ODEON
INSTALLATION INSTRUCTIONS
SQUARE SLIDING DOOR
K-17117T
BEFORE YOU BEGIN
·
· Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
· These instructions contain important care, cleaning,
and warranty information-please leave these
instructions for the consumer.
· Instructions, drawings, and diagrams contained in
this manual present information available at the time
of printing. Although every attempt has been made
to keep them up-to-date, Kohler Company reserves
the right to implement product changes without
further notice.
· Make sure that the bath and the finished wall
material are completely installed prior to installing
your ODEON.
· While most illustrations depict ON FLOOR
installation, and where ever possible, illustrations
showing specific requirements for each option are
given. Where not, dimensions relating to each are
included.
·
·
·
ODEON
·
CAUTION: Risk of injury or product damage.
Tempered glass cannot be cut.
CAUTION: Before commencing installation,
KOHLER strongly recommends reading this
manual.
ATTENTION: Please install this door on Kohler
corner.
IMPORTANT: The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 4 mm/m. KOHLER
Company won t take responsibility of the installation
quality.
(
)
4mm/m
13-1
1060543-T01-B
1
528437
ã
C
, 2008
Copyright Kohler China Ltd., 2008
ROUGHING-IN
Colors/Finishes
B
!
!
B
0 White
SH Bright Silver
/
0
SH
Roughing-In Notes
A
B
K-17117T-L-0
1850mm
K-17117T-L-SH
Note: Max. door opening is 460mm
460mm
A
873mm+7.5mm
-
UNIT: mm
51mm
38mm
Elevation
1060543-T01-B
Plan view
2
201
INSTALLATION REQUIREMENTS
Tools Required
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Phillips Screwdriver
Pencil
Caulk Gun
Measuring Tape
Safety Glasses
Center Punch
Hammer
Knife
Drill & 6mm Drilll Bit, 3.6mm Regnlar Bit
Level
Materials Required
·
·
· Drop Cloth
· Silicone Sealant
1060543-T01-B
3
6mm
3.6mm
PARTS IDENTIFICATION
Wall Jamb
Screw ST4.2x35
Wall Jamb
ST4.2x35
Top / Bottom Track
/
Top Corner Bumper Left
Rubber
Bumper
Top Corner
Bumper Screw Roller Screw
ST4.2x28
Screw Head Cover
4.2x28
Washer
Roller Screw
Plastic
Anchor
Track Insert
Roller
Corner Bracket
Screw Cover
Bottom Corner
Bumper Screw
ST4.2x23
Wall Frame
Screw ST4.2x9.5
ST4.2x23
ST4.2x9.5
Bottom Corner
Bumper Left
Plastic
Clip
Corner Bracket
Track Insert
Top / Bottom Track
/
Top Corner
Rubber
Bumper Screw
Bumper
ST4.2x28
Top Corner
Bumper Right
Wall Jamb
Screw ST4.2x35
ST4.2x35
Wall Jamb
4.2x28
Roller Screw
Screw Head
Cover
Washer
Track Insert
Plastic
Anchor
Roller Screw
Roller
Screw Cover
Bottom Corner
Bumper Screw
ST4.2x23
ST4.2x23
Track Insert
4
ST4.2x9.5
Bottom Corner
Bumper Right
Plastic
Clip
1060543-T01-B
Wall Frame
Screw ST4.2x9.5
1. Marking and Drilling Wall
Jamb Mounting Holes
Shower Head Can Be On
Either Side
Measure and mark on the receptor ledge near the wall,
dimension “B” out from the back wall.
Align outside edge of wall jamb with the mark made on
the receptor ledge. Using a level, plumb the wall jamb
and mark the three wall mounting holes with a pencil.
With a center punch, lightly punch the three hole
locations for the wall jamb. (On ceramic tile, use a
center punch to nick the surface glaze.) Tap the punch
lightly with hammer so as not to crack tile. Use a 6mm
drill bit (a masonry bit for ceramic tile).
After drilling, thoroughly clean the receptor edge and
wall. Insert plastic anchors in all three holes.
Repeat procedure for the other wall jamb.
NOTE: Wear Safety Glasses.
Pencil
Level
Wall Jamb
Inside
Outside
B
Wall Jamb
Shower Receptor
1.
