Release Notes for the Catalyst 8510 and the
LightStream 1010 Switch for Cisco IOS
Release 12.1(26)E8, Part 1: System Requirements
August 08, 2007
Catalyst 8510 and LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8
Text Part Number: OL-14457-01
This document describes the features and caveats for Cisco IOS Release 12.1(26)E8 software for the
Catalyst 8510 and the LightStream 1010 switch.
Note
All information pertains to both the Catalyst 8510 and LightStream 1010 switch platforms, unless
differences between the platforms are noted in the text.
Contents
This document includes the following sections:
•
Introduction, page 2
•
System Requirements, page 2
•
Upgrade and Downgrade Notes, page 22
•
New and Changed Information, page 23
•
Caveats, page 29
•
Restriction, page 30
•
Interoperability, page 30
•
Y2K Compliance, page 30
•
Related Documentation, page 30
•
Obtaining Documentation, page 31
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2007 Cisco Systems, Inc. All rights reserved.
Introduction
•
Obtaining Technical Assistance, page 32
•
Obtaining Additional Publications and Information, page 33
Introduction
The Catalyst 8510 and LightStream 1010 switch provide switched ATM connections to individual
workstations, servers, LAN segments, or other ATM switches and routers using fiber-optic, unshielded
twisted-pair (UTP), and coaxial cable.
Note
The ATM switch processors (hardware version 4.0 or higher) and all port adapters can be installed in the
Catalyst 5500 switch chassis.
The Catalyst 8510 CSR belongs to a class of high-performance Layer 3 switch routers. It is optimized
for the campus LAN or the intranet and provides both wirespeed Ethernet routing and switching services.
System Requirements
This section describes the system requirements for Cisco IOS Release 12.1 and includes the following
sections:
•
Memory Requirements, page 2
•
Hardware Supported, page 3
•
Determining Your Software Release, page 5
•
Other Firmware Code, page 5
•
Feature Set Tables, page 5
•
Release Names, Versions, and Part Numbers, page 20
Memory Requirements
Catalyst 8510 MSR and LightStream 1010
The DRAM memory configuration is 64-MB DRAM (MEM-ASP64M), which is the default for both the
Catalyst 8510 and the LightStream 1010 switch platforms.
Catalyst 8510 CSR
Table 1 lists the default Flash and DRAM memory for the Catalyst 8510 CSR, as well as memory
upgrade options.
2
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
System Requirements
Table 1
Catalyst 8510 CSR Default Memory and Upgrade Options
Memory Type
Catalyst 8510 CSR Defaults Upgrade Options
Flash memory 16 MB
MEM-ASP-FLC16M=
MEM-ASP-FLC20M=
DRAM
None
64 MB
To download and store a copy of the Catalyst 8510 CSR software image, we recommend using a
minimum 20 MB Flash PC Card, which will allow you to have two or more images installed at the same
time.
The Catalyst 8510 CSR boots from its onboard Flash memory by default. To change this default to boot
from a Flash PC Card instead, you must change the configuration register setting to 0x2102. Refer to the
Layer 3 Switching Software Feature and Configuration Guide for more information.
Hardware Supported
Table 2 lists the interfaces supported by both the Catalyst 8510 MSR and LightStream 1010 switch and
Cisco IOS Release 12.1(26)E8 and their minimum software release requirements. All platform specific
requirements are noted in the table. Table 2 lists this information for the Catalyst 8510 CSR.
Note
Although minimum software versions are listed, we strongly recommend that you use the
latest available software release for all Catalyst 8510 and LightStream 1010 hardware.
Table 2
Catalyst 8510 MSR and LightStream 1010 Interface Modules and
Minimum Software Required
Part Number
Description
Minimum Software
Version Required
WAI-OC3-4MM
4-port STS-3c/STM-1 multimode fiber port adapters
WAS1-1
WAI-OC3-4SS
4-port STS-3c/STM-1 single-mode fiber port adapters WAS1-1
WAI-OC3-4U5
4-port STS-3c/STM-1 UTP-5 port adapters
WAS1-1
WAI-OC3-4SSLR
4-port STS-3c/STM-1 SMF long reach port adapters
WAS3-2
WAI-OC3-1S3M
OC-3 mix port adapter module, 1 IR+ port and 3 MM WAS3-1
ports
WAI-OC12-1MM
1-port STS-12c/STM-4c multimode fiber port adapters WAS1-2
WAI-OC12-1SS
1-port STS-12c/STM-4c SMF port adapters
WAI-OC12-1SSLR
1-port STS-12c/STM-4c SMF long reach port adapters WAS3-2
WAI-ATM25-12P
12-port ATM 25 port adapters with 96-pin telco cable WAS3-2
WAI-T3-2BNC
