5 - 50
FGMT212G
10 - 75
FGMT213G
10 - 120
FGMT214G
20 - 200
FGMT215G
40 - 360
FGMT216G
2" or 50mm Pipe Size
GAS - m3/hr Air @ATP
18 to 180 FGMT311G
30 to 300 FGMT312G
60 to 600 FGMT313G
100 to 1000 FGMT314G
LIQUID - L/hr Water @20oC
20 - 160
FGMT111L
20 - 250
FGMT112L
40 - 400
FGMT113L
60 - 600
FGMT114L
LIQUID - m3/hr Water @20oC
0.1 - 1.0
FGMT211L
0.2 - 1.6
FGMT212L
0.2 - 2.5
FGMT213L
0.4 - 4.0
FGMT214L
0.6 - 6.0
FGMT215L
1.0 - 10.0 FGMT216L
LIQUID - m3/hr Water @20oC
0.6 - 6.0
FGMT311L
1.0 - 10.0 FGMT312L
2.0 - 16.0 FGMT313L
2.0 - 25.0 FGMT314L
Product Codes - Low Pressure Drop Variants
1/2" or 15mm pipe size
GAS
m3/hr Air@ATP
0.3-3.0
FGMT11AG
0.4-4.0
FGMT11BG
0.7-7.0
FGMT11CG
0.9-9.0
FGMT11DG
32
Pressure Loss
m bar
7
10
7
10
1" or 25mm pipe size
GAS
m3/hr Air@ATP
1.5-15 FGMT21AG
3.0-23 FGMT21BG
4.0-36 FGMT21CG
5.0-50 FGMT21DG
www.mess-regeltechnik.at
Pressure Loss
m bar
8
9
8
9
GMT THREADED SERIES FLOWMETER
GMT screwed metal tube magnetically coupled VA
flowmeter. Robust construction for heavy duty. Available
in sizes 1/2" to 2" for gas and liquid flow.
FLOWMETERS
• Brass or stainless steel body
• Economic construction
• BSP/NPT screwed end process connections
• Wide flow ranges
• Pulsation damper fitted as standard on gas
meters to stabilise reading
• Calibration for wide range of gases and liquids
• Low pressure drop versions available with PVC floats on
1/2" and 1" models typically for use with Natural Gas.
Data Sheet DS1221
Specification
Body Materials
Float
Guides
Indicator Housing
Connections
Scale Length
GMTB - Brass
GMTS - 316 Stainless Steel
Stainless Steel or PVC on low
pressure drop units
Stainless Steel
Aluminium Polyester coated,
weather-proofed to IP65
Screwed BSP Female or NPT
Female thread sizes 1/2", 1", 2"
100mm 150° typical
Overall Length
Standard Conditions
Flow Range
Turndown
Accuracy
Hysteresis
Pressure
Temperature
Approvals
250mm
1.013 bar A & 20oC (ATP)
10:1 typical
Typically 10:1
±2% FSD
Less than 0.5%
GMTB: 75 bar, GMTS: 100 bar
200°C max (50°C on low
pressure drop units)
CRN.CSA-OF4812.26
(stainless steel only)
Product Codes
1/2" BSPP Female
GAS - m3/hr Air @ATP
0.5 - 5.0 FGMT*151G
0.75 - 7.5 FGMT*152G
1.2 - 12.0 FGMT*153G
1.8 - 18.0 FGMT*154G
1" BSPP Female
GAS - m3/hr Air @ATP
3 - 30
FGMT*251G
5 - 50
FGMT*252G
10 - 75
FGMT*253G
10 - 120 FGMT*254G
20 - 200 FGMT*255G
2" BSPP Female
GAS - m3/hr Air @ATP
18 to 180 FGMT*351G
30 to 300 FGMT*352G
60 to 600 FGMT*353G
100 to 1000 FGMT*354G
LIQUID - L/hr Water @20°C
20 - 160 FGMT*151L
20 - 250 FGMT*152L
40 - 400 FGMT*153L
60 - 600 FGMT*154L
LIQUID - m3/hr Water @20°C
0.1 - 1.0 FGMT*251L
0.2 - 1.6 FGMT*252L
0.3 - 2.5 FGMT*253L
0.4 - 4.0 FGMT*254L
0.6 -6.0 FGMT*255L
LIQUID 0.6 - 6.0
1.0 - 10.0
2.0 - 16.0
2.0 - 25.0
m3/hr Water @20°C
FGMT*351L
FGMT*352L
FGMT*353L
FGMT*354L
Product Codes - Low Pressure Drop Variants
1/2" or 15mm pipe size
GAS
m3/hr Air@ATP
0.3-3.0
FGMT*15AG
0.4-4.0
FGMT*15BG
0.7-7.0
FGMT*15CG
0.9-9.0
FGMT*15DG
1" or 25mm pipe size
GAS
m3/hr Air@ATP
1.5-15 FGMT*25AG
3.0-23 FGMT*25BG
4.0-36 FGMT*25CG
5.0-50 FGMT*25DG
Pressure Loss
m bar
7
10
7
10
☎
+43 1 706 43 000
Pressure Loss
m bar
8
9
8
9
33
GMT SERIES TRANSMITTER/ALARM OPTIONS
GMTX (Vampire) is an electronic version of the standard GMT metal tube flowmeter,
where the mechanical pointer and scale is replaced with an LCD to give local meter and
digital display of flow rate and flow total. The totally solid state indicator is either loop
powered, or mains AC powered with a 4-20mA output. High and low alarms are shown
on the liquid crystal display panel, and can be signalled to the plant control system.
FLOWMETERS
• Alarms for high and low flow
• CENELEC approved loop powered unit for hazardous areas
• Gas or liquid flows
• 1/2" to 4" line size
• Monitoring process total demand
• Control room monitoring of process flows
• Interface to chart recorders
• Electronic output for plant control
• Rate and total display in flow units
Data Sheets GMTX DS1225
• GMTA DS1220
Specification - GMTX Transmitter
Flow ranges
Display
Analogue scale
Digital display
Flow alarms
Accuracy
Functions with any GMT flow
tube flanged or screwed
Liquid crystal panel
10%-100%, 90mm long
4 1/2" digit display, 10mm high, in
flow units, selectable for flow rate
or total
High and low flow alarm
± 1% Flow rig calibrated
Housing
Model GMTXA
Output
Alarms
Model GMTXD
Supply volts
Alarms
Approval
IP65 Polyester coated aluminium
Power 85-265Vac
4-20mA into 600ohm max
2 x 8A SPCO relays
20mA loop powered CENELEC
approved unit
12Vdc minimum
2 x open collector transistor
EExia IIB T4
Specification - GMTA/GMTAA Alarm
Sensor
Type coding
Type number
Approval
IP Rating
Connection
DIN 19 234 (NAMUR)
SJ2 - N
EExia IIC T6
IP67
2m screened cable (2 cores)
Control Unit
Power supply
Output
Environment
Indicators
Approval
Size
Mounting
115v or 230Vac or 24Vdc models
SPCO Relay 2 Amp at 250V or 40Vdc
Selectable energised/de-energised for alarm
IP20, from -20ºC to 60ºC
Green LED power on
Red LED sensor lead broken
Yellow LED relay energised
(EExia)
115 x 118 x 20
35mm DIN rail or screw fixing
Product Codes - Interface Modules for Alarm Units
For units fitted with alarms and transmitter versions, insert the appropriate code from below before the first number in your selected
code from pages 32 and 33. Example: For the model FGMT113L to be fitted with dual alarms, the code becomes FGMTAA113L.
Description
Single channel Alarm
Dual channel Alarm
AC powered transmitter
DC powered transmitter
Dual channel, 24Vdc supply
34
Code
A
AA
XA
XD
F6001627
Description
Single channel, 110Vac supply
Single channel, 220Vac supply
Single channel, 24Vdc supply
Dual channel, 110Vac supply
Dual channel, 220Vac supply
Code
F6001622
F6001623
F6001626
F6001624
F6001625
www.mess-regeltechnik.at
The Floscan Mains Interface Relay Module is a DIN rail/surface mounted unit that
provides DC power for one or two GIR (Floscan) Infra-red flow alarm sensors (page
28), from any mains power source. Each sensor output drives a relay in the module,
allowing external signalling via the 8 Amp voltage free relay contacts. The two
Floscan sensors can be high or low flow alarms (dictated by the sensor orientation)
and can be on the same
flowmeter tube, or on separate
flowmeters. Energised relay
normal conditions are displayed
by LED indicators. The module
can also be used to power and
monitor alarm outputs from the
GMTXD Transmitter (page 34).
FLOWMETERS
MAINS INTERFACE RELAY MODULE
• High or low flow alarm
• Intelligent: knows whether
float is above or below the
sensor
• LED indicators
• SPCO relay outputs
• DIN rail mountable
Data Sheet DS1120
Specification
Mains Power Input
Sensor Power Output
Floscan Inputs
Relay Output
LEDs
Temperature
Dimensions
20 - 256 Vac, 50/60Hz, 24 - 370 Vdc
+12Vdc, 120mA (suitable for GIR Alarm modules) +24Vdc, 25mA (suitable for GMTXD
transmitter)
Two channel input, independent
8 Amp, 250Vac max de-energised for sensor output open circuit, SPCO action
Green LEDs for no alarm, (relays energised); Yellow LED for power on; Red LEDs to indicate
that float position is unknown (occurs on switch on before float first passes sensor)
-5° to +50°C
70 x 75 x 112mm high
Product Codes
Description
Floscan Mains Interface Relay Module
Code
F58384
☎
+43 1 706 43 000
35
VARIABLE ORIFICE/SWING VANE
FLOWMETERS
Manufactured in a wide range of sizes and specification options but all having the
same basic function. A dial and mechanical indicator continuously monitor the flow
rate, whilst electrical switches can be specified to signal when a particular level has
been reached during increasing or decreasing flows. Switches are field adjustable
over the full range. Where batching, trending, totalisation or recording is required, all
units can be supplied with a 0-10V or 4-20mA output.
• Suitable for gas and liquid applications
• Spring loaded mechanical design requires no straight pipe run and not
affected by orientation
• Modular design - reduces maintenance
costs, down time and production loss
• 1% of rate repeatable switch set point accurate & reliable through all operation
cycles
• Individually calibrated to customer
specification - ensures accuracy
• ATEX certified explosion proof
switches available
• Available in various metals or plastics
Specification
The flow switch body houses a spring loaded valve plate (vane) which pivots off-centre in a hemispherical cavity.
Thus, the vane and cavity have a variable area orifice relationship. This gives both a high flow range and a linear
relationship between flow rate and vane displacement. The vane indirectly operates both the indicating needle
and an adjustable cam, which in turn triggers the micro-switch at any chosen setting of flow-rate. Two switches can
be supplied to provide high and low (or low-low) flow switching.
How to Specify
Please provide the following information to define
your requirements:
•
•
•
•
•
•
•
•
36
Fluid/viscosity/density/specific gravity
Flow range & units
Operating temperature & pressure
Maximum volume flow
Pipe size & connection
Body & seal material
Switch/output requirements
Special requirements
Applications:
•
•
•
•
•
•
•
•
•
Water (clean & dirty)
Water (de-ionised)
Water (de-mineralised)
Petroleum/synthetic based oils
Solvents
Paints
Corrosive fluids
Air & Gases
Coolants
www.mess-regeltechnik.at
Platon AP Purgemeter
GPI Digital Liquid Turbines
For monitoring low flow rates of high
pressure liquids or gases, or where
glass tubes are not suitable,
purgemeters are Stainless Steel in
construction with a magnetically
coupled pointer. They provide direct
flow indication and can be fitted
with flow control valves.
Wide range of economical modular
turbine flowmeters, available in a
variety of connection sizes and
materials. Battery powered digital
display requires no external power.
FLOWMETERS
FLOWMETERS
Data Sheet DS1210
Specification
Specification
Flow tube
End Blocks
Float
Connections
Flow Ranges
Accuracy
Material Options
O-Ring Seals
Meter Housing
Protection
Accuracy
FluidTemperature
Fluid Pressure
Connections
Installation
Approval
316 Stainless Steel
Stainless Steel
Stainless Steel for liquid,
Aluminium for gases
Viton
Aluminium, black anodised body
Polycarbonate window
IP65
VDE/VDI Class 6
-20° to 150°C
40 bar max APV
100 bar max APT/API
1/4" NPT Female
Vertical with flow upwards
CRN.CSA-OF4812.26
Power
Temperature Range
Display
Totaliser
1/2" - 2" NPT or BSPT
4-760 L/min Data Sheet DS1210
Down to ±0.75% of reading
Nylon/Aluminium/Stainless Steel
Brass/PVC/PVDF
Lithium batteries suitable
for 2000 hours of LCD display
External power module available
(Auto powers off when not in use)
-40°C to + 120°C
Local or remote mount
4-20mA/pulse output available
Product Codes
How to Specify
Typical
Water Flow
L/hr
1 - 10
2 - 16
3 - 25
4 - 40
6 - 60
Please contact our Technical Sales Team to discuss your
application
*
•
Typical
Air Flow (ATP)
L/hr
30 - 250
40 - 400
60 - 600
100 - 1000
160 - 1600
Standard
FAPTS 3211*
FAPTS 4211*
FAPTS 5211*
FAPTS 6211*
FAPTS 7211*
Valved
FAPVS 3211*
FAPVS 4211*
FAPVS 5211*
FAPVS 6211*
FAPVS 7211*
In-line
FAPIS3211*
FAPIS4211*
FAPIS5211*
FAPIS6211*
FAPIS7211*
Suffix L for Liquid, G for Gas
Please enquire for flow ranges for alternative fluids
or for higher pressure gases
☎
+43 1 706 43 000
37
FLOWMETERS
FLOWMETERS
High Pressure Liquid
Compressed Air
These metal bodied flowmeters
operate using a spring loaded orifice
moving over a tapered cone, to
achieve a variable area meter. Flow is
indicated by a magnetic follower
ring under a scale on an external
glass tube. The flow reading is
independent of viscosity up to 200 cs.
These metal bodied flowmeters
operate using a spring loaded orifice
moving over a tapered cone, to
achieve a variable area meter. Flow is
indicated by a magnetic follower ring
under a scale on an external glass
tube.
• Calibrated for direct
reading of compressed
air at 7 bar and 20°C
• Works in any orientation
• Brass, Stainless Steel or
Aluminium models
available in 5 sizes
• Pressures up to 41 bar
(600 psi)
• Works in any orientation
• Pressure up to 350 bar
(5000 psi)
• Accuracy ±5% FSD
• Repeatability ±1% FSD
• Direct reading
• Relatively insensitive to
viscosity changes
• Oil or water calibrated
Specification
Connections
Body
Accuracy
Repeatability
Rangeability
Pressure
Temperature
Calibration
Specification
BSP Female
Nickel Plated Brass CZ114
±5% FSD
±1% FSD
10 - 100% FSD
350 bar max
90°C max
Oil (SG 0.856) at 20°C
Water at 20°C
38
BSP Female
Nickel Plated Brass CZ114
±5% FSD
±1% FSD
10 -100% FSD
41 bar max
90°C max
at 7 bar, 20°C
Product Codes
Product Codes
Flow
Range
(L/min)
0.2 - 2
0.5 - 4.5
1-9
2 - 20
5 - 46
5 - 55
10 - 100
Connections
Body
Accuracy
Repeatability
Rangeability
Pressure
Temperature
Calibration
BSP
Conns
Length
(mm)
Water
Code
Oil
Code
1/4"
1/4"
1/4"
1/2"
1/2"
3/4"
3/4"
123
123
123
166
166
190
190
FFLW111
FFLW121
FFLW131
FFLW211
FFLW221
FFLW311
FFLW321
FFLL111
FFLL121
FFLL131
FFLL211
FFLL221
FFLL311
FFLL321
Flow
Ranges
(SCFM)
2 - 20
5 - 50
10 - 100
15 - 125
20 - 225
@ 7 bar G
(L/sec)
BSP
Conns
Length
(mm)
Code
1 - 10
2 - 25
5 - 50
6 - 60
10 -100
1/4"
1/2"
1/2"
3/4"
3/4"
123
166
166
190
190
FFLA111
FFLA211
FFLA221
FFLA311
FFLA321
www.mess-regeltechnik.at
EPW OIL & WATER FLOWMETER
The meter body is in polyester with standard 1" BSP
threads.
• Oil and water calibrated
• Works in any orientation
• Pressures up to 10 bar
• Flows 1 to 150 L/min
• Accuracy ±5% FSD
• Repeatability ±1% FSD
• Switches - fully adjustable flow rate signalling
• Plant and equipment protection
FLOWMETERS
A spring loaded variable orifice meter which can be
mounted in any orientation. Oil or water flow moves the
orifice along a scale printed on the borosilicate glass
tube, to indicate flow rate. Independent of viscosity
changes up to 200 cs.
Specification
Connections
Dimensions
Body
Accuracy
Pressure
Temperature
Electrical switch option
1" BSP Female
Length 196mm, Diameter 60mm
Polyester and Borosilicate Glass
±5% FSD
10 bar max
+5°C to +80°C - oil; +5°C to +60°C - water
Adjustable 20% -100% full scale
Product Codes
Water Flow (20°C)
1 - 15 L/min
2 - 30 L/min
4 - 50 L/min
5 - 100 L/min
10 - 150 L/min
Meter Alone
FEFW0152
FEFW0302
FEFW0502
FEFW1002
FEFW1502
with AC /DC Switch
FEFW0152B
FEFW0302B
FEFW0502B
FEFW1002B
FEFW1502B
Oil Flow (SG 0.856) (20°C)
1 - 15 L/min
2 - 30 L/min
4 - 50 L/min
5 - 100 L/min
10 - 150 L/min
FEFL0151
FEFL0301
FEFL0501
FEFL1001
FEFL1501
FEFL0151B
FEFL0301B
FEFL0501B
FEFL1001B
FEFL1501B
•
The external alarm circuit should provide latching functions
☎
+43 1 706 43 000
39
STAINLESS STEEL TURBINE & PELTON WHEEL
FLOWMETERS
A range of Stainless Steel turbine flowmeters capable of
measuring flow rates of water and low to medium viscosity
oils and other liquids in high pressure applications.
Providing an electrical pulse output, these meters when
linked to a display unit provide accurate and high
repeatability flow measurement.
The NS Series utilises the Pelton Wheel principle to provide
accurate flow measurement down to 0.18 L/min. High
accuracy measurement is provided by the NT Series for up
to 6" lines. For hygienic applications, the BNO series offers
the same high accuracy, in a ‘bug-trap’ free design. Stem
mounted displays are available on page 41.
