Release Notes for the Catalyst 8510 and the
LightStream 1010 Switch for Cisco IOS
Release 12.1(26)EB2, Part 1: System
Requirements
August 02, 2007
Catalyst 8510 and LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2
Text Part Number: OL-14426-01
This document describes the features and caveats for Cisco IOS Release 12.1(26)EB2 software for the
Catalyst 8510 and the LightStream 1010 switch.
Note
All information pertains to both the Catalyst 8510 and LightStream 1010 switch platforms, unless
differences between the platforms are noted in the text.
Contents
This document includes the following sections:
•
Introduction, page 2
•
System Requirements, page 2
•
New and Changed Information, page 11
•
Caveats, page 17
•
Restriction, page 17
•
Interoperability, page 18
•
Y2K Compliance, page 18
•
Related Documentation, page 18
•
Obtaining Documentation, page 18
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2005 Cisco Systems, Inc. All rights reserved.
Introduction
•
Obtaining Technical Assistance, page 19
•
Obtaining Additional Publications and Information, page 21
Introduction
The Catalyst 8510 and LightStream 1010 switch provide switched ATM connections to individual
workstations, servers, LAN segments, or other ATM switches and routers using fiber-optic, unshielded
twisted-pair (UTP), and coaxial cable.
Note
The ATM switch processors (hardware version 4.0 or higher) and all port adapters can be installed in the
Catalyst 5500 switch chassis.
The Catalyst 8510 CSR belongs to a class of high-performance Layer 3 switch routers. It is optimized
for the campus LAN or the intranet and provides both wirespeed Ethernet routing and switching services.
System Requirements
This section describes the system requirements for Cisco IOS Release 12.0 and includes the following
sections:
•
Memory Requirements for Catalyst 8510 MSR and LightStream 1010, page 2
•
Memory Requirements for Catalyst 8510 CSR, page 2
•
Hardware Supported, page 3
•
Determining Your Software Release, page 5
•
Other Firmware Code, page 5
•
Feature Set Tables, page 5
•
Release Names, Versions, and Part Numbers, page 9
Memory Requirements for Catalyst 8510 MSR and LightStream 1010
The DRAM memory configuration is 64-MB DRAM (MEM-ASP64M), which is the default for both the
Catalyst 8510 and the LightStream 1010 switch platforms.
Memory Requirements for Catalyst 8510 CSR
Table 1 lists the default Flash and DRAM memory for the Catalyst 8510 CSR, as well as memory
upgrade options.
2
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
System Requirements
Table 1
Catalyst 8510 CSR Default Memory and Upgrade Options
Memory Type
Catalyst 8510 CSR Defaults Upgrade Options
Flash memory 16 MB
MEM-ASP-FLC16M=
MEM-ASP-FLC20M=
DRAM
None
64 MB
To download and store a copy of the Catalyst 8510 CSR software image, we recommend using a
minimum 20 MB Flash PC Card, which allows you to have two or more images installed at the same
time.
The Catalyst 8510 CSR boots from its onboard Flash memory by default. To change this default to boot
from a Flash PC Card instead, you must change the configuration register setting to 0x2102. Refer to the
Layer 3 Switching Software Feature and Configuration Guide for more information.
Hardware Supported
Table 2 lists the interfaces supported by both the Catalyst 8510 MSR and LightStream 1010 switch and
Cisco IOS Release 12.1(26)EB2 and their minimum software release requirements. All platform specific
requirements are noted in the table. Table 2 lists this information for the Catalyst 8510 CSR.
Note
Although minimum software versions are listed, we strongly recommend that you use the
latest available software release for all Catalyst 8510 and LightStream 1010 hardware.
