Gigabit Interface Converter Installation Note
Product Numbers: WS-G5482, WS-G5483, WS-G5484, WS-G5486, WS-G5487, CWDM-GBIC-xxxx=,
DWDM-GBIC-xx.xx=, WDM-GBIC-REC=
The GBIC is a hot-swappable input/output device that plugs into a Gigabit Ethernet port, linking the
module port with the fiber-optic or copper network.
Contents
This installation note contains the following sections:
•
Contents, page 1
•
Overview, page 2
•
Specifications, page 4
•
Safety Overview, page 6
•
Required Tools, page 12
•
Installing the GBIC, page 13
•
Connecting to the CWDM Passive Optical System, page 15
•
Removing a GBIC, page 15
•
Translated Safety Warnings, page 16
•
Standards Compliance Specifications, page 20
•
Related Documentation, page 21
•
Obtaining Documentation and Submitting a Service Request, page 22
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Overview
Overview
The GBIC transceiver modules are hot-pluggable I/O devices that plug into module sockets. The
transceiver connects the electrical circuitry of the module with the optical or copper network.
You can use any combination of GBIC modules that your Cisco device supports. The only restrictions
are that each port must match the wavelength specifications on the other end of the cable and that the
cable must not exceed the stipulated cable length for reliable communications. Use only Cisco GBIC
transceiver modules with your Cisco device. This installation note provides the installation instructions
for the Gigabit Interface Converters (GBICs) listed in Table 1.
Table 1
GBIC Product Numbers and Descriptions
Product Number
Description
1-Gigabit Ethernet
WS-G5482
1000BASE-T GBIC transceiver module for copper networks
WS-G5483
1000BASE-T GBIC transceiver module for copper networks, extended temp
WS-G5484
1000BASE-SX GBIC transceiver module for MMF, 850-nm wavelength
WS-G5486
1000BASE-LX/LH GBIC transceiver module for SMF, 1300-nm wavelength
WS-G5487
1000BASE-ZX GBIC transceiver module for SMF, 1550-nm wavelength
CWDM
CWDM-GBIC-1470=
Longwave 1470 nm laser, single mode
CWDM-GBIC-1490=
Longwave 1490 nm laser, single mode
CWDM-GBIC-1510=
Longwave 1510 nm laser, single mode
CWDM-GBIC-1530=
Longwave 1530 nm laser, single mode
CWDM-GBIC-1550=
Longwave 1550 nm laser, single mode
CWDM-GBIC-1570=
Longwave 1570 nm laser, single mode
CWDM-GBIC-1590=
Longwave 1590 nm laser, single mode
CWDM-GBIC-1610=
Longwave 1610 nm laser, single mode
DWDM
DWDM-GBIC-60.6=
Longwave 1560.61 nm laser (100-GHz ITU channel 21), single mode
DWDM-GBIC-59.7=
Longwave 1559.79 nm laser (100-GHz ITU channel 22), single mode
DWDM-GBIC-58.98=
Longwave 1558.98 nm laser (100-GHz ITU channel 23), single mode
DWDM-GBIC-58.17=
Longwave 1558.17 nm laser (100-GHz ITU channel 24), single mode
DWDM-GBIC-56.55=
Longwave 1556.55 nm laser (100-GHz ITU channel 26), single mode
DWDM-GBIC-55.75=
Longwave 1555.75 nm laser (100-GHz ITU channel 27), single mode
DWDM-GBIC-54.94=
Longwave 1554.94 nm laser (100-GHz ITU channel 28), single mode
DWDM-GBIC-54.13=
Longwave 1554.13 nm laser (100-GHz ITU channel 29), single mode
DWDM-GBIC-52.52=
Longwave 1552.52 nm laser (100-GHz ITU channel 31), single mode
DWDM-GBIC-51.72=
