www.alltemp.ca
Introducing an All New Line of
Cleaning Chemicals
Coil Cleaners & Brighteners
Metal Cleaning Detergents
Ice Machine Cleaners
Scale Removers
Electronic Cell Cleaner
Degreasing Solvent
Leak Detector
Coil Cleaner & Brighteners
Acid Based - Concentrate
Coil Cleaner & Brightener Acid Based –
Concentrate is used for cleaning air-cooled
condensers and coils. It generates foam, which
drives contamination out of the condenser.
Product is easily rinsed away with water.
•For outdoor use only. Recommend wearing protective eyewear and
gloves while using this product.
•Turn power off.
•Mix with equal parts of water.
•Apply using low pressure sprayer. Add water first to sprayer and
then add an equal amount of Coil Cleaner & Brightener Acid Based –
Concentrate.
•For heavy dirt, use 1 part cleaner to 3 parts fresh water. For moderate
dirt, use 1 part cleaner to 10 parts fresh water.
•Wait 3 to 5 minutes.
•Rinse thoroughly with fresh water.
NOTE: Do not use Coil Cleaner & Brightener Acid Based – Concentrate undiluted or any stronger than
one part cleaner to two parts fresh water for cleaning coils. Avoid use on nickel and aluminum metals.
Part #
15-CCAB-1G
Description
Coil cleaner & brightener acid based concentrate - 1 Gal - 4 per case
Non Acid Based - Concentrate
Coil Cleaner & Brightener Non Acid –
Concentrate is used for cleaning tube and fin
assemblies in air conditioning condensers.
Alkaline in nature, it includes surfactants,
which cut through heavy grease accumulations
caused by air borne contaminants. Contains
biodegradable chelants.
•For outdoor use only. Recommend wearing protective eye-wear and
gloves while using this product.
•Turn power off.
•Use 1 part Coil Cleaner & Brightener Non Acid – Concentrate to 3 parts
fresh water.
•Apply using a low-pressure sprayer. Add water to sprayer first, then Coil
Cleaner & Brightener Non Acid – Concentrate.
•Spray coils. Wait 5 to 10 minutes.
•Once cleaning is completed, rinse equipment thoroughly with fresh
water.
NOTE: Do not use on rubber roofs. Do not use on aluminum or aluminum coated metals. Do not use
Coil Cleaner & Brightener Non Acid – Concentrate undiluted or any stronger than 1 part cleaner to 3
parts water for cleaning coils.
Part #
15-CCNA-1G
Description
Coil cleaner & brightener non acid concentrate - 1 Gal - 4 per case
15-CCAB-5G
Coil cleaner & brightener acid based concentrate - 5 Gal - each
15-CCNA-5G
Coil cleaner & brightener non acid concentrate - 5 Gal - each
15-CCAB-DR
Coil cleaner & brightener acid based concentrate - 55 Gal - each
15-CCNA-DR
Coil cleaner & brightener non acid concentrate - 55 Gal - each
Coil Cleaner Heavy Duty & Coil Brightener
Coil Cleaner Heavy Duty - Concentrate
Coil Cleaner Heavy Duty – Concentrate is a self-rinsing
coil cleaner for cleaning evaporator coils. A blend
of surfactants, cleaners, degreasers and corrosion
inhibitors remove stubborn deposits. Product has selfrinsing power when the system produces considerable
amounts of condensation to facilitate rinsing.
•For outdoor use only. Recommend wearing protective eyewear and gloves
while using this product.
•Turn power off.
•Apply using a low-pressure sprayer. Use 1 part Coil Cleaner Heavy Duty – Concentrate
to 5 parts water. Add fresh water to sprayer first, and then add the cleaner.
•Spray cleaning solution onto dirty coils or evaporator plates. Make sure when
cleaning electronic air filters, to wet all surfaces of the plates with cleaning solution.
•For dirty coils, allow to remain in contact for 5 to 10 minutes. For plates, allow
to remain in contact for 5 to 15 minutes.
•Rinse thoroughly with water. If the unit is equipped with sprayers, use for
rinsing the system. If hot water is available, use instead of cold water.
•For self-rinsing, dilute 1 part Coil Cleaner Heavy Duty – Concentrate to 40 parts water.
This is only effective when sufficient condensation is produced from the system.
Coil Brightener - Concentrate
Coil Brightener – Concentrate is used for
restoring brightness to aluminum condensers.
It removes oil, grease, and provides a mild
controlled etch of metal surface, which minimizes
metal loss while restoring surface brightness.
•For outdoor use only. Recommend wearing protective eyewear and
gloves while using this product.
•Turn off the power.
•Apply using low pressure sprayer. Add water first to sprayer and then
add an equal amount of Coil Brightener – Concentrate.
•Foaming will occur to push dirt outward from coils. For heavy dirt use
3 parts fresh water to one part cleaner. For moderate dirt use 10 parts
fresh water, to one part cleaner.
•Wait 3 to 5 minutes.
•Rinse thoroughly with fresh water.