• Flow rates from 0.18 - 10000 L/min
• High accuracy/excellent reliability
• Industrial & hygienic versions
• Wide range of end connections available
• Now available for gas applications
• Reverse and dual pick-up options available
on request
Specification
Accuracy
Repeatability
Output
Electrical Connections
Pressure Drop
Temperature
NT & BNO ±0.5%
NS ±1%
NT & BNO ±0.1%
NS ±0.25%
Sinusoidal pulses, 50 to 800mV
2-way Amphenol connector
0.2 to 0.5 bar, depending
on meter size
150°C max (high temp
versions available)
Pressure
Wetted Materials
300 bar max
Stainless Steel, Tungsten
Carbide & Carbon filled
PTFE (NS Series includes a
Butyl rubber O-ring)
NS and NT Series screwed models are also available with
flanges, and BNO Series meters with RJT and ISS hygienic
type fittings. Spare pick-up coils are also available.
Please consult our Technical Sales Team.
Product Codes
Process
Connections
Flow Range
(L/min)
(Pulses/ Code
Litre)
NT Series Turbine Flowmeters
3/8"BSP Male
0.5 - 5
17000
1/2" BSP Male
1.2 - 10
5900
1/2" BSP Male
2 - 20
3000
1/2" BSP Male
5 - 50
2600
3/4" BSP Male
8 - 80
1950
1" BSP Male
15 - 150
630
1" BSP Male
25 - 250
350
65 - 650
117
11⁄2" BSP Male
2" BSP Male
110 - 1100
67
NS Series Pelton Wheel Flowmeters
3/4" BSP Male
0.18 - 1.8
20700
3/4" BSP Male
0.45 - 3.2
14500
3/4" BSP Male
1.1 - 5.4
12500
3/4" BSP Male
1.3 - 6.5
10500
40
Process
Connections
FFTB0012
FNT5
FNT7
FNT11
FNT13
FNT19
FNT24
FNT38
FNT48
FFTB0004
FFTB0005
FFTB0006
FFTB0007
Flow Range
(L/min)
21⁄2" ANSI 150
Flanges
200 - 2000
3" ANSI 150
Flanges
300 - 3000
4" ANSI 150
Flanges
500 - 5000
6" ANSI 150
Flanges
1000 - 10000
BNO Series Hygienic Flowmeters
1/2" Tri-clamp
2 - 20
1" Tri-clamp
9 - 90
1" Tri-clamp
18 - 180
25 - 250
11⁄2" Tri-clamp
2" Tri-clamp
65 - 650
(Pulses/ Code
Litre)
18
FFTB0008
14
FFTB0009
7.5
FFTB0010
3.4
FFTB0011
2800
1000
330
240
90
FFTB0013
FBNO500
FBNO1000
FBNO1500
FBNO36
www.mess-regeltechnik.at
The FW Series of digital indicators is specially
designed for computing and displaying
total and instantaneous flow rates in liquid
or gas applications. Versions are available
for either pulse or analogue inputs, and a
batch controller is available for pulse inputs.
Housed within a rugged, powder-coated
aluminium enclosure that is suitable for direct
mounting to a flowmeter, pipe, wall or panel.
• Units are also available mounted directly to the Turbine Liquid Flowmeters on page 40
• These units are also available in intrinsically safe and panel mounted versions
FLOWMETERS
DIGITAL INDICATORS
Specification
Display
Programming
Data Protection
Input:
Pulse
Analogue
Outputs: Pulse
Analogue
Power Supply
Temperature
Housing
Protection
Dimensions
Panel Cut-Out
Cable Entry
Batcher Outputs
Overrun Correction
Remote Input
Alarm Unit
Remote Input
Relays/Supply
Serial Comms
Large 40 x 90mm LCD with 7 x 17mm digits & 11 x 8mm digits
Flow - up to 7 digits, Total - 7 digits, Accum. Total - 11 digits
Via keypad
10 year data retention minimum (total stored at 10 min intervals)
Sine wave, NPN/PNP open collector, reed-switch or NAMUR 0 to 10kHz
(selectable de-bounce for low frequencies)
4-20mA or 0 to 10Vdc with linear or square-root functions
Open collector output, scaleable pulse per unit, 20Hz max, 50Vdc, 300mA max,
25 or 100msec pulse width
Passive 4-20mA
7 year lithium battery (4-20mA loop or 5 to 24Vdc, if required)
-15ºC to 60ºC
UV resistant powder-coated Aluminium casing, SS bolts, Polycarbonate window,
EPDM, and PE seals
IP67 (IP65 when panel mounted)
130 x 114 x 58mm
115 x 96mm (L x H)
1 x M20 and 2 x Pg9 cable glands
Two open collector outputs for one/two stage control 50Vdc, 300mA max
Automatic
One input for Start/Stop batch
Outputs: 2 x open collector outputs programmable as high/low alarms or pulse
output 50Vdc, 300mA max
Reset of total quantity or batch total
12 to 24Vac/dc or 80 to 240Vac supply
Relays: 250Vac/1A max
Sensor supply: 8.1 to 24Vdc, 80mA max @24V
RS232/RS485
Product Codes
Description
Pulse input 4-20mA output
Pulse input with High/Low alarms
Pulse input with 15-point linearisation
Dual pulse input (no outputs)
Code
FDIS0090
FDIS0091
FDIS0092
FDIS0093
☎
Description
Dual pulse input with ratio function
Dual pulse input with A-B or A+B functions
Pulse input Batch Controller
+43 1 706 43 000
Code
FDIS0094
FDIS0095
FDIS0096
41
MODEL 910 ELECTROMAGNETIC FLOWMETER
FLOWMETERS
The Model 910 Electromagnetic Flowmeter is an instrument designed for
measuring and indicating flow and total volume of conducting liquids. It boasts
diagnostic, real time and data logging
features. The flowmeter is available in both
compact and remote mount versions.
• Highly accurate
• No moving parts in the flow profile
• Configuration data is backed up and
can be recovered
• Datalogging function
• Diagnostic facility
Specification - Model 910 Transmitter
Min. Media Electrical Conductivity
Flow Range
Accuracy
Power Supply
Power Consumption
Outputs
Input
Communication
Control
Electronics Protection
Housing Material
Flow Direction
Diagnostics
Real Time
Datalogger
Hazardous Area Approval
Control Principle
Cable Terminals
≥5 µS/cm / ≥20 µS/cm for demineralised water
0.1 to 10 m/s
0.5% (0.5 to 10 m/s) of reading value, 1% (0.1 to 0.5 m/s) of reading value
95 to 250 Vac 50/60 Hz (+10%, -15%) 12,14, 48 Vac/dc (Model 910E)(115/230V/24V D Model 910)
10 VA
• Frequency 0 to 12 kHz with programmable flowrate and function
• Pulse 0 to 50 Hz with programmable volume, function and pulse width
• Relay contacts 100V/0.5A with programmable function (as option)
• Current 4 to 20 mA with programmable flowrate and function Max 500 Ω
Digital input with programmable function
RS485, RS232
RS485, RS232, keyboard and magnetic pointer (MAG910E RS232)
Standard IP67/ Nema 5 (IP68/Nema 6 optional)
Cast Aluminium
Bi-directional measurement
Diagnostic of internal temperature and power supply voltages
Real time circuit for datalogging
• Datalogger memory up to 15000 values (programmable sample rate)
• Registration of minimum and maximum flowrate including date and time
Zone 2 pending
Pulsed DC from transmitter
2 pieces PG11
Specification - Model 910 Sensor
Flange
Nominal Size
Maximum Nominal Pressure
Max Media Temperature
Ambient Temperature
Sensor Protection
Liner
Measuring Tube
Hazardous Area Approval
Outer Casting
External Coating
Conformity requirements
Electrode
Steel 1.0402 or higher
10 .. 800mm
1.0 MPa - 2.5 MPa (10,16,25 bar)
70oC (158oF) for hard rubber liner
130oC (266oF) for PTFE liner in remote version
-20 to 60oC (-4 to 140oF)
Standard IP67/Nema 5 (IP68/Nema 6 optional)
Hard rubber, PTFE
Stainless Steel 1.4201, dimensions according to DIN 17457
Zone 2 pending
Carbon Steel as standard
Lacquered finish (anticorrosive)
PED according to directive 97/23/EC
MAG910 Cr Ni, ST-ST 1.4571 Hastelloy C276 (Mag910E option=Tantalum)
How to Specify
Please contact our Technical Sales Team to discuss your application
42
www.mess-regeltechnik.at
The MagX1 flowmeter has an advantage over conventional electromagnetic
technologies in that the sensor element converts the sensed signal into digital
format. This enables the signal to be transmitted over much longer distances (up to
500 metres) than possible with analogue transmission. The sensor also has an
automatic self-diagnosis feature which allows any sensor problems to be reported
on the transmitter display.
• Digital signal for remote transmission
• Self-diagnostic tool for sensor
• Indicative temperature measurement
•
•
FLOWMETERS
MAG X1 ELECTROMAGNETIC FLOWMETER
and automatic temperature compensation
Empty pipe detection
Sensor ingress protection of IP67 (compact) or
IP68 (remote)
Specification
Items
Analogue output
Option 1
Analogue output
Option 2
Analogue output
Option 3
Communication options
Data-logger
Real Time Clock
Possible options
4-20mA current output signal module
0-10 V voltage output signal module
Frequency output module
Binary in/output module (1x input signal for batching + 2x output signal)
RS232 communication module, including cable
USB communication module, including cable
IRDA wireless infra-red communication transmitter module, max. distance 2m
Wireless communication module (antenna), max. distance 20m indoor, 100m in
open space, including receiver with USB connection
RS485 communication module, max. distance up to 1km
TCP/IP communication module, distance practically unrestricted
(as given by TCP/IP technology), amplifiers might be necessary
Memory/Data-logger module, 1MB capacity; 5 minute average flow-rate
sampling intervals; 12-month data capacity
Real Time Clock (RTC) module, current date and time
How to Specify
Please contact our Technical Sales Team to discuss your application
☎
+43 1 706 43 000
43
MODEL 220 PORTABLE ULTRASONIC FLOWMETER
This portable device has been designed to meet the needs of the
Service/Maintenance and Commissioning Engineer who wishes to check the flow rate
of liquids at different locations in the plant. The set-up of the unit is simple and user
friendly with the required flow information obtained in minutes.
FLOWMETERS
The ultrasonic sensors are clamped
onto the outside of the pipe, thus
eliminating the need to dismantle the
pipework and interrupt the process.
• Portable dual mode flowmeter
• Easy to install clamp-on sensors with
no process interruption
• Non-invasive flow measurement of
liquids, no pipeline disturbance or
pressure loss
• Suitable for all commonly used pipe
materials with pipe diameters from
6mm to 6.5m (1/4" to 256")
• Integrated wall thickness measurement
• 2 flow channels as standard
Specification
Measuring Principle
Flow Velocity Range
Resolution
Repeatibility
Accuracy:
Volume Flow
Flow Velocity
Rangeability
Turn-down Ratio
Measurable Liquids
Ultrasonic time difference correlation principle and Doppler-NoiseTrek™
0.01 - 25 m/s
0.25 mm/s
0.15% of measured value ± 0.01 m/s
± 1 - 3% of measured value depending on application,
± 0.5% of measured value with process calibration
± 0.5% of measured value
1/2500
1/100
All acoustically conductive liquids with a gas or solid content of < 10% of volume
How to Specify
Please contact our Technical Sales Team to discuss your application for Models 220, 110 and 160
44
www.mess-regeltechnik.at
Ultrasonic Flowmeter Model 110
Ultrasonic Flowmeter Model 160
The field mounted flow transmitter
can be configured via the keypad
without any additional programming
devices and is available as a single
channel unit. The ultrasonic sensors
are clamped onto the outside of the
pipe, thus eliminating the need to
dismantle the pipework and interrupt
the process.
The field transmitter has been
designed for permanent installations
in potentially explosive atmospheres
and for field application with harsh
environmental conditions. Opening
the enclosure is not necessary for
instrument set-up and operation. A
separate hand-held remote control or
laptop computer is not required. The
ultrasonic sensors are clamped onto
the outside of the pipe,thus eliminating
the need to dismantle the pipework
and interrupt the process.
• Ultrasonic flowmeter
in IP66 wall mounted enclosure
• Easy to install clamp-on sensors
with no process interruption
• Non-invasive flow measurement of
liquids, no pipeline disturbance, no
pressure loss
• Suitable for all commonly used
pipe materials with pipe diameters
from 10mm to 2.5m (1/2" to 100")
• Dual mode flow transmitter
• Non-invasive flow measurement of
liquids, no pipeline disturbance, no
pressure loss
• Suitable for all commonly used
pipe materials with pipe diameters
from 10mm to 3m (2/5" to 118")
• 1 or 2 flow channels,
IP 66 field enclosure
• ATEX certified for
hazardous areas
Zone 1&2
EEx DE
2CT6
Specification
Specification
Measuring Principle Ultrasonic time difference
correlation principle
Flow Velocity Range 0.01 - 25 m/s
Resolution
0.25 cm/s
Repeatibility
0.15% of measured
value ± 0.01 m/s
Accuracy:
Volume Flow ± 1 - 3% of measured value
depending on application,
± 0.5% of measured value
with process calibration
Flow Velocity ± 0.5% of measured value
Turn down Ratio
1/100
Gaseous and solid
content of medium < 10% of volume
Measuring Principle Ultrasonic transit-time correlation
principle and Doppler-NoiseTrek™
Flow Velocity Range 0.01 - 25 m/s
Resolution
0.25 cm/s
Repeatibility
0.15% of measured
value ± 0.01 m/s
Accuracy:
Volume Flow ± 1 - 3% of measured value
depending on application,
± 0.5% ± 1.0 cm/s of measured
value with process calibration
Flow Velocity
± 0.5% ± 1.0 cm/s of
measured value
Rangeability
1/2500
Turn down Ratio
1/100
Gaseous and solid
content of medium < 10% of volume
☎
FLOWMETERS
FIELD MOUNT ULTRASONIC FLOWMETERS
+43 1 706 43 000
45
ULTRASONIC FLOWMETER/SWITCH
FLOWMETERS
Solid state flow switch provides a highly accurate monitoring and control solution for
water-based fluids. Our UQS7 combines two built-in switchpoints, a 4-20mA
analogue output, and a digital display in a single, compact unit. Ultrasonic sensing
technology measures time of flight between two discrete points, assuring highly
accurate measurement with low insertion loss as compared to other types of flow
sensor. Setpoints and dead-band are easily adjusted by using a built-in, userfriendly menu. Analogue output is scalable from 25% to 100% of full scale range,
providing a high degree of flexibility for a wide range of applications. A 10 -bit
microprocessor provides built-in self diagnostics and allows for switch time delays up
to 9.9 seconds. For applications requiring accurate monitoring of water-based fluids,
the UQS7 is an ideal choice.
Features
• Integrated 4-20mA analogue output
• Easy to read LED display
• Fully configurable via keypad
• Suitable for water-based fluids
• IP 65 protection
• 7 digit LED display
• Tamper-proof keypad lock
• Rotable display
46
www.mess-regeltechnik.at
ULTRASONIC FLOWMETER/SWITCH
Specification
Ultrasonic sensor
Water and similar media
max. pressure 360 psi (25 bar)
(higher pressures on request)
Materials
Wetted parts
Housing (Electronics)
Seals (Media)
Pushbuttons
Operating Elements
Protection/Class
Pressure Connection
Dimensions
Measure Ranges
g/min
L/min
Linearity Error
A/D-Connector
Scanning Rate
Electrical Connection
Temperature Influence
Compensation Range
Repeatability
Temperature Range
Electronics
Storage
Inlet-Outflow Zone
Power Supply
Digital Display
4-digit 7-segment LED-display
height 0.5 in., red
500 mS
LED yellow and alphanumeric display,
Brass
(diagnosis function acc.DESINA®
Aluminum die-cast
Power Consumption appr.50 mA (without load)
Klingersil®
Analogue Output
Polyester
Scanning Rate
500mS
3 easy responses pushbuttons Resolution
10 bit (1024 steps per measuring span)
IP65
Current Output
4-20 mA
3/4, 1, 1 1/4, 2 BSPP
Load
max. RI = (Ub-12V)/20 mA
3.9in x 4.3in (UQS7-10)
RI=600 Ohm at Ub=24 Vdc
Load Influence
0.3%/100 Ohms
2.6/6.6/10.5/26.4/44.9
Options
(10/25/40/100/170)
Voltage Output
0 to 10 Vdc
±2.5% f.s. at 77ºF (+25ºC)
Rating
max. 10 mA, short circuit-proof
Adjustment Range
25% to 100% f.s.
500 ms (for peak value memory) Switching Output(s)
Plug M 12 x 1, 5-pin,
Switching Function Normally open/normally closed,
DESINA® conformity
-(adjustable)
standard/windows-mode
±0.2% f.s./10K
Adjustment Range
0% to 125% f.s.
14ºF to 158ºF (-10º to +70ºC)
Hysteresis
0% to 125% f.s.
±0.1% f.s.
Diagnosis Function
SP2 (DESINA® model)
39ºF to 266ºF
Switching Frequenccy max. 100Hz
14ºF to 158ºF
Rating
max. 500 mA, short circuit-proof
-22ºF to 176ºF
Delay
0.0 to 9.9 s adjustable
Integrated in the measuring device Status Display(s)
LED(s) green
15-32 Vdc,reversed polarity protected Options
Electrical plug, adapters
Display Rate
Error Display
FLOWMETERS
Sensor Element
Media
Product Codes
Model
Flow Rate
(L/min)
DIM“A”
DIM“B”
Process
Connection
Switch
Points
Analogue Output DESINA®
(4-20mA)
Signal
FUQS7-10-G3-2
FUQS7-10-G3-3
FUQS7-25-G3-2
FUQS7-25-G3-3
FUQS7-40-G4-2
FUQS7-40-G4-3
FUQS7-100-G5-2
FUQS7-100-G5-3
FUQS7-170-G8-2
FUQS7-170-G8-3
.04 to 10
.0.4 to 10
.1 to 25
.1 to 25
.16 to 40
.16 to 40
.4 to 100
.4 to 100
.4 to 170
.4 to 170
4.3 (110)
4.3 (110)
4.3 (110)
4.3 (110)
7.5 (190)
7.5 (190)
10.2 (260)
10.2 (260)
11.8 (300)
11.8 (300)
3.9 (100)
3.9 (100)
3.9 (100)
3.9 (100)
3.9 (100)
3.9 (100)
5.1 (130)
5.1 (130)
5.3 (135)
5.3 (135)
G 3/4 BSPP
G 3/4 BSPP
G 3/4 BSPP
G 3/4 BSPP
G1 BSPP
G1 BSPP
G 1-1/4 BSPP
G 1-1/4BSPP
G2 BSPP
G2 BSPP
2
2
2
2
2
2
2
YES
2
2
n/a
YES
n/a
YES
n/a
YES
n/a
n/a
n/a
YES
1
n/a
1
n/a
1
n/a
1
1
n/a
Accessories
Mating electrical connector (not included) F239263
Notes
Standard flow ranges x2 available at 3% FSD
☎
+43 1 706 43 000
47
LAMINAR WATER FLOW TRANSMITTER
FLOWMETERS
The L Series Water Flow Transmitters are designed
for demanding DI Water, or other clean water
applications. Differential pressure, fluid pressure
and temperature are measured in the laminar flow
channel. This information is then used to calculate
the volumetric flow rate of the liquid. All of the
above parameters are dynamically displayed and
output via the RS232 interface. An analogue output
is also included.