2-port DS-3 port adapters
WAS1-1
WAI-E3-2BNC
2-port E3 port adapters
WAS1-1
WAI-T3-4BNC
4-port DS-3 port adapters
WAS3-1
WAI-E3-4BNC
4-port E3 port adapters
WAS3-3
WAI-T1-4RJ48
4-port T1 (ATM) with RJ-48 interface port adapters
WAS3-1
WAS1-1
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
3
System Requirements
Table 2
Catalyst 8510 MSR and LightStream 1010 Interface Modules and
Minimum Software Required (continued)
Part Number
Description
Minimum Software
Version Required
WAI-E1-4RJ48
4-port E1 (ATM) with RJ-48 interface port adapters
WAS3-1
WAI-E1-4BNC
4-port E1 (ATM) with BNC interface port adapters
WAS3-1
WAI-T1C-4RJ48
4-port T1 (circuit emulation) with RJ-48 interface port WAS3-1
adapters
WAI-E1C-4RJ48
4-port E1 (circuit emulation) with RJ-48 interface port WAS3-1
adapters
WAI-E1C-4BNC
4-port E1 (circuit emulation) with BNC interface port WAS3-1
adapters
L1010-PWR-DC
Power supply DC
L1010-ASP-B-FC1
WAS3-1
1
2
ASP with FC-per-class queuing (FC-PCQ )
1
WAS1-3
L1010-ASP-B-FCPFQ ASP with FC-per-flow queuing (FC-PFQ )
WAS4-1
L1010-ASP-C-FC1
W5-5
Hot-swappable ASP with FC-PCQ
L1010-ASP-C-FCPFQ Hot-swappable multiservice switch route processor
W5-5
C85MS-4E1-FRRJ48
4-port CE1 with RJ-48c interface Frame Relay port
adapters
W5-5
WS-X5165
ATM-Fabric Integration Module for the Catalyst 5500 W5-5
C85MS-1DS3-FRBNC 1-port CDS3 Frame Relay port adapter
W5-9
C85MS-ATM25-4P
W5-9
C85MS-8T1-IMA
4
3
4-port 25-Mbps port adapter
8-port T1 port adapter with IMA
4
Catalyst 8510
S851R2-12.0.4W
LightStream 1010
SL10R2-12.0.4W
C85MS-8E1-IMA-120 8-port E1 port adapter with IMA
Catalyst 8510
S851R2-12.0.4W
LightStream 1010
SL10R2-12.0.4W
C8510-ARM-64K
ATM router module
S851R2-12.0.10W5
C8510-ACL
ACL6 daughter card
S851R2-12.0.10W5
C85GE-1X-16K=
1-port Gigabit Ethernet 16K
S851R2-12.0.10W5
C85GE-1X-64K=
1-port Gigabit Ethernet 64K
S851R2-12.0.10W5
C85FE-8T-16K=
8-port 10/100 Fast Ethernet with RJ-45 16K
S851R2-12.0.10W5
C85FE-8T-64K=
8-port 10/100 Fast Ethernet with RJ-45 64K
S851R2-12.0.10W5
C85FE-8F-16K=
8-port 10/100 Fast Ethernet with MT-RJ 16K
S851R2-12.0.10W5
C85FE-8F-64K=
8-port 10/100 Fast Ethernet with MT-RJ 64K
S851R2-12.0.10W5
C8510-TSCAM-2P
Traffic-Shaping Carrier Module (TSCAM)
Catalyst 8510
MSR:
S851R2-12107EY
LightStream 1010:
SL10R2-12107EY
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
System Requirements
1. ASP = ATM switch processor.
2. FC-PCQ = feature card per-class queuing.
3. FC-PFQ = feature card per-flow queuing.
4. IMA = inverse multiplexing over ATM.
5. The LightStream 1010 switch requires the ASP-C with FC-PFQ to support the ATM router module.
6. ACL = access control list.
Determining Your Software Release
To determine the version of Cisco IOS software currently running on either the Catalyst 8510 or the
LightStream 1010 switch, log in to the switch and enter the show version EXEC command. The
following is sample output from the show version command. The version number is indicated on the
second line as shown:
Cisco Internetwork Operating System Software
IOS (tm) LS1010 W5-5 Software (LS1010-WP-M), Version 12.1(26)E8
Additional command output lines include more information, such as processor revision numbers,
memory amounts, hardware IDs, and partition information.
Other Firmware Code
Some of the port adapters supported on the Catalyst 8510 and LightStream 1010 switch have
upgradeable FPGA and functional images. The FPGA and functional images include caveat fixes, but in
most cases, it is not necessary to upgrade. The release notes that describe the caveats from the FPGA
and functional images are available on the World Wide Web at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/l3sw/8540/rel_12_0/w5_6f/rel_note/fpga_rn/ind
ex.htm
For information describing the firmware update process, refer to the section “Maintaining Functional
Images (Catalyst 8510 and LightStream 1010)” in the chapter “Managing Configuration Files, System
Images, and Functional Images” in the ATM Switch Router Software Configuration Guide.
Feature Set Tables
The Cisco IOS release software is packaged in feature sets (also called software images) depending on
the platform. Each feature set contains a specific set of Cisco IOS features. Table 3 lists the Cisco IOS
software feature sets available for the Catalyst 8510 MSR and LightStream 1010 switch in Cisco IOS
Release 12.1(26)E8.
Note
All Catalyst 8510 CSR features are also applicable to Catalyst 8510 MSR.