Table 2
Catalyst 8510 MSR and LightStream 1010 Interface Modules and
Minimum Software Required
Part Number
Description
Minimum Software
Version Required
WAI-OC3-4MM
4-port STS-3c/STM-1 multimode fiber port adapters
WAS1-1
WAI-OC3-4SS
4-port STS-3c/STM-1 single-mode fiber port adapters WAS1-1
WAI-OC3-4U5
4-port STS-3c/STM-1 UTP-5 port adapters
WAS1-1
WAI-OC3-4SSLR
4-port STS-3c/STM-1 SMF long reach port adapters
WAS3-2
WAI-OC3-1S3M
OC-3 mix port adapter module, 1 IR+ port and 3 MM WAS3-1
ports
WAI-OC12-1MM
1-port STS-12c/STM-4c multimode fiber port adapters WAS1-2
WAI-OC12-1SS
1-port STS-12c/STM-4c SMF port adapters
WAI-OC12-1SSLR
1-port STS-12c/STM-4c SMF long reach port adapters WAS3-2
WAI-ATM25-12P
12-port ATM 25 port adapters with 96-pin telco cable WAS3-2
WAI-T3-2BNC
2-port DS-3 port adapters
WAS1-1
WAI-E3-2BNC
2-port E3 port adapters
WAS1-1
WAI-T3-4BNC
4-port DS-3 port adapters
WAS3-1
WAI-E3-4BNC
4-port E3 port adapters
WAS3-3
WAI-T1-4RJ48
4-port T1 (ATM) with RJ-48 interface port adapters
WAS3-1
WAS1-1
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
3
System Requirements
Table 2
Catalyst 8510 MSR and LightStream 1010 Interface Modules and
Minimum Software Required (continued)
Part Number
Description
Minimum Software
Version Required
WAI-E1-4RJ48
4-port E1 (ATM) with RJ-48 interface port adapters
WAS3-1
WAI-E1-4BNC
4-port E1 (ATM) with BNC interface port adapters
WAS3-1
WAI-T1C-4RJ48
4-port T1 (circuit emulation) with RJ-48 interface port WAS3-1
adapters
WAI-E1C-4RJ48
4-port E1 (circuit emulation) with RJ-48 interface port WAS3-1
adapters
WAI-E1C-4BNC
4-port E1 (circuit emulation) with BNC interface port WAS3-1
adapters
L1010-PWR-DC
Power supply DC
L1010-ASP-B-FC1
WAS3-1
1
2
ASP with FC-per-class queuing (FC-PCQ )
1
WAS1-3
L1010-ASP-B-FCPFQ ASP with FC-per-flow queuing (FC-PFQ )
WAS4-1
L1010-ASP-C-FC1
W5-5
Hot-swappable ASP with FC-PCQ
L1010-ASP-C-FCPFQ Hot-swappable multiservice switch route processor
W5-5
C85MS-4E1-FRRJ48
4-port CE1 with RJ-48c interface Frame Relay port
adapters
W5-5
WS-X5165
ATM-Fabric Integration Module for the Catalyst 5500 W5-5
C85MS-1DS3-FRBNC 1-port CDS3 Frame Relay port adapter
W5-9
C85MS-ATM25-4P
W5-9
C85MS-8T1-IMA
4
3
4-port 25-Mbps port adapter
8-port T1 port adapter with IMA
4
Catalyst 8510
S851R2-12.0.4W
LightStream 1010
SL10R2-12.0.4W
C85MS-8E1-IMA-120 8-port E1 port adapter with IMA
Catalyst 8510
S851R2-12.0.4W
LightStream 1010
SL10R2-12.0.4W
C8510-ARM-64K
ATM router module
S851R2-12.0.10W5
C8510-ACL
ACL6 daughter card
S851R2-12.0.10W5
C85GE-1X-16K=
1-port Gigabit Ethernet 16K
S851R2-12.0.10W5
C85GE-1X-64K=
1-port Gigabit Ethernet 64K
S851R2-12.0.10W5
C85FE-8T-16K=
8-port 10/100 Fast Ethernet with RJ-45 16K
S851R2-12.0.10W5
C85FE-8T-64K=
8-port 10/100 Fast Ethernet with RJ-45 64K
S851R2-12.0.10W5
C85FE-8F-16K=
8-port 10/100 Fast Ethernet with MT-RJ 16K
S851R2-12.0.10W5
C85FE-8F-64K=
8-port 10/100 Fast Ethernet with MT-RJ 64K
S851R2-12.0.10W5
C8510-TSCAM-2P
Traffic-Shaping Carrier Module (TSCAM)
Catalyst 8510
MSR:
S851R2-12107EY
LightStream 1010:
SL10R2-12107EY
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
System Requirements
1. ASP = ATM switch processor.
2. FC-PCQ = feature card per-class queuing.
3. FC-PFQ = feature card per-flow queuing.
4. IMA = inverse multiplexing over ATM.
5. The LightStream 1010 switch requires the ASP-C with FC-PFQ to support the ATM router module.
6. ACL = access control list.
Determining Your Software Release
To determine the version of Cisco IOS software currently running on either the Catalyst 8510 or the
LightStream 1010 switch, log in to the switch and enter the show version EXEC command. The
following is sample output from the show version command. The version number is indicated on the
second line as shown:
Cisco Internetwork Operating System Software
IOS (tm) LS1010 W5-5 Software (LS1010-WP-M), Version 12.1(26)EB2
Additional command output lines include more information, such as processor revision numbers,
memory amounts, hardware IDs, and partition information.
Other Firmware Code
Some of the port adapters supported on the Catalyst 8510 and LightStream 1010 switch have
upgradeable FPGA and functional images. The FPGA and functional images include caveat fixes, but in
most cases, it is not necessary to upgrade. The release notes that describe the caveats from the FPGA
and functional images are available on the World Wide Web at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/l3sw/8540/rel_12_0/w5_6f/rel_note/fpga_rn/ind
ex.htm
For information describing the firmware update process, refer to the section “Maintaining Functional
Images (Catalyst 8510 and LightStream 1010)” in the chapter “Managing Configuration Files, System
Images, and Functional Images” in the ATM Switch Router Software Configuration Guide.
Feature Set Tables
The Cisco IOS release software is packaged in feature sets (also called software images) depending on
the platform. Each feature set contains a specific set of Cisco IOS features. Table 3 lists the Cisco IOS
software feature sets available for the Catalyst 8510 MSR and LightStream 1010 switch in Cisco IOS
Release 12.1(26)EB2.
Note
All Catalyst 8510 CSR features are also applicable to Catalyst 8510 MSR.
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
5
System Requirements
Table 3
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch
Feature Set
Introduced in Release
Left-justified E.164 AFI support
12.1(5)EY1
SNMP
1
12.1(5)EY1
Asynchronous support
2
12.1(5)EY1
3
PPP (SLIP /PPP)
IP
12.1(5)EY1
4
12.1(5)EY1
NTP
5
12.1(5)EY1
TACACS+6
12.1(5)EY1
Telnet
12.1(5)EY1
7
Point-to-point and point-to-multipoint permanent VCCs and VPCs
12.1(5)EY1
Point-to-point and point-to-multipoint switched VCCs and VPCs (UNI
3.0)
12.1(5)EY1
Point-to-point and point-to-multipoint switched VCCs and VPCs (UNI
3.1)
12.1(5)EY1
Point-to-point and point-to-multipoint switched VCCs and VPCs (UNI
4.0)
12.1(5)EY1
Multipoint-to-point UNI signaling
12.1(5)EY1
Soft VCCs and VPCs
12.1(5)EY1
VP tunneling
12.1(5)EY1
VPI/VCI range support in ILMI 4.0
12.1(5)EY1
PNNI hierarchy
12.1(5)EY1
ILMI version 4.0
12.1(5)EY1
IISP
9
12.1(5)EY1
10
11
12
13
14
LANE client (LEC ) and LANE Services (LES /BUS /LECS )
on ASP15
12.1(5)EY1
Token Ring LANE services
12.1(5)EY1
ATM ARP
16
server on ASP
12.1(5)EY1
ATM ARP client on ASP
12.1(5)EY1
ATM tag switch router (TSR)
12.1(5)EY1
Port snooping
12.1(5)EY1
17
F4 and F5
12.1(5)EY1
E.164 address translation
12.1(5)EY1
E.164 autoconversion
12.1(5)EY1
Circuit emulation
12.1(5)EY1
ATM access lists
12.1(5)EY1
ATM accounting
12.1(5)EY1
OAM
ATM RMON
6
8
18
12.1(5)EY1
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
System Requirements
Table 3
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch
(continued)
Feature Set
Introduced in Release
Multiple, weighted, dynamic thresholds for selective packet marking and 12.1(5)EY1
discard
Shaped VP tunnels for CBR traffic (FC-PFQ only)
12.1(5)EY1
Substitution of other service categories in shaped VP tunnels (FC-PFQ
feature cards only)
12.1(5)EY1
Dual leaky bucket policing (FC-PFQ feature cards only)
12.1(5)EY1
Scheduler/Service Class/PVC configuration for FC-PFQ feature cards
12.1(5)EY1
Logical multicast support (up to 254 leaves per output port, per
point-to-multipoint VC) (FC-PFQ feature cards only)
12.1(5)EY1
Network clocking enhancements for smooth switchover (FC-PFQ feature 12.1(5)EY1
cards only)
Per-VC or per-VP nondisruptive snooping (FC-PFQ feature cards only)
12.1(5)EY1
19
Support for non-zero MCR on ABR connections (FC-PFQ feature cards 12.1(5)EY1
only)
Access lists on ILMI registration
12.1(5)EY1
CUGs
12.1(5)EY1
ATM soft restart
12.1(5)EY1
ATM accounting enhancements
12.1(5)EY1
CISCO-SYSLOG-MIB support
12.1(5)EY1
CISCO-CONFIG-COPY-MIB support
12.1(5)EY1
Signaling diagnostics and MIB
12.1(5)EY1
Supplemental AToM MIB
12.1(5)EY1
Frame Relay to ATM interworking features on the channelized E1 port
adapter
12.1(5)EY1
Hierarchical VP tunnels
12.1(5)EY1
Remote logging for accounting
12.1(5)EY1
Tag switching VC-merge on non-UBR VP tunnels and hierarchical VP
tunnels
12.1(5)EY1
PNNI complex node representation
12.1(5)EY1
Support for ATM-fabric integration module in Catalyst 5500
12.1(5)EY1
PNNI explicit paths
12.1(5)EY1
PNNI alternate link selection
12.1(5)EY1
Tag switching CoS
12.1(5)EY1
Network Clock Distribution Protocol
12.1(5)EY1
Simple Gateway Control Protocol
12.1(5)EY1
Inverse Multiplexing over ATM (IMA) groups
12.1(5)EY1
ATM End System Address (AESA) gateway
12.1(5)EY1
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
7
System Requirements
Table 3
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch
(continued)
Feature Set
Introduced in Release
ATM overbooking
12.1(5)EY1
Framing overhead
12.1(5)EY1
NCDP MIB Support
12.1(5)EY1
20
L3-ATM routing and bridging via RFC 1483 (ATM router module)
12.1(5)EY1
Point-to-point subinterfaces, only point-to-multipoint subinterfaces are
supported
12.1(5)EY1
Power-on-diagnostics
12.1(5)EY1
ITT enhancements
12.1(6)EY
VBR on ATM router module support
12.1(7a)EY
Shaped tunnel support for ATM router module
12.1(7a)EY
Rate limiting
12.1(7a)EY
CiscoView
12.1(7a)EY
Radius support (TACACS+-like authentication)
12.1(7a)EY
Priority soft PVC preservation on IMA bandwidth reduction
12.1(10)E
Standard Signaling for Frame Relay soft PVCs
12.1(10)E
ATM threshold group enhancements
12.1(10)E
MPLS LDP
21
support for LSR
22
12.1(10)EY
Frame Relay PVCs terminated on ATM router module
12.1(10)EY
SONET MIB (RFC 2558)
12.1(10)EY
Two ended soft VC configuration
12.1(10)EY
PNNI connection trace
12.1(10)EY
SNMP provisioning of ATM interface traps to an SNMP host
12.1(12c)E
Traffic shaping on well-know VCs
12.1(12c)E
SSH (Secure Shell)
12.1(12c)EY
CES switched VCs
12.1(12c)EY
SNMP version 3
12.1(12c)EY
Point-to-multipoint soft PVCs
12.1(13)EB1
Overflow queuing for VBR-nrt on Frame Relay interface modules
12.1(13)EB1
Configuring Frame Relay frame size for Frame Relay-ATM interworking 12.1(13)EB1
8
Soft-PVC support on ATM 0 interface
12.1(13)EB1
RFC-2515 support
12.1(13)EB1
Traffic parameter modification for soft VCs and soft VPs
12.1(13)EB1
SNMP support for ARM subinterface
12.1(14)E1
CES MIB
12.1(14)EB1
SSH server version 2
12.1(19)EB
SSH version 2 client
12.1(20)EB
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
System Requirements
Table 3
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch
(continued)