• Response time of 20 milliseconds typical
• Turndown ratio of 50:1
• Push button interface
• Accuracy of ±2% FSD
• RS232 interface
Data Sheet DS1731
Specification
Process Connections
Accuracy
Repeatability
Response Time
Turndown Ratio
Pressure Drop
Pressure
Temperature
Wetted Materials
10-32 UNF 1/8" and 1/4" NPT female
±2% FSD
±2% FSD
20 ms
50:1
0.8 psi
100 psig max
50°C max
Stainless Steel, Viton, Silicon Gel,
Nylon & Polyethermide
Power Supply
Outputs
7 - 30 Vdc, 30mA typical
0 - 5 Vdc (4 - 20mA or
0 - 10 Vdc optional)
2m long 8-core lead
Graphic LCD
RS-232
Electrical Connection
Display
Digital Output
Dimensions D x W x H
0.01 - 500cm3/min 27 x 61 x 99mm
0.02 - 10 L/min
27 x 61 x 104mm
Product Codes
Range
(cm3/min)
0.01 - 0.5
0.02 - 1
0.04 - 2
0.1 - 5
0.2 - 10
0.4 - 20
0.6 - 30
1 - 50
4 - 200
10 - 500
•
•
•
48
Connections
Codes
10-32UNF
10-32UNF
1/8" NPTF
1/8" NPTF
1/8" NPTF
1/8" NPTF
1/8" NPTF
1/8" NPTF
1/8" NPTF
1/8" NPTF
FFLM0000
FFLM0001
FFLM0002
FFLM0003
FFLM0004
FFLM0005
FFLM0006
FFLM0007
FFLM0008
FFLM0009
Range
(L/min)
0.02 - 1
0.04 - 2
0.06 - 3
0.1 - 5
0.2 - 10
Connection
Code
1/8" NPTF
1/4" NPTF
1/4" NPTF
1/4" NPTF
1/4" NPTF
FFLM0010
FFLM0011
FFLM0012
FFLM0013
FFLM0014
Blind units are available, also other outputs and flow ranges
Flow controller option available using proportional valve coupled to flowmeter body
Please contact our Technical Sales Team for more details
www.mess-regeltechnik.at
LAMINAR GAS FLOW TRANSMITTER
FLOWMETERS
The M Series Mass Gas Flow and V
Series Volumetric Gas Flow
Transmitters measure differential
pressure within the laminar flow
channel to produce an inherently
linear flow reading. Combined
with low response time, multiple
outputs, dynamic display and 20
user selectable gas calibrations,
these units out-perform most
thermal type meters.
M Series incorporates temperature
and absolute pressure measurements
to determine mass flow.
V Series is designed for low
pressure applications venting to
atmosphere or with little back
pressure.
• Response time of 10 milliseconds
• Push button interface
• Accuracy of ±0.8% of reading
• 20 standard gas calibrations included
(adjustable)
• Turndown ratio of 100:1
Data Sheet DS1730
Specification
Process Connections
Accuracy
Repeatability
Adjustable Resp Time
Turndown Ratio
Pressure Drop
Pressure
Temperature
Wetted Materials
Power Supply
Output
10-32UNF and NPT female
±0.8% of reading
±0.2% FSD
10 msec
100:1
<28mbar up to 505 L/min
<200mbar up to 1000 L/min
145 psig max
50°C max
Aluminium, Stainless Steel ,Viton,
Silicon Gel & Nylon
7 - 30 Vdc, 30mA typ.
0 - 5 Vdc (4 - 20mA or
0-10 Vdc optional)
Electrical Connection 2m long 8-core lead
Display
Graphic LCD
Dimensions D x W x H
0.005 - 50cm3/min= 27 x 61 x 99mm
1cm - 20 L/min = 27 x 61 x 106mm
0.5 - 100 L/min = 41 x 102 x 111mm
2.5 - 1000 L/min = 41 x 102 x 127mm
20 gas calibrations included: argon, butane, carbon dioxide,
carbon monoxide, ethane, helium, hydrogen, iso-butane,
krypton, methane, neon, nitric oxide, nitrogen, nitrous
oxide, oxygen, propane, sulphur hexafluoride & xenon.
How to Specify
•
•
•
Blind units are available, also other outputs and flow ranges
Flow controller option available using proportional valve coupled to flowmeter body
Please contact our Technical Sales Team for more details
☎
+43 1 706 43 000
49
FLOWMETERS
FLOWMETERS
In-line Pitot “Flo-bar”Pipe Section
Insertion Pitot Tube
Stainless Steel pipe sections with
welded-in pitot probes, available for
1/2" to 2" pipes. Supplied fitted with
1/4" ball valves to provide process
isolation.
Flo-Bar tubes contain no moving parts.
Standard models are manufactured
from Stainless Steel, though alternative
material requirements are readily
accommodated.
• Flow sensors for liquids or gases
• ±1% of actual flow rate
• Full electron beam welded
• Flow sensor for liquids or gases
• ±1% of actual flow rate
• Full electron beam welded
construction
construction
• Unique profiled sensor with flow
• Flow averaging
• Integral isolation ball valve
• No power supply required
averaging
• Integral 3 valve manifold
• Mounting of DP transmitter if required
Data Sheet DS1710
Specification
Specification
Material
Repeatability
Output
Probe Diameter
Temperature
Range
Tappings
Pipe Connection
Pressure
Pipe Size
50
Stainless Steel
±0.1% (typical)
DP (proportional to the
square of fluid velocity)
-20°C to 225°C insertion
model
0.7 to 250 m3/hr (air @ ATP),
0.1 to 65 m3/hr (water @ 20°C)
1/4" BSP
Threaded NPT Male
30 bar max
1/2" to 2" nominal bore Sch 80
25mm standard,100mm-3000mm pipes,
13mm for 50-449mm dia pipes
60mm for pipes over 3000mm ID
Material
Stainless Steel, electron beam
welded construction
Averaging Sensor Typically 6 upstream ports for
flow averaging
Installation
7 diameters downstream, 3
diameters upstream (minimum)
of a bend or similar obstruction
Connections
1" NPT Female on 54mm centres
from integral 3 valve manifold
Flow Repeatability ±0.1%
Pressure Max
To flange rating 5 bar max for
compression fitting
How to Specify
How to Specify
Please specify with enquiry:
• Pipe ID and OD
• Preferred connection screwed/flanged
• Flowing fluid and conditions
• Line pressure and temperature
• Output and display preferred
Please specify with enquiry:
• Pipe ID and OD
• Preferred connection screwed/flanged
• Flowing fluid and conditions
• Line pressure and temperature
• Output and display preferred
www.mess-regeltechnik.at
Water Meter
Oil Meter
Designed for use with clear and
translucent water at up to 40°C. This
range of water meters provide
measurement of water flow by means
of a mechanical totalisation counter.
They are stand-alone units which
require no mains power.
For fuel consumption measurement
the VZO meters are available from
1/8" to 1", giving a totalised value of
flow on the mechanically driven
dials. The meter is unaffected by
viscosity change or installation
orientation: it can be installed on the
pressure or suction side of a pump.
• Single port for dedicated pipeline
flow monitoring
• 1% accuracy over full measurement
• Direct read out for on-site control
• Optional pulse
range
FLOWMETERS
FLOWMETERS
• Tamper proof roller counter
• Installation in any orientation
• Optional pulse output
output
• Tamper proof
non-resettable
counter
Specification
Accuracy
Material
Pressure
Temperature
Wetted Parts
Installation
2% FSD over 95% of flow range
Brass body
10/16 bar max
Max temp 40°C
Drinking water approved
(75/33/EEC)
Horizontal or vertical
Product Codes
Connection dia (bore) mm
Pipe fittings inches
Typical flowrate max m3/h
Typical stall speeds
(Min flow) L/hr
Min flowrate (±2% error) L/hr
Connection dia (bore) mm
Pipe fittings inches
Typical flowrate max m3/h
Typical stall speeds
(Min flow) L/hr
Min flowrate (±2% error) L/hr
Dial registers from/to
Test pressure Kg/cm2
FWM15
15
1/2"
3
FWM20
20
3/4"
3
FWM25
25
1"
7
10
150
15
250
30
350
FWM30
30
1 1/4"
10
FWM40
40
1 1/2"
20
FWM50
50
2"
30
40
500
70
1000
95
1500
0.001/10,000
25
Note: Max flow rate quoted has pressure drop of 10 metres W.G.
☎
Specification
VZO4/VZO8 meters
Size
Connections
Pressure
Temperature
Format
1/8" & 1/4"
BSP Female in meter base
25 bar max
60°C max
Compact cubic design
VZO15/20/25 meters
Size
Connections
Pressure
Temperature
Format
1/2", 3/4" & 1"
BSP Male in line
16 bar max
130°C max
As photo with meter cover
Product Codes
BSP
Conns
Size
1/8"
1/4"
1/2"
3/4"
1"
Flow
Max
L/hr
80
200
600
1500
3000
Flow
Min
L/hr
1
4
10
30
75
+43 1 706 43 000
Rec’d Max
Continuous
Flow L/hr
50
135
400
1000
2000
Start Up
Flow
L/hr
0.5
1.6
4
12
30
Code
FVZO4
FVZO8
FVZO15
FVZO20
FVZO25
51
PRE-SET FLOW CONTROLLER
FLOWMETERS
Flow control valves for pure liquid applications which provide a constant pre-set flow
rate, independent of line pressure changes. Operation is by means of a rubber orifice
that reduces in size as the pressure increases, thus balancing the flow. Installation is
possible on pipework in any plane to fit existing pipework. Available either screwed,
for lines up to 2", or as a wafer to fit between flanges. All materials are WRC approved
for use in drinking water systems.
• Maintains controlled water supply irrespective
of pressure fluctuation
• Reduces pressure surge & water wastage
• Helps eliminate costly water bills
• Ease of installation & operation
Specification
Body Material
Brass or Stainless Steel
(UPVC option available)
BSP Female
Fit between BS10 Table E
flanges
Screwed body
Wafer body
Temperature
Pressure
Differential Pressure
Rubber Controller
Accuracy
-25°C to 100°C
16 bar max
6.5 bar max
Nitrile
±10%
Product Codes
Threaded:Pipe Set Flow
Size (L/min)
1/2" 0.4
1/2" 0.7
1/2" 1.0
1/2" 1.5
1/2" 2.0
1/2" 3.5
1/2" 5.0
1/2" 7.0
1/2" 10.0
1/2" 15.0
1/2" 23.0
3/4" 32.0
3/4" 41.0
3/4" 54.0
Brass Body
SS Body
F59290004
F59290007
F59290010
F59290015
F59290020
F59290035
F59290050
F59290070
F59290100
F59290150
F59290230
F59290320
F59290410
F59290540
FVFC0004
FVFC0005
FVFC0006
FVFC0007
FVFC0008
FVFC0009
FVFC0010
FVFC0011
FVFC0012
FVFC0013
FVFC0014
FVFC0015
FVFC0016
FVFC0017
1"
1"
1"
11⁄2"
11⁄2"
2"
2"
73.0
91.0
114
160
200
200
230
Water:Pipe Set Flow
Size (L/min)
2"
342
21⁄2" 456
3"
675
4"
1080
5"
1620
6"
2565
F59290730
F59290910
F59291140
FVFC0000
FVFC0001
FVFC0002
FVFC0003
FVFC0018
FVFC0019
FVFC0020
FVFC0021
FVFC0022
FVFC0023
FVFC0024
Brass
SS
FWFC20
FWFC25
FWFC30
FWFC40
FWFC50
FWFC60
FVFC0025
FVFC0026
FVFC0027
FVFC0028
FVFC0029
FVFC0030
PVC Versions available on request
52
www.mess-regeltechnik.at
MN & FV AUTOMATIC FLOW CONTROLLERS
Specify option ‘A’ for all liquid applications and gas applications where pressure
fluctuations occur downstream, or option ‘B’ where supply pressures only are
subject to fluctuation.
• Entirely automatic- no external power needed
• Suitable for use on hazardous fluids - intrinsically safe
• High response speed for close flow control
• 10:1 control range
• High long term reliability
• 1/4” to 4” sizes as standard
Data Sheets MN DS1511
Specification - MN
Specification - FV
Body Material
Polyester coated Brass
or 316 Stainless Steel
Diaphragm and Seals Brass body - Nitrile
SS body - PTFE
Temperature
Nitrile 80°C, PTFE 100°C
Pressure
Brass/Nitrile 20 bar max
SS/PTFE 28 bar max
Process Connection
1/4" BSPP female
Repeatability
±1%
Accuracy
Liquids: ±2%
Gases: ±3%
Body Material
Product Codes
Product Codes
Flow Ranges
Air@ATP (L/min) Water@20°C (L/min)
Brass
0.005 - 5
0.002 - 0.2
0.1 - 30
0.05 - 1.5
8 - 100
0.25 - 3.5
Stainless Steel
0.005 - 5
0.002 - 0.2
0.1 - 30
0.05 - 1.5
8 - 100
0.25 - 3.5
Spare Kits
MN Nitrile Diaphragms & Seals
MN PTFE Diaphragms & Seals
• FV DS1521
Epoxy coated Brass or
316 Stainless Steel
Diaphragm and Seals Brass body - Nitrile
SS body - PTFE
Temperature
Nitrile 80°C, PTFE 100°C
Pressure
16 bar max or flange
rating if lower
Process Connection 1/2" - 3/4" BSPP Female
1" - 4" flanged to BS, DIN
or ANSI
Repeatability
±1%
Accuracy
Liquids: ±2% Gases: ±3%
Type A Code Type B Code
FMNAB11
FMNAB21
FMNAB31
FMNBB11
FMNBB21
FMNAS12
FMNAS22
FMNAS32
FMNBB11
FMNBB21
FMNAKN
FMNAKP
FMNBKN
FMNBKP
☎
FLOWMETERS
Flostats maintain liquid or gas flow at a pre-selected rate regardless of line pressure
fluctuations. Using an internal orifice to measure flow, the differential pressure produced drives an internal control valve. Only a small pressure drop in the line is
required for satisfactory operation.
Flow Ranges
Air@ATP (L/min) Water@20°C (L/min)
Brass
13 - 133
0.3 - 4.5
20 - 200
0.6 - 6.5
40 - 400
1.3 - 13
Stainless Steel
13 - 133
0.3 - 4.5
20 - 200
0.6 - 6.5
40 - 400
1.3 - 13
Spare Kits
MN Nitrile Diaphragms & Seals
MN PTFE Diaphragms & Seals
+43 1 706 43 000
Type A Code Type B Code
FFVAB11
FFVAB13
FFVAB13
FFVBB11
FFVBB12
FFVBB13
FFVAS21
FFVAS22
FFVAS23
FFVBS21
FFVBS22
FFVBS23
FFVAK0.5N
FFVAK0.5P
FFVBK0.5N
FFVBK0.5P
53
AUTOMATIC FLOW CONTROLLERS
Platon B and LB Flostats
Specification
FLOWMETERS
Body Material
Valve Trim
Diaphragm
Temperature
Pressure
Maximum Pressure Drop
Process Connection
Reproducibility
Control Accuracy
Adjustment
Actuation
Epoxy coated Mild Steel or Stainless Steel
Stainless Steel
Nitrile
80°C max
20 bar max or flange rating if lower
5 to 10.5 bar depending on flostat size
2" to 6" flanged to BS, DIN or ANSI
±2%
±5%
Plain or with scale plate, or factory pre-set
Manual or pneumatic
How to Specify
Data Sheet DS1531
Contact our Technical Sales Team with
the following information:
• Pipe size
• Fluid type, SG and viscosity if unusual
• Body and diaphragm materials
• Flow range
• Flange type
• Fluid temperature and pressure
Features
•
•
•
•
•
•
Fully automatic
10:1 control range
No power required
Simple and reliable
Fast response
High accuracy
Automatic Flow Controller
• Ideally suited to welding, brewing and
control applications
• Entirely automatic - no external power
needed
• High response speed for close flow control
• High long term reliability
• Wide rangeability - adjust to site requirements
• Designs in anodised aluminium and
brass typically
• Wide range of flow control from 10 to 5000 L/min
Ideal for maintaining gas flow at a pre-selected rate, when down stream pressure
fluctuates. Control is based on flow measurement using an internal orifice.This means
that the controller requires a small pressure drop in the line. This is fixed and quoted
in subsequent table. The design is suitable for gas when upstream pressure is reasonably
constant and downstream is variable, eg filling a buffer tank.
* See page 55 for specification details
54
www.mess-regeltechnik.at
AUTOMATIC FLOW CONTROLLERS
Flow Control Valves 10, 25, 300, 1000 and 5000 (L/min)
FFCV 5000
• Various inlet/outlet connection
available for 25 L/min model
FFCV 1000
FFCV 0300
FFCV 0010
FFCV 0025
FLOWMETERS
The unique valve design maintains accurate gas flows when supply pressure remains
constant but where downstream pressure can fluctuate.
FFCV 0025
Design Details
Dimensions mm
Weight kg
50 x 30 x 30
0.7
38 Diameter
0.45
60 Diameter
0.75
80 Diameter
1.0
120 Diameter
2.0
0.5 to 10
0.5 to 25
25 to 300
75 to 1000
250 to 5000
±1%
±3%
Aluminium Alloy
Nitrile
Brass, St Steel
Acetal Resin
1/8" BSPP
-10ºC to +50ºC
14
±1%
±3%
Aluminium Alloy
Nitrile
Brass, St Steel
Acetal Resin
1/4" BSPP
-10ºC to +50ºC
14
±1%
±3%
Aluminium Alloy
Nitrile
Brass, St Steel
Acetal Resin
1/2" BSPP
-10ºC to +50ºC
14
±1%
±3%
Aluminium Alloy
Nitrile
Brass, St Steel
Acetal Resin
1" BSPP
-10ºC to +50ºC
14
FFCV0025
FFCV0300
FFCV1000
FFCV5000
Specification
Flow Range
Air@ATP (L/min)
For 14 Bar Supply
Repeatability
Accuracy
Body Material
Diaphragm & Seals
Internal Parts
±1%
±3%
Brass
Nitrile
Brass, St Steel
Acetal Resin
Process Connections 1/8" BSPP
Temp Range
-10ºC to +50ºC
Pressure Bar G Max 14
Product Codes
Codes
FFCV0010
☎
+43 1 706 43 000
55
INDICATORS
FLOWMETERS
Paddle Wheel
Ball
This model can be mounted in any
orientation and operates over a wide
flow range. Suitable for clear or
cloudy liquids.