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
5
System Requirements
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch
12. 1(26)E8
Table 3
Left-just X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ified
E.164
AFI sup
port
SNMP1
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Asynchr
onous
support
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
PPP2
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
(SLIP3/P
PP)
IP4
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
NTP
5
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
TACAC
S+6
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Telnet
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Point-to- X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
point
and
point-tomultipoi
nt
permane
nt
VCCs7
and
VPCs8
Point-to- X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
point
and
point-tomultipoi
nt
switched
VCCs
and
VPCs
(UNI
3.0)
6
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
System Requirements
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12. 1(26)E8
Table 3
Point-to- X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
point
and
point-tomultipoi
nt
switched
VCCs
and
VPCs
(UNI
3.1)
Point-to- X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
point
and
point-tomultipoi
nt
switched
VCCs
and
VPCs
(UNI
4.0)
Multipoi X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
nt-to-poi
nt UNI
signalin
g
Soft
VCCs
and
VPCs
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
VP
tunnelin
g
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
VPI/VCI X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
range
support
in ILMI
4.0
PNNI
hierarch
y
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
7
System Requirements
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12. 1(26)E8
Table 3
ILMI
version
4.0
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
IISP9
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
10
LANE
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
client
(LEC11)
and
LANE
Services
(LES12/
BUS13/L
ECS14)
on ASP
15
Token
Ring
LANE
services
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ATM
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ARP16
server on
ASP
ATM
ARP
client on
ASP
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ATM tag X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
switch
router
(TSR)
Port
snoopin
g
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
OAM17
F4 and
F5
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
E.164
address
translati
on
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
8
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
System Requirements
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12. 1(26)E8
Table 3
E.164
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
autoconv
ersion
Circuit
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
emulatio
n
ATM
access
lists
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ATM
accounti
ng
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ATM
RMON
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
18
Multiple X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
,
weighte
d,
dynamic
threshol
ds for
selective
packet
marking
and
discard
Shaped
VP
tunnels
for CBR
traffic
(FC-PF
Q only)
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
9
System Requirements
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12. 1(26)E8
Table 3
Substitut X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ion of
other
service
categori
es in
shaped
VP
tunnels
(FC-PF
Q
feature
cards
only)
Dual
leaky
bucket
policing
(FC-PF
Q
feature
cards
only)
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Schedul X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
er/Servic
e
Class/P
VC
configur
ation for
FC-PFQ
feature
cards
10
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
Feature
Set
12.1(26)E5
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12.1(26)E7
Table 3
12. 1(26)E8
System Requirements
Logical X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
multicas
t support
(up to
254
leaves
per
output
port, per
point-tomultipoi
nt VC)
(FC-PF
Q
feature
cards
only)
Network X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
clocking
enhance
ments
for
smooth
switchov
er
(FC-PF
Q
feature
cards
only)
Per-VC X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
or
per-VP
nondisru
ptive
snoopin
g
(FC-PF
Q
feature
cards
only)
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
11
System Requirements
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12. 1(26)E8
Table 3
Support X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
for
non-zero
MCR19
on ABR
connecti
ons
(FC-PF
Q
feature
cards
only)
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Access
lists on
ILMI
registrati
on
CUGs
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ATM
soft
restart
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ATM
accounti
ng
enhance
ments
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
CISCOSYSLO
G-MIB
support
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
CISCOCONFI
G-COP
Y-MIB
support
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Signalin
g
diagnost
ics and
MIB
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
12
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
System Requirements
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12. 1(26)E8
Table 3
Supplem X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ental
AToM
MIB
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Frame
Relay to
ATM
Interwor
king
Features
on the
Channeli
zed E1
Port
Adapter
Hierarch X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
ical VP
Tunnels
Remote
logging
for
accounti
ng
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Tag
Switchin
g
VC-Mer
ge on
Non-UB
R VP
Tunnels