Longwave 1551.72 nm laser (100-GHz ITU channel 32), single mode
DWDM-GBIC-50.92=
Longwave 1550.92 nm laser (100-GHz ITU channel 33), single mode
DWDM-GBIC-50.12=
Longwave 1550.12 nm laser (100-GHz ITU channel 34), single mode
Gigabit Interface Converter Installation Note
2
78-15299-03
Overview
Table 1
GBIC Product Numbers and Descriptions (continued)
Product Number
Description
DWDM-GBIC-48.51=
Longwave 1548.51 nm laser (100-GHz ITU channel 36), single mode
DWDM-GBIC-47.72=
Longwave 1547.72 nm laser (100-GHz ITU channel 37), single mode
DWDM-GBIC-46.92=
Longwave 1546.92 nm laser (100-GHz ITU channel 38), single mode
DWDM-GBIC-46.12=
Longwave 1546.12 nm laser (100-GHz ITU channel 39), single mode
DWDM-GBIC-44.53=
Longwave 1544.53 nm laser (100-GHz ITU channel 41), single mode
DWDM-GBIC-43.73=
Longwave 1543.73 nm laser (100-GHz ITU channel 42), single mode
DWDM-GBIC-42.94=
Longwave 1542.94 nm laser (100-GHz ITU channel 43), single mode
DWDM-GBIC-42.14=
Longwave 1542.14 nm laser (100-GHz ITU channel 44), single mode
DWDM-GBIC-40.56=
Longwave 1540.56 nm laser (100-GHz ITU channel 46), single mode
DWDM-GBIC-39.77=
Longwave 1539.77 nm laser (100-GHz ITU channel 47), single mode
DWDM-GBIC-38.98=
Longwave 1538.98 nm laser (100-GHz ITU channel 48), single mode
DWDM-GBIC-38.19=
Longwave 1538.19 nm laser (100-GHz ITU channel 49), single mode
DWDM-GBIC-36.61=
Longwave 1536.61 nm laser (100-GHz ITU channel 51), single mode
DWDM-GBIC-35.82=
Longwave 1535.82 nm laser (100-GHz ITU channel 52), single mode
DWDM-GBIC-35.04=
Longwave 1535.04 nm laser (100-GHz ITU channel 53), single mode
DWDM-GBIC-34.25=
Longwave 1534.25 nm laser (100-GHz ITU channel 54), single mode
DWDM-GBIC-32.68=
Longwave 1532.68 nm laser (100-GHz ITU channel 56), single mode
DWDM-GBIC-31.90=
Longwave 1531.90 nm laser (100-GHz ITU channel 57), single mode
DWDM-GBIC-31.12=
Longwave 1531.12 nm laser (100-GHz ITU channel 58), single mode
DWDM-GBIC-30.33=
Longwave 1530.33 nm laser (100-GHz ITU channel 59), single mode
WDM-GBIC-REC=
The R/O WDM GBIC receiver operates as a pluggable receiver on any
unidirectional link in a CWDM or DWDM transport network; there is no
transmitter in the GBIC. The receiver can be used for all wavelengths
supported by Cisco CWDM and DWDM transceivers and can be used
interchangeably with 1000BASE-SX, 1000BASE-LX/LH, and
1000BASE-ZX transceivers on a port-by-port basis. Single SC connector.
A copper GBIC transceiver is shown in Figure 1.
Gigabit Interface Converter Installation Note
78-15299-03
3
Specifications
Copper GBIC
49959
Figure 1
RJ-45
connector
Plastic tab
CWDM and DWDM GBICs are very similar to non-WDM GBICs in appearance. Figure 2 shows a
CWDM GBIC with one optical port dust plug removed.
CWDM GBIC (Yellow-Coded CWDM-GBIC-1550= Shown)
7
1
100 SING
CWD 0BASE LE-M
M-G -CW OD
B
I
C-15 DM GB E
50= IC
Figure 2
2
5
4
3
1
Color band on label
5
Optical bore dust plug
2
Alignment groove
6
Receive optical bore
3
Spring clip
7
Color dot
4
Transmit optical bore
— —
84472
6
Specifications
The 1000BASE-T GBIC devices support 100-meter links of CAT5E cables. Specifications for the other
GBICs listed in Table 1 are provided in Table 2 to Table 5.