A mechanical flow indicator for gases
or liquids where the ball is lifted from
the valve seat by the fluid flow. The
bouncing ball under the glass dome
gives an immediate moving indication
of flow. Horizontal pipe lines only.
• High visibility spinner
• Ideal for flow indication in full pipes
• Mounted in any pipe position
• High quality, robust design
• High pressure option up to 60 bar
• Clear indication that flow is present
• High temperature / pressure capability
• Excellent chemical compatability
• Suitable for use on condensate, liquids
and gases
• Unrivalled flow and pressure drop
performance
Specification
Connections
Screwed: BSPP Female
Flanged: ANSI 150
Wetted Materials Stainless Steel or Gunmetal,
Toughened soda lime glass,
PTFE, Klingersil C4400
Pressure
16 bar max
Temperature
Stainless Steel: 250°C max
Gunmetal: 100°C max
Paddle Material Stainless Steel: Glass filled PTFE
Gunmetal: POM (Hostaform)
Specification
Body
Sight Ball
O-Ring Seals
Gasket
Dome
Pressure
Temperature
316 Stainless Steel
PTFE
Viton
Klingersil C4400
Borosilicate Glass
16 bar max
200°C max
Product Codes
Size Screwed
1/2"
3/4"
1"
11⁄2"
Flanged
2"
3"
4"
6"
Flow (L/min)*
3.5 to 25
4 to 40
7 to 60
17 to 160
SS
FSI15S
FSI20S
FSI25S
FSI40S
25 to 240
60 to 600
100 to 950
250 to 2200
FFSI0004
FFSI0005
FFSI0006
FFSI0007
Gunmetal
FSI15B
FSI25B
FSI20B
* Operating range (Gunmetal models work down to 75% of
min. flow stated above)
56
Air flow rates are typically 15 to 30 times those
specified for water, dependent upon line pressure
Product Codes
Connections
BSP
1/4"
3/8"
1/2"
3/4"
1"
1 1⁄2"
Min Water
Flow (L/min)
0.3
0.3
0.3
2.5
4.0
11.0
www.mess-regeltechnik.at
Code
FBFI8
FBFI10
FBFI15
FBFI20
FBFI25
FBFI40
Flap
Plain
This style is particularly suited to full
bore flows, giving an indication of
flow rate against a unit scale. Suitable
for horizontal or vertically upward
flow.
Suitable for viewing flow conditions in
applications with intermittent flow,
entrained air and partially filled pipes.
A special version for use with steam
and condensate uses Borosilicate Glass
to ensure good long-term visibility.
• Stainless Steel flap and scaleplate
• Provides a visual indication of flow
conditions within piping
• Ideal for flow monitoring in full
pipes
• High quality, robust design
• Allows visual inspection of pipe
contents
• Integral drip spout, ideal for leak
detection
FLOWMETERS
INDICATORS
• Suitable for mounting in any pipe
position
• Steam and condensation option
available
• High quality, robust design
Specification
Specification
Connections
Connections
Wetted Materials
Pressure
Temperature
Screwed: BSPP Female
Flanged: ANSI 150
Stainless Steel or Gunmetal,
Toughened soda lime glass,
PTFE, Klingersil C4400
16 bar max
Stainless Steel: 250°C max
Gunmetal: 200 °C max
Product Codes
Screwed: BSPP Female
Flanged: ANSI 150
Wetted Materials Stainless Steel or Gunmetal,
Toughened soda lime glass,
PTFE, Klingersil C4400
Pressure
16 bar max
Temperature
Stainless Steel: 250°C max
Gunmetal: 200°C max
Product Codes
Screw Size
1/2"
3/4"
1"
11⁄2"
Flow (L/min)*
20
20
30
55
SS
FFI15S
FFI20S
FFI25S
FFI40S
Flange Size
2"
3"
4"
6"
70
230
400
-
FFSI0000
FFSI0001
FFSI0002
FFSI0003
Gunmetal
FFI15B
FFI20B
FFI25B
Screw Size
1/2"
3/4"
1"
11⁄2"
SS
FPI15S
FPI20S
FPI25S
FPI40S
Gunmetal
FFSI0012
FFSI0013
FFSI0014
n/a
Flange Size
2”
3”
4”
6”
SS
FFSI0008
FFSI0009
FFSI0010
FFSI0011
With Borosilicate Glass (max pressure 8 bar)
Screw Size Gunmetal
1/2"
FPI15B
3/4"
FPI20B
1"
FPI25B
* Approximate FSD for water in horizontal pipes (not
specified for 6" version)
☎
+43 1 706 43 000
57
PRE-SET FLOW SWITCH
Liquid low flow switch for alarm duty on 1/2" or 3/4" pipe. Install with flow vertically
upwards. Contacts made for high flow, i.e. normal conditions.
SWITCHES
• Low cost flow alarm
• Simple rugged construction
• Brass, BSPP connections
• Selectable alarm trip level (factory set)
• Stainless Steel and other special OEM
versions available
Data Sheet DS1431
Specification
Body
Connections
Flow Sensor
Output
Wires
Rating
Pressure
Temperature
Length
FLFB Brass CZ121
FLFS Stainless Steel
1/2" or 3/4" BSP Female
FLFB - Brass with encapsulated magnet
FLFS - Stainless Steel with encapsulated magnet
SPST reed switch - open circuit for low flow
300mm long
Max 300V, 500mA, 10W
70 bar max
100°C max
1/2" BSP model: 90mm
3/4" BSP model: 100mm
Product Codes
Pipe Size
Brass Models
1/2" BSPP
1/2" BSPP
1/2" BSPP
1/2" BSPP
1/2" BSPP
3/4" BSPP
3/4" BSPP
3/4" BSPP
3/4" BSPP
58
Flow Range
(L/min)
Code
0.3
0.5
1.0
2.5
3.5
1.0
2.5
5.0
10
FLFB14L
FLFB11L
FLFB12L
FLFB13L
FLFB15L
FLFB22L
FLFB23L
FLFB24L
FLFB25L
Pipe Size
SS Models
1/2" BSPP
1/2" BSPP
1/2" BSPP
1/2" BSPP
1/2" BSPP
Flow Range
(L/min)
Code
0.3
0.5
1.0
2.5
3.5
FLFS14L
FLFS11L
FLFS12L
FLFS13L
FLFS15L
www.mess-regeltechnik.at
ADJUSTABLE (LIQUID) FLOW SWITCH
Using a spring loaded variable orifice flow meter technique, the sensor can be
installed at any angle and can operate at high pressures and temperatures. The
moving element trips an external reed sensor, which itself can be adjusted along a
flow scale.
SWITCHES
• Compact
• Good repeatability
• Dirt resistant
• High switch capability
• Hermetic separation of mechanical and
electrical components
Specification
Pipe Connections
Flow Range
Body
Seals
Pressure
Temperature
Cable
Output
Pressure Drop
Length
1/4" - 1" BSP
0.4 - 40 L/min
Ml Models - Brass; Kl Models - Stainless Steel
Ml Models - Buna N; Kl Models - Viton
200 bar max
120°C max
2.5m long IP65 termination
SPC0 250Vac VA 1.5 Amps
0.5 bar at max flow
MR8-20 109mm
MR25 135mm
Product Codes
Pipe Connections
BSP
Flow Switch Adjustment
(L/min)
Max Flow
(L/min)
Code
1/4" Brass
3/8" Brass
1/2" Brass
3/4" Brass
1” Brass
0.4 - 4
0.4 - 4
1 - 10
5 - 20
10 - 40
15
20
40
60
80
FMR8MI
FMR10MI
FMR15MI
FMR20MI
FMR25MI
1/4" SS
3/8" SS
1/2" SS
3/4" SS
1” SS
0.4 - 4
0.4 - 4
1 - 10
5 - 20
10 - 40
15
20
40
60
80
FMR8KI
FMR10KI
FMR15KI
FMR20KI
FMR25KI
☎
+43 1 706 43 000
59
PADDLE (LIQUID) FLOW SWITCH
SWITCHES
The body of the flowswitch is a standard pipe
tee, BSP threaded, which contains a paddle type
vane. Flow pushes the vane against magnetic
forces: when flow exceeds a critical value the
magnet actuates a reed switch. By coarse
adjustment of the reed switch position, the
output is changed between N/O & N/C
contacts: fine adjustment changes the flow
sensitivity and switch rate.
• Good repeatability
• Low pressure loss
• Dirt resistant
• Hermetic separation of electrical and
hydraulic components
• Stress free fixing of switch unit by
plastic cap
Specification
Pipe Sizes
Hysteresis
Connection
Limits
Material
Cable Length
Output
Protection
1/4" - 2"
0.7 L/min - depending on switch value
BSP Female
25 bar max, 110°C max
Brass or 316 Stainless Streel
1.5m
Reed contact, 1 Amp at 250V max. Selectable NO/NC SPST
IP65
Product Codes
60
Connections
BSP F
Flow Range
(L/min)
Max Flow
(L/min)
Brass Code
SS Code
1/4"
3/8"
1/2"
3/4"
1
11⁄4"
11⁄2"
2"
2.5 - 3
3 - 3.5
4.5 - 5
5-6
9.5 - 11.5
13 - 16
30 - 35
42 - 53
5
10
20
40
60
80
100
150
F59300105
F59300106
F59300107
F59300108
F59300116
F59300117
F59300118
F59300119
F59400105
F59400106
F59400107
F59400108
F59400116
F59400117
F59400118
F59400119
www.mess-regeltechnik.at
EXPLOSION PROOF FLOW SWITCH
SWITCHES
The Flotect is a paddle operated flow
switch for 1/2" to 2" pipelines. Magnetic
coupling between the spring loaded
vane and the microswitch gives a totally
glandless construction, suitable for
gases or liquid up to 2000psi. Models
are available with Stainless Steel or Brass
process parts.
• Leak proof lower body machined from
bar stock
• Weatherproof
• Low flow model offers field adjustable
set point
• Easy installation, simply insert the tee
in the pipeline and complete electrical
connections
• ATEX approved
Specification
Body
Vane
Mounting
Pressure
Temperature
Electrical Contact
Rating
Approval
Stainless Steel or Brass
Stainless Steel
Any plane
Brass 17 bar
Stainless Steel 138 bar
105°C max
SPDT switch
5 Amps at 125/250Vac
ATEX approval
Product Codes
Connections
NPT F
Low Flow Trip
Gas Flow (m3/hr)
Point (approx)
Liquid Flow (L/min)
Brass Code
(Tee Piece)
SS Code
(Tee Piece)
1/2"
3/4"
1"
11⁄4"
11⁄2"
2"
9
14
20
30
50
60
4
5
7
11
19
30
FFSV6S1BC
FFSV6S2BC
FFSV6S3BC
FFSV6S4BC
FFSV6S5BC
FFSV6S6BC
FFSV6S1SC
FFSV6S2SC
FFSV6S3SC
FFSV6S4SC
☎
+43 1 706 43 000
61
PADDLE FLOW SWITCHES
Adjustable Liquid Paddle Switch
SWITCHES
For liquid flow alarms at site adjustable
flow rates, these paddle flow switches
are simply mounted in a horizontal
flow line, through a 1" BSP
connection. The vane is selected or
cut to suit the pipe size.
Adjustable Plastic Paddle
(Liquid/Gas)
Made from chemical resistant and
durable polyphenylene sulphide, this
plastic paddle flow switch is suitable
for either liquid or air. When
flow stops the Stainless Steel
vane spring moves the vane
and activates a switch to
stop/start a pump, alarm or
open/close a valve. The
plastic vane is trimmable to
allow for installation on pipes
from 1" to 6".
• IP67 connection head (opt)
• Leak proof body
• Field trimmable vane
• Excellent chemical
• Suitable for 40mm
to 200mm pipe
Good
repeatability
•
• Low pressure loss
resistance
Data Sheet DS1401
Specification
Specification
Pipe Sizes
Paddle
Switch
IP Rating
Model VKB
Limits
Model VKS
Limits
Electrical Connection 3 x 460mm
18AWG wire
Temperature Limit 100°C max
Operating Pressure 10 bar
Pipe Connection
1" NPT
Switch
SPDT, 5 Amps at 125/250Vac
Body and Vane
Polyphenylene Sulphide (PPS),
Ceramic 8 magnet
Stainless Steel pin and spring
Installation
Install with index arrow in
direction of flow
1 ⁄2" - 8"
Stainless Steel
SPCO, 8A 250Vac
IP65
Brass body
11 bar, 120°C max
Stainless Steel body
30 bar, 120°C max
1
How to Specify
Site Adjustment (m3/hr)
Pipe
Minimum
Bore
Off-On
1
1 ⁄2"
1.1
1.7
2"
2.2
3.1
3"
4.3
6.2
4"
11
15
5"
23
28
6"
36
43
8"
73
85
Code
FVKB
FVKS
62
How to Specify
Maximium
Off-On
3.7
4.0
5.7
6.1
10.7
11.4
27
29
53
56
81
85
166
173
Approximate Actuation/De-actuation
Pipe
Water L/min (20°C)
Air m3/hr (ATP)
Size
Act.
De-act.
Act.
De-act.
1"
40.9
34.6
66.3
55.4
1
37.2
31.4
63.7
54.7
1 ⁄4"
32.4
25.7
56.7
45.4
11⁄2"
2"
41.2
33.4
73.1
62.5
3"
48.8
33.5
89.6
66
4"
79.7
52.5
148.9
108.1
6"
170.2
124.7
286.5
233.4
Code
FV8
FV8-IP67 (weatherproof version)
www.mess-regeltechnik.at
Air/Liquid Mini Flow Switch (V10)
Air/Liquid Mini Flow Switch (V11)
These simple paddle flow switches
are used to monitor the presence or
absence of air or liquid flow. The
switch can be adjusted by the user
from Normally Open (NO) to
Normally Closed (NC) easily without
interrupting process flow.
The V11 flow switch takes the very
popular V10 design and adds rugged,
integral electrical wiring. the onepiece PBT switch housing snaps onto
the body and the wiring is epoxy
sealed making the switch weatherproof.
• Leak proof body
• Low cost
• Field selectable switch
SWITCHES
SWITCHES
operation NO/NC
• Field trimmable vane
Data Sheet DS1402
Specification
Elect.Connection
Temp Limit
Operating Pressure
Pipe Connection
Switch
Electrical Rating
Body
Vane
Installation
2 x 460mm 22 AWG wire
93°C Maximum
Brass body 69 bar SS body 138 bar
1/2" NPT
SPST reed switch
1.5A,24Vdc resistive,0.5A,125Vac
Brass or Stainless Steel,Ceramic 8
magnet
Stainless Steel
Install with index arrow in
direction of flow
How to Specify
Approximate Actuation/De-actuation (for V10 and V11)
Water L/min (20°C)
Pipe
NO
NC
Size
Act.
De-act.
Act.
De-act.
1/2"
9.8
8.7
9.8
9.5
3/4"
11.7
10.2
11.7
10.6
1"
18.2
17.0
18.2
16.7
11⁄4"
23.5
21.2
23.1
21.2
11⁄2"
31.0
29.1
31.0
29.1
2"
36.0
34.4
36.0
34.1
Air Nm /Hr (ATP)
Pipe
NO
Size
Act.
1/2"
17.5
3/4"
22.1
1 1⁄4"
32.6
11⁄4"
42.1
11⁄2"
56.8
2"
85.3
De-act.
15.0
19.7
29.9
37.7
53.0
82.2
Body Type
Brass
Stainless Steel
Code
FV10B
FV10S
• Weatherproof head
• Leak proof body
• Low cost
• Snap-on electrical housing allowing
service without process shutdown
• Trimmable vane for 1/2" to 2" pipe sizes
Specification
Electrical Connection
Temp Limit
Operating Pressure
Pipe Connection
Switch
Electrical Rating
Body
Vane
Installation
3
NC
Act.
17.3
21.9
32.1
41.6
56.1
85.3
De-act.
15.6
19.7
29.9
38.2
52.0
81.1
☎
1 x 1.8m 22 AWG
121°C max
Brass body 69 bar
SS body 138 bar
1/2" NPT
SPST reed switch
1.5A, 24Vdc resistive, 0.5A,
125Vac
Brass or Stainless Steel
Ceramic 8 magnet
Stainless Steel
Install with index arrow in
direction of flow
Product Codes
Type
Brass Normally Open
Brass Normally Closed
Stainless Steel Normally Open
Stainless Steel Normally Closed
+43 1 706 43 000
Code
FV11B-NO
FV11B-NC
FV11S-NO
FV11S-NC
63
EXPLOSION PROOF ADJUSTABLE FLOW SWITCH
SWITCHES
For pipelines from 1 1/2" to 20", this paddle operated flow
switch uses magnetic coupling to transmit the vane
movement across a solid metal diaphragm to the electrical
switch output. Suitable for general purpose use. They are
supplied with a multi-layer vane suitable for all pipe sizes, on
liquids or gases. Normal mounting is vertical, via a 11/2" NPT
Threadolet welded to the horizontal pipeline.
• Leak proof body machined from bar stock
• Installs directly and easily into pipeline
with a threadolet, tee or flange
• Vertical options available
• High pressure rating of 1000 psig (69 bar)
with the brass body and 2000 psig (138
bar) with 316 Stainless Steel body
• Rugged construction
• Multi-layer universal vane
• ATEX approved
Specification
Stainless Steel or Brass, 1 1/2" NPT fitting
316 Stainless Steel
Vertical ±5° to horizontal pipe
Brass 69 bar
Stainless Steel 138 bar
135°C max
SPDT reed switch
10 Amps at 125/250Vac
ATEX approval
Body
Vane
Mounting
Pressure
Temperature
Electrical Contact
Rating
Approval
Product Codes
Body
Type
Brass
Stainless Steel
General
Purpose
FFSV4B
FFSV4S
Alarm and Reset Flow Rate
Pipe Diameter
Water Flow
(m3/hr)
1
1 ⁄2"
0.7 - 1.6
2"
0.9 - 3.4
3"
1.6 - 10
64
Explosion
Proof
FFSV4BC
FFSV4SC
Air Flow
(Nm3/hr)
29 - 72
22 - 108
72 - 360
Pipe Diameter
4"
6"
8"
10"
12"
14"
16"
18"
20"
Water Flow
m3/hr
2.7 - 22
6.8 - 48
15 - 85
23 - 136
32 - 204
45 - 273
57 - 318
74 - 454
91 - 545
www.mess-regeltechnik.at
Air Flow
Nm3/hr
72 - 684
180 - 1620
432 - 2628
900 - 3960
1350 - 5760
2100 - 7920
2700 - 10800
4000 - 13680
4700 - 16920
Plastic Float
Horizontal Stainless Steel
Float operated liquid level alarm
switches in glass filled polypropylene.
LS1 units can be installed from outside
the tank - a special sealing grommet
gives a water tight seal for up to 70 psi.
For liquid level control using a side
mounted Stainless Steel float switch. A
magnet in the float activates a reed
switch.
