EON‐AD1‐ADP‐12
AC24V/DC12V Dual Power Module for CCTV „
z
z
z
z
z
z
z
z
z
V 1.0 May 2013
Data sheet
Features Input Non‐Polarity ,Dual mode wide input voltage range.(12~36Vdc/20~28Vac). Input and output isolation. Compact size(73mm×19.5mm×17mm,L×W×H),convenient insert in 1” inch tube. Meets RoHs , FCC & CE Class B Certification. Power input built‐in Surge protector meets IEC61000‐4‐5 demand. Short‐circuit protection. For indoor use only. Extra‐low ripple and noise. 1 years limited warranty.(”The damages caused by the incorrect or improper man‐made assembly ,over working voltage ,flooded ,lighting…etc. are out‐of warranty”).
Specifications Ta=25℃, Unless Otherwise noted PARAMETER SYMBOL MIN
TYP
Input
24
24
0.95
8
26.6
Output
12
0.5
74
5
MAX
UNIT
TEST CONDITIONS
28
36
Vac
Vdc
Amp
Amp
Amp
47~63Hz, Iload=0.5A
Iload=0.5A
Vin=12Vdc, Iload=0.5A
Vin=12Vdc, Iload=0.5A
Vin=24Vac / 60Hz, Iload=0.5A
12.6
Vin=24Vac / 60Hz Iload=0.5A 15
Vdc
A
%
mV
AC Voltage DC Voltage Start‐Up Current DC Inrush Current AC Inrush Current Vin Vin Iin 20
12
DC Voltage Maximum Current Efficiency Ripple & Noise( Note1) Vout Iout η Vp‐p 11.4
Line Regulation 0.1 0.5 % Load Regulation 0.5 1.2 % Minimum Load Temp Coefficient Setup Time Hold‐up time Short Circuit Working Temp Working Humidity Storage Temp Safety Standards EMI Conduction & Radiation MTBF Dimension Standard Package Weight 0
+/‐ 0.08 (Typ) mA
%/℃ 363 ms (Typ)
10.7 ms (Typ)
Protection
YES (No smoke or flame duration of 10 minutes)
Environment
‐20 ℃ ~ 50 ℃ / ‐4℉ ~ 122℉
20 ~ 90 % RH
‐25 ℃ ~ 75 ℃ / ‐13℉ ~ 167℉
Safety & EMC (Note2)
Design refer LVD
Compliance to EN55022(CISPR22)Class B
Others
>100 K Hours (25℃)
73 x 19.5 × 17 mm (L×W×H) , tolerance: + / ‐0.5mm
500 pcs / Carton
18.5 g±3% / PCS
Note
Vin=20~28Vac / 60Hz, Iload=0.5A
Vin=24Vac / 60Hz Iload =0.1~0.5A
Vin=24Vac or Vin=12Vdc
Vin=12Vdc,Iload=0.5A Ta:‐20℃~50℃
Vin=24Vac / 60Hz Iload=0.5A 1. Ripple & Noise are measured at 20Mhz of bandwidth by using a 12” twisted pair‐wire terminated with a 0.1uF MLCC & 1uF parallel electrolytic capacitor. 2. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re­conformed that it still meets EMC directives. EON‐AD1‐ADP‐12
AC24V/DC12V Dual Power Module for CCTV V 1.0 MAY 2013 Data sheet
17 mm
„
Mechanical Specification Unit: mm „
Input & Output Terminal Assignment INPUT:
Please use Stranded wire or Solid wire
AWG 14~18
(Advise stripping length : 6mm)
OUTPUT:
DC PLUG 5.5*2.1
INPUT Pin No Assignment Terminal Pin No PIN1 DC12V or AC24V 5.0mm European P.C.B Type Terminal PIN2 „
DC12V or AC24V Color :Green Inner Pin (ID:2.1mm)
Outer Pin (OD:5.5mm)
OUTPUT Assignment Terminal
+12Vdc GND Derating Curve DC PLUG 5.5*2.1