Feature Set
Introduced in Release
Explicit Paths on CES VCs
12.1(22)EB
Redundant soft-PVC and soft-PVP destinations
12.1(22)EB
ATM Forum CES MIB Version 2 support
12.1(22)EB
Pass along bit support for ATM signaling messages
12.1(22)EB
1. SNMP = Simple Network Management Protocol.
2. PPP = Point-to-Point Protocol.
3. SLIP = Serial Line Internet Protocol.
4. IP = Internet Protocol.
5. NTP = Network Time Protocol.
6. TACACS+ = Terminal Access Controller Access Control System Plus.
7. VCCs = virtual channel connections.
8. VPCs = virtual path connections.
9. IISP = Interim-Interswitch Signaling Protocol.
10. LANE = LAN emulation.
11. LEC = LAN emulation client.
12. LES = LAN emulation server.
13. BUS = broadcast and unknown server.
14. LECS = LAN emulation configuration server.
15. ASP = ATM switch processor.
16. ARP = Address Resolution Protocol.
17. OAM = Operation, Administration, and Maintenance.
18. RMON = Remote Monitoring.
19. MCR = minimum cell rate.
20. You can download the Catalyst 8510 software image on a LightStream 1010 switch to support L3-ATM (through the
ATM router module). However, the LightStream 1010 switch software image does not include support for the ATM
router module.
21. LDP = Label Distribution Protocol
22. LSR = label switch router
Release Names, Versions, and Part Numbers
Table 4 lists the release names, versions, and part numbers used with the Catalyst 8510 MSR and
LightStream 1010 switch. Platform-specific information is noted in the table.
Table 4
Release Name to Version to Part Number Matrix for Catalyst 8510 MSR and
LightStream 1010
Release Name
Release Version
Part Number
W5
12.1(5)EY1
Catalyst 8510 MSR: S851R2-12105EY
LightStream 1010: SL10R2-12105EY
W6
12.1(6)EY
Catalyst 8510 MSR: S851R2-12106EY
LightStream 1010: SL10R2-12106EY
W7a
12.1(7a)EY
Catalyst 8510 MSR: S851R2-12107EY
LightStream 1010: SL10R2-12107EY
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
9
System Requirements
Table 4
10
Release Name to Version to Part Number Matrix for Catalyst 8510 MSR and
LightStream 1010 (continued)
Release Name
Release Version
Part Number
W7a
12.1(7a)EY1
Catalyst 8510 MSR: S851R2-12107EY
LightStream 1010: SL10R2-12107EY
10E
12.1(10)E
Catalyst 8510 MSR: S851R2-12110E
LightStream 1010: SLSR2-12110E
10EY
12.1(10)EY
Catalyst 8510 MSR: S851R2-12110EY
LightStream 1010: SLSR2-12110EY
11bE
12.1(11)E
Catalyst 8510 MSR: S851R2-12111E
LightStream 1010: SLSR2-12111E
11bE1
12.1(11)E1
Catalyst 8510 MSR: S851R2-12111E1
LightStream 1010: SLSR2-12111E1
12cE
12.1(12c)E
Catalyst 8510 MSR: S851R2-12112E
LightStream 1010: SLSR2-12112E
12cE1
12.1(12c)E1
Catalyst 8510 MSR: S851R2-12112E1
LightStream 1010: SLSR2-12112E1
12cEY
12.1(12c)EY
Catalyst 8510 MSR: S851R2-12112EY
LightStream 1010: SLSR2-12112EY
13E1
12.1(13)E1
Catalyst 8510 MSR: S851R2-12113E1
LightStream 1010: SLSR2-12113E1
13EB1
12.1(13)EB1
Catalyst 8510 MSR: S851R2-12113EB1
LightStream 1010: SLSR2-12113E1B
14E1
12.1(14)E1
Catalyst 8510 MSR: S851R2-12114E1
LightStream 1010: SLSR2-12114E1
14EB
12.1(14)EB
Catalyst 8510 MSR: S851R2-12114EB
LightStream 1010: SLSR2-12114EB
19E
12.1(19)E
Catalyst 8510 MSR: S851R2-12119E
LightStream 1010: SLSR2-12119E
14EB1
12.1(14)EB1
Catalyst 8510 MSR: S851R2-12114EB1
LightStream 1010: SLSR2-12114EB1
19E2
12.1(19)E2
Catalyst 8510 MSR: S851R2-12119E2
LightStream 1010: SLSR2-12119E2
20E
12.1(20)E
Catalyst 8510 MSR: S851R2-12120E
LightStream 1010: SLSR2-12120E
20EB
12.1(20)EB
Catalyst 8510 MSR: S851R2-12120EB
LightStream 1010: SLSR2-12120EB
22E
12.1(22)E