• Suitable for use on many fluids,acids,
oils
• Water Council approved for
drinking water applications
• Reversible float gives N/C or N/O
reed switch action
• Universal mounting kit allows
simple fitting from outside tanks
• Compact units for use in small
tanks
FRS1
Specification
FVS1
Specification
Contact Rating
Lead Length
Diameter Float
Mounting Hole
Container Wall
Fittings
Glass filled Polypropylene
Silicone rubber (LS1 only)
110°C max, 5 bar max
0.70 min
SPST: NO/NC choice by float
reversal. Resistive loads only
1 Amps 15 watts 250Vac/100Vdc
0.5m 2 cores
22mm
23mm if installed from outside,
16.5mm if installed from inside
4mm max
1/4" NPT M (RS1, VS1)
Product Codes
Description
Horizontal unit
Vertical unit
Right angle unit
FSRS
FSLS
FLS1
Material
Grommet
Limits
Liquid SG
Reed Contacts
• All Stainless Steel
• High temperature up to 120°C
• Compact design
• Optional DIN plug for SLS version
• N/O or N/C
SWITCHES
LEVEL SWITCHES
Material
Stainless Steel
Switch Rating
SPST 5A 240Vac 50VA
Temperature
-40°C to +120°C
MODEL SRS: Right angle stem fitting
10 bar max
Pressure
Liquid SG
0.75 min
Mounting
1/8" BSPP from inside tank
Leads
30cm, 2 cores
Float
Ø 28mm
Switch Level
50mm above/below hole
MODEL SLS: Horizontal cylindrical float
5 bar max
Pressure
Liquid SG
0.7 min
Float
Ø 17mm
Insertion Length 92mm
Mounting
1/2" BSPT from outside the tank
Connections
30cm flying lead or DIN IP65 plug
Product Codes
Description
Right angle stem
Horizontal Cylindrical Float
1/2" BSPT, flying leads
1/2" BSPT, DIN IP65 plug
Code
FLS1
FVS1
FRS1
Code
FSRS22
FSLS12
FSLS12P
Other model options available on request
☎
+43 1 706 43 000
65
LEVEL SWITCHES
SWITCHES
66
Vertical Stainless Steel
Peardrop
For liquid level control and tank level
alarm using all Stainless Steel wetted
parts. A magnet in the float activates a
reed switch to give an electrical contact closure.
The float contains a tilt switch and is
suspended into the tank or sump
from above on the cable. Above the
float a weight holds the cable vertical;
when the liquid causes the float to rise
it switches an SPDT microswitch to
trigger an alarm or pump.
• Storage tank high level alarms
• Pump control
• Machinery protection
• Adjustable counter weight
position to select the level
differential
• Blow moulded moplen
outer casing, chemical
resistant and shock-proof
• Lead spheric actuator of
the electrical switch to
avoid oxidation and blocks
by signalling lack
of coolant or lubricant
• Ideal for small tanks
where space is
limited
• Model RFS: for
use in hot oil
tanks, fat fryers
Specification
Specification
Materials
316 Stainless Steel
Switch Rating
SPST 5A 240Vac 50VA
Leads
30cm 2 core
MODELS SVS
10 bar max
Pressure
Temperature
-40°C to +120°C
Liquid SG
0.75 min
Mounting
1/8" BSPP from inside tank
Float
Ø 28mm
MODEL RFS: High temperature version
Pressure
10 bar max
Temperature
200°C max
Liquid SG
0.53 min
Mounting
3/8" BSPP
Float
Ø 50mm
Insertion Length 75mm
Float
Cable
Cable Length
Rating
Output
Temperature
Ballast Weight
Product Codes
Product Codes
Description
Code
Vertical mounting
FSVS22
Vertical mounting, high temperature FRFS62
Float Switch with:
5m cable
10m cable
25m cable
Polypropylene homopolymer
Thick PEC double insulated
5m, 10m or 25m
IP67 (to 50 metres)
1 Amps 15 watts 250Vac/100Vdc
60°C max
200gm Polyurethane (Note: this
should be positioned typically
0.5m from float)
NB It is recommended that this float should
be used with a relay module (p69) to switch
AC power circuits.
www.mess-regeltechnik.at
Model
FEC5
FEC10
FEC25
CAPACITANCE LEVEL TRANSMITTER
Probe with concentric metallic tube with inner tube
insulated, for use with conducting
liquids such as aqueous solutions. Standard
material stainless steel, sheathed with
polypropylene. Other insulation options are
available.
FCP4
Probe with concentric metallic tube electrode
for non-conducting liquids such as oils etc
generally with low dielectric constant.
Standard material is stainless steel.
LEVEL
FCP3
• Continuous monitoring
• Robust and reliable
• Plastic or insulated tank
• Metal or reinforced concrete tank
• Cost effective
• Simple to install
• No dead band
• Rigid probes up to 3m long
Specification
Insertion Length
Process Connection
Process Temperature
Ambient Temperature
Process Pressure
Termination Head
Electrical Connection
Connection Cable
Electrode Material
Electrode Insulation
Rigid up to 3m
1" BSP
100ºC max
-20ºC to 60ºC
300psi @ 20ºC
Polypropylene as standard
Screw Terminals
Screened
Type 316 SS (other materials to special order)
Polypropylene (other materials to special order)
Product Codes
FCP3/4-20/1m
FCP4/4-20/1m
Other probe lengths available on request
☎
+43 1 706 43 000
67
ULTRASONIC LEVEL TRANSMITTER
The Ultrasonic Level Transmitter provides accurate, reliable level measurement for
liquids and slurries. It is a loop powered, ultrasonic transmitter which operates from
a 20 - 38Vdc supply, thus enabling the 4-20mA signal produced to be transmitted
over relatively long distances.
• Simple setting up procedure,
LEVEL
save commissioning time
• Low power consumption gives
economical operation
• Self-diagnosis facility and automatic
re-calibration
• Polypropylene casing for increased
chemical resistance
• Weatherproof to IP68 (2m for 24 hours)
• The integral moulded flange accepts
ANSI, DIN, BS, sizes
Specification
Construction Materials
Mounting Bracket
Measuring Range
Output
Loop Voltage
Power Required
Resolution
Accuracy
Display
Minimum Span
Lost Echo
Temperature Compensation
Operating Temperature
Weatherproof
Gland Thread
Cable
Universal Flange
Ultrasonic Core Angle:
Max Static Operating Pressure
Casing: Polypropylene (glass filled), Transducer housing: UPVC
Swing type bracket
0.5 to 8m
4-20mA (into 250ohms @ 240Vdc or 850 ohms @ 38Vdc)
20-38Vdc (reverse polarity protected)
0.5 watts @ 24V
1mm
0.25% of measuring range (electronic)
4 digits
100mm
User programmable 4, 20, 21mA or last valid reading
Built it digital sensor
-10°C to +60°C
IP68 (immersion in water at 2m for 24 hrs)
M20
2 core screened cable or twisted pair
Suitable for ANSI 3" 150lb, DN 80 PN16, BS10 table D 3", type 81 bracket
12°
-0.25 to 2 bar @ 20°C
Options
• If 4 control relays, digital indication and a power supply are required use Flexilevel 2 as an add on unit
• If only 2 relays and a power supply are required use Type 800 Dual Trip Amp or the PS2 power supply with
cable monitoring and lost echo
How to Specify
Code: USLT1
Dual Trip Amp
PS2 power supply
Please contact our Technical Sales Team to discuss your application
68
www.mess-regeltechnik.at
LEVEL CONTROL
For site adjustable liquid level control
points on aqueous liquids, this four
electrode probe is mounted on the
tank top. Electrodes are cut to length
on site to define a) high or low level
alarm, b) pump “on” level, c) pump “off”
level, or similar functions, with the last
electrode left as the common or earth.
Electronic output is then made using
relay module RLM48T, with simple
electrical connections to the terminal
head.
Pump Control or Level Alarm
Module
Panel mounted interface between
simple liquid level sensors and
mains high current devices such as
pumps, klaxons or lamps. Sensors
can be any float switch or multipoint
electrode systems, which are driven
with a low voltage, safe sensing
current.
LEVEL
Level Control Electrodes
• Use with Electrodes or Level
Switches on pages 65 and 66
• Connections for two sensors for
pump control
• Tank level control for any
conducting liquid
• High level alarm
• Low level alarm
• Dual point
pump control
Specification
Supply Voltage
Temperature
Enclosure
Mounting
Connections
Output Relay
Alarm Function
Specification
Electrodes
Holder
Mounting Thread
Conduit Thread
Temperature
Sensing Circuit
1 metre long Ø 3.2mm
Stainless Steel, epoxy
coated-4 off supplied
Moulded Polypropylene
3/4" BSP (locknut provided)
M20
-20°C to +60°C
Front Panel LED
Time Delay
110/230Vac
-15°C to +45°C
48 x 48, 96mm deep
Front panel or supported by
base
Via 11 pin base plug in unit
240Vac 5 Amp
DPDT for level alarm, or SPDT
for pump control
Probe or float monitoring via
14Vac sensing circuit. Output
relay de-energises when
product is detected.
Indicates when relay energised
0 - 15 seconds adjustable to
prevent frequent alarms and
relay chatter from liquid
turbulence
Product Codes
Product Codes
Description
Electrode holder and
4 off 1m long probes
Description
Module with variable time delay option
Accessory
11pin mounting base
Code
FE14
Code
FRLM48T
FRLM11B
Other options available on request
☎
+43 1 706 43 000
69
PROPORTIONAL CONTROL VALVES
Platon M - Valves
VALVES
For use on gas, liquids or steam, the MValve is an air operated proportional
control valve for 1⁄4" or 1⁄2" lines. The
interchangeable plug and seat trims are
available with CV values from 3.0 down to
0.00007, with a control range of up to 40:1.
The standard actuator is available with
air-to-open or air-to-close action, using
3-15 psi. For high line pressures or for very
low flow control a pneumatic positioner
is recommended.
• Pilot plant control
• Dosing, blending or flavour flow control
• Cryogenic liquid control for cooling
• Hazardous area applications
• Bellows sealed units for dangerous
gases, nuclear applications.
Data Sheet DS1810
Specification
M-Valve
Body Material
Packing
Fluid Temperature
Pressure
Process Connections
316 Stainless Steel (Options - Carbon Steel, Monel, Hastelloy, PVC)
Braided PTFE (Options - Solid PTFE, Chevron, Bellow Seals)
-75 to 190°C (Option - Cryogenic to 400°C)
150 bar max (subject to valve packing)
1/4" or 1/2" NPT standard
Standard Pneumatic Actuator
Direct acting 3 -15 psi
Signal Input
Temperature
-20°C to 50°C Ambient
Variants
Air-to-Open or Air-to-Close
Housing
Die-cast aluminium
Diaphragm/Seals
Nitrile
Pneumatic Positioner
Moore Positioner built onto
Type
standard air motor
Air supply
Max 100 psi, min 5 psi above
required valve actuation
pressure
Signal Input
3-15 psi
Temperature
-20 to 50°C Ambient
Variants
Air-to-open or air-to-close
How to Specify
To specify and size the M Valve trim required, please specify:
•
•
•
•
•
70
Line size
Connections required
Valve materials
Upstream and downstream pressure
Air-to-Open or Air-to-Close
•
•
•
•
•
Linear or equal % trim
Fluid type, SG, viscosity, density
Temperature
Valve pressure drop
Max flow rate and flow range required
www.mess-regeltechnik.at
FCV FINE CONTROL VALVES
VALVES
A selection of fine control needle valves suitable
for gradual opening and closing of gas or liquid
flows. Suitable for use with all Platon Glass Tube VA
flowmeters, the standard FCV is rated at up to 25
bar line pressure. As with all control valves the FCV
is not designed for total leak free shut off.
• 1⁄4" BSPP Connection fits directly into pipework
• Fits in any orientation
• Choice of low, medium or high flow control
• Ideal for use with NGXI, LGXI and GU flowmeters
• Brass or Stainless Steel options
Specification
Valve Body
Valve Needle
Seals
Brass or Stainless Steel
316 Stainless Steel
Nitrile with Brass
Viton with Stainless Steel
1/4" BSPP Female thread
25 bar, higher to special order
80°C
Connections
Max Operating Pressure
Max Operating Temp
* CVA Adaptors available
for LGXI/NGXI and GU
series Flowmeters
Product Codes
Body Material
Brass
Brass
Brass
Stainless Steel
Stainless Steel
Stainless Steel
Flow Rate at ATP &
0.25 bar Air
0 - 10 L/min
0 - 45 L/min
0 - 100 L/min
0 - 10 L/min
0 - 45 L/min
0 - 100 L/min
☎
Order Code
Adaptor Type
Order Code
FFCVBL
FFCVBM
FFCVBH
FFCVSL
FFCVSM
FFCVSH
LGXI/NGXI Brass
LGXI/NGXI Stainless Steel
GU Brass
GU Stainless Steel
F5842112
F5842114
F5842122
F5842124
+43 1 706 43 000
71
NEEDLE VALVES
VALVES
T - Bar Valves
2, 3 & 5 Valve Manifolds
A range of fine control valves, suitable
for control of high pressure flow lines
up to 6000 psi. The non-rotating, self
centreing, anti-galling spindle tip gives
positive bubble tight shut-off, plus
good flow control.
A range of two, three and five valve
manifolds ideal for remote or direct
fitting to pressure gauges, switches
or transmitters. All units combine
isolating, calibration or re-calibration
facilities in one compact unit, with
clearly marked valves for ease of
identification and safe operation.
• Bubble tight metal to metal seat for
positive shut off
• Unique bonnet locking cam.
• Bubble tight shut off
• Metal to metal bonnet seal for high
No accidental removal of head unit,
or loosening due to vibration
• Bi-directional flow, with preferred
flow indicated
extend field life further
Specification
Specification
Valve Body
Spindle Seal
Connection/Threads
Valve Configuration
Operating Pressure
Temperature
Cv
Body
Process Connections
Valve Configuration
Working Pressure
Seals
Mounting Bolts
Temperature
Carbon Steel or 316 Stainless Steel
PTFE
BSP parallel or NPT thread
Female to female
Max 6000 psi
-20°C to 100°C
0.46 max (5.4mm orifice)
Product Codes
Body Type
Carbon steel
Carbon steel
Carbon steel
Carbon steel
Carbon steel
SS
SS
SS
SS
SS
72
pressure and high temperature use
• Repair / service kit available to
Pipe
Size
1/4"
3/8"
1/2"
3/4"
1"
1/4"
3/8"
1/2"
3/4"
1"
BSPP Thread
Code
F49410301
F49410302
F49410303
F49410304
F49410305
F49420301
F49420302
F49420303
F49420304
F49420305
316 Stainless Steel
1/2" NPT
Refer to product codes
Max 6000 psi
PTFE
M10 (3 and 5 valve only)
-20°C to 100°C
Product Codes
NPT Thread
Code
F49410306
F49410307
F49410308
F49410309
F49410310
F49420306
F49420307
F49420308
F49420309
F49420310
Type
2 Valve
2 Valve
3 Valve
5 Valve
•
•
Valve Configuration
Female x Female
Female x Male
Female x Female
Female x Female
Code
FVVA0080
FVVA0081
F49430300
F49430301
Please specify mounting option required
For BSP process connections, consult our Technical
Sales Team for details
www.mess-regeltechnik.at
2 Way Direct Acting
3 Way Direct Acting
A direct acting two way solenoid
valve with options for normally open
(B) or normally closed (A) for on/off
control of non-aggressive fluids and
gases such as air, oil or water.
A three way direct acting solenoid
valve for on/off control of nonaggressive fluids and gases such as air,
oil or water. Model 80C has normally
closed switching and is supplied
complete with exhaust port.
VALVES
SOLENOID VALVES
Specification
Ambient Temp
Fluid Temp
Viscosity
Body
Seals
Coil Voltage
Voltage Tolerance
Power Consumption
Duty Cycle
Protection
Response Time
-20°C to 55°C
-10°C to 90°C
Max 37 cSt, 5°E
Brass with Stainless Steel
tube and tube nut
NBR Buna
12V and 24Vdc, 24V,
110V and 230Vac
±10% (+10% -5% on pure DC)
8 Watts AC/DC
100% continuous rating
IP65
10 to 30ms
Product Codes
Size
BSPP
Orifice
Size
Pressure
Range
(bar)
1/8"
1/8"
1/8"
1/8"
1/8"
1/4"
1/4"
1/4"
1/4"
1/4"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
1/2"
1/2"
1/2"
1/2"
2.5mm
2.5mm
2.5mm
2.5mm
2.5mm
2.5mm
2.5mm
2.5mm
2.5mm
2.5mm
4.5mm
4.5mm
4.5mm
4.5mm
4.5mm
4.5mm
4.5mm
4.5mm
4.5mm
4.5mm
13
13
20
20
20
13
13
20
20
20
0.9
0.9
4.5
4.5
4.5
0.9
0.9
4.5
4.5
4.5
Coil
Code*
12Vdc
24Vdc
24Vac
110Vac
230Vac
12Vdc
24Vdc
24Vac
110Vac
230Vac
12Vdc
24Vdc
24Vac
110Vac
230Vac
12Vdc
24Vdc
24Vac
110Vac
230Vac
F594201234*
F594201235*
F594201236*
F594201237*
F594201238*
F594201239*
F594201240*
F594201241*
F594201242*
F594201243*
F594201244*
F594201245*
F594201246*
F594201247*
F594201248*
F594201249*
F594201250*
F594201251*
F594201252*
F594201253*
* Add suffix A for normally closed or B for normally open
☎
Specification
Ambient Temp
Fluid Temp
Viscosity
Body
Seals
Coil Voltage
Voltage Tolerance
Power Consumption
Duty Cycle
Protection
Response Time
-20°C to 55°C
-10°C to 120°C
Max 37 cSt, 5°E
Brass with Stainless Steel
inner port
Viton
12V and 24Vdc, 24V,
110V and 230Vac
± 10% (+10% -5% on pure DC)
8 Watts AC/DC
100% continuous rating
IP65
10 to 30ms
Product Codes
Port Size
BSPP
1/8"
1/8"
1/8"
1/8"
1/8"
1/4"
1/4"
1/4"
1/4"
1/4"
Pressure
Range (bar)
10
10
10
10
10
10
10
10
10
10
+43 1 706 43 000
Coil
Code
12Vdc
24Vdc
24Vac
110Vac
230Vac
12Vdc
24Vdc
24Vac
110Vac
230Vac
F5954201250
F5954201251
F5954201252
F5954201253
F5954201254
F5954201255
F5954201256
F5954201257
F5954201258
F5954201259
73
SOLENOID VALVES
Servo-Acting
VALVES
A servo-acting solenoid valve for
on/off control of non-aggressive
fluid, such as air, oil or water. Available
as normally closed switching, this
valve requires a minimum pressure
drop of 0.2 bar for satisfactory
operation ie. backpressure on the
downstream port.