and
Hierarch
ical VP
Tunnels
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
PNNI
Complex
Node
Represe
ntation
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
13
System Requirements
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12. 1(26)E8
Table 3
Support
for
ATM-Fa
bric
Integrati
on
Module
in
Catalyst
5500
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
PNNI
explicit
paths
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
PNNI
alternate
link
selection
Tag
switchin
g CoS
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Network X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Clock
Distribut
ion
Protocol
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Simple
Gateway
Control
Protocol
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Inverse
Multiple
xing
over
ATM
(IMA)
groups
ATM
End
System
Address
(AESA)
gateway
14
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
System Requirements
ATM
overboo
king
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12. 1(26)E8
Table 3
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Framing X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
overhead
NCDP
MIB
Support
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
L3-ATM
routing
and
bridging
via RFC
1483
(ATM
router
module)
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
20
Point-topoint
subinterf
aces,
only
point-tomultipoi
nt
subinterf
aces are
supporte
d
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Power-o X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
n-diagno
stics
ITT
Enhance
ments
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
VBR on
ATM
router
module
support
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
15
System Requirements
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Shaped
Tunnel
Support
for ATM
router
module
Rate
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Limiting
CiscoVi
ew
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
Radius
Support
(TACAC
S+-like
authenti
cation)
Priority X X X X X X X X X X X X X X X X X X X X X X X X X X X
Soft
PVC
Preserva
tion on
IMA
Bandwid
th
Reductio
n
Standard X X X X X X X X X X X X X X X X X X X X X X X X X X X
Signalin
g for
Frame
Relay
Soft
PVCs
X X X X X X X X X X X X X X X X X X X X X X X X X X X
ATM
Threshol
d Group
Enhance
ments
MPLS
LDP21
support
for
LSR22
16
X X X X X X X X X X X X X X X X X X X X X X X X X X
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12. 1(26)E8
Table 3
System Requirements
Frame
Relay
PVCs
terminat
ed on
ATM
router
module
X X X X X X X X X X X X X X X X X X X X X X X X X X
SONET
MIB
(RFC
2558)
X X X X X X X X X X X X X X X X X X X X X X X X X X
X X X X X X X X X X X X X X X X X X X X X X X X X X
Two
Ended
Soft VC
Configur
ation
PNNI
X X X X X X X X X X X X X X X X X X X X X X X X X X
Connecti
on Trace
X X X X X X X X X X X X X X X X X X X X X X X
SNMP
provisio
ning of
ATM
interface
traps to
an
SNMP
Host
X X X X X X X X X X X X X X X X X X X X X X X
Traffic
shaping
on
well-kno
w VCs
SSH
(Secure
Shell)
X X X X X X X X X X X X X X X X X X X X X
CES
X X X X X X X X X X X X X X X X X X X X X
switched
VCs
SNMP
Version
3
X X X X X X X X X X X X X X X X X X X X X
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
17
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
12.1(26)E5
12.1(26)E7
Feature
Set
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12. 1(26)E8
Table 3
Point-toMultipoi
nt Soft
PVCs
X
X
X
Overflo
w
Queuing
for
VBR-nrt
on
Frame
Relay
interface
modules
X
X
X
Configur
ing
Frame
Relay
frame
size for
Frame
Relay-A
TM
interwor
king
X
X
X
Soft-PV
C
support
on ATM
0
interface
X
X
X
RFC-25
15
support
X
X
X
Traffic
paramet
er
modifica
tion for
Soft VCs
and Soft
VPs
X
X
X
18
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
Feature
Set
12.1(26)E5
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12.1(26)E7
Table 3
12. 1(26)E8
System Requirements
SNMP
support
for ARM
sub
interface
12.1(5)EY1
12.1(6)EY
12.1(7a)EY
12.1(7a)EY1
12.1(10)E
12.1(10)EY
12.1(11b)E
12.1(11b)E1
12.1(12c)E
12.1(12c)E1
12.1(12c)EY
12.1(13)E1
12.1(13)EB1
12.1(14)E1
12.1(14)EB
12.1(19)E
12.1(14)EB1
12.1(19)E2
12.1(20)E
12.1(20)EB1
12.1(22)E
12.1(23)E
12.1(23)E1
12.1(26)E
12.1(26)E1
12.1(26)E2
12.1(26)E3
12.1(26)E4
Feature
Set
12.1(26)E5
Feature Sets Supported by the Catalyst 8510 MSR and LightStream 1010 Switch (continued)
12.1(26)E7
Table 3
12. 1(26)E8
System Requirements
X X X X X X X X X X X X
CES
MIB
X
SSH
Server
Version
2
X
LANE
with
Jumbo
Frames
on
enhance
d ATM
router
module
X
X
1. SNMP = Simple Network Management Protocol.
2. PPP = Point-to-Point Protocol.
3. SLIP = Serial Line Internet Protocol.
4. IP = Internet Protocol.
5. NTP = Network Time Protocol.
6. TACACS+ = Terminal Access Controller Access Control System Plus.
7. VCCs = virtual channel connections.
8. VPCs = virtual path connections.
9. IISP = Interim-Interswitch Signaling Protocol.
10. LANE = LAN emulation.
11. LEC = LAN emulation client.
12. LES = LAN emulation server.
13. BUS = broadcast and unknown server.
14. LECS = LAN emulation configuration server.
15. ASP = ATM switch processor.
16. ARP = Address Resolution Protocol.
17. OAM = Operation, Administration, and Maintenance.
18. RMON = Remote Monitoring.
19. MCR = minimum cell rate.
20. You can download the Catalyst 8510 software image on a LightStream 1010 switch to support L3-ATM (through the ATM router module). However, the
LightStream 1010 switch software image does not include support for the ATM router module.
21. LDP = Label Distribution Protocol
22. LSR = label switch router
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
19
System Requirements
Release Names, Versions, and Part Numbers
Table 4 lists the release names, versions, and part numbers used with the Catalyst 8510 MSR and
LightStream 1010 switch. Platform-specific information is noted in the table.
