National Conference On “Emerging Trends in Mechanical Engineering and Technology” (ETME- 2017)
rd
th
23 and 24 March, 2017
Title (Word Template for Full Length Paper)
1st Author
2nd Author
3rd Author
1st author's affiliation
Telephone number
2nd author's affiliation
Telephone number
3rd author's affiliation
Telephone number
1st author's E-mail
address
2nd E-mail
3rd E-mail
Abstract
The abstract is to be in fully-justified italicized text, at
the top of the left-hand column as it is here, below the
author information. Use the word “Abstract” as the title,
in 12-point Times, boldface type, centered relative to the
column, initially capitalized. The abstract is to be in 10point, single-spaced type, and may be up to 3 in. (7.62
cm) long. Leave two blank lines after the abstract, then
begin the main text. All manuscripts must be in English.
1. Introduction
These guidelines include complete descriptions of the
fonts, spacing, and related information for producing
your proceedings manuscripts. Please follow them and if
you have any questions, direct them to the production
editor in charge of your proceedings at the IEEE
Computer Society Press: Phone (714) 821-8380 or Fax
(714) 761-1784.
2. Formatting Your Paper
All printed material, including text, illustrations, and
charts, must be kept within a print area of 6-7/8 inches
(17.5 cm) wide by 8-7/8 inches (22.54 cm) high. Do not
write or print anything outside the print area. All text
must be in a two-column format. Columns are to be 31/4 inches (8.25 cm) wide, with a 5/16 inch (0.8 cm)
space between them.
Text must be fully justified. A format sheet with the
margins and placement guides is available in both Word
and PDF files as <format.doc> and <format.pdf>. It
contains lines and boxes showing the margins and print
areas. If you hold it and your printed page up to the light,
you can easily check your margins to see if your print
area fits within the space allowed.
3. Main Title
The main title (on the first page) should begin 1-3/8
inches (3.49 cm) from the top edge of the page, centered,
and in Times 14-point, boldface type. Capitalize the first
letter of nouns, pronouns, verbs, adjectives, and adverbs;
do not capitalize articles, coordinate conjunctions, or
prepositions (unless the title begins with such a word).
Leave two blank lines after the title.
4. Author Name(s) and Affiliation(s)
Author names and affiliations are to be centered
beneath the title and printed in Times 12-point, nonboldface type. Multiple authors may be shown in a twoor three-column format, with their affiliations below their
respective names. Affiliations are centered below each
author name, italicized, not bold.
Include e-mail
addresses if possible. Follow the author information by
two blank lines before main text.
5. Second and Following Pages
The second and following pages should begin 1.0 inch
(2.54 cm) from the top edge. On all pages, the bottom
margin should be 1-1/8 inches (2.86 cm) from the bottom
edge of the page for 8.5 x 11-inch paper; for A4 paper,
approximately 1-5/8 inches (4.13 cm) from the bottom
edge of the page.
6. Type-style and Fonts
Wherever Times is specified, Times Roman, or New
Times Roman may be used. If neither is available on
your word processor, please use the font closest in
appearance to Times that you have access to. Please
avoid using bitmapped fonts if possible. True-Type 1
fonts are preferred.
Organized by: Department of Mechanical Engineering”, School of Engineering & Technology, Sharda University, Greater Noida
National Conference On “Emerging Trends in Mechanical Engineering and Technology” (ETME- 2017)
rd
th
23 and 24 March, 2017
7. Main Text
Type your main text in 10-point Times, single-spaced.
Do not use double-spacing. All paragraphs should be
indented 1 pica (approximately 1/6- or 0.17-inch or 0.422
cm). Be sure your text is fully justified—that is, flush
left and flush right. Please do not place any additional
blank lines between paragraphs. You can use courier for
source code.
For I = 1 to 10 do
Print “this figure”
End;
9. Acknowledgements
This work was supported in part by a grant from the
National Science Foundation.
10. References
List and number all bibliographical references in 9point Times, single-spaced, at the end of your paper.
When referenced in the text, enclose the citation number
in square brackets, for example [2-4], [2, 5], and [1].
Figure 1. Example figure.
7.1. Figure and Table Captions
Captions should be 10-point Helvetica (or a similar
sans-serif font), boldface. Callouts should be 9-point
Helvetica, non-boldface. Initially capitalize only the first
word of each figure caption and table title. Figures and
tables must be numbered separately. For example:
“Figure 1. Example figure.”, “Table 1. Table example.”.
Figure captions are to be below the figures (see Figure
1). Table titles are to be centered above the tables (see
Table 1.
Table 1. Table example.
One
8.1.1. Third-order Headings. Third-order headings, as
in this paragraph, are discouraged. However, if you must
use them, use 10-point Times, boldface, initially
capitalized, flush left, preceded by one blank line,
followed by a period and your text on the same line.
Two
Three
8. First-order Headings
[1] Briand, L. C., Daly, J., and Wüst, J., "A unified framework
for coupling measurement in objectoriented systems", IEEE
Transactions on Software Engineering, 25, 1, January 1999, pp.
91-121.
[2] Maletic, J. I., Collard, M. L., and Marcus, A., "Source Code
Files as Structured Documents", in Proceedings 10th IEEE
International Workshop on Program Comprehension
(IWPC'02), Paris, France, June 27-29 2002, pp. 289-292.
[3] Marcus, A., Semantic Driven Program Analysis, Kent State
University, Kent, OH, USA, Doctoral Thesis, 2003.
[4] Marcus, A. and Maletic, J. I., "Recovering Documentationto-Source-Code Traceability Links using Latent Semantic
Indexing", in Proceedings 25th IEEE/ACM International
Conference on Software Engineering (ICSE'03), Portland, OR,
May 3-10 2003, pp. 125-137.
[5] Salton, G., Automatic Text Processing: The Transformation,
Analysis and Retrieval of Information by Computer, AddisonWesley, 1989.
For example, “1. Introduction”, should be Times 12point boldface, initially capitalized, flush left, with one
blank line before, and one blank line after. Use a period
(“.”) after the heading number, not a colon.
8.1. Second-order Headings
As in this heading, they should be Times 11-point
boldface, initially capitalized, flush left, with one blank
line before, and one after.
Organized by: Department of Mechanical Engineering”, School of Engineering & Technology, Sharda University, Greater Noida