Dimension B for receptor = 871
B=871
10mm
B
(
)
(
)
2. Installing Wall Jambs
Wall Mounting Screw
Install each wall jamb by aligning the holes in the wall
jambs with the holes in the wall. Secure the wall jambs
with 6 ST4.2 x 35 screws provided.
2.
6
ST4.2 x 35
Wall Jamb
ST4.2x35
Shower Receptor
1060543-T01-B
5
3. Installing Panels
3.
Slide the wall frame of fixed panel over the wall jamb.
Rest the fixed panel on the shower ledge.
CAUTION: Place the side with rolling wheels upwards.
Top Track
Wall Frame
Track
Roller Groove
Wall Jamb
Bottom Track
Track
Fixed Panel
Bottom Track Slot
Front Side
4. Installing Bumpers
Remove paper backing from the rubber bumpers and
affix two on each wall frame of fixed panel at top and
bottom as shown.
4.
20
Bumper (Top)
(
)
100
Wall Frame
Wall Frame
Bumper (Bottom)
(
)
20
100
1060543-T01-B
6
5. Installing Corner Brackets and Corner
Bumpers
Corner Bracket
Top Track
NOTE: Corner brackets for top tracks and bottom
tracks are identical.
Slide one corner bracket into the cavities of the top
tracks.
From inside the shower, place the corner bumpers
market “T” into the top tracks as shown and align with
holes in top tracks and attach the corner brackets and
corner bumpers with ST4.2x28 screws.
NOTE: Do not overtighten screws.
Slide one corner bracket into the cavities of the bottom
tracks.
From inside the shower, place the corner bumpers
marked “B” into the bottom tracks as shown and align
with holes in bottom tracks and attach the corner
brackets and corner bumpers with ST4.2x23 screws.
NOTE: Do not overtighten screws.
Top Corner
Bumper
ST4.2x28 Screw
Soft
Soft
ST4.2x28 Screw
ST4.2x23 Screw
Soft
Bottom Track
ST4.2x23
Screw
5.
Corner Bracket
NOTE: Corner bumpers are not identical.
Top corner bumpers are marked “T”.
Bottom corner bumpers are marked “B”.
T
(
ST4.2x28
B
)
(
ST4.2x23
T
B
)
6. Fixing Pannel
USE a 3.6mm drill bit. After drillig, clean the
Secure the wall frame with ST4.2x9.5 Screws provided.
6.
3.6mm
ST4.2x9.5
ST4.2x9.5
Wall Frame
Shower Recepfor
1060543-T01-B
Soft
Bottom
Corner
Bumper
7
7. Testing and Adjustment Of Moving
Panels
Top Track
Screw Cover
Slide one of the moving panels into the closed position.
Slowly slide the other moving panel until the panels
interlock at the corner. If panels do not close together
smoothly, adjust one of the moving panels by loosening
the screw(s) and tilting the panel to get a smooth fit.
Retighten screws.
Should the panel bind or not glide smoothly, loosen
both roller screws and lower the panel an equal amount
on both sides.
After adjust, cover the roller screws and frame screws
with the covers provided.
Moving Panel
Roller Screw
7.
Screw Cover
8. Caulking Door
CAUTION: Apply caulk around the outside of the door
“only.” Caulk applied to the inside of the door will cause
leakage and damage.
Thoroughly clean and dry all dust, dirt, or grease from
bottom track and receptor ledge surfaces to be sealed.
Carefully apply a bead of caulking around the outside
of the door where:
1. Bottom track meets the receptor.
2. Corner brackets meet thereceptor.
3. Wall jamb meets thereceptor.
4. Wall jamb meets wall.
NOTE: Allow caulking to set 24 hours before using
shower.
8.
Caulk Here
Caulk Here
Caulk Here
Caulk Here
1.
2.
3.
4.
24
1060543-T01-B
8
CARE AND CLEANING
Your Kohler Shower Enclosure will remain beautiful if
you take care of it.
Water conditions in various parts of the country will
determine any extra cleaning attention you may have to
give to your new shower enclosure. A simple routine of
daily care will keep your shower enclosure looking like
new.
Kohler does not recommend the use of abrasive
cleaners on any of its products. Harsh cleaners will
damage the metal or glass finish on your shower
enclosre.
An occasional wiping down with a mild detergent
diluted in water is all that needed to keep the panels
and anodized aluminum parts looking new.
Replace seals, when they show signs of wear,
yellowing or are not watertight. Refer to the Kohler
Service Parts page.
1060543-T01-B
9
ODEON
SERVICE PARTS PAGE
SQUARE SLIDING DOOR
K-17117T
1057068
Screw,gb/t 845
ST4.2x35
1057052-*
Wall Jamb
ST4.2x35
1057069
Screw,gb/t 845
ST4.2x75
ST4.2x75
1057045-*
Top/Bottom Track
/
612400
Rubber Bumper
1057066
1057077-*
Screw,gb/t 845
Top Corner
Bumper Assy., Left ST4.2x25
ST4.2x25
1057078-*
Top Corner
Bumper Assy., Right
1057068
Screw,gb/t
845 ST4.2x35
1057044-*
Wall Frame
456404
Screw, #8-32X3/8''
#8-32X3/8''
1031943-*
Cover for screw head
ST4.2x35
1060632
Washer, GB/848-8
1057064
Wall Anchor,
Nylon Hollow
456404
Screw, #8-32X3/8''
#8-32X3/8''
1057047-*
Insert,Top/
Bottom Track
1057060
Glazing Gasket
1057048-*
Top Frame
1031943-*
Cover for screw head
555900
Nylon Roller
Bearing
1057059-*
Friction Space, Right
1057062-*
Corner Bracket Assy
1057050-*
Side Frame Seal
1031943
Cover for
Screw Head
1057072-*
Bottom Corner
Bumper Assy., Left
1057073-*
Bottom Corner
Bumper Assy., Right
1057071
Screw,gb/t
845 ST4.2x9.5
ST4.2x9.5
1057061
Glass Panel
4mm Clear
376x1765x4
1108211
Glass Panel
4mm Clear
With Logo
1057051-*
Corner Interlock
1093571
Glass Panel 4mm Clear
376x1768x4
1057046-*
Side Frame
1057068
Screw,gb/t
845 ST4.2x35
ST4.2x35
604900
Plastic Clip
1057047-*
Insert,Top/
Bottom Track
1057058-*
1057049-*
Bottom Frame Friction Space, Left
Finish/Color Code
-SH=Bright Silver
-0 =White
/
**
** Color code must be specified when ordering.
1060543-T01-B
10
ODEON
SERVICE PARTS PAGE
SQUARE SLIDING DOOR
K-17117T
/
COLOR/FINISH
DESCRIPTION
PART NO.
1057044-*
Wall Frame
1057045-*
Top/Bottom Track
1057046-*
Side Frame
1108211
Glass Panel 4mm Clear with Logo
1093571
Glass Panel 4mm Clear
376X1768X4
1057061
Glass Panel 4mm Clear
376X1765X4
1057060
Glazing Gasket
1057048-*
Top Frame
SH, 0
1057047-*
Insert, Top/Bottom Track
SH, 0
1057049-*
Bottom Frame
SH, 0
1057050-*
Side Frame Seal
SH, 0
1057051-*
Corner Interlock
SH, 0
1057052-*
Wall Jamb
1093570-*
SH, 0
/
SH, 0
SH, 0
SH, 0
1057068
Screw, GB/T 845 ST4.2x35
ST4.2x35
1057069
Screw, GB/T 845 ST4.2x75
ST4.2x75
1057058-*
Friction Space, Left
1057059-*
Odeon Service Part Package
555900
1
Kit1
456404
1060632
1057063-*
Parts Package Kit
Note: Components marked in
1060543-T01-B
Friction Space, Right
SH, 0
Nylon Roller Bearing
Screw, #8-32X3/8''
#8-32X3/8''
Washer, GB/848-8
GB/848-8
604900
Plastic Clip
1057062-*
Corner Bracket Assy.
1057064
Wall Anchor, Nylon Hollow
612400
Rubber Bumper
1057072-*
Bottom Corner Bumper Assy., Left
1057073-*
Bottom Corner Bumper Assy., Right
1057077-*
Top Corner Bumper Assy., Left
1057078-*
Top Corner Bumper Assy., Right
0L, 0
1057071
Screw, GB/T 845 ST4.2x9.5
ST4.2x9.5
1057066
Screw, GB/T 845 ST4.2x28
ST4.2x25
1031943-*
Cover For Screw Head
can only be ordered in whole pack.
11