Table 4
20
Release Name to Version to Part Number Matrix for Catalyst 8510 MSR and
LightStream 1010
Release Name
Release Version
Part Number
W5
12.1(5)EY1
Catalyst 8510 MSR: S851R2-12105EY
LightStream 1010: SL10R2-12105EY
W6
12.1(6)EY
Catalyst 8510 MSR: S851R2-12106EY
LightStream 1010: SL10R2-12106EY
W7a
12.1(7a)EY
Catalyst 8510 MSR: S851R2-12107EY
LightStream 1010: SL10R2-12107EY
W7a
12.1(7a)EY1
Catalyst 8510 MSR: S851R2-12107EY
LightStream 1010: SL10R2-12107EY
10E
12.1(10)E
Catalyst 8510 MSR: S851R2-12110E
LightStream 1010: SLSR2-12110E
10EY
12.1(10)EY
Catalyst 8510 MSR: S851R2-12110EY
LightStream 1010: SLSR2-12110EY
11bE
12.1(11)E
Catalyst 8510 MSR: S851R2-12111E
LightStream 1010: SLSR2-12111E
11bE1
12.1(11)E1
Catalyst 8510 MSR: S851R2-12111E1
LightStream 1010: SLSR2-12111E1
12cE
12.1(12c)E
Catalyst 8510 MSR: S851R2-12112E
LightStream 1010: SLSR2-12112E
12cE1
12.1(12c)E1
Catalyst 8510 MSR: S851R2-12112E1
LightStream 1010: SLSR2-12112E1
12cEY
12.1(12c)EY
Catalyst 8510 MSR: S851R2-12112EY
LightStream 1010: SLSR2-12112EY
13E1
12.1(13)E1
Catalyst 8510 MSR: S851R2-12113E1
LightStream 1010: SLSR2-12113E1
13EB1
12.1(13)EB1
Catalyst 8510 MSR: S851R2-12113EB1
LightStream 1010: SLSR2-12113E1B
14E1
12.1(14)E1
Catalyst 8510 MSR: S851R2-12114E1
LightStream 1010: SLSR2-12114E1
14EB
12.1(14)EB
Catalyst 8510 MSR: S851R2-12114EB
LightStream 1010: SLSR2-12114EB
19E
12.1(19)E
Catalyst 8510 MSR: S851R2-12119E
LightStream 1010: SLSR2-12119E
14EB1
12.1(14)EB1
Catalyst 8510 MSR: S851R2-12114EB1
LightStream 1010: SLSR2-12114EB1
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
System Requirements
Table 4
Release Name to Version to Part Number Matrix for Catalyst 8510 MSR and
LightStream 1010 (continued)
Release Name
Release Version
Part Number
19E2
12.1(19)E2
Catalyst 8510 MSR: S851R2-12119E2
LightStream 1010: SLSR2-12119E2
20E
12.1(20)E
Catalyst 8510 MSR: S851R2-12120E
LightStream 1010: SLSR2-12120E
20EB
12.1(20)EB
Catalyst 8510 MSR: S851R2-12120EB
LightStream 1010: SLSR2-12120EB
22E
12.1(22)E
Catalyst 8510 MSR: S851R2-12122E
LightStream 1010: SLSR2-12122E
23E
12.1(23)E
Catalyst 8510 MSR: S851R2-12123E
LightStream 1010: SLSR2-12123E
23E1
12.1(23)E1
Catalyst 8510 MSR: S851R2-12123E1
LightStream 1010: SLSR2-12123E1
26E
12.1(26)E
Catalyst 8510 MSR: S851R2-12126E
LightStream 1010: SLSR2-12126E
26E1
12.1(26)E1
Catalyst 8510 MSR: S851R2-12126E1
LightStream 1010: SLSR2-12126E1
26E2
12.1(26)E2
Catalyst 8510 MSR: S851R2-12126E2
LightStream 1010: SL10R2-12126E2
26E3
12.1(26)E3
Catalyst 8510 MSR: S851R2-12126E3
LightStream 1010: SL10R2-12126E3
26E4
12.1(26)E4
Catalyst 8510 MSR: S851R2-12126E4
LightStream 1010: SL10R2-12126E4
26E5
12.1(26)E5
Catalyst 8510 MSR: S851R2-12126E5
LightStream 1010: SL10R2-12126E5
26E7
12.1(26)E7
Catalyst 8510 MSR: S851R2-12126E7
LightStream 1010: SL10R2-12126E7
26E8
12.1(26)E8
Catalyst 8510 MSR: S851R2-12126E8
LightStream 1010: SL10R2-12126E8
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
21
Upgrade and Downgrade Notes
Upgrade and Downgrade Notes
Following are some issues which you should be aware of during upgrade or downgrade of the Cisco IOS
software for the Catalyst 8510 MSR:
Note
The procedure used to upgrade and downgrade a Catalyst 8540 MSR is available on the following:
http://www.cisco.com/warp/public/121/8540redundancy.shtml.
1.
When a Frame Relay connection traffic table row (CTTR) index is created using the CLI a
corresponding ATM CTTR is also created automatically by the switch and the MBS value (in the
internally created ATM CTTR) is calculated using the Bc value configured on the Frame Relay side.
