The Anatomy of Your Device
1.
2.
3.
4.
1.
2.
4.
Control Panel: Contains activation button
and touch sensor for voltage and brightness
settings
LED Power Indicator: Corresponding rows
of LED lights located on either side of the
battery glow to show you how much
charge is remaining
Cartridge Chamber: Magnetically secures
your cartridge
Magnetic Charge Port: Connects to the
USB charger
Charging
VERTX Plus arrives with a partial charge, so make
sure you completely charge it before its initiation.
Plug the included charger into a USB port and
connect the magnetic head to the metal port on
the end of your battery.
The activation button and the LED power indicator
will flash three times, indicating that VERTX Plus is
charging. As it charges, the lights on the power
indicator will cycle intermittently; all five LEDs will
glow white when VERTX Plus is fully charged.
As you use VERTX Plus, the five glowing LED lights
of the power indicator will gradually dim, one at a
time, to reflect the charge remaining. When there
are only two LEDs still glowing, they will change
from white to red, signifying that you have less than
30% charge remaining in the battery. But this
doesn’t have to interrupt your enjoyment – VERTX
Plus was designed for use while charging. Simply
connect your battery to the USB charger and
continue normal use.
USER MANUAL
Genuine. Satisfaction.
™
Warranty
For details on the V2® VERTX Plus Limited Warranty,
please go to: www.v2.com
Genuine. Satisfaction.
™
Visit V2.com to:
• Download your free E-Liquid Quality Assurance Report.
• Reference our complete User Manual.
• View a detailed list of all e-liquid ingredients.
• Access the V2 Store Locator to find V2 retail locations near
®
®
you.
• Browse the entire V2
®
collection and enroll in our customer
rewards program: Vape 4 Free.
Should you have any questions regarding our Limited Warranty
or need to request a replacement on an electrical component,
please contact our Customer Service Department, toll-free at:
1.877.37.VAPOR (1.877.378.2767)
Designed by V2® in the USA. Assembled in China © V2®
Intellectual Property Rights: vmrproducts.com/ip
1.1.3
3.
Initiating Your Device
Setting the Voltage and Brightness
1. Remove VERTX Plus from its packaging.
VERTX Plus is the only microcig on the market to offer variable voltage
settings; a feature that has historically been limited to larger, “tank”-like
devices. The ability to choose your preferred voltage gives you greater
control over your vapor experience. It allows you to adjust your device
so it heats to optimum temperature for every variety of e-liquid.
There are three settings to choose from: High (4.5v), Medium (4.0v)
and Low (3.5v). VERTX offers an additional level of customization with
variable brightness settings, allowing you to choose how brightly its lit
components glow. The three light output settings include Bright
(100%), Moderate (50%) and Stealth (0%*). Both voltage and
brightness settings are accessed via the control panel.
2. Charge VERTX Plus using the included USB charger.
3. Slide the cartridge into the recessed cartridge chamber.
4. Unlock VERTX Plus by pressing the activation button three times
within two seconds.
5. Press and hold the activation button to begin puffing.
Locking and Unlocking VERTX Plus
Like your cell phone, VERTX Plus has a lock feature to prevent
accidental activation. Push the activation button three times within two
seconds and you’ll see the button and LED power indicators flash
three times. This will lock VERTX Plus and render it unresponsive to
accidental actions when not in use. To unlock, push the activation
button three times within two seconds. The activation button and LED
power indicators will flash three times, signifying that VERTX Plus is
ready to use.
Vertx Cartridges
Your VERTX Plus kit comes with one VERTX cartridge which
is either prefilled or blank. Prefilled VERTX cartridges are
disposable and can simply be replaced when the e-liquid
inside runs out. Your VERTX cartridge has a 1.2ml capacity
and delivers a puff count of up to 650, when used on the
lowest voltage setting. Available in multiple V2 Flavors.
VERTX Blank Cartridges are reusable and can be filled with
the premium e-liquid of your choice. To fill your VERTX
Blank Cartridge, simply slide back the mouthpiece and
drip e-liquid into the hollow chamber. Be sure not to fill
beyond the full line.
*In Stealth mode, the light output for the LED power indicator is 0%;
the control panel output is 15%.
Voltage:
1.
Make sure VERTX Plus is unlocked.
2. Press the activation button two times. This will put VERTX Plus into
Mode Selection. (You will see the activation button and LED
power indicator lights pulse.)
3. At the bottom of the control panel, the lightning bolt icon
(voltage) and the sun icon (brightness) will cycle, with one
glowing and then the other. To select voltage, press the
activation button once when the lightning bolt icon is glowing.
Brightness:
1. Make sure VERTX Plus is unlocked.
2. Press the activation button two times to put VERTX Plus into Mode
Selection. (You will see the activation button and LED power
indicator lights pulse.)
3. At the bottom of the control panel, the lightning bolt icon (voltage)
and the sun icon (brightness) will cycle, with one glowing and then
the other. To select brightness, press the activation button once
when the sun icon is glowing.
4. Using your finger, swipe the sensor located inside the control
panel. Swiping upwards increases the voltage; swiping
downwards lowers it. The glowing sensor lights correspond
with each of the three voltage settings: three lights indicate High,
two lights indicate Medium, and one light indicates Low.
4. Using your finger, swipe the sensor located inside the control
panel. Swiping upwards increases the brightness; swiping
downwards lowers it. The glowing sensor lights correspond with
each of the three brightness settings: three lights indicate Bright,
two lights indicate Moderate, and one light indicates Stealth.
5. When you have reached your desired voltage setting, press the
activation button once to resume normal use.
5. When you have reached your desired brightness setting, press
the activation button once to resume normal use.