Specification
Ambient Temp
Fluid Temp
Viscosity
Body
-20°C to 55°C
-10°C to 90°C
Max 21 cSt, 3°E
Brass with Stainless Steel
and Brass internal parts
Seals
NBR Buna
Coil Voltage
12V and 24Vdc, 24V,
110V and 230 Vac
Voltage Tolerance
± 10%
Power Consumption AC: 28VA impulse,13VA hold
DC: 8W
Duty Cycle
100% continuous rating
Protection
IP65
74
Orifice
Size
12mm
12mm
12mm
12mm
12mm
19mm
19mm
19mm
19mm
19mm
25mm
25mm
25mm
25mm
25mm
40mm
40mm
40mm
40mm
40mm
Pressure
Range
(bar)
0.2 - 20
0.2 - 20
0.2 - 20
0.2 - 20
0.2 - 20
0.2 - 16
0.2 - 16
0.2 - 16
0.2 - 16
0.2 - 16
0.2 - 16
0.2 - 16
0.2 - 16
0.2 - 16
0.2 - 16
0.2 - 10
0.2 - 10
0.2 - 10
0.2 - 10
0.2 - 10
Similar in design to servo-acting
model. This normally closed valve is
able to operate at zero pressure and
without a differential. This is achieved
by mechanically coupling the plunger
to the diaphragm, overcoming the
problems associated with
gravity feed and circulating
systems.
Suitable for nonaggressive fluids
and gases.
Specification
Ambient Temp
Fluid Temp
Viscosity
Body
Seals
Coil Voltage
Voltage Tolerance
Power Consumption
Product Codes
Port
Size
BSPP
3/8"
3/8"
3/8"
3/8"
3/8"
3/4"
3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"
1"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
1 1/2"
Servo-Acting Coupled
Diaphragm
Duty Cycle
Protection
Coil
Code
12Vdc
24Vdc
24Vac
110Vac
230Vac
12Vdc
24Vdc
24Vac
110Vac
230Vac
12Vdc
24Vdc
24Vac
110Vac
230Vac
12Vdc
24Vdc
24Vac
110Vac
230Vac
F5954201260
F5954201261
F5954201262
F5954201263
F5954201264
F5954201265
F5954201266
F5954201267
F5954201268
F5954201269
F5954201270
F5954201271
F5954201272
F5954201273
F5954201274
F5954201275
F5954201276
F5954201277
F5954201278
F5954201279
-20°C to 55°C
-10°C to 90°C
Max 21 cSt, 3°E
Brass
NBR Buna
12V and 24Vdc, 24V,
110V and 230Vac
±10%
3/8" and 1/2" : 8 Watts
3/4" & 1" : 14 Watts
100% continuous rating
IP65
Product Codes
Port
Size
BSPP
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
1/2"
3/4"
3/4"
3/4"
3/4"
1"
1"
1"
1"
Orifice
Size
12mm
12mm
12mm
12mm
12mm
12mm
12mm
12mm
19mm
19mm
19mm
19mm
25mm
25mm
25mm
25mm
Pressure
Range
(bar)
0-7
0 - 14
0 - 14
0 - 14
0-7
0 - 14
0 - 14
0 - 14
0 - 14
0 - 14
0 - 14
0 - 14
0 - 14
0 - 14
0 - 14
0 - 14
Coil
Code
24Vdc
24Vac
110Vac
230Vac
24Vdc
24Vac
110Vac
230Vac
24Vac
24Vdc
110Vac
230Vac
24Vdc
24Vac
110Vac
230Vac
F5954201280
F5954201281
F5954201282
F5954201283
F5954201284
F5954201285
F5954201286
F5954201287
F5954201288
F5954201289
F5954201290
F5954201291
F5954201292
F5954201293
F5954201294
F5954201295
www.mess-regeltechnik.at
Sizing for Liquids
Liquid Density Correction
For Volumetric Flow At Standard Reference
Liquid
density
(g/cm3)
For Volumetric
units (e.g.
l/min) multiply
scale reading of
water flow rate
(in same units)
by factor:
For Gravimetric
units (e.g. g/min)
multiply scale
reading of water
flow rate (in
same units) by
factor:
0.60
0.65
0.70
0.75
0.80
0.85
0.90
0.95
1.00
1.05
1.10
1.15
1.20
1.25
1.30
1.35
1.40
1.45
1.50
1.55
1.60
1.65
1.70
1.75
1.80
1.85
1.90
1.95
2.00
1.328
1.271
1.221
1.175
1.134
1.096
1.062
1.030
1.000
0.972
0.947
0.922
0.900
0.878
0.858
0.839
0.821
0.803
0.787
0.771
0.756
0.741
0.727
0.714
0.701
0.689
0.677
0.665
0.654
0.797
0.826
0.855
0.881
0.907
0.932
0.955
0.978
1.000
1.021
1.041
1.061
1.080
1.098
1.115
1.132
1.149
1.165
1.180
1.195
1.209
1.223
1.237
1.250
1.262
1.274
1.286
1.298
1.309
Condition Of 20°C
Definition of Sizing Factor (K)
Water equivalent flowrate:
Q1 = Sizing Factor (K) x max Liquid Flow Q2
i.e. Q1 = K x Q2
Max Flow liquid Q2 = Q1 (water equiv. flow)
Sizing Factor (K)
Sizing Factor(K) =
6.96 x X2
7.96 - X2
Where X2 = Liquid density at working conditions (g/cm3)
Example 1
To establish water equivalent flowrate and tube float
combination for:
1.5 l/min paraffin, working density 0.80 g/cm3
Sizing factor (K) =
6.96 x 0.80 = 0.882
7.96 - 0.80
Water equivalent Q1 = 0.882 x 1.5 = 1.323 l/min
Nearest standard range = 200 to 1500 cm3/min
using GTF 2ASS Tube & Float
TECHNICAL
VA FLOWMETER SIZING DATA
Equivalent paraffin flowrate =
200 (min)
0.882
to
1500 (max)
0.882
i.e 227 to 1700 cm3/min paraffin
Select meter type from VA Flowmeter section of
catalogue.
The flowmeter can then be supplied calibrated
for: 0.2 to 1.7 L/min of paraffin.
To select the correct size VA flowmeter for a specific application (liquid or gas) it is necessary to convert the
required flow to an equivalent air or water flowrate. The nearest standard range flowmeter can then be
selected using the table shown on page 11.
☎
+43 1 706 43 000
75
VA FLOWMETER SIZING DATA
Sizing for Gases
Gas Density Corrections
For Volumetric Flow At Standard Reference
TECHNICAL
Conditions Of 20°C And 1.013 bar abs. (ATP)
Definition of Sizing Factor (K):
Air equivalent flowrate
(F1) = Sizing factor (K) x Max gas flow (F2)
Note: F2 MUST BE EXPRESSED IN FREE
Flowmeter scales can be infinite in variety due to the
differing physical properties of gases and their operating
conditions. Standard tubes for gases are calibrated for
atmospheric pressure at the flowmeter outlet. If the
working outlet pressure (P) is different, the scale reading
(expressed at ATP) should be corrected by using the formulae:Actual flow
rate (@ATP) =
Sizing factor (K) =
Actual flow rate
(@ working
pressure P) =
r x T2 x 1.013
P2
293
P (Bar Abs.) x Scale reading
1.013
VOLUMES OF GAS (ie. MEASURED AT ATP)
Where:
1.013
r = Relative density of Gas to be measured
P2 = Absolute Operating Pressure (bar)
T2 = Gas Temperature (Kelvin)
Notes:
1. Density and pressure correction factors should not
be applied to the lowest flowrate tubes (Frame Size 1) consult RM&C sales.
Example 2
2.
To establish equivalent air flowrate and suitable
tube and float combination for 15 l/min acetylene
(free volume measured at ATP) working at 5 barg
and 40°C.
To convert ATP air flow rates to ATP flow rates of the selected
gas, divide by sizing factor K:
Tubes with scales for different operating pressures
and calibration conditions are available to order.
Gas
P2 = 1.013 + 5 = 6.013 bar Abs,
T2 = 273 + 40 = 313 K,
Chemical
Formula
Relative
Density
(Air = 1)
Sizing
Factor
K
C2H2
NH3
A
C4H10
CO2
CO
Cl2
C3H6
C2H6
C2H4
He
H2
HCl
H2S
CH4
Ne
N2
N2O
O2
C3H8
SO2
0.898
0.588
1.380
2.007
1.520
0.967
2.450
1.453
1.038
0.968
0.138
0.0695
1.259
1.177
0.554
0.697
0.968
1.520
1.105
1.522
2.210
0.948
0.767
1.175
1.417
1.233
0.983
1.565
1.205
1.019
0.984
0.371
0.264
1.122
1.085
0.744
0.835
0.984
1.233
1.051
1.234
1.487
r = 0.898 (from reference table)
Sizing Factor (k) = 0.898 x 313 x 1.013 = 0.402
6.013
293
Equivalent Air Flow: F1 = 15 x 0.402 = 6.03 l/min
Nearest standard range = 1 to 10 l/min Air
tube for G Series
Flowmeter, GTF 2BHS Tube & Float.
Equivalent Acetylene Flowrate = 1(min) to 10(max)
0.402
0.402
ie. 2.29 to 24.88 l/min Acetylene @ 5barg
Select meter type from VA Flowmeter section of
catalogue.
The flowmeter can then be supplied calibrated for:
25 L/min of acetylene at 40°C and 5 bar G.
Notes:
76
x Scale reading
P (Bar Abs.)
Acetylene
Ammonia
Argon
Butane
Carbon Dioxide
Carbon Monoxide
Chlorine
Cyclopropane
Ethane
Ethylene
Helium
Hydrogen
Hydrogen Chloride
Hydrogen Sulphide
Methane
Neon
Nitrogen
Nitrous Oxide
Oxygen
Propane
Sulphur Dioxide
1. RM&C expresses gas volumes at ATP (1.013 bar abs x 20ºC)
2. Standard density of air @ ATP = 1.204 g/L
www.mess-regeltechnik.at
UNIT CONVERSIONS & IP TABLE
To convert
flows of
into
multiply
by
Reciprocal
To convert
into
multiply
by
Reciprocal
Imp. Gal/hr
l/min
0.07577
13.20
Imp. Gallons
Litres
4.5460
0.21997
U.S. Gal/hr
l/min
0.06308
15.85
U.S. Gallons
Litres
3.7854
0.26417
Cu. Ft/hr
l/min
0.4719
2.119
Imp. Pint
Litres
0.56826
1.7598
ml/min
9.471
0.1056
Cubic feet
Litres
28.316
0.035315
1.000027
Imp. Pint/hr
m3/hr
0.1637
6.110
Cubic Centimetre
Millilitres
0.999973
Imp. Fluid Oz/hr
ml/min
0.4735
2.112
Cubic Inch
Millilitres
16.387
0.061024
Pounds/hr
g/min
7.560
0.1323
Imp. fluid ounce
Millilitres
28.413
0.035195
Imp. Gal/min
m3/hr
0.2728
3.666
Cubic Metre
Litres
1000
0.001
U.S. Gal/min
m3/hr
0.2271
4.403
Pound
Kilogrammes
0.45359
2.2046
Kilogrammes
0.028349
35.274
Tonne
1.01605
0.98421
To convert
into
Reciprocal
inch H2O
psi
inch Hg
KPa (KN/m2)
Atm
Kg/cm2
Kg/cm2
psi
psi
N/cm2
millibar
millibar
millibar
millibar
bar
bar
psi
Atm
inch H2O
KPa (KN/m2)
multiply
by
2.491
68.95
33.86
10
1.0132
0.9807
14.22
0.06805
27.68
10
Barrels/hr
Cu. Ft/min
m3/hr
1.699
0.5886
Ounce
Pounds/min
Kg/hr
27.22
0.03674
Imp. Ton
Litres/min
m3/hr
0.06
16.67
Litres/sec
m3/hr
3.6
0.278
Temperature
TECHNICAL
Mass & Volume
Flowrates
Pressure
ºC = (ºF - 32)
1.8
ºF = (1.8 x ºC) + 32
0ºC = 273.15K
0.4015
0.014504
0.02953
0.1
0.9869
1.0197
0.07031
14.696
0.03613
0.1
Ingress Protection (IP) codes - (IEC/EN 60529)
First Numeral
SOLID BODIES
No protection
Objects greater than 50mm
Objects greater than 12mm
Objects greater than 2.5mm
Objects greater than 1.0mm
Dust-protected
Dust-tight
0
1
2
3
4
5
6
0
1
2
3
4
5
6
7
8
Second Numeral
LIQUIDS
No protection
Vertically dripping water
Angled dripping water -75ºC to 90ºC
Sprayed water
Splashed water
Water jets
Heavy seas
Effects of immersion
Indefinite immersion
Example: IP65 equipment is dust-tight and protected against water jets
☎
+43 1 706 43 000
77
PRESSURE OVERVIEW
PRESSURE
RM&C Sensit
Leader in ceramic strain gauge
• World
technology since 1988
only UK company manufacturing
• The
ceramic pressure sensors
• A full range from low cost, ready to
use pressure capsules to fully packaged
pressure transducers and transmitters
Pressure Measurement
Sensit’s experienced R&D team have a broad range
of knowledge satisfying the requirements of many
different applications including:
Specification
OEM Inkjet Printers
Automotive Engine Test
Off Highway Vehicles
Hydraulic/Pneumatic Systems
Pulp/Paper Production
Waste Water
Sewage Treatment
Reservoir/River Level
Borehole Level
Tank Level/Marine
Train Braking
Oil Extraction
Cable Protection
Milking Systems
Medical Equipment
Meteorology
Oceanography
Product Codes
78
www.mess-regeltechnik.at
OEM Ceramic
Pressure Sensors
Industrial Pressure
Transmitters
• Chemical & corrosion resistance
to suit application - Ø15mm,
• Size
Ø19mm and Ø34mm
• Pressures: 0-100mbar to 0-1000bar
• Temperatures: -25°C to 130°C
• Gauge or Absolute pressure
• Span 1.0 to 5.0 mV/V
• Custom interconnection
• Accuracy 0.1% span
operating temperature
• Wide
range from -25°C to 125°C
• Robust - immune to shock
Electrical or process
• Custom
connections
safe versions
• Intrinsically
available
options: mA, mV
• Output
or voltage
• Pressures: 100mbar to 600 bar
OEM
Transducers
Submersible Pressure
Transmitters
• Applications Engineering Support
• Improve design - reduce costs
• Customer specific design
to interpret customers’
• Ability
requirements
solving - broad
• Problem
expertise
• Quick delivery prototypes
• Small diameter
• Chemical & corrosion resistance
• Output: 4-20mA or 10mV/V
• Pressures: 1 to 500mWG
• Temperatures: -10°C to 60°C
• Power supply: 2.5 to 32Vdc
• Lightning protection
Pulp & Paper Flush
Transmitter
Slurry
Transmitter
• Chemical & corrosion resistance
• Unrivalled abrasion resistance
400mbar to 50bar
• Pressures:
G or Abs
• Temperatures: -25°C to 100°C
• Output: mA, mV or voltage
• Stainless steel case
• Anti-clogging
• Robust mechanical design
• Unrivalled abrasion resistance
• Pressures:
5 to 100bar G or Abs
• Temperatures:
-25°C to 100°C
• Output:
mA, mV or voltage
• Stainless steel case
☎
+43 1 706 43 000
PRESSURE
PRESSURE OVERVIEW
79
TRANSMITTERS
TRANSMITTERS
mV Transducer
General Purpose
Economic OEM mV sensor designed
for installation inside industrial
equipment & machinery. Ideally suited
to battery powered equipment
operating from 2.5V & with 1mS
response time. The OEM transducer
combines Sensit’s high purity ceramic
pressure sensor technology with
passive signal conditioning to provide a
temperature compensated mV output.
2-wire, 4 to 20mA uncompensated
pressure transmitters based on a four
active arm strain gauge bridge, fused
to a high-purity alumina ceramic
diaphragm, offering high natural
output coupled with superb chemical
and corrosion resistance. This is
housed within a Stainless Steel case
and supplied with a plug and socket.
Data Sheet 2810
Specification
Data Sheet 2902
Specification
Output
NL, H & R
Thermal zero shift
Thermal span shift
Temp range
Long term stability:
2.5 to 4.5mv/V ratiometric
±0.15% span
<±0.015% span/ºC
<±0.015% span/ºC
0ºC to 80ºC
±0.25% span/year
80
Span ±30%
2.5 mV/V
4.0 mV/V
4.5 mV/V
1/4" BSP male (G 1/4)
0.5 to 600 bar gauge or Absolute
4 to 20mA, loop powered
10 to 30 Vdc
1KΩ @30V
<±0.25% of span
0 to 80oC
±0.08% of span/oC typical
±0.04%/oC typical
1.5 x rated range
Alumina ceramic, SS & Viton
IP65
DIN 40050 Micro-connector
* includes non-linearity, hysteresis & repeatability
Product Codes
Product Codes
Pressure Range
0-1 bar g
0-10 bar g
0-20 bar g
Process Connection
Pressure Ranges
Output
Loop Supply
Loop Resistance
NL&H*
Operating Temp
Thermal Shift Zero
Span
Safe Over-pressure
Wetted Materials
Protection
Electrical Connection
Order Code
FM5070-001-46
FM5070-010-46
FM5070-020-46
Range
(bar)
0 to 1
0 to 2
0 to 3
0 to 5
0 to 10
0 to 20
0 to 50
0 to 100
0 to 200
0 to 400
Order Code
Absolute
FM6420-001A-50
FM6420-002A-50
FM6420-003A-50
FM6420-005A-50
FM6420-010A-50
FM6420-020A-50
-
www.mess-regeltechnik.at
Gauge
FM6420-001G-50
FM6420-002G-50
FM6420-003G-50
FM6420-005G-50
FM6420-010G-50
FM6420-020G-50
FM6420-050G-50
FM6420-100G-50
FM6420-200G-50
FM6420-400G-50
HPS Series
Economic Industrial Transmitters
High
performance
pressure
transmitters offering unrivalled
chemical & corrosion resistance.
Gauge or absolute pressure is
accurately measured using a four
active-arm strain gauge bridge sensor
fused to a high-purity ceramic
diaphragm. Available with mV,voltage or
mA output.
Compact & robust, gauge and absolute,
stainless steel transmitters. ASIC signal
conditioning provides high accuracy
over wide operating temperature
range. Available with 0.5V to 4.5V ratiometric output and integrated cable for
OEM applications or 4 to 20mA and
Packard connector for industrial
applications.