Catalyst 8510 MSR: S851R2-12122E
LightStream 1010: SLSR2-12122E
22EB
12.1(22)EB
Catalyst 8510 MSR: S851R2-12122EB
LightStream 1010: SLSR2-12122EB
23EB
12.1(23)EB
Catalyst 8510 MSR: S851R2-12123EB
LightStream 1010: SLSR2-12123EB
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
New and Changed Information
Table 4
Release Name to Version to Part Number Matrix for Catalyst 8510 MSR and
LightStream 1010 (continued)
Release Name
Release Version
Part Number
26EB
12.1(26)EB
Catalyst 8510 MSR: S851R2-12126EB
LightStream 1010: SLSR2-12126EB
26EB1
12.1(26)EB1
Catalyst 8510 MSR: S851R2-12126EB1
LightStream 1010: SLSR2-12126EB1
New and Changed Information
This section includes new features that appear in this and previous releases of Cisco IOS Release 12.1
software. The new features are sorted by release number.
New Features in Release 12.1(26)EB2
Catalyst 8510 MSR
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)EB2.
New Features in Release 12.1(26)EB1
Catalyst 8510 MSR
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)EB1.
New Features in Release 12.1(26)EB
Catalyst 8510 MSR
The following new features are available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)EB:
•
Access Filters for SPVC Passive Soft Connections
•
SPVC Back-up Address support
•
Timer Rules based SPVC/SPVP
New Features in Release 12.1(23)EB
Catalyst 8510 MSR and LightStream 1010
The following new features are available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(23)EB:
•
Configuring Point-to-Multipoint CES Soft PVC Connections
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
11
New and Changed Information
•
Enabling and Disabling Roots and Leaves of Point-to-Multipoint Soft PVC Connections
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(23)EB.
New Features in Release 12.1(22)EB
Catalyst 8510 MSR and LightStream 1010
The following new features are available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(22)EB:
•
Explicit paths on CES VCs
•
Redundant soft-PVC and soft-PVP destinations
•
ATM Forum CES MIB support
•
Pass along bit support for ATM signaling messages
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(22)EB.
New Features in Release 12.1(22)E
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(22)E.
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(22)E.
New Features in Release 12.1(20)EB
Catalyst 8510 MSR and LightStream 1010
The following new feature is available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(20)EB:
•
SSH version 2 client
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(20)EB.
12
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
New and Changed Information
New Features in Release 12.1(20)E
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(20)E.
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(20)E.
New Features in Release 12.1(19)EB
Catalyst 8510 MSR and LightStream 1010
The following new feature is available for the Catalyst 8510 MSR and LightStream 1010 switch routers
in Cisco IOS Release 12.1(19)EB:
•
SSH server version 2
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(19)EB.
New Features in Release 12.1(19)E2
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(19)E2.
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(19)E2.
New Features in Release 12.1(14)EB1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(14)EB1.
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
13
New and Changed Information
New Features in Release 12.1(19)E
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(19)E.