Gigabit Interface Converter Installation Note
4
78-15299-03
Specifications
Table 2
1-Gigabit Optical GBIC Transceiver Module Cabling Specifications
Core Size
(micron)
Modal
Bandwidth
(MHz/km) Cable Distance
MMF
62.5
62.5
50.0
50.0
160
200
400
500
722 feet (220 m)
902 feet (275 m)
1640 feet (500 m)
1804 feet (550 m)
MMF1
62.5
50.0
50.0
500
400
500
1804 feet (550 m)
1804 feet (550 m)
1804 feet (550 m)
SMF
G.652
—
6.2 miles (10 km)
SMF
G.652
—
43.4 to 62 miles
(70 to 100 km)
SFP Module Model
Wavelength
(nanometers)
Fiber Type
WS-G5484
850
WS-G5486
1310
WS-G5487
1550
1. A mode-conditioning patch cord is required at all times per IEEE specifications.
Table 3
1-Gigabit GBIC Transceiver Module Optical Transmit and Receive Specifications
Transceiver Type
Transmit
Power
(dBm)
Receive
Power
(dBm)
WS-G5484
1000BASE-SX,
850-nm MMF
–3 (Max)
–9.5 (Min)
0 (Max)
–17 (Min)
770 to 860
WS-G5486
1000BASE-LX/LH, –3 (Max)
1310-nm SMF
–9.5 (Min)
–3 (Max)
–19 (Min)
1260 to 1355
WS-G5487
1000BASE-ZX,
1550-nm SMF
–3 (Max)
–23 (Min)
1500 to 1580
SFP Transceiver
Module Model
+5 (Max)
0 (Min)
Transmit and Receive
Wavelength (nm)
The 1000BASE-T GBIC devices support 100-meter links of CAT5E cables.
Table 4
CWDM GBIC Transceiver Module Optical Parameters
Parameter
Minimum
Typical
Maximum
Units
Notes and Conditions
Transmitter Center
Wavelength
(x–4)
—
(x + 7)
nm
Available center wavelengths are
1470, 1490, 1510, 1530, 1550, 1570,
1590, and 1610 nm
Side-Mode Suppression Ratio 30
—
—
dB
—
Transmitter Optical Output
Power
+1.0
+3.0
+5.0
dBm
Average power coupled into
single-mode fiber
Receiver Optical Input Power
(Bit error rate [BER] <10-12
with pseudo-random bit
sequence [PRBS] 2-7-1)
–29.0
–33.0
–7.0
dBm
@ 1.25 Gbps, 140°F (60°C) case
temperature
Optical Input Wavelength
1450
—
1620
nm
—
Gigabit Interface Converter Installation Note
78-15299-03
5
Safety Overview
Table 4
CWDM GBIC Transceiver Module Optical Parameters
Parameter
Minimum
Typical
Maximum
Units
Notes and Conditions
Transmitter Extinction Ratio
9
—
—
dB
—
Dispersion Penalty at 100 km
—
—
3
dB
@ 1.25 Gbps
Table 5
DWDM GBIC Transceiver Module Optical Parameters
Parameter
Minimum
Typical
Maximum
Units
Notes/ Conditions
Spectral Width
—
—
0.3
nm
Full width, –20 dB from maximum
Transmitter Center Wavelength
x–100
X
X+100
pm
See Table 1 for center wavelengths
Side-Mode Suppression Ratio
30
—
—
dB
—
Transmitter Extinction Ratio
9
—
—
dB
—
Transmitter Optical Output Power
0.0
—
3.0
dBm
Average power coupled into
single-mode fiber
Receiver Optical Input Power (BER
<10-12 with PRBS 2-7-1)
–28.0
—
–7.0
dBm
1.25 Gbps
Receiver Optical Input Wavelength
1450
—
1620
nm
—
Power Penalty
—
—
3
dB
Measured at 3600 ps/nm chromatic
dispersion
OSNR Penalty
—
—
3
dB
Measured at 20 dB OSNR,
0.1 nm RBW
Safety Overview
Safety warnings appear throughout this publication in procedures that, if performed incorrectly or are
ignored, may harm you. A warning symbol precedes each warning statement.