Data Sheet 2703
Data Sheet 2805
Specification
Specification
Output:
Output
NL, H & R
Thermal error
Temp range
Long term stability
EMC
Vibration
Body Diameter
4 to 20mA, 0 to 100mV,
0 to 5V
Setting accuracy:
± 0.5% span
NL, H & R:
± 0.1% span
Temp range:
-20ºC to +125ºC
Thermal zero shift: ± 0.015%/ºC
Thermal span shift: ± 0.015%/ºC typical
Long term stability: 0.1% span/year
Intrinsically Safe:
Ex
Product Codes
Pressure
Range
0-1 bar g
0-1 bar abs
0-10 bar g
0-100 bar g
0-1 bar g
0-1 bar abs
0-10 bar g
0-100 bar g
0-400 bar g
0-1 bar abs
0-10 bar g
0-100 bar g
0-400 bar g
TRANSMITTERS
TRANSMITTERS
4 to 20mA or 0.5 to 4.5V
± 0.5% span
± 0.5% span, (1% for 1 bar range)
-40ºC to +105ºC
± 0.25% span/year
100V/m
20g, 10 to 2000 Hz Sinusoidal, 3 axes
22mm
Product Codes
Output
Std
10m V/V
10m V/V
10m V/V
10m V/V
4-20mA
4-20mA
4-20mA
4-20mA
4-20mA
0-5V
0-5V
0-5V
0-5V
FC-FHVAA-001
FC-FHVAA-001A
FC-FHVAA-010
FC-FHVAA-100
FA-AHVAA-001
FA-AHVAA-001A
FA-AHVAA-010
FA-AHVAA-100
FA-AHVAA-400
FA-BHVAA-001A
FA-BHVAA-010
FA-BHVAA-100
FA-BHVAA-400
Intrinsically
Safe
FA-KHVAA-001
FA-KHVAA-001A
FA-KHVAA-010
FA-KHVAA-100
FA-KHVAA-400
4-20mA (Packard)
Pressure Range
0-1 bar g
0-1 bar abs
0-10 bar g
0-100 bar g
0-200 bar g
Code
FEIT-001G-AB-XXXX-20mA
FEIT-001A-AB-XXXX-20mA
FEIT-010G-AB-XXXX-20mA
FEIT-100G-AB-XXXX-20mA
FEIT-200G-AB-XXXX-20mA
0.5V - 4.5V (300mm cable)
Pressure Range
Order Code
0-1 bar g
FEIT-001-G-AB-I12-4.5V
0-1 bar abs
FEIT-001-A-AB-I12-4.5V
0-10 bar g
FEIT-010-G-AB-I12-4.5V
0-100 bar g
FEIT-100-G-AB-I12-4.5V
0-200 bar g
FEIT-200-G-AB-I12-4.5V
* note for intrinsically safe option add to order code
☎
+43 1 706 43 000
81
PROCESS MEASUREMENT & CONTROLS Inc.
P
M
C
Process Measurement & Controls
PMC
• Established in 1963 - process specific to the
Pulp and Paper industry
• Produced in a modern facility that uses high-tech
equipment designed and built in house
• Quality is assured by uncompromising attention
to manufacturing details and calibration
procedures
Pressure Measurement
• Patented flush-mounted transmitters
• Anti-clogging
• Industry standard
• Rugged and reliable
Pressure Products
• Precision solutions for Pressure, Level and
Vacuum measurement
• Pneumatic and electronic transmitters for pulp
•
82
and water, food and beverage, pharmaceutical
and wastewater management
All stainless steel housing available
www.mess-regeltechnik.at
PROCESS MEASUREMENT & CONTROLS Inc.
sure and levels in process industries
where plugging of gauges and seals is a
problem. The small diameter of the
transmitter permits installation flush
with the inside wall of pipes 1" and larger.
This feature avoids the usual pocketing
problems encountered with conventional
flange-mounted transmitters. This PMC
product is well suited for high vibration
environments and is ideal where limited
access is a concern.
Pneumatic (1:1)
PMC Electronic Transmitters
The capacitance sensor handles overloads of up to 10 times nominal range.
The Slimline version offers a compact
design for installation in confined
spaces and measures just 1 1/16"
diameter by 4" long. The remote
electronics version offers a split unit
where the transducers are submerged and
the electronics are mounted in an accessible location for calibration, with a local
display (LCD) option.
PRESSURE
PMC Miniature Pressure and Level
Transmitters accurately measure pres-
Electronic (4-20mA)
Specification
Specification
Ranges
Level
Output
Accuracy
Mounting
Diaphragm
Temperature
Ranges
Output
Accuracy
Mounting
Diaphragm
0-10:30: 60: 100 & 150 PSIG
0-10: 25:50: 100: 300 & 500" WG
1:1, 3-15 PSIG
+/- 0.1 PSIG
Weld-on + others
Havar, Hastelloy C or Tantalum
-25ºC to 85ºC
Temperature
4.25" WG to 300 PSIG 30 & Vacuum
4-20mA
+/- 0.25%
Weld-on + others
Havar, Hastelloy C Tantalum or
Ceramic
-25ºC to 85ºC
Product Codes
Product Codes
PT-XXX-N-Ha-S
PT/SAN-XXX-Si-Ha-HT
LT/DR-XXX-N-Ha-S
LT-SAN-XXX-Si-Ha-HT
PTEL-SAN-XXX-Ha-CV/P
PT/EL-DR-XXX-Ha-CV/P
MINI-PT/EL-SAN-XXX-Ha-CV/P
MINI-PT/EL-SAN-XXX-Ha-CV/P
XXX = pressure range
☎
+43 1 706 43 000
83
ELECTRONIC PRESSURE SWITCH
Switch 2000
• Electronic pressure switch with 1 or 2 solid state contacts
• 7-segment LED display
• Microprocessor controlled
• Self monitoring with error display, all parameters are configured by keypad,
PRESSURE
tamper proof keypad lock, rugged construction, vibration and shock-proof
• Good long term stability
OEM Applications
• Hydraulics
• Pneumatics and lubrication monitoring
• Machine/machine tool industry
• Automobile industry
• Injection molding machines
Specification
Measuring element
Piezoresistive pressure sensor with stainless steel
diaphragm, microcontroller and self monitoring
0 to 10 bar - 0 to 600 bar
0.5% fs
3 digit 7-segment LED display, red, 10mm height
4-20 mA
Solid state outputs pnp-NO/NC (programmable),
adjustable switching line delay 0 to 10 s
Measuring ranges
Linearity error
Display
Output signals
Switching outputs
Temp drift of zero signal
and output (ref 20°C)
Temperature range
Media temperature range
Process connection
Protection class
Electrical connection
Process connection
Power supply
Options
0, 2%/10k from 10°C to +70°C
-10°C to +70°C
-25°C to +100°C
G 1/4 M, stainless steel, optional C-Top flange
connection
IP 65
Plug 4-pin M 12 x 1
G 1/4 M, stainless steel
15 to 32 Vdc
on request
Product Codes
Pressure range
0 to 10 bar
0 to 50 bar
0 to 100 bar 0 to 200 bar 0 to 400 bar 0 to 600 bar
1 Switching Output
2 Switching Outputs
1 Analogue Output 4-20 mA
F0428-011
F0428-017
F0428-127
F0428-012
F0428-018
F0428-128
F0428-013
F0428-019
F0428-129
F0428-014
F0428-020
F0428-130
F0428-015
F0428-021
F0428-131
F0428-016
F0428-022
F0428-132
DESIGNA®
1 Switching Output
1 Diagnosis Output
F0428-031
F0428-032
F0428-033
F0428-034
F0428-035
F0428-036
Accessories
Adapter G 1/4 F - G1/4 M thread or optimum alignment of pressure switch
Damping screw with 0.2mm restriction against quick pressure changes and high pulsation rate
Electrical plug M 12 x 1, 4-pin, with screw terminal, 90º elbow
Electrical plug M 12 x 1, 4-pin, with screw terminal, straight
84
www.mess-regeltechnik.at
Code
F0499-016
F907-0677
F907-0357
F907-0344
PRESSURE SWITCHES
• Two transistor-switching contacts
• Switch contact indication with two
LEDs
• Switch point/parameter adjustment
with PC interface or hand-held
terminal
• Mechanically
robust and
reliable
Switching output
Temp range
Media temp range
Process connection
Protection class
Elect connection
Power supply
Options
Adjustable diaphragm and piston
type pressure switches, suitable for
gases and liquids. Available in zincplated steel and stainless steel body
materials.
• Ideal for hydraulics and pneumatics
• Change-over contacts
• Compact design
Specification
Measuring Element
Range
Linearity error
Display
Pressure Switch
PRESSURE
UDS2 2-V2 Switch
Specification
Thick film ceramic sensor
2,0 to 400 bar, gauge
<±1% fs
Switch status by 2 LED,
green/yellow
2 solid state outputs, pnp NO/NC, freely adjustable
-25°C to 85°C
-25°C to 85°C
G 1/4 M, stainless steel
IP67
Plug 5-pin M 12 x 1
12 to 30 Vdc
on request
Output
Contact Rating
Process
Connection
Elect Connection
Temperature
Pressure
Dimensions
Cable Gland
Hysteresis
Wetted Materials
Product Codes
SPCO contacts
250Vac/4A (resistive)
1/4" BSP Male (G 1/4")
IP65 plug
-30°C to 120°C
100 bar on 1.5 and 10 bar steel
units; 300 bar on all others up to
100bar; 600 bar on 200 bar units
27mm AF, 26mm OD
Pg 9
10 to 30% of max, switch point,
adjustable
Viton diaphragm/piston seal
and zinc-plated steel or Stainless
Steel body
Measuring Range
2 switching outputs
Product Codes
0 - 10
0 - 50
0 - 100
0 - 200
0 - 400
F0429-001
F0429-002
F0429-003
F0429-004
F0429-005
Adj Range (bar) Tol.(bar)
Zinc Plated Steel
Stainless Steel
Accessories
Programming kit
Hand-held programmer
F0499-031
F0499-032
0.3 - 1.5
0.5 - 5
1 - 10
10 - 50
10 - 100
50 - 200
FSUCO457031
FSUCO458031
FSUCO459031
FSUCO461031
FPSW0020
FPSW0021
FPSW0022
FPSW0023
FPSW0024
FPSW0025
☎
±0.2
±0.2
±0.5
±3
±3
±5
+43 1 706 43 000
85
PRESSURE GAUGES
Pressure Gauges
The Stainless Steel Pressure Gauges of the MEX and MIX range, have been designed
for use across the measurement and control industry. The gauges are perfectly suited to
the process industries such as chemical, petro-chemical, energy and gas, as well as
food and brewing applications.
GAUGES
• All Stainless Steel gauges
• Robust for harsh environments
• Resistance to transient overpressure
• Conforms to EN837 and PED standard
Typical industries serviced
by these gauges
• Chemical
• Energy generation
• Pharmaceutical
• Food processing
• Brewing
• Bio-technology
• Nuclear
In addition to our standard range we are able
to offer a much wider range of pressure
gauges as well as all the accessories your
application requires.
Available spares and accessories
• Pressure limiters
• High temperature adapters
• Gauge cocks and valves
• Dampeners
• Siphons
• Hygienic and chemical seals
Please contact our Technical Sales Team to
discuss your spares and accessory
requirements.
86
www.mess-regeltechnik.at
PRESSURE GAUGES
Diameter
50mm (MEX2)
63mm (MEX3)
100mm (MEX5)
Direct bottom entry
1.4304 (AISI 304) Blow out disk on top
1.4404 (AISI 316L)
Plain glass
1/4" BSP as standard or NPT (M) (MEX2 + 3)
1/2" BSP as standard or NPT (M) (MEX5)
IP65
+/- 1.6% FSD (MEX2 + 3)
Class 1 (MEX5)
Mounting
Case
Wetted Parts
Window
Connection
Weatherproof
Accuracy
Diameter
Mounting
Case
Wetted Parts
Window
Connection
Weatherproof
Accuracy
GAUGES
Specification
150mm (MIX)
Direct bottom entry
1.4304 (AISI 304) Blow out disk on top
1.4404 (AISI 316L)
Plain glass
1/2" BSP or NPT (M)
IP65
Class 1
Product Codes
Range bar
50mm Code
63mm Code
100mm Code
150mm Code
-1 to 0 bar
0 to 1 bar
0 to 2.5 bar
0 to 4 bar
0 to 6 bar
0 to 10 bar
0 to 16 bar
0 to 25 bar
0 to 40 bar
0 to 60 bar
0 to 100 bar
FMEX2000*
FMEX2001*
FMEX2002*
FMEX2004*
FMEX2006*
FMEX2010*
FMEX2016*
FMEX2025*
FMEX2040*
FMEX2060*
FMEX2100*
FMEX3000*
FMEX3001*
FMEX3002*
FMEX3004*
FMEX3006*
FMEX3010*
FMEX3016*
FMEX3025*
FMEX3040*
FMEX3060*
FMEX3100*
FMEX5000*
FMEX5001*
FMEX5002*
FMEX5004*
FMEX5006*
FMEX5010*
FMEX5016*
FMEX5025*
FMEX5040*
FMEX5060*
FMEX5100*
FMIX7000*
FMIX7001*
FMIX7002*
FMIX7004*
FMIX7006*
FMIX7010*
FMIX7016*
FMIX7025*
FMIX7040*
FMIX7060*
FMIX7100*
*
*
•
For a glycerine filled gauge add ‘G’ to the end of the product code
Add suffix ‘DS’ for dual scale gauge (bar/psi)
psi and other ranges available on request, please contact our Technical Sales Team for details
☎
+43 1 706 43 000
87
DP GAUGES
Low DP Gases
GAUGES
The Magnehelic® gauge uses magnetic coupling from the movement of a silicon
rubber diaphragm onto a helical pointer drive shaft. This measurement is friction
free, accurate at very low differential pressures, and resistant to shock and vibration.
The standard aluminium housing can be flush panel mounted. Pressure connections
are duplicated on rear and side of the unit. Plugs and tube barbs supplied.
Magnehelic® Accessories
• Pipe mounting kit
• Line filter
• Portable kit
• Safety relief valve
• Air filter kit
Specification
Ranges
Media
Accuracy
Pressure
Temperature
Connections
Pascals, mm or inch WG, pitot flow
Air & non-corrosive gases
±2% FSD
15 psig max
-7°C to 60°C
1/8" NPT Female. Plugs and
adaptors for 5mm ID tube supplied
Housing
Diaphragm
Die-cast Aluminium
Silicon rubber, overpressure
protected
Zero Adjust Screw Mounted in meter face
Panel Cut Out
115mm diameter
Weight
0.5kg
Product Codes
88
Water (inches) Code
Pascals
Code
Water (mm)
Code
0-1
0-2
0-4
0-5
0-10
0-15
0-20
0-50
0-60
0-100
0-125
0-250
0-500
0-750
0-1K
0-1.5K
0-2K
0-5K
FM200060PA
FM2000100PA
FM2000125PA
FM2000250PA
FM2000500PA
FM2000750PA
FM20001KPA
FM20001.5KPA
FM20002KPA
FM20005KPA
0-50
0-100
0-250
0-500
FM200050MM
FM2000100MM
FM2000250MM
FM200050CM
Centre Zero Pascals
Code
30-0-30
60-0-60
125-0-125
FM230060PA
FM2300120PA
FM2300250PA
FM2001
FM2002
FM2004
FM2005
FM2010
FM2015
FM2020
FM2050
www.mess-regeltechnik.at
DP Gauge With Alarms
DP Gauge With Transmitter
Based on the Magnehelic® design,
this gauge retains the low DP
sensitivity and accuracy - and adds
two relay outputs for high & low DP
alarms. The Photohelic® principle
uses the standard gauge pointer to
interrupt infra-red beams at the
adjustable set points, which then
drive the output relays. High and
low set points are adjustable using
the front mounted knobs.
The
standard
easily
read
Magnehelic® dial gauge gives local
indication of very low differential
pressures in air or gas applications.
Additionally a two-wire 4 - 20mA
transmission is provided from a built
in strain gauge DP monitor, allowing
remote monitoring or control. Span
and zero adjustments are made
with a special tool (supplied), and
the unit can be flush panel mounted
using the hardware supplied.
Specification
Specification
DP Ranges
Accuracy
Media
Housing
Process Connections
Max Pressure
Temperature
Power Supply
Output
Electrical Connection
Panel Cut Out
Overall Size
Weight
GAUGES
DP GAUGES
Pascals (See order codes)
±2% FSD
Air & non corrosive gases
Die-cast Aluminium
1/8" NPT Female (rear & side)
25 psig
-5°C to 50°C
24Vdc
2 x SPDT relays, 1 Amp @
30Vdc, 0.5 Amp at 125Vac
460mm 8 core cable
123mm dia
140mm dia. x 65mm deep
0.75Kg
Product Codes
DP Range (Pascals)
Code
0-60
0-125
0-250
0-500
0-1000
F3000MR60
F3000MR125
F3000MR250
F3000MR500
F3000MR1000
DP Ranges
Output
Accuracy
Media
Housing
Connections
Pressure
Temperature
Panel Cut Out
Overall Size
Weight
Product Codes
DP Range
(Pascals)
0-60
0-125
0-250
0-500
0-750
0-1500
☎
Pascals or inch WG
4 - 20mA loop powered
(10-35Vdc)
±2% FSD
Air and non corrosive gases
Die-cast Aluminium
1/8" NPT Female
25 psig max (varies by range)
0 to 50°C
123mm dia
140mm dia. x 65mm deep
1.14Kg
+43 1 706 43 000
Code
F60560
F605125
F605250
F605500
F605750
F6051500
DP Range
(inches WG)
0-0.5
0-1.0
0-2.0
0-3.0
0-6.0
0-10.0
0-20.0
Code
F6050
F6051
F6052
F6053
F6056
F60510
F60520
89
DP FLOW TRANSMITTERS
TRANSMITTERS
The Micro-Bar range are two-wire loop powered 4 - 20mA transmitters based on a
built-in capacitance based differential pressure cell for low range measurement on air
and other dry gases. Standard pressure connections are push-fit sockets but units are
also available with 1/4" NPTF threads or 6mm O/D stainless steel compression fittings.
The liquid crystal display shows the measured pressure and status of the alarm outputs. Alternatively, when used in conjunction with orifice plates, pitots or other DP
based flow sensors, units can be configured to provide root extraction of the pressure
measurement to display flow rate. Two switch outputs are programmable as flow or
pressure setpoints or, for flow measurement, to
provide a totaliser output pulse.