However, the ATM CTTR can also be created using the CLI and then associated with a Frame Relay
CTTR. If you create the Frame Relay CTTR and associated it with the manually created ATM
CTTR, during an upgrade of Catalyst 8540 MSR from Cisco IOS release 12.1(12c)EY to the release
12.1(13)EB, manually created ATM CTTR association will not be in effect on the new primary
Route Processor (after switchover). Instead, an ATM CTTR (with random index) corresponding to
Frame Relay CTTR is recreated with an MBS value generated from the Bc value configured on the
Frame Relay side. This means, after upgrade, if manual association of ATM CTTR to Frame Relay
CTTR is required, it needs to be redone (by deleting the existing Frame Relay CTTR and then
recreating it with manual association of an ATM CTTR).
2.
When the Catalyst 8540 MSR is downgraded from release 12.1(13)EB to any lower version, ATM
CTTRs having packet-discard enabled and ATM VCs associated with CTTRs having packet-discard
enabled are lost. This is because, during an upgrade if release 12.1(13)EB is running on the primary
Route Processor and some lower version is running on the secondary Route Processor, the ATM
CTTR (having packet-discard enabled) information are not synced to the secondary Route
Processor. And if Route Processor switchover is done to complete the downgrade the ATM CTTRs
having packet-discard enabled are lost along with the ATM VCs associated with these ATM CTTRs.
3.
When the Catalyst 8540 MSR is downgraded from release 12.1(13)EB to any lower version (in the
12.1 train), Frame Relay CTTRs having non-default frame size and Frame Relay VCs associated
with Frame Relay CTTR having non-default frame size are lost. This is because, during an
downgrade if release 12.1(13)EB is running on the primary Route Processor and some lower version
is running on the secondary Route Processor, the Frame Relay CTTR (having non-default frame
size) information are not synced to the secondary Route Processor. And if Route Processor
switchover is done to complete the downgrade, Frame Relay CTTRs having non-default frame size
are lost along with the Frame Relay VCs associated with these Frame Relay CTTRs. However, the
Frame Relay VCs will not be removed from the firmware. But, traffic flow through those VCs
STOPS at the ATM leg (including that of psuedo port) is NOT present in the hardware for all Frame
Relay VCs after downgrade. To recover from this problem, use the hw-module slot/subslot reset
command and recreate the lost Frame Relay CTTRs and Frame Relay VCs.
4.
Frame Relay CTTR could be configured with Bc/Be less than Frame Size before release
12.1(13)EB. With release12.1(13)EB, Bc/Be can not be less than the Frame Relay frame size. Hence
if the Catalyst 8540 MSR, Catalyst 8510 MSR, or a LightStream 1010 is running an image older
than release 12.1(13)EB and if the startup configuration has the Bc/Be value less than 2000 bits (in
older images default frame size = 250 bytes = 2000 bits) and is reloaded and rebooted with release
12.1(13)EB, then the following error messages might appear for the primary Route Processor:
% Bc should be greater than Frame-size (in bits).
Any Frame Relay CTTR having Bc/Be less than Frame Size might be lost after reboot.
22
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
New and Changed Information
Also, Frame Relay VCs associated with these CTTRs might cause the following message to appear
when the primary Route Processor is coming up:
%FRATM-3-CONFIG_ERROR:
Note
Invalid rx-cttr
The Frame Relay VCs associated with these CTTRs might be lost after reboot.
New and Changed Information
This section includes new features that appear in this and previous releases of Cisco IOS release 12.1
software. The new features are sorted by release number.
New Features in Release 12.1(26)E8
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)E8.
New Features in Release 12.1(26)E7
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)E7.
New Features in Release 12.1(26)E5
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)E5.
New Features in Release 12.1(26)E4
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)E4.
New Features in Release 12.1(26)E3
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)E3.
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
23
New and Changed Information
New Features in Release 12.1(26)E2
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)E2.
New Features in Release 12.1(26)E1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)E1.
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(26)E1.
New Features in Release 12.1(26)E
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(26)E.
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(26)E.
New Features in Release 12.1(23)E1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(23)E1.
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(23)E1.
New Features in Release 12.1(23)E
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(23)E.
24
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
New and Changed Information
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(23)E.
New Features in Release 12.1(22)E
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(22)E.
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(22)E.
New Features in Release 12.1(20)EB
Catalyst 8510 MSR and LightStream 1010
The following new features are available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(20)EB:
•
SSH Server Version 2
•
LANE with Jumbo Frames on enhanced ATM router module
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(20)E.
New Features in Release 12.1(20)E
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(20)E.
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(20)E.
New Features in Release 12.1(19)E2
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(19)E2.
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
25
New and Changed Information
Catalyst 8510 CSR
There are no new features for the Catalyst 8510 CSR in Cisco IOS Release 12.1(19)E2.
New Features in Release 12.1(14)EB1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(14)EB1.
New Features in Release 12.1(19)E
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR in Cisco IOS Release 12.1(19)E.