Gigabit Interface Converter Installation Note
6
78-15299-03
Safety Overview
Statement 1071—Warning Definition
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Gigabit Interface Converter Installation Note
78-15299-03
7
Safety Overview
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Gigabit Interface Converter Installation Note
8
78-15299-03
Safety Overview
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Gigabit Interface Converter Installation Note
78-15299-03
9
Safety Overview
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
Gigabit Interface Converter Installation Note
10
78-15299-03
Safety Overview
Gigabit Interface Converter Installation Note
78-15299-03
11
Required Tools
Warning
Class 1 laser product. Statement 1008
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments. Statement 1051
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Required Tools
You will need these tools to install the GBIC transceiver module:
•
Wrist strap or other personal grounding device to prevent ESD occurrences.
•
Antistatic mat or antistatic foam to set the transceiver on.
•
Fiber-optic end-face cleaning tools and inspection equipment. For complete information on
inspecting and cleaning fiber-optic connections, refer to the white-paper document at this URL:
http://www.cisco.com/en/US/tech/tk482/tk876/technologies_white_paper09186a0080254eba.shtml
Gigabit Interface Converter Installation Note
12
78-15299-03
Installing the GBIC
Installing the GBIC
To install a GBIC transceiver module, follow these steps:
Step 1
Remove the GBIC transceiver from its protective packaging.
Step 2
Check the label on the GBIC transceiver to verify that the GBIC transceiver is the correct model for your
network.
Step 3
Grip the sides of the GBIC transceiver with your thumb and forefinger, and carefully align the GBIC
transceiver with the module GBIC socket opening.
Step 4
Carefully insert the GBIC through the socket flap and slide it into the module GBIC socket. (See
Figure 3 for optical GBICs or Figure 4 for copper GBICs.) Continue sliding the GBIC transceiver into
the socket until you hear a click which indicates that the GBIC is locked into the socket.
Caution
Note
You must insert the GBIC straight into the socket (either horizontally or vertically, depending
on the orientation of the socket). If you do not install the GBIC correctly or you use excessive
force, you will damage the GBIC or the socket.
GBICs are keyed to prevent incorrect insertion.
For optical GBIC transceivers, before removing the dust plugs and making any optical connections,
observe the following guidelines:
– Always keep the protective dust plugs on the unplugged fiber-optic cable connectors and the
transceiver optical bores until you are ready to make a connection.
– Always inspect and clean the SC connector end-faces just before making any connections. Refer
to the Tip on this page for a pointer to a fiber-optic inspection and cleaning white paper.
– Always grasp the SC connector housing to plug or unplug a fiber-optic cable.
Step 5
Remove the dust plugs from the network interface cable SC connectors. Save the dust plugs for future
use.
Step 6
Inspect and clean the SC connector’s fiber-optic end-faces. Refer to the Tip below for a pointer to a
fiber-optic inspection and cleaning white paper.
Tip
Step 7
For complete information on inspecting and cleaning fiber-optic connections, refer to the white-paper
document at this URL:
http://www.cisco.com/en/US/tech/tk482/tk876/technologies_white_paper09186a0080254eba.shtml
Remove the dust plugs from the GBIC transceiver optical bores.
Note
The Read-Only WDM GBIC (WDM-GBIC-REC=) has only one optical bore (receive).