• Built in square root option
• Totaliser pulse output for all flow
applications
• Hi/Low volt-free contact outputs for
alarm applications
• Adjustable averaging to smooth out flow
fluctuations
Data Sheet 1720
Specification
Media
Process
Connections
Air and non-corrosive dry gases
2 x pushfit connectors for 4mm
OD tubing (1/4" NPTF available to
special order)
Static Pressure For DP ranges >1000Pa: 30kPa max
For DP ranges >1000Pa: 10bar max
Over Range
5 times DP range max
Temperature
0 to 40ºC
Outputs:
Current 4-20mA loop powered
Switches Two volt-free solid-state relays (NO/NC)
110Vac/dc, 1 Amp max
Loop Supply
Loop Resistance
Output Range
Functions
Display
Accuracy
Protection
Electrical
Connections
10 to 50Vdc
700W max @ 24V
Adjustable 20% to 100% of model
DP range
Linear or square root
2 line x 16 character LCD
±0.5% of max DP
IP66
2 x M20 cable glands
Product Codes
Range
0-30 Pa (0.1" WG)
0-100 Pa (0.4" WG)
0-150 Pa (0.6" WG)
0-300 Pa (1.2" WG)
0-1000 Pa (4" WG)
Code
FMB0-DR-01-ST
FMB1-DR-01-ST
FMB1A-DR-01-ST
FMB2-DR-01-ST
FMB3-DR-01-ST
Range
0-3000 Pa (12" WG)
0-10 KPa (40" WG)
0-30 KPa (120" WG)
0-1 Bar (400" WG)
Code
FMB4-DR-01-ST
FMB5-DR-01-ST
FMB6-DR-01-ST
FMB7-DR-01-ST
Replace -ST with -CF for 6mm O/D stainless steel compression fittings
90
www.mess-regeltechnik.at
REGULATORS
High Precision Pressure
Regulator
These electro-mechanical instruments
are designed to convert electrical
current to a pneumatic output. The
converter is based upon the well
proven electro-magnetic force balance
technique for consistent and reliable
performance.Model 100X is designed
for low pressure and model 101X is
suitable for high pressure applications.
Both are suitable for control room or
field mounting.
Precision regulators are suitable for
instrumentation applications demanding
particularly accurate pressure regulation.
These sophisticated precision controllers
can be used where exact repeatability
and freedom from drift coupled with
superior flow and regulation characteristics
are specified. Particularly suitable for
dead end or low flow applications.
• Very high accuracy
• Capsule rather than
REGULATORS
Electronic I/P Converters
• ATEX certified units available
• Minimum vibration effects
• IP65 protection
• Mounting bracket
rolling diaphragm
and connector
included
Specification
Die cast zinc alloy. Black vinyl
finish
Diaphragm
Nitrile rubber
Capsule
Stainless Steel
Mounting
Any orientation in-line or panel
Pneumatic Conn.
1/4" NPT
Weight
635g
Input Pressure (max) 10 bar regulated
Media
Air or dry non corrosive gas
Flow (mid range)
25m3/hr
Consumption
0.15m3/hr
Exhaust Capacity
3.4m3/hr @ outlet 5 psi above
set point
Self Venting
Standard model is fitted with a
Handwheel
manually operated handwheel
for precise pressure adjustment
Accuracy
± 1%
Response Time
1 second typical
Temperature
-45°C to 85°C
Protection
IP65
Flow Capacity
300 L/min (10SCFM)
Connections
1/4" NPT female
Model 100X Low Pressure
Linearity Error
0.5%
Hysteresis
0.35%
Input Pressure
1.4 - 4.5 bar (20-80 psig)
0utput Pressure
0.2 - 1 bar (3-15 psig)
Air Consumption
0.85 L/min (0.03 scfm)
Input Signal
4-20mA 2-wire
Model 101X High Pressure
Linearity Error
1%
Hysteresis
0.5%
Input Pressure
10 bar (150 psig) max
Output Pressure
0.14-8 bar (3-120 psig)
Consumption
1.75 L/min (0.06 scfm)
Input Signal
4-20mA 3-wire
Product Codes
Product Codes
Specification
Body
Pressure Range
2-25 psi
2-60 psi
2-120 psi
Type
100X
101X
Code
F59281312
F59281313
F59281315
Code
F59424
F59425
•100X is also available approved to EEX ia IIC T4
☎
+43 1 706 43 000
91
REGULATORS
Pressure Reducing Valve
REGULATORS
This brass pressure reducing valve
for non corrosive liquids is a low cost
regulator for 3/8" to 3" lines. The
adjustment in the base is via an Allen
key protected by a plastic cap. A
pressure gauge can be used in the
top of the valve to monitor outlet
pressure.
• Adjustable outlet range 0.5 - 7 bar
• 15 bar inlet pressure
• Protects against
water hammer
A range of general purpose nonrelieving water pressure regulators
for use with potable and general
salty water. UK water by-law scheme
listed.
• Non-relieving
• Durable brass body construction
• Oil resistant rubber valve face
• Complete shut-off
• Recommended for
water service lines
• For water supply
• Nylon reinforced
up to 80°C
synthetic rubber
diaphragm
Specification
Specification
Body
Valve seat
Spring
O-Rings
Gauge port
Max Temp
Inlet Working
Pressure
Body
Diaphragm
Maximum Flow
Nickel plated Brass
Stainless Steel AISI 304
Zinc coated Silicon steel
Anti-Ageing Nitrile rubber PB 701
1/4" BSP
70°C
3/8 to 2" up to 15 bar
21⁄2" to 3" up to 25 bar
BSPF Size
3/8"
1/2"
3/4"
1"
11⁄2"
2"
3"
Brass
Synthetic rubber
Typically at 7 bar inlet,5.5 bar
outlet,pressure drop 1 bar - 3 L/min
Port Size
G1/4"
Gauge Ports
2 x 1/8" BSPT
Max Primary Pressure 28 bar
Max Temperature 80°C
Product Codes
Product Codes
92
Water Pressure Regulator
Non-Relieving
Code
F5919703
F5919704
F5919706
F5919708
F5919712
F5919716
F5919724
Pressure range
0.07 to 0.7 bar
0.07 to 3.5 bar
0.14 to 7.0 bar
Panel mounting bracket
with panel nut
Code
F48760102
F48760103
F48760104
F48790104
www.mess-regeltechnik.at
Water Pressure Regulator
Pressure Relief Valve
A range of water pressure regulators
suitable for use on potable as well as
general duty water systems and
manufactured from National Water
Council approved materials
This pressure relief valve for water, air,
gas, steam or non-corrosive liquids is
adjustable over the range 1 - 12 bar,
using the top mounted screw and locknut. When line pressure exceeds the
preset value, the valve opens and
discharges to the drain line. Units are
available for line sizes from 3/8" to 3"
BSP.
• Metal contact parts are dezincified
•
•
•
•
brass, typeCZ 132 to BS 2872/2874
or stainless steel
Balanced valve design ensures a
smooth, quick response to sudden
flow demands with low pressure
drop
Easy servicing without removal
from water line
Panel mounting facility
Accessories include
metal panel mount
bracket and nut
• Suitable for water, steam & non-
REGULATORS
REGULATORS
corrosive liquids
• Teflon seat for maximum 180°C
operation
• Adjustable relief pressure range
1- 12 bar
• Compact design
Specification
Port sizes:
Non-relieving
primary pressures
Regulated pressures*
Operating temp
Gauge ports
G 1/4"
Standard ports to ISO 1179.
Accepts ISO 228 (BS2779) parallel
or ISO 7 (BS 21) taper connections
For alternative threads consult
factory
Up to 31.5 bar (450psi)
0.7 to 8 bar (10 to 125 psi) standard
2°C to 100°C (35°F to 212°F)
G 1/8"
Specification
Body
Valve seat
Spring
Regulator
Max temp
Relief Pressure
Brass for sizes 3/8"- 1"
Bronze for sizes 11⁄4" - 3"
Brass and PTFE
Zinc plated Carbon Steel C72
Brass
180°C
15 - 170 psi (1 - 12 bar)
* will provide complete shut off
Product Codes
Product Codes
Type
Panel mounting bracket/ring
0.07 to 0.7 bar
0.07 to 3.5 bar
0.14 to 7.0 bar
BSPF (Size)
3/8"
1/2"
3/4"
1"
Code
48780101
487601-02
487601-03
487601-04
☎
Code
F5919803
F5919804
F5919806
F5919808
+43 1 706 43 000
BSPF (Size)
11⁄2"
2"
3"
Code
F5919812
F5919816
F5919824
93
TEMPERATURE OVERVIEW
TEMPERATURE
RM&C Brearley
UK’s largest manufacturer of thermocouples
• The
and temperature probes
• Technical help desk for application solutions
• Standard and custom designs
• Full range of associated accessories
• Fast track system for urgent deliveries
Temperature Measurement
• Mineral insulated thermocouples from -200°C to 1300°C
• Rare metal thermocouple assemblies up to 1800°C
Specification
• PT100/RTD thermocouples from -200°C to 550°C
• Non contact pyrometry up to 3000°C
Temperature Products
• Controllers and displays
• Recorders and dataloggers
• Transmitters and signal conditioning
• Accessories and fittings
• Configuration, installation and commissioning
Product Codes
94
www.mess-regeltechnik.at
Thermocouples
Refractory Sheaths
and Cables
• Range -200°C to 1800°C
• All industries supplied
• All types manufactured
& components
• Materials
held in stock
• In-house calibration
• Full repair service
• Sheaths/tubes up to 1800°C
• Excellent corrosion resistance
• Range of materials
• Cables to suit all thermocouples
• Colour coded to IEC 584-3
• Ex-stock
Temperature
Transmitters
Latis Level & Temp
Monitoring
• Head or DIN rail mounted
• Thermocouple or Pt100
• 0/4-20mA output
• Intrinsically safe options
• Open HART® protocol
• Alarm relay option
temperature and water
• Combined
interface sensor for liquid tanks
• Single entry for two sensors
for hazardous area zone 1
• Certified
operation
• Calibration and maintenance free
level detection accuracy
• High
+/- 2mm
Infra-red
Thermometers
Controllers, Recorders
and Dataloggers
• 0ºC to 3000ºC
• Adjustable emissivity
• Datalogging function
• Fixed or portable
• UKAS calibration
• Process controllers and indicators
• Graphic recorders
• Stand alone or network solutions
• SCADA & data acquisition packages
• Small/large frame paper recorders
• Complete system solutions
☎
+43 1 706 43 000
TEMPERATURE
TEMPERATURE OVERVIEW
95
TEMPERATURE
TEMPERATURE
Founded in the early 1900’s by Harry
Brearley, the inventor of Stainless Steel,
the business is now the No 1 supplier to
the UK Steel and Glass industries. Over
the years the business has continued to
develop its products and services to
satisfy the wider industry requirements
and now has an unrivalled capability.
Under the Brearley brand RM&C are the
largest manufacturer of industrial
thermocouples and temperature
probes in the UK. With a wealth of
experience our technical help desk can
provide solutions through custom or
standard designs and provide a full
range of accessories and fast track
delivery for urgent requirements.
Products range from industrial
thermocouple types, mineral insulated
and rare metal thermocouples and
assemblies, to Pt100/RTD and noncontact pyrometry covering the range 0°C to 3000°C. Additionally we supply,
configure, install and commission
process controllers, indicators, chart
recorders and dataloggers. We can
satisfy
all
your
temperature
measurement requirements.
Applications
96
•
•
•
•
•
•
•
•
Steel processing
Glass and ceramic
Food procesing
Heat treatment
Oil and gas pipelines
Brewing
Injection moulding
Custom designs for rubber,
plastics, food and hospital use
•
Aerospace*
* RM&C are able to manufacture
thermocouples to the requirements of
AMS2750. Our UKAS laboratory can also
calibrate your instrumentation to the
requirements of AMS2750.
www.mess-regeltechnik.at
TEMPERATURE
TEMPERATURE
Complete Range of Temperature Sensors
•
•
•
•
•
•
•
Temperature range -200°C to 1800°C
Mineral insulated - types N, K, J, E, T
Rare metal - types R, S, B
Resistance thermometers - 1/10 DIN, class A, class B, 2/3/4 wire - single or duplex
Complete range of flexible thermocouples
Wide range of bare wire thermocouples
Wide choice of sheath materials
In addition RM&C stock an extensive range of cables, plugs and sockets.
☎
+43 1 706 43 000
97
TEMPERATURE
Eurotron
TEMPERATURE
The MicroCal 20 Series documenting process calibrators are a rugged hand tool for
calibration, maintenance and trouble shooting of virtually all control process
instrumentation.
The IS versions are certified to ATEX II 1 G EEx ia II C T4,
and are suitable for use in hazardous areas.
•
Calibrate temperature, pressure, voltage, frequency
and resistance
• Dual channel display for simultaneous
measure/source
• Measure and source 14 types of thermocouple and
10 RTDs
• 24 Vdc loop power supply (12 Vdc for IS)
• Connection for internal and external presssure
module up to 700 bar
• Pressure switch test and leak test
• Rechargeable battery and charger
• Hold, zero, scale, min/max/avg, tare and flow
RM&C Instrumentation
An official Eurotherm technical partner
• Recorders
(Paper & Paperless)
• Indicators
• Alarm Units
• Controllers
• Programmers
• Other products:
• Solid State Relays
• Power Controllers
• Thyristors
98
www.mess-regeltechnik.at
Thermal Imaging Camera
Brearley IR
The IRI 4010 is an innovative hand
held thermal imager which offers
outstanding imaging and temperature
measurement performance together
with the traditional RM&C features
of flexibility, ease of use and minimal
cost.
The compact infrared thermometer
for industrial and clean area
applications.
For use at all engineering levels.
• -30 to 500°C temperature range
• Comfortable pistol grip
• Easy to use (°C/°F selectable)
• Just a “click” to measure
• Immediate response
• Ultra sharp laser sighting
• Large backlight LCD display
• Preset adjustable emissivity
• Max., min. & diff. reading
• High and low alarm
• Tripod mounting
TEMPERATURE
TEMPERATURE
• Only 0.75 kg
• 160 x 120 image
• Simple operation
• Large, clear display
• Multiple temperature
measurements
• Lowest cost high definition imager
on the market
• Stores up to 1000 images
• Temperature range -10ºC to +250ºC
• Fully Radiometric
☎
+43 1 706 43 000
99
SERVICE/CALIBRATION
accredited for 4 fields of expertise
• UKAS
Pressure - Temperature - Flow - Electrical
• Over 30 years experience
• Flexibility to meet your demands - on or off site
and efficient service, maintenance
• Fast
and repair service
Laboratory Parameters
• Temperature up to 2200°C
• Flow up to 2400 L/min
• Pressure up to 1200 bar
• Electrical up to 1000V and 200A
On-site Service
• Cost-effective control solutions
with our mobile team of UKAS
• Calibration
accredited engineers
• Supported from 2 regional branches
• Fast and effective breakdown service
in checking condition of existing
• Assistance
equipment
100
www.mess-regeltechnik.at
It is approved to the highest
internationally recognised standards,
including ISO9001:2000 and ISO17025.
UKAS accredited Laboratories provide
traceability to international standards for
pressure, electrical, flow and temperature
measurement.
Capabilities
Temperature
Thermocouples
Non-contract thermometry
LIG Thermometers
Resistance Thermometers
Furnace/Ovens
Autoclave/Media Preps
Environmental Chambers
Indicators & Probes
-196°C to 1600°C
-50°C to 2200°C
-80°C to 300°C
-196°C to 300°C
Amb to 1600°C
Working range
Up to 300°C
-196°C to 1600°C
SERVICE/CALIBRATION
SERVICE & CALIBRATION
Pressure
Pneumatic
Hydraulic
Barometers
Up to 25 bar
Up to 1200 bar
200 mbar to 2000 mbar
Flow
Gas
Water
5cc - 650 L/min
0.1 L/min - 2400 L/min
Electrical
Indicators/Controllers
Chart Recorders/Dataloggers
Digital Multimeters
Resistance Boxes
Other Electrical
☎
+43 1 706 43 000
16th Edition
Clampmeters
Stopwatches
Process Calibrators
101
PUMPS OVERVIEW
Pumps and Services
PUMPS
Features
run dry without damage
• Can
• Self-priming
and metering - constant output
• Dosing
pulsation
• Low
range from 1 bar to 172 bar
• Pressure
smooth operation
• Quiet
and quick to maintain
• Easy
• Compact
• Energy - efficient (80-85%) Hydra-cell
Benefits
• Metal pumps for abrasion resistance, solvents
• and hydrocarbons
size up to 10mm
• Solid
size to 1/4" to 3"
• Port
mechanical seals
• No
variety of liquids handled (clean/dirty/viscous
• Wide
hot/flammable/acidic/abrasive)
Plastic pumps for strong acids and caustics
Specification
On-site Service
pump solutions
• Cost-effective
and effective pump repairs
• Fast
of pumps and spares held in stock
• Selection
effective breakdown service
Product
Codes
• Fast and
102
www.mess-regeltechnik.at
PUMPS OVERVIEW
Series 2000 Utility Pumps
PUMPS
Wanner Hydra-Cell Pumps
Models
G-20
G-03
G-10
G-15/17
G-25
G-35
L/min
Up to 3.8
Up to 11.3
Up to 30.3
Up to 56
Up to 75.7
Up to 140
Code
G21XDBTHHEMG
G03XKBTHHECA
G10XKCTHFEYA
G15XDBTHFEYA
G25XKCTHFEYA
G35XKCTHFEYA
Yamada Pumps
Model Impeller
Motor Max Max Max Code
Flow Head Solid
L/min (m) (mm)
2051
2053
2003
2021
2103
230V
230V
230V
230V
110V
Neoprene
Nitrile
Nitrile
Neoprene
Nitrile
6
6
30
30
30
30
22
15
30
15
2
2
6
6
6
F48102544
F48102545
F48102541
F48102542
F48102543
Yamada Drum
Pumps
(Air driven)
(Air driven)
Size
Pump capacity - drum pumps
Pump capacity - pumps
1/4"
3/8"
1/2"
3/4"
1"
1-1/2"
2"
3"
L/min
10
20
50
100
150
250
500
800
10
20
50
100
150
200
Please contact our Technical Sales Team to discuss your application
☎
+43 1 706 43 000
103
SYSTEMS OVERVIEW
SYSTEMS
Systems
• Nuclear sampling and monitoring specialists
• Bespoke equipment
• Turnkey projects
• Process measurement & control
• Solutions provider
Markets
• Nuclear / Defence
• Energy / Utilities
• Chemical / Petro-Chem
• Food & Beverage
• Medical
• Others
Capabilities
• Project Management
• Systems design
• Surveying through to commissioning
• Radiologically classified staff
• Security cleared staff
104
www.mess-regeltechnik.at
Electrical &
Instrumentation
Cabinets
SYSTEMS
SYSTEMS OVERVIEW
Continuous
Emission
Monitoring
Systems
Duct Flow
Measurement
& Isokinetic
Sampling
☎
+43 1 706 43 000
105
CE
LA
EP
R
SPE
CI
FY
MAINTAIN
NUFACTURE
MA SUPPLY
&
C
☎
A
LI
BR
AT E
+43 1 706 43 000
INS
L
TA
INSTRUMENTATION
RM&C INSTRUMENTATION
L
107
www.mess-regeltechnik.at
www.platon-direct.eu
• Manufacture and supply of
flow, pressure, temperature
and level instrumentation
• Calibration and repair
service either in our labs
or on-site
LICO Electronics GmbH
Klederinger Str. 31
A-2320 Kledering, Austria
[email protected] www.lico.at
Tel. +43 1 706 43 00
www.mess-regeltechnik.at
www.platon-direct.eu