New Features in Release 12.1(14)EB
Catalyst 8510 MSR and LightStream 1010
The following new features are available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(14)EB:
•
RFC1406 enhancements for CES-Provides SNMP support for:
– Read and write access to CES interface related objects using dsx1ConfigTable (CSCdv46424)
– Read access to DS0 time slot or slots using dsx1FracTable (CSCin18227)
– Read access to NSAP address configuration of the circuit using ciscoAtmIfSoftVcDestAddress
of CISCO-ATM-IF-MIB (CSCdz32265)
New Features in Release 12.1(14)E1
Catalyst 8510 MSR and LightStream 1010
The following new feature is available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(14)E1:
•
SNMP support for ARM sub interface
New Features in Release 12.1(13)EB1
Catalyst 8510 MSR and LightStream 1010
The following new features are available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(13)EB1:
•
26
Point-to-Multipoint Soft PVCs
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
New and Changed Information
•
Overflow Queuing for VBR-nrt on Frame Relay interface modules
•
Configuring Frame Relay frame size for Frame Relay-ATM interworking
•
Configuring Service Class Overbooking
•
Soft-PVC support on ATM 0 interface
•
RFC-2515 support
•
Traffic parameter modification for Soft VCs and Soft VPs
New Features in Release 12.1(13)E1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(13)E1.
New Features in Release 12.1(12c)EY
Catalyst 8510 MSR and LightStream 1010
The following new features are available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(12c)EY:
•
SSH (Secure Shell)
•
Circuit Emulation Services (CES) switched VCs
•
SNMP Version 3
New Features in Release 12.1(12c)E1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(12c)E1.
New Features in Release 12.1(12c)E
Catalyst 8510 MSR and LightStream 1010
The following new feature is available for the Catalyst 8510 MSR in Cisco IOS Release 12.1(12c)E:
•
SNMP provisioning of ATM interface event traps to an SNMP host
•
Traffic shaping on well-known VCs
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
27
New and Changed Information
New Features in Release 12.1(11b)E1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(11b)E1.
New Features in Release 12.1(11b)E
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(11b)E.
New Features in Release 12.1(10)EY
Catalyst 8510 MSR and LightStream 1010
The following features are available for the Catalyst 8510 MSR and LightStream 1010 switch routers in
Cisco IOS Release 12.1(10)EY:
•
MPLS LDP (Label Distribution Protocol) support for both LSR (label switch router) and LER
•
MPLS LER on the 10/100 Base-TX, 100 Base-FX interface modules
•
Frame Relay PVCs terminated on ATM router module
•
SONET MIB (RFC 2558)
•
Two Ended Soft VC Configuration
•
PNNI Connection Trace
New Features in Release 12.1(10)E
Catalyst 8510 MSR and LightStream 1010
The following features are available for the Catalyst 8510 MSR and LightStream 1010 switch routers in
Cisco IOS Release 12.1(10)E:
28
•
Priority Soft PVC Preservation on IMA Bandwidth Reduction
•
Standard Signalling for Frame Relay Soft PVCs
•
ATM Threshold Group Enhancements
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
Caveats
New Features in Release 12.1(7a)EY1
Catalyst 8510 MSR and LightStream 1010
There are no new features for the Catalyst 8510 MSR and LightStream 1010 switch routers in Cisco IOS
Release 12.1(7a)EY1.
New Features in Cisco IOS Release 12.1(7a)EY
Catalyst 8510 MSR and LightStream 1010
The following features are available for the Catalyst 8510 and LightStream 1010 switch routers in Cisco
IOS Release 12.1(7a)EY:
•
VBR on ATM router module support
•
Shaped Tunnel Support for ATM router module
•
Rate Limiting
•
Traffic-Shaping Carrier Module (TSCAM)
•
ADP
•
Radius Support (TACACS+-like authentication)
New Features in Cisco IOS Release 12.1(6)EY
Catalyst 8510 MSR and LightStream 1010
The following new feature is available for the Catalyst 8510 MSR and LightStream 1010 switch routers
in Cisco IOS Release 12.1(6)EY:
•
ITT Enhancements
New Features in Cisco IOS Release 12.1(5)EY1
Catalyst 8510 MSR and LightStream 1010
The following new feature is available for the Catalyst 8510 MSR and the LightStream 1010 switch in
Cisco IOS Release 12.1(5)EY1.
•
Power-on-diagnostics
Caveats
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
29
Restriction
Caveats describe unexpected behavior or defects in Cisco IOS software releases. Caveats use a tracking
number (DDTS No.) and the release number to maintain the database information. For a list of the
caveats and their status for the Cisco IOS Release for the Catalyst 8510 and the LightStream 1010 switch
see the document, Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS
Release 12.1(26)E8, Part 2: Caveats.
Restriction
This section describes the following Catalyst 8510 MSR and the LightStream 1010 switch restriction:
Unicast Reverse Path Forwarding Not Supported
The Catalyst 8510 MSR and the LightStream 1010 switches do not support Unicast Reverse Path
Forwarding (uRPF).
Interoperability
Starting with Cisco IOS Release 12.0(10)W5(18b) software release, hardware and software functionality
interoperability exists between CSR interface modules and MSR interface modules by way of the ATM
router module on the MSR chassis running an MSR image.
Y2K Compliance
Catalyst 8510 and LightStream 1010 systems running Cisco IOS Release 12.0(0.6)W5(1) or later have
been certified as Y2K Compliant. For more information, see the following URL:
http://www.cisco.com/warp/public/752/2000/.