Step 8
Immediately attach the network interface cable SC connector to the GBIC transceiver.
Step 9
To connect 1000BASE-T GBIC transceivers to a copper network, follow these substeps:
Gigabit Interface Converter Installation Note
78-15299-03
13
Installing the GBIC
Caution
a.
Insert the Category 5 network cable RJ-45 connector into the GBIC transceiver RJ-45 connector.
Note
b.
To comply with GR-1089 intra-building lightning immunity requirements, you must use
grounded, shielded, twisted-pair Category 5 cabling.
When connecting to a 1000BASE-T-compatible server, workstation, or router, use
four-twisted-pair, straight-through Category 5 cabling for the GBIC transceiver port. When
connecting to a 1000BASE-T-compatible switch or repeater, use four-twisted-pair, crossover
Category 5 cabling.
Insert the other end of the network cable into an RJ-45 connector on a 1000BASE-T-compatible
target device.
Figure 3
Installing an Optical GBIC (WS-G5484, WS-G5486, WS-G5487, and WDM-REC-GBIC=)
GBIC
Squeeze in clips
and slide GBIC
into slot
NK
LI
51180
Plug
Gigabit Interface Converter Installation Note
14
78-15299-03
Connecting to the CWDM Passive Optical System
Figure 4
Installing a Copper GBIC (WS-G5483)
Squeeze in clips
and slide GBIC
into slot
GBIC
K
85745
LIN
Connecting to the CWDM Passive Optical System
For information on connecting CWDM GBIC modules to a CWDM network, refer to the Installation
Note for the Cisco CWDM Passive Optical System at:
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/installation/note/78_16565
.html#wp56420
Removing a GBIC
If you are removing a GBIC, follow these steps:
Step 1
Disconnect the network fiber-optic cable or copper cable from the GBIC connector.
Step 2
Release the GBIC from the slot by simultaneously squeezing the two plastic tabs (one on each side of
the GBIC).
Step 3
Slide the GBIC out of the module slot.
Caution
Note
Step 4
You must remove the GBIC straight out of the socket (either horizontally or vertically,
depending on the orientation of the socket). If you do not remove the GBIC correctly or you
use excessive force, you will damage the GBIC or the socket.
A flap drops down to protect the module socket.
Place the GBIC transceiver in an antistatic bag.
Gigabit Interface Converter Installation Note
78-15299-03
15
Translated Safety Warnings
Translated Safety Warnings
This section repeats in multiple languages the basic warnings that appear in this document.
Statement 1008—Class 1 Laser Product
Warning
Waarschuwing
Varoitus
Class 1 laser product.
Klasse-1 laser produkt.
Luokan 1 lasertuote.
Attention
Produit laser de classe 1.
Warnung
Laserprodukt der Klasse 1.
Avvertenza
Prodotto laser di Classe 1.
Advarsel
Laserprodukt av klasse 1.
Aviso
Produto laser de classe 1.
¡Advertencia!
Varning!
Aviso
Advarsel
Producto láser Clase I.
Laserprodukt av klass 1.
Produto a laser de classe 1.
Klasse 1 laserprodukt.
Gigabit Interface Converter Installation Note
16
78-15299-03
Translated Safety Warnings
Statement 1040—Product Disposal
Warning
Waarschuwing
Varoitus
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle
nationale wetten en reglementen.
Tämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives
de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes
erfolgen.
Avvertenza
Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.
Advarsel
Endelig kassering av dette produktet skal være i henhold til alle relevante nasjonale lover og
bestemmelser.
Aviso
¡Advertencia!
Varning!
Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.
Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Vid deponering hanteras produkten enligt gällande lagar och bestämmelser.
Gigabit Interface Converter Installation Note
78-15299-03
17
Translated Safety Warnings
Aviso
Advarsel
O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações
nacionais.
Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.
