Integrating New Holland PLM with
Raven & Rawson Controllers
Raven SCS 100 Series: 440/450/460/660
Raven SCS 1000 Series: 4000/4400/4600/5000
Rawson Accu-Rate Control System
Category: Precision Land Management
Series/Model: Integrating New Holland PLM with Raven & Rawson
Controllers
Document: PLM-10003-09
Date: January 2009
Precision Land Management
This is a Sale Education document not to be used for advertisement.
Specifications
Third Party Controller Capability
Raven and Rawson Rate Controllers
New Holland Precision Land Management products may be used in conjunction with Raven and Rawson variable rate controllers. Specific cables are available through New Holland Parts to communicate with Raven/Rawson controllers through the DB9 port and Tyco port of the IntelliView Plus II display. New Holland offers an operator’s manual for both third party controllers through the Document
Management Center. Please refer to “Raven Variable Rate Software for IntelliView Plus II Display”
operator’s manual for display set up and operation (87472173). Refer to “Rawson Accu-Rate Control
System Software for IntelliView Plus II Display” operator’s manual for display set up and operation
(87472174.
An important step prior to selecting the appropriate cable is to determine if the vehicle is IntelliSteer
ready. If it is not IntelliSteer ready or a non-New Holland vehicle a separate harness is required.
Additionally, a power source such as an auxilary fuse will suffice.
Compatible Models - Raven
The following Raven systems are supported using an RS-232 serial connection in conjunction with
the data menu settings listed in the chart below.
• SCS 100 series: 440/450/460/660 and other variants
• SCS 1000 series: 4000/4400/4600/5000 and other variants
Function
Baud Rate
Trigger Value
Trigger Units
GPS Functions
Decimals
Data Direction*
Datalog Mode*
Variable Rate Control**
Setting
9600
1
1 sec
Disabled
Unshifted
Com port
Console Data
On
*4400/4600 models only
**4400/4600/5000 models only
A null modem serial cable is required to connect to the Raven Control System to the IntelliView Plus II
display.
Raven Part Number
•
•
115-0159-624 for the Raven 100 series
115-0171-395 for the Raven 1000 series
Specifications
IntelliView Plus II Required Software
Raven
• Raven Controller 16.1.0.0
• Com3 Manager 16.1.0.0
• As Applied 16.2.0.0
• Precision Farming 16.2.0.0
• Generic Tractor 16.2.0.0 or Large Tractor 16.1.0.0
• Framework 16.4.0.0
Rawson
• Rawson Controller 16.1.0.0
• Com3 Manager 16.1.0.0
• As Applied 16.2.0.0
• Pecision Farming 16.2.0.0
• Generic Tractor 16.2.0.0 or Large Tractor 16.1.0.0
• Framework 16.4.0.0
New Holland Tractor Compatibility by Serial Number and IntelliSteer Option
New Holland Tractor Serial Break - IntelliSteer Ready
Model
T7000
T8000
T9000
Serial Number
Z6RW04319 and above
Z6RW04319 and above
Z7F202169 and above
Harness Part Number
87732647
87732647
87732647
New Holland Tractor Serial Break - Non-IntelliSteer Ready*
Model
TG/T8000
TJ/T9000
Serial Number
Z6RW01001 - Z6RW04319
Z6RW01001 and below
Z6F200013 - Z7F202169
Z6F200013 - and below
Harness Part Number
84169716
84169716
84169716
84169716
*Must install appropriate ISO11783 harness, mounting brackets and IntelliView Plus II display on New
Holland tractors not equipped IntelliSteer ready from factory in addition to listed harness.
Note - if auto guidance is not desired, the steering sensor, hydraulic manifold and hoses are not required to be installed.
Specifications
Communicating with third party variable rate controller via IntelliView Plus II
IntelliSteer ready tractor
OR
OR
Rawson Accu-Rate
Com Port A
Com Port B
(DB9 male connection)
(DB9 male connection)
Harness p/n 87732647
Raven SCS 1000 series
4000/4400/4600/5000
Raven SCS 100 series
440/450/460/660
*Both female com ports are
found on the third party controller
IntelliView Plus II
Tyco Connector *Plugs
into IntelliView Plus
II. This is com port A
- RS232
14
*Wires must be insterted into
appropriate cavity in Tyco
connector. This is com port
A - RS232
10 13
Com Port
*DB9 female connection found
next to Amp connector on IntelliView Plus II. This is com port
B - RS232
*If using IntelliSteer auto guidance, tractor must have NH162, NH252 or NH262 receiver and NAVII
controller installed per manufacturer specification. Auto guidance must be configured through IntelliView Plus II display.