Related Documentation
30
•
Site Preparation and Safety Guide
•
Quick Reference Catalyst 8510 and LightStream 1010 Hardware Information
•
ATM and Layer 3 Module Installation Guide
•
Guide to ATM Technology
•
ATM and Layer 3 Quick Software Configuration Guide
•
ATM and Layer 3 Switch Router Command Reference
•
ATM Switch Router Software Configuration Guide
•
Layer 3 Software Feature and Configuration Guide
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
Obtaining Documentation
Obtaining Documentation
Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several
ways to obtain technical assistance and other technical resources. These sections explain how to obtain
technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco documentation on the World Wide Web at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
http://www.cisco.com
International Cisco websites can be accessed from this URL:
http://www.cisco.com/public/countries_languages.shtml
Ordering Documentation
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
•
Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from
the Ordering tool:
http://www.cisco.com/en/US/partner/ordering/index.shtml
•
Nonregistered Cisco.com users can order documentation through a local account representative by
calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in
North America, by calling 800 553-NETS (6387).
Documentation Feedback
You can submit e-mail comments about technical documentation to [email protected].
You can submit comments by using the response card (if present) behind the front cover of your
document or by writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
31
Obtaining Technical Assistance
Obtaining Technical Assistance
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, the Cisco
Technical Assistance Center (TAC) provides 24-hour-a-day, award-winning technical support services,
online and over the phone. Cisco.com features the Cisco TAC website as an online starting point for
technical assistance. If you do not hold a valid Cisco service contract, please contact your reseller.
Cisco TAC Website
The Cisco TAC website provides online documents and tools for troubleshooting and resolving technical
issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365
days a year. The Cisco TAC website is located at this URL:
http://www.cisco.com/tac
Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password. If you
have a valid service contract but do not have a login ID or password, register at this URL:
http://tools.cisco.com/RPF/register/register.do
Opening a TAC Case
Using the online TAC Case Open Tool is the fastest way to open P3 and P4 cases. (P3 and P4 cases are
those in which your network is minimally impaired or for which you require product information.) After
you describe your situation, the TAC Case Open Tool automatically recommends resources for an
immediate solution. If your issue is not resolved using the recommended resources, your case will be
assigned to a Cisco TAC engineer. The online TAC Case Open Tool is located at this URL:
http://www.cisco.com/tac/caseopen
For P1 or P2 cases (P1 and P2 cases are those in which your production network is down or severely
degraded) or if you do not have Internet access, contact Cisco TAC by telephone. Cisco TAC engineers
are assigned immediately to P1 and P2 cases to help keep your business operations running smoothly.
To open a case by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a complete listing of Cisco TAC contacts, go to this URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
TAC Case Priority Definitions
To ensure that all cases are reported in a standard format, Cisco has established case priority definitions.
Priority 1 (P1)—Your network is “down” or there is a critical impact to your business operations. You
and Cisco will commit all necessary resources around the clock to resolve the situation.
Priority 2 (P2)—Operation of an existing network is severely degraded, or significant aspects of your
business operation are negatively affected by inadequate performance of Cisco products. You and Cisco
will commit full-time resources during normal business hours to resolve the situation.
32
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
Obtaining Additional Publications and Information
Priority 3 (P3)—Operational performance of your network is impaired, but most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Priority 4 (P4)—You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
•
Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Go
to this URL to visit the company store:
http://www.cisco.com/go/marketplace/
•
The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as
ordering and customer support services. Access the Cisco Product Catalog at this URL:
http://cisco.com/univercd/cc/td/doc/pcat/
•
Cisco Press publishes a wide range of general networking, training and certification titles. Both new
and experienced users will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press online at this URL:
http://www.ciscopress.com
•
Packet magazine is the Cisco quarterly publication that provides the latest networking trends,
technology breakthroughs, and Cisco products and solutions to help industry professionals get the
most from their networking investment. Included are networking deployment and troubleshooting
tips, configuration examples, customer case studies, tutorials and training, certification information,
and links to numerous in-depth online resources. You can access Packet magazine at this URL:
http://www.cisco.com/packet
•
iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet
business strategies for executives. You can access iQ Magazine at this URL:
http://www.cisco.com/go/iqmagazine
•
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and private internets and
intranets. You can access the Internet Protocol Journal at this URL:
http://www.cisco.com/ipj
•
Training—Cisco offers world-class networking training. Current offerings in network training are
listed at this URL:
http://www.cisco.com/en/US/learning/index.html
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We
Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst,
CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco
Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast,
EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
33
Obtaining Additional Publications and Information
Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing,
Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, TeleRouter, The Fastest Way to Increase Your Internet
Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0502R)
Copyright © 2006 Cisco Systems, Inc. All rights reserved.
34
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
Obtaining Additional Publications and Information
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
35
Obtaining Additional Publications and Information
36
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
Obtaining Additional Publications and Information
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
37
Obtaining Additional Publications and Information
38
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
Obtaining Additional Publications and Information
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01
39
Obtaining Additional Publications and Information
40
Release Notes for the Catalyst 8510 and the LightStream 1010 Switch for Cisco IOS Release 12.1(26)E8, Part 1: System Requirements
OL-14457-01