New Features in Release 12.1(14)EB
Catalyst 8510 MSR and LightStream 1010
The following new features are available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(14)EB:
•
RFC1406 enhancements for CES provides SNMP support for:
– Read and write access to CES interface related objects using dsx1ConfigTable (CSCdv46424)
– Read access to DS0 time slot or slots using dsx1FracTable (CSCin18227)
– Read access to NSAP address configuration of the circuit using ciscoAtmIfSoftVcDestAddress
of CISCO-ATM-IF-MIB (CSCdz32265)
New Features in Release 12.1(14)E1
Catalyst 8510 MSR and LightStream 1010
The following new feature is available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(14)E1:
•
SNMP support for ARM subinterface
New Features in Release 12.1(13)EB1
Catalyst 8510 MSR and LightStream 1010
The following new features are available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(13)EB1:
14
•
Point-to-Multipoint Soft PVCs
•
Overflow queuing for VBR-nrt on Frame Relay interface modules
•
Configuring Frame Relay frame size for Frame Relay-ATM interworking
•
Configuring service class overbooking
•
Soft-PVC support on ATM 0 interface
•
RFC-2515 support
•
Traffic parameter modification for soft VCs and Soft VPs
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
New and Changed Information
New Features in Release 12.1(13)E1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(13)E1.
New Features in Release 12.1(12c)EY
Catalyst 8510 MSR and LightStream 1010
The following new features are available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(12c)EY:
•
SSH (Secure Shell)
•
Circuit Emulation Services (CES) switched VCs
•
SNMP version 3
New Features in Release 12.1(12c)E1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(12c)E1.
New Features in Release 12.1(12c)E
Catalyst 8510 MSR and LightStream 1010
The following new feature is available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(12c)E:
•
SNMP provisioning of ATM interface event traps to an SNMP host
•
Traffic shaping on well-known VCs
New Features in Release 12.1(11b)E1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(11b)E1.
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
15
New and Changed Information
New Features in Release 12.1(11b)E
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(11b)E.
New Features in Release 12.1(10)EY
Catalyst 8510 MSR and LightStream 1010
The following features are available for the Catalyst 8510 MSR and LightStream 1010 switch routers in
Cisco IOS Release 12.1(10)EY:
•
MPLS LDP (Label Distribution Protocol) support for both LSR (label switch router) and LER
•
MPLS LER on the 10/100BASE-TX, 100BASE-FX interface modules
•
Frame Relay PVCs terminated on ATM router module
•
SONET MIB (RFC 2558)
•
Two ended soft VC configuration
•
PNNI connection trace
New Features in Release 12.1(10)E
Catalyst 8510 MSR and LightStream 1010
The following features are available for the Catalyst 8510 MSR and LightStream 1010 switch routers in
Cisco IOS Release 12.1(10)E:
•
Priority soft PVC preservation on IMA bandwidth reduction
•
Standard signalling for Frame Relay soft PVCs
•
ATM threshold group enhancements
New Features in Release 12.1(7a)EY1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(7a)EY1.
16
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
Caveats
New Features in Cisco IOS Release 12.1(7a)EY
Catalyst 8510 MSR and LightStream 1010
The following features are available for the Catalyst 8510 and LightStream 1010 switch routers in Cisco
IOS Release 12.1(7a)EY:
•
VBR on ATM router module support
•
Shaped tunnel support for ATM router module
•
Rate limiting
•
Traffic-Shaping Carrier Module (TSCAM)
•
ADP
•
Radius support (TACACS+-like authentication)
New Features in Cisco IOS Release 12.1(6)EY
Catalyst 8510 MSR and LightStream 1010
The following new feature is available for the Catalyst 8510 MSR and LightStream 1010 switch routers
in Cisco IOS Release 12.1(6)EY:
•
ITT enhancements
New Features in Cisco IOS Release 12.1(5)EY1
Catalyst 8510 MSR and LightStream 1010
The following new feature is available for the Catalyst 8510 MSR and the LightStream 1010 switch in
Cisco IOS Release 12.1(5)EY1.
•
Power-on-diagnostics
Caveats
Caveats describe unexpected behavior or defects in Cisco IOS software releases. Caveats use a tracking
number (DDTS number) and the release number to maintain the database information. For a list of the
caveats and their status for the Cisco IOS Release for the Catalyst 8510 and the
LightStream 1010 switch, see the document, Release Notes for the Catalyst 8510 and the
LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB1, Part 2: Caveats.