Gigabit Interface Converter Installation Note
18
78-15299-03
Translated Safety Warnings
Statement 1051—Laser Radiation
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments. Statement 1051
Waarschuwing
Losgekoppelde of losgeraakte glasvezels of aansluitingen kunnen onzichtbare laserstraling
produceren. Kijk niet rechtstreeks in de straling en gebruik geen optische instrumenten rond deze
glasvezels of aansluitingen.
Varoitus
Irrotetuista kuiduista tai liittimistä voi tulla näkymätöntä lasersäteilyä. Älä tuijota säteitä tai katso
niitä suoraan optisilla välineillä.
Attention
Les fibres ou connecteurs débranchés risquent d'émettre des rayonnements laser invisibles à l'œil.
Ne regardez jamais directement les faisceaux laser à l'œil nu, ni d'ailleurs avec des instruments
optiques.
Warnung
Unterbrochene Fasern oder Steckerverbindungenkönnen unsichtbare Laserstrahlung abgeben.
Blicken Sie weder mit bloßem Auge noch mit optischen Instrumenten direkt in Laserstrahlen.
Avvertenza
Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono
mai essere osservati direttamente o attraverso strumenti ottici.
Advarsel
Det kan forekomme usynlig laserstråling fra fiber eller kontakter som er frakoblet. Stirr ikke direkte
inn i strålene eller se på dem direkte gjennom et optisk instrument.
Aviso
¡Advertencia!
Varning!
Radiação laser invisível pode ser emitida de conectores ou fibras desconectadas. Não olhe
diretamente para os feixes ou com instrumentos ópticos.
Es posible que las fibras desconectadas emitan radiación láser invisible. No fije la vista en los
rayos ni examine éstos con instrumentos ópticos.
Osynlig laserstrålning kan avges från frånkopplade fibrer eller kontaktdon. Rikta inte blicken in i
strålar och titta aldrig direkt på dem med hjälp av optiska instrument.
Gigabit Interface Converter Installation Note
78-15299-03
19
Standards Compliance Specifications
Aviso
Advarsel
Radiação laser invisível pode ser emitida a partir de fibras ou conectores desconectados. Não fixe
o olhar nos feixes e nem olhe diretamente com instrumentos ópticos.
Usynlig laserstråling kan forekomme fra brugte fibre eller stik. Stir ikke ind i stråler eller direkte
med optiske instrumenter.
Standards Compliance Specifications
This section provides compliance information for the GBIC.
Gigabit Interface Converter Installation Note
20
78-15299-03
Related Documentation
FCC Class A Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case users will be
required to correct the interference at their own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference
stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment
causes interference to radio or television reception, try to correct the interference by using one or more
of the following measures:
•
Turn the television or radio antenna until the interference stops.
•
Move the equipment to one side or the other of the television or radio.
•
Move the equipment farther away from the television or radio.
•
Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is,
make certain the equipment and the television or radio are on circuits controlled by different circuit
breakers or fuses.)
Modifications to this product not authorized by Cisco Systems could void the FCC approval and negate
your authority to operate the product.
Class 1 Laser Compliance
This product has been tested and found to comply with the limits for Class 1 laser for IEC825, EN60825,
and 21CFR1040 specifications.
Related Documentation
For hardware installation and maintenance information on specific Cisco routers and switches, see the
installation and configuration guide for your router or switch.
For software configuration information and support, see the Cisco IOS software configuration and
command reference publications for the installed Cisco IOS software release or the Catalyst operating
system software configuration and command reference publications for the installed Catalyst operating
system software release.
Support summaries for all GBICs are at:
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_
6981.html
Gigabit Interface Converter Installation Note
78-15299-03
21
Obtaining Documentation and Submitting a Service Request
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS version 2.0.
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence,
Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are
service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP,
CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo,
Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive,
HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace,
MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare,
SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo
are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. (0812R)
© 2003–2009 Cisco Systems, Inc. All rights reserved.
Gigabit Interface Converter Installation Note
22
78-15299-03