Door adjustment
Crystal and Keyline Hinge Adjustment
Three-dimensional adjustment
Side adjustment
Height adjustment
Depth adjustment
Rotate the front cam screw to increase or decrease door
overlay (+/- 1/16").
Loosen installation screws to adjust door position
(+/- 1/8"), then retighten.
Rotate the rear cam screw to adjust door gap
(+ 3/32", - 1/32").
Subject to technical modifications without notice. © 2011 Blum, Inc.
Adjust soft close drawers up, down or side to side.
TANDEM plus BLUMOTION 563F
New side adjustment
New rear side adjustment
1. Rotate side adjustment left
or right equally on both locking
devices. Drawer front moves in
the same direction as rotation.
2. After front side adjustment is
made with the locking devices,
rotate the rear side adjustment left
or right to re-align the back of the
drawer box with the front. Drawer
back moves in the same direction
as rotation.
with locking device
R
drawer
front
L
T51.19xx
R
L
Maximum 1.5 (1/16") to left or right (tool-free)
R
L
Maximum 1.5 (1/16") to left or right (tool-free)
NOTE: Side adjustment not available on T51.18xx locking devices
Height adjustment
Tilt adjustment
1.Press up on adjustment tab
Rotate the tilt adjustment lever
on the rear of each runner to
tilt the top of the drawer front
forward.
2.Push towards back of drawer
2
Maximum 3 (1/8") rise of drawer front (tool-free)
1
Maximum 5 (3/16") rise of drawer back (tool-free)
NOTE: Height adjustment available on all TANDEM locking devices
New depth adjustment on runner
New depth adjustable locking device
TANDEM 563 runners feature elongated holes
that allow +/- 4.5 (3/16") depth adjustment.
Locking device
T51.1901.PS
with side, height and
depth adjustment
Turning the adjustment screw allows for up to a + 2.5 (3/32") out adjustment
NOTE: For T51.1901.PS setback in inset applications, see the TANDEM brochure
New bottom mounting
New profile setback
37 (1-15/32")
9 (11/32")
9 (11/32")
22.5 (7/8")
10 (13/32")
37 (1-15/32")
3 (1/8")
setback 3 (1/8")
NOTE: Hole locations to the face of the cabinet stay the same. For inset
applications see the TANDEM brochure
Runner
563F5330B
563F4570B
563F3810B
X
448 (17-5/8")
378 (14-7/8")
319 (12-9/16")
Drawer insertion
Drawer removal
1. Place drawer on runners and
close. Locking devices will
automatically connect to runners.
1. Squeeze orange handles on
locking devices
2. Pull drawer straight out and up
See blum.com for complete technical specifications and installation instructions.
INST-TDM563F.03.12
Subject to technical modifications without notice. © 2012 Blum, Inc.
BAU0026482453 INDR 5633767 MA-580/0EN TAND 563F/A-B
67 (2-5/8")
15.5(5/8")
X
32 (1-1/4")
COMPACT BLUMOTION
Instructions to deactivate your soft close feature on doors.
BLUMOTION deactivation
Switch on the hinge cup
For small or light doors, the BLUMOTION can be deactivated on one of the hinges.
COMPACT BLUMOTION comes in the activated position, marked with a “I”.
The deactivated position is marked with a “0”.
Door must be closed once for the deactivation to be complete.
To reactivate, move switch back to the original position “I”.
1
2
Subject to technical modifications without notice. © 2011 Blum, Inc.
LIT.HNG5501.04.11
Adjusting Your Inset Soft Close Hinge
Adjusting Your Inset Hinge
BLUMOTION
inside
Adjusting Hinges in Quest and Encore (frameless)
Three-dimensional adjustment
Side adjustment
Rotate front screw to increase or decrease
door overlay (±2 mm).
Height adjustment
Depth adjustment
Rotate cam screw on mounting plate to
adjust door position (±2 mm).
Rotate rear spiral tech cam screw to adjust
door gap (+3 mm, -2 mm).
On non-cam mounting plates, loosen
screws, adjust door and retighten screws.
BLUMOTION deactivation
Deactivation switch on hinge cup
For small or light doors, the BLUMOTION can be deactivated on one
of the hinges.
Door must be closed once for the deactivation to be complete.
To reactivate, move switch back to original position.
1
2
Temperature information
CLIP top BLUMOTION is designed to be used at temperatures between 65° and 85° F. Lower or higher temperatures will
not cause damage to the hinge, however they will affect the closing speed. Once the temperature returns to the suggested
range the hinge will return to its optimal closing action.
Dimensions in millimeters (inch equivalents as noted)
© 2012 Blum, Inc.
9