TRACK TECHNICAL DETAILS and FITTING INSTRUCTIONS
SYSTEM 16 CEILING
Top fix only
10kg/m fixed at 60cm spacing
directly into ceiling/topboard
B R A C K E T S PA C I N G
Max
60cm
Max
8cm
16mm
19mm
SYSTEM 30 STRAIGHT
Top fix or face fix
kg/m with standard brackets
15kg/m with heavy duty brackets
B R A C K E T S PA C I N G
Max 120cm
Max 8cm
30mm
19mm
SYSTEM 30 BENDABLE
Top fix or face fix
10kg/m with brackets
either side of every bend,
max spacing 60cm
B R A C K E T S PA C I N G
* A bracket is required either side of every bend
Max 60cm
Max
60cm
30mm
19mm
* Two brackets are required at the track ends
Tel: 01404 47568 Email: [email protected] www.cameronfuller.co.uk © cameronfuller 2016 v1
1
SYSTEM 16 CEILING
TOP FIXING ONLY.
NO FACE FIXING OPTION
Drill using drill guide
and 4mm drill bit (supplied)
or order pre-drilled from us
No brackets required
Fit track directly to ceiling / top board
Not suitable for bending
SYSTEM 30 STRAIGHT
TOP FIXING
Back
Front
FACE FIX BRACKETS FOR SYSTEM 30
Fit track directly to ceiling
or top board, using
pre-drilled holes
Drill using drill guide
and 4mm drill-bit (supplied)
or order pre-drilled from us
No brackets required
See page 8 for bracket sizes
SYSTEM 30 BENDABLE
TOP FIXING
FACE FIX BRACKETS FOR SYSTEM 30
Fit track directly to ceiling
or top board, using
pre-drilled holes
Back
No brackets required
Front
See page 8 for bracket sizes
Use pre-drilled holes
IMPORTANT
When top fixing bendable track, DO NOT
over tighten screws as this can deform the
track and cause the gliders to jam
2
SYSTEM 16 CEILING
No finials / end caps
Join using straight joiner
SYS T E M 3 0 S T R A I G H T J O I N E R
FINIALS
Ensure magnet is at the front of the track
so that the cover plate will locate correctly
The finials below are for System 30 straight
and bendable only
Ice finial
30mm
100mm
Magnet
Square Barrel finial
Magnet
30mm
Magnet
Cover
plate
Suitable
for use
with
top fix
100mm
Collar finial
30mm
50mm
SYS T E M 3 0 B E N DA B L E J O I N E R
Cap finial
30mm
25mm
Torus finial
Magnet
Magnet
NOT
Suitable
for use
with
topfix
60mm
85mm
Ball finial
60mm
85mm
Remove part of the inner plastic section to
create space to insert the joiner
Ensure magnet is at the front of the track
so that the cover plate will locate correctly
3
BENDING SYSTEM 30
Easy to bend on site at point of installation. No more measuring up and hoping.
No transporting awkward and delicate bent tracks
Fo
rm
10 er r
0m ad
m ius
Tr
ac
15 k ra
0m diu
m s
Former with spring back gives a track bend
radius of 150mm (we can supply this former)
Bend track until kerfs touch.
Do not bend any further
It’s easy to achieve:
Radius 150
Radius 150
FORWARD BENDS
REVERSE BENDS
CONTINUOUS BENDS
Bend A
All tracks over 2.4m long are supplied in 2 pieces.
The track should be joined in the middle of the
centre window.
Bend A
Window
centre
Bend B
Trim
here
Bend B
Trim
Bend C here
Bend C
Joiner
Diagram shows track joiner attaching
two track lengths at the window centre
B E N D I N G T O F I T A B AY
1
Identify front and back of track
3
Bend from the centre working outwards.
Bend A, then B, then C, one side then A-C
on the other side
4
Trim off excess track at the track ends
5
Bracket spacing - see front page
Back
Front
2
4
Insert joiner, pushing the plastic filler
down the track and tighten screws
B E N D I N G SYS T E M 3 0
Bend towards the straight end
NOT LIKE THIS
Open end
Former
DO NOT try to bend towards another bend
This method causes internal stress
in the track which can cause
the gliders to jam
Former
Open end
JOINING ALL TRACKS
1
Join together factory cut ends and trim off the excess at track ends only
Uncut factory ends
Trim ends and cover with end caps/finials
Uncut factory ends
Uncut factory ends
2
Place a support bracket as close as possible to the join
3
Ensure the joins are butted together tightly before tightening lock screws
With careful installation gliders will smoothly pass over the track joins.
There is no limit to maximum track length
5
TRACK CORDING INSTRUCTIONS
Return pulley
Down pulley
S I N G L E C O R D , S I N G L E C U R TA I N
For a single curtain you will need in
addition to hand-drawn componants:
– 1 x down pulley
– 1 x return pulley
– 1 x cord tensioner
– 1 x overlap arm
– cord (2 x track length
and 2 x cord drop)
Cord
drop
Note: Child safety regulations state:
Cord loop should be installed at
least 1.5m from the floor
Cap end or
any finial
Min 1.5m
Knotted ends
Tensioner
S I N G L E C O R D , P A I R O F C U R TA I N S
For a pair of curtains controlled by
a single cord you will need:
– 1 x down pulley
– 1 x return pulley
– 1 x cord tensioner
– 1 x overlap arm
– 1 x underlap arm
– cord (2 x track length
and 2 x cord drop)
Cord
drop
Underlap arm
Overlap arm
Knotted ends
Min 1.5m
Tensioner
D U A L C O R D , P A I R O F C U R TA I N S
For a dual controlled pair
of curtains, you will need:
– 2 x down pulleys
– 2 x return pulley
– 2 x cord tensioner
– 1 x overlap arm
– 1 x underlap arm
– cord (2 x track length
and 4 x cord drop)
Cord
drop
Underlap arm Overlap arm
Min 1.5m
Knotted ends
Tensioner
OVERLAP AND UNDERLAP DIMENSIONS
Under lap
Overlap
100
6
100
Knotted ends
Tensioner
CAMERON FULLER ‘SURF’ GLIDERS
SURF 60
SURF 80
60mm
80mm
Standard wall brackets will allow curtains
to stack back correctly with SURF 60
MAGNETIC GLIDER BRAKE
Use adjustable 75 -105 wall brackets to allow
curtains to stack back correctly with SURF 80
to ensure curtains stay stacked back
Adjustable glider stop
Lead glider with magnet
D R AW R O D C A R R I E R
T W I S T S TO P E N D S
Drawrod carrier
Drawrod
C U R TA I N H E A D I N G S
We recommend curtain headings should be underslung for all
three tracks to ensure the best operation of the curtains
10mm
7
BRACKETS AND FITTINGS
FA C E F I X B R A C K E TS F O R S YS T E M 3 0
All dimensions are in mm
57
110 -150
41
50
50
57
57
Cover
Standard bracket
Cover
Heavy duty adjustable 110 -150 bracket
140
75 -110
55
50
30
50
57
57
Cover
Heavy duty adjustable 75 -110 bracket
DIRECT CEILING FIX
F O R A L L T R A C KS
Cover
Double track bracket
LO N G C E I L I N G
S TA N D O F F
30
Front
8
Back
Adjustable
80 -680mm
Designed by www.aliasdesign.co.uk
For System 30,
NOT System 16