Wiring Instructions for
Class 1 LED Power Supplies to LED Modules
Installation Guide
Wiring Block Diagram
RED (V+)
BLACK (V-)
AC INPUT (3*AWG #18)
DC OUTPUT (2*AWG #18)
LED Module
Class 1 Power Supply Types
• LED modules MUST be wired in multiple strings.
• Number of modules per string cannot exceed the maximum specified below.
• Total number of modules per power supply are specified below.
100W
Power Supply Load Chart
100W
150W
DC OUTPUT
(2*AWG #18)
AC INPUT
(3*AWG #18)
220W
LED Module
Maximum # of
Modules per String
Total # of
Modules
Maximum # of
Modules per String
Total # of
Modules
Maximum # of
Modules per String
Total # of
Modules
BASE
CORE
APEX
CORE XTRA
APEX XTRA
COLOR (R,G,B)
COLOR (Y,O)
MINI
120
120
36
60
48
120
120
120
208
208
56
100
75
187
136
268
120
120
36
60
48
120
120
120
313
313
83
150
113
281
205
402
120
120
36
60
48
120
120
120
458
458
122
220
165
412
300
589
RED (V+)
BLACK (V-)
150W
AC INPUT
(3*AWG #18)
DC OUTPUT
(2*AWG #18)
L (BLK)
INP UT
100-277 VA C
MAXIMUM DISTANCE*
Wire Gauge (AWG) STANDARD (ft)
18
18
16
29
14
45
12
71
10
120
METRIC (m)
5.5
8.8
13.7
21.6
36.6
Power Distribution
Block
V+ (RED)
L E D P o we r S u p p l y PS12-150W-100-277V
I nput V ol t age
E345769
I nput Current
N(WHT)
(GRN)
C u sto me r Se rvi ce :1 -8 6 6 -4 8 2 -0 2 0 3
C onstant Voltage Type
100-277 V A C 50/ 60 Hz Output V ol t age
11.4-12.6DC
Output Current
0-12.5 A DC
1.75 A @ 100V A C
tc:90°C
For dry, damp and wet locations
12 V DC
V- (BLK)
RED (V+)
BLACK (V-)
DC OUTPUT
(2*AWG #18)
AC INPUT
(3*AWG #18)
L (BLK)
General LED ,Inc.
INP UT
100-277 VA C
V+ (RED)
L E D P o we r S u p p l y PS12-220W-100-277V
E345769
I nput V ol t age
I nput Current
N(WHT)
C u sto me r Se rvi ce :1 -8 6 6 -4 8 2 -0 2 0 3
C onstant Voltage Type
tc:90°C
100-277 V A C 50/ 60 Hz Output V ol t age
2. 8 A @ 100V A C
Output Current
11.4-12.6DC
OUTPUT
12 V DC
0-18.33 A DC
For dry, damp and wet locations
V- (BLK)
RED (V+)
BLACK (V-)
Troubleshooting
Problems
All LED modules are OFF or some of
the LED modules are not illuminated
Entire section does not light or lights
intermittently
LEDs flicker or appear dim
*Distance from power supply to first LED module of the string
(at full capacity)
General LED Power Supply
Possible Causes
1. No power to power supply
2. Wrong voltage power supply
3. Bad/Loose connection
4. LED modules connected in reverse polarity
1. Bad/Loose/Improper connections
2. Power supplies spaced too close together
1. Power supply may not be loaded properly with LED modules
2. Power supply may be damaged or defective.
• The maximum case temperature shall not exceed 88ºC when used in end product. • The maximum leakage current measured from the metal enclosure is 0.76 mA. This needs to • These products are intended for use in dry and damp locations.
• These products are intended to be connected to a max. 20 A branch circuit.
be considered if the end product is cord and plug connected.
AgiLight, Inc., a Division of General LED, Inc. +1.866.482.0203
OUTPUT
220W
(GRN)
Jumper Wire Gauge Chart
General LED ,Inc.
www.AgiLight.com
www.GenLEDLighting.com
www.GeneralLED.com
WARNING
RISK OF ELECTRICAL SHOCK
Turn OFF power before
perfoming any maintenance.
© 2013 General LED, Inc. 2013 All rights reserved.
Product Specifications subject to change without notice. 02-2013