Restriction
This section describes the following Catalyst 8510 MSR and the LightStream 1010 switch restriction:
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
17
Interoperability
Unicast Reverse Path Forwarding Not Supported
The Catalyst 8510 MSR and the LightStream 1010 switches do not support Unicast Reverse Path
Forwarding (uRPF).
Interoperability
Starting with Cisco IOS Release 12.0(10)W5(18b) software release, hardware and software functionality
interoperability exists between CSR interface modules and MSR interface modules by way of the ATM
router module on the MSR chassis running an MSR image.
Y2K Compliance
Catalyst 8510 and LightStream 1010 systems running Cisco IOS Release 12.0(0.6)W5(1) or later have
been certified as Y2K compliant. For more information, see the following URL:
http://www.cisco.com/warp/public/752/2000/.
Related Documentation
•
Regulatory Compliance and Safety Information for the Catalyst 8500 and LightStream 1010 Series
•
Site Preparation
•
Quick Reference Catalyst 8510 and LightStream 1010 Hardware Information
•
ATM and Layer 3 Module Installation Guide
•
Guide to ATM Technology
•
ATM and Layer 3 Quick Software Configuration Guide
•
ATM and Layer 3 Switch Router Command Reference
•
ATM Switch Router Software Configuration Guide
•
Layer 3 Software Feature and Configuration Guide
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
18
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
Documentation Feedback
You can access the Cisco website at this URL:
http://www.cisco.com
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
•
Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from
the Ordering tool:
http://www.cisco.com/en/US/partner/ordering/index.shtml
•
Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in
North America, by calling 800 553-NETS (6387).
Documentation Feedback
You can send comments about technical documentation to [email protected].
You can submit comments by using the response card (if present) behind the front cover of your
document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco
Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical
Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical
Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service
contract, contact your reseller.
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
19
Obtaining Technical Assistance
Cisco Technical Support Website
The Cisco Technical Support Website provides online documents and tools for troubleshooting and
resolving technical issues with Cisco products and technologies. The website is available 24 hours a day,
365 days a year at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password.
If you have a valid service contract but do not have a user ID or password, you can register at this URL:
http://tools.cisco.com/RPF/register/register.do
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3
and S4 service requests are those in which your network is minimally impaired or for which you require
product information.) After you describe your situation, the TAC Service Request Tool automatically
provides recommended solutions. If your issue is not resolved using the recommended resources, your
service request will be assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at
this URL:
http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone.
(S1 or S2 service requests are those in which your production network is down or severely degraded.)
Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business
operations running smoothly.
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553 2447
For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity
definitions.
Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You
and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco
will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3)—Operational performance of your network is impaired, but most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
20
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
Obtaining Additional Publications and Information
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
•
Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit
Cisco Marketplace, the company store, at this URL:
http://www.cisco.com/go/marketplace/
•
The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as
ordering and customer support services. Access the Cisco Product Catalog at this URL:
http://cisco.com/univercd/cc/td/doc/pcat/
•
Cisco Press publishes a wide range of general networking, training and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press at this URL:
http://www.ciscopress.com
•
Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and
networking investments. Each quarter, Packet delivers coverage of the latest industry trends,
technology breakthroughs, and Cisco products and solutions, as well as network deployment and
troubleshooting tips, configuration examples, customer case studies, certification and training
information, and links to scores of in-depth online resources. You can access Packet magazine at this
URL:
http://www.cisco.com/packet
•
iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies
learn how they can use technology to increase revenue, streamline their business, and expand
services. The publication identifies the challenges facing these companies and the technologies to
help solve them, using real-world case studies and business strategies to help readers make sound
technology investment decisions. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
•
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
•
World-class networking training is available from Cisco. You can view current offerings at
this URL:
http://www.cisco.com/en/US/learning/index.html
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
CCSP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work,
Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA,
CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems
Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast
Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard,
LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing,
Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase
Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain
other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0411R)
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01
21
Obtaining Additional Publications and Information
Copyright © 2005 Cisco Systems, Inc. All rights reserved.
22
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)EB2, Part 1: System Requirements
OL-14426-01