Specifications
Communicating with third party variable rate controller via IntelliView Plus II
• Non-IntelliSteer ready New Holland tractor
• New Holland vehicle using an IntelliView Plus II display
with an NH100, NH162, NH252 or NH262
*If using IntelliSteer auto guidance, tractor must
have NH162, NH252 or NH262 receiver and NAVII
controller installed per manufacturer specification.
Auto guidance must be configured through IntelliView Plus II display.
Power Supply
Switched 12V + and clean
ground. *Not used in this
application
IntelliView Plus II
GPS Connection
Metripack female connector to GPS harness
Diagnostic Port Connector
CAN Terminator
Harness p/n 84169716
Connects CAN, 12V+ and
clean ground
Com Port
Tyco Connector
*Plugs into IntelliView Plus II. This is
com port A - RS232
Com Port
*DB9 female connection
on IntelliView II. This is
com port B - RS232
Clean ground
connection
*DB9 male connection
on rate controller. This
is com port A - RS232
Com Port
*DB9 male connection
on rate controller. This
is com port B - RS232
*Both female com ports are found
on the third party controller
OR
Rawson Accu-Rate
OR
Raven SCS 100 series
440/450/460/660
Raven SCS 1000 series
4000/4400/4600/5000
Specifications
Communicating with third party variable rate controller via IntelliView Plus II
• Non-New Holland vehicle using an IntelliView Plus II
display with an NH100, NH162, NH252 or NH262
Power Supply
Switched 12V + and clean
ground. Must be wired to
12V source such as auxillary fuse panel or cigarette
lighter
*If using a NH100, NH162, NH252 or NH262
receiver measurements must be recorded and
entered into IntelliView Plus II display.
IntelliView Plus II
GPS Connection
Metripack female connector to GPS harness
Diagnostic Port Connector
CAN Terminator
Harness p/n 84169716
Connects CAN, 12V+ and
clean ground. *Not used
in this application
Com Port
Tyco Connector
*Plugs into IntelliView Plus II. This is
com port A - RS232
Com Port
*DB9 female connection
on IntelliView II. This is
com port B - RS232
Clean ground
connection
*DB9 male connection
on rate controller. This
is com port A - RS232
Com Port
*DB9 male connection
on rate controller. This
is com port B - RS232
*Both female com ports are found
on the third party controller
OR
Rawson Accu-Rate
OR
Raven SCS 100 series
440/450/460/660
Raven SCS 1000 series
4000/4400/4600/5000
Notes
Additional Notes
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
The information presented herein is intended for sales education purposes and is intended for
the use of CNH Global N.V., its affiliates, and its independent dealers only. This information is
to be treated as CONFIDENTIAL and is not to be used for advertising purposes. Competitive
comparisons are based on competitive information known at time of printing. Sources of information include published industry specifications and data. General statements made herein
are the opinions of the authors concluded from supporting data.
Note:
Specifications are stated in accordance with industry standards or recommended
practices, where applicable.
Any trademarks referred to herein in association with the goods and/or services
of companies other than CNH Global
N.V. are the property of these respective
companies.
New Holland is a registered trademark of
CNH Global N.V.
This Sales Education Document has been published for worldwide circulation. The availability
of some models and equipment builds vary according to the country in which the equipment is
used and sold. The illustrations and text may include optional equipment and accessories and
may not include all standard equipment. For more information about the current standard and
optional equipment offered for your sales area, consult the published price listings.
Important
CNH Global N.V. reserves the right to change product specifications without notice and without incurring any obligation relating to such changes.
CNH ORIGINAL PARTS ENGINEERED FOR NEW HOLLAND EQUIPMENT. SUPERIOR QUALITY, GLOBAL SUPPORT.
COM-10002-08
© 2008 CNH Global N.V.
All Rights Reserved. Printed in U.S.A.
www.newholland.com