59 1/16” dia twelve sided sump with collar ring base. corbel, skirt, non structural
internal lid with dipstick hole. 42” dia flat sealed black cover with central sealed cover
and frame. Designed for a remote fill line with a central dip.
For reference purposes only. This drawing is not a
specification. Order against product code only. To
enable continuous improvement of our products, the
designs and specifications are subject to change
without notice.
S16CR-3100-CD
Page: 1 of 4
Issue: 12/06/2016
© Copyright
FILL COVER
FL100/CD COVER
LY
N
O
IP L
D IL
L F
A T
U O
N N
A O
M D
FL100 FRAME
FL100/SK250
NON STRUCTURAL INTERNAL LID
S/LID/ROUND/100/CD
SELF LEVELLING
ADHESIVE SEALANT
(FOR USE ON HIGH WATER
TABLE APPLICATIONS)
SPOUT
CONDENSATION BOTTLE
BOTTLE CARRIER
S16-3100/CORBEL
HANGER
FOAM BLOCK
S16CR CHAMBER
59 1/16” dia twelve sided sump with collar ring base. corbel, skirt, non structural
internal lid with dipstick hole. 42” dia flat sealed black cover with central sealed cover
and frame. Designed for a remote fill line with a central dip.
For reference purposes only. This drawing is not a
specification. Order against product code only. To
enable continuous improvement of our products, the
designs and specifications are subject to change
without notice.
S16CR-3100-CD
Page: 2 of 4
Issue: 12/06/2016
© Copyright
PCD 21 21/32
40 5/32
38
MAX. 11 13/16
MIN. 7 7/8
1
3 17/32
6 7/8
13
MAXIMUM TRIM POINT
25/32
6 7/8
Max. 56 3/16
Min. 33 15/32
59 11/16 A/F
11 13/16
MAXIMUM TRIM POINT
29 17/32
CL
37 13/32
59 1/16 A/F
59 1/16” dia twelve sided sump with collar ring base. corbel, skirt, non structural
internal lid with dipstick hole. 42” dia flat sealed black cover with central sealed cover
and frame. Designed for a remote fill line with a central dip.
For reference purposes only. This drawing is not a
specification. Order against product code only. To
enable continuous improvement of our products, the
designs and specifications are subject to change
without notice.
S16CR-3100-CD
Page: 3 of 4
Issue: 12/06/2016
© Copyright
VERY IMPORTANT
OUTER EDGE "A" OF FRAME SET 3/16”- 13/32”
ABOVE GENERAL FORECOURT AREA WITH
CONCRETE RAMPED AWAY OVER 11 13/16”.
TYPICAL INSTALLATION
CONCRETE
VERY IMPORTANT
The underside of the frame
must be adequately
supported by concrete.
"A"
3/16”- 13/32”
11 13/16”
Expansion joint filled
with petrol resistant
mastic.
FL100CD COVER
19 11/16”
Minimum
7 7/8“
Maximum
13 25/32“
Joint tied with
23 5/8“ long x 15/32“
dowel at 23 5/8“ c/c.
Half bonded
Concrete reinforced
CORBEL with 2 layers of
reinforcement mesh.
S16CR CHAMBER
TARMACADAM
PEA GRAVEL
CONCRETE
SAND
ALTERNATIVE INSTALLATION ADVICE
TARMACADAM
TARMACADAM
(THICKNESS AS SPECIFIED) 3/16
A
11
19 11/16”
13/16
1
Minimum
7 7/8“
Maximum
13 25/32“
A
SETTS
3/16
Minimum
7 7/8“
Maximum
13 25/32“
19 11/16”
11 13/16
5 1/8
5 3/16
59 1/16” dia twelve sided sump with collar ring base. corbel, skirt, non structural
internal lid with dipstick hole. 42” dia flat sealed black cover with central sealed cover
and frame. Designed for a remote fill line with a central dip.
For reference purposes only. This drawing is not a
specification. Order against product code only. To
enable continuous improvement of our products, the
designs and specifications are subject to change
without notice.
S16CR-3100-CD
Page: 4 of 4
Issue: 12/06/2016
SETTS
1
© Copyright