Nemo Invex Travel Pro
May 2013
NEVER SETTLE FOR ANYTHING LESS THAN EXCELLENCE. NEMO NETWORK TESTING SOLUTIONS
NEMO INVEX TRAVEL PRO
Hardware
•
•
•
•
•
Measurement/ transport case for
benchmarking system
Includes space for the following hardware:
• Nemo Invex active chassis (1pcs)
• VQ modules (12 pcs)
• UE/ Holders (12pcs)
• Nemo FSR1 scanner (1pcs,
optional)
• Place for pwr cables/ AC/DC
inverter
• Place for RF dividers (optional)
• Can be used also with HIM and
UIM modules (e.g. 3xHIM +
3xUIM)
• Other accessories
Estimated weight of fully loaded system is
~25- 35kg
Can be used also with external antennas
(optional)
Estimated time of release end of May 2013
NEMO INVEX TRAVEL PRO
Case
•
Based on high quality Pelican 1620 case
• Exterior dimensions:
• 626 x 492 x 350mm (24.64" x 19.39" x 13.78“)
• Interior dimensions:
• 545 x 417 x 318 mm (21.48" x 16.42" x 12.54“)
• Empty weight 9,62kg (21.2 lbs.)
• Compliant with CEI IEC 529 specification (Dust, post dust & immersion tests)
May 15, 2013
3
NEMO INVEX TRAVEL PRO
Main Frame
•
•
•
•
All hardwares are fixed to mechanical
frame what can be lifted up/ pushed
down using gas springs
Lockable main frame
By lifting up the main frame user have
access to operate switches, observe
LEDs, change cables etc.
Standard compliance:
• ETSI 300 019-2-2 v2.1.2
• Part 1-2: Classification of
environmental conditions;
Transportation
• Class 2.3 is a combination of
classes 2K4/2B2/2C2/2S2/2M2 in
IEC 60721-3-2
15.5.2013
NEMO INVEX TRAVEL PRO
Structure of Main Frame
FSR 1
scanner
Main frame consist of three
different levels:
Top level/ lid:
Nemo FSR1 scanner
receiver (1pcs)
• UE holders (12 pcs)
6 holders on the lid
Top
level
•
Middle
level
Middle level:
•
•
•
Nemo Invex active chassis (1
pcs)
AC Power supply (1pcs)
RF dividers (max. 6 pcs)
Bottom level:
•
VQ modules (max. 12 pcs)
15.5.2013
Invex
RF dividers
AC
power
VQ
modules
Bottom
level
6
May 15, 2013
7
May 15, 2013
8
May 15, 2013
9
May 15, 2013
NEMO INVEX TRAVEL PRO
Configuration Examples
15.5.2013
•
12 x UE handsets (voice/ data) + FSR1
NEMO INVEX TRAVEL PRO
Configuration Examples
15.5.2013
•
12 x UE handsets (voice quality/ data)
+ FSR1
NEMO INVEX TRAVEL PRO
Configuration Examples
15.5.2013
•
6 x UE handsets (voice/ data) + 6 x UE
(modems) + FSR1
NEMO INVEX TRAVEL PRO
Configuration Examples
15.5.2013
•
•
•
•
3 x voice quality + 3 x data
3 x HIM + 3 x UIM + FSR1
3 x RF combiners (1:4)
No holders installed
NEMO INVEX TRAVEL PRO
Versions & Options
Nemo Invex Travel Pro Standard 3x3ISO
ITP1100-00
• Travel Pro with Nemo Invex active Chassis. 3 x
HIM, 3 x UIM. 3 x RF combiners + accessories
• Holders not installed
Nemo Invex Travel Pro 12
ITP1100-01
• Travel Pro with Nemo Invex active chassis. Place
for 12 Ues + accessories
Nemo Invex Travel Pro Scanner Kit (FSR1 only)
ITP1101-00
ITP1102-00
• Scanner power, data and GPS RF cables (1pcs)
• FSR1 scanner puchased separately
Nemo Invex Travel Pro VQ Module Kit
(Nokia C5/ C7 Only)
• Nemo Invex VQ module, data and audio cables
(1-12 pcs)
Nemo Invex Travel Pro 4-Way RF Divider Kit
ITP1103-00
• 4-way RF Splitter (for four or two UEs)
• SMA 50 ohm loads, RF cables and magnetic
antenna. (1-6 pcs)
NEMO INVEX TRAVEL PRO
Building Configurations
Nemo Invex Travel Pro Standard 3x3ISO
•
•
•
•
ITP1100-00
External antennas are needed
Isolation modules are needed
3 x voice/ voice quality + 3 x data
Specify:
• UIC module (3 pcs)
• HIM module (3 pcs)
• UIM module (3pcs)
• Options:
• Nemo Invex Travel Pro Scanner Kit
Nemo Invex Travel Pro 12
ITP1100-01
• Base model for voice and data testing
• Specify number of UEs with/ without ext. antennas
• Specify number of UIC modules and models depending on number of UEs (1 UIC module per UE
or 2 x UE).
• Max. 6 x UIC modules as 6 x UIC modules can control up to 12 Ues. Depending also what
services will be tested. Consult Anite Finland helpdesk/ product management. E.g. 2 x
simultaneous Youtube testing cannot be done with one UIC module
• If ext. antennas are needed it’s recommended to use RF- dividers as case has limited space for
accessories. 2-4 x UEs per RF- divider. With LTE always two antennas are needed per UE. Only
two LTE UEs per one RF- divider. Max. 6 x RF dividers
• Possible to also mix and match HIM and UIM modules
• Options:
• Nemo Invex Travel Pro Scanner Kit
• Nemo Invex Travel Pro VQ Module Kit
NEMO INVEX TRAVEL PRO
Building Configurations
Nemo Invex Travel Pro Scanner Kit (FSR1 only)
ITP1101-00
• Kit includes only scanner power, data and GPS RF cables (1pcs)
• Nemo FSR1 scanner receiver must be purchased separately
• Specify:
• Down converter(s)
• All other scanner options
Nemo Invex Travel Pro VQ Module Kit
ITP1102-00
• Nemo Invex VQ module, data and audio cables (1-12 pcs)
• Supported with Nokia C5-00 and Nokia C7-00 handsets
• Specify number of kits. One kit per handset
NEMO INVEX TRAVEL PRO
Building Configurations
Nemo Invex Travel Pro 4-Way RF Divider Kit
ITP1103-00
•
•
•
•
•
4-way RF Splitter (for four or two UEs)
SMA 50 ohm loads, RF cables and magnetic antenna. (1-6 pcs)
Only to be used with UEs with ext. antenna cables
1-2 antennas per UE
Scanner antennas and UE antennas must not be connected to the same 4-way RF divider
COMPLETE TOOLSET FOR WIRELESS NETWORK TESTING
www.anite.com/nemo