Motion technologies
▶ SERVO-DRIVE for LEGRABOX/TANDEMBOX
▶▶ Applications
Standard cabinet
Planning – horizontal cross member
Cabinet dimensions
KB
LW
LT
Cabinet width
Inner cabinet width
Internal cabinet depth
Motion technologies
Drilling distances – base/cross bar
Cabinet width KB 275–420 mm
LEGRABOX
Chipboard back height N
Cabinet width KB starting at 320 mm
Box systems
LEGRABOX
Z (mm)
184
TANDEMBOX
179
Cabinet width KB starting at 420 mm
N height
Only possible with
chipboard back
Remove lever
extension
Drilling position and space requirement for all applications
Back
Chipboard back
Steel back
NL Nominal length
X
Drilling position
Y
Min. space requirement
Cabinet width KB 320–420 mm
TANDEMBOX
Steel back height N
X (mm)
NL + 19
NL + 2
Y (mm)
NL + 33
NL + 16
Using this assembly position for the bracket profile, both inner pull-out
elements as well as those with overlay fronts can be opened by pushing
and pulling.
Drilling position and min. space requirement – drawer/high fronted pull-out
Back
X (mm)
Y (mm)
SERVO-DRIVE can also be used if there is less space available. At the
Chipboard back
NL + 16
NL + 30
assembly position for the bracket profile, inner pull-out elements can only
Steel back
NL – 1
NL + 13
Note
be opened by pulling (not by pushing).
SERVO-DRIVE with LEGRABOX inner drawer with steel back not possible
NL Nominal length
X
Drilling position
Y
Min. space requirement
558
Catalogue 2016/2017 • KA-120
SERVO-DRIVE for LEGRABOX/TANDEMBOX ◀
Applications ◀◀
Motion technologies
Standard cabinet
Front assembly – position of Blum distance
bumper
Back cabling
BT
Drilling depth
The Blum distance bumper creates and
maintains the required trigger path of 2 mm.
When using a 70 kg LEGRABOX or 65 kg
TANDEMBOX runner, attach four Blum distance
bumpers. For optimal trigger function for front
height FH > 300 mm, use front stabilisation
FA Front overlay
FH Front height
Alternative drilling pattern for PRO-CENTER
and MINIPRESS
BT Drilling depth
Position – drive unit
All back heights except height N
Box systems
X min. (mm)
LEGRABOX
45.0
TANDEMBOX
35.0
Y min. (mm)
68.5
63.5
Motion technologies
Planning – horizontal cross member
Drilling pattern base
Lower cabling
LEGRABOX – back height N
Cabinet width KB (mm)
275–320
> 320
Back
X
Y
X
Y
(mm) (mm) (mm) (mm)
Chipboard back
–
–
45.0
42.0
SERVO-DRIVE with LEGRABOX with steel back height N not
possible
–
Not possible
TANDEMBOX – back height N
Cabinet width KB (mm)
275–320
Back
X
Y
(mm) (mm)
Chipboard back
35.0
55.5
Steel back
–
–
–
Not possible
LH
PL
> 320
X
(mm)
27.5
27.5
Y
(mm)
48.5
48.5
Internal cabinet height
Bracket profile length
Page instructions
Assembly
Assembly – Blum distance bumper
Assembly – Blum transformer 72 W
Cabling
Catalogue 2016/2017 • KA-120
582
582
584
585
559
Motion technologies
▶ SERVO-DRIVE for LEGRABOX/TANDEMBOX
▶▶ Applications
Standard cabinet
Planning – vertical cross member
Cabinet dimensions
KB
LW
LT
Cabinet width
Inner cabinet width
Internal cabinet depth
Drilling distances – base/cross bar
Motion technologies
T
Cabinet width KB 275–420 mm
LEGRABOX
Chipboard back height N
Cabinet width KB starting at 320 mm
Box systems
LEGRABOX
Z (mm)
184
TANDEMBOX
179
Cabinet width KB starting at 420 mm
N height
Only possible with
chipboard back
Remove lever
extension
Drilling position and space requirement for all applications
Back
X (mm)
Chipboard back
NL + 19
Steel back
NL + 2
NL Nominal length
X
Drilling position
T
Position front edge/cross member
Cabinet width KB 320–420 mm
TANDEMBOX
Steel back height N
T (mm)
NL + 34
NL + 17
Using this assembly position for the bracket profile, both inner pull-out
elements as well as those with overlay fronts can be opened by pushing
and pulling.
Drilling position and min. space requirement – drawer/high fronted pull-out
Back
X (mm)
T (mm)
SERVO-DRIVE can also be used if there is less space available. At the
Chipboard back
NL + 16
NL + 31
assembly position for the bracket profile, inner pull-out elements can only
Steel back
NL – 1
NL + 14
Note
be opened by pulling (not by pushing).
SERVO-DRIVE with LEGRABOX inner drawer with steel back not possible
NL Nominal length
X
Drilling position
T
Position front edge/cross member
560
Catalogue 2016/2017 • KA-120
SERVO-DRIVE for LEGRABOX/TANDEMBOX ◀
Applications ◀◀
Motion technologies
Standard cabinet
Front assembly – position of Blum distance
bumper
Back cabling
BT
Drilling depth
The Blum distance bumper creates and
maintains the required trigger path of 2 mm.
When using a 70 kg LEGRABOX or 65 kg
TANDEMBOX runner, attach four Blum distance
bumpers. For optimal trigger function for front
height FH > 300 mm, use front stabilisation
FA Front overlay
FH Front height
Alternative drilling pattern for PRO-CENTER
and MINIPRESS
BT Drilling depth
Position – drive unit
All back heights except height N
Box systems
X min. (mm)
LEGRABOX
45.0
TANDEMBOX
35.0
Y min. (mm)
68.5
63.5
Motion technologies
Planning – vertical cross member
Drilling pattern base
Lower cabling
LEGRABOX – back height N
Cabinet width KB (mm)
275–320
> 320
Back
X
Y
X
Y
(mm) (mm) (mm) (mm)
Chipboard back
–
–
45.0
42.0
SERVO-DRIVE with LEGRABOX with steel back height N not
possible
–
Not possible
TANDEMBOX – back height N
Cabinet width KB (mm)
275–320
Back
X
Y
(mm) (mm)
Chipboard back
35.0
55.5
Steel back
–
–
–
Not possible
LH
PL
> 320
X
(mm)
27.5
27.5
Y
(mm)
48.5
48.5
Internal cabinet height
Bracket profile length
Page instructions
Assembly
Assembly – Blum distance bumper
Assembly – Blum transformer 72 W
Cabling
Catalogue 2016/2017 • KA-120
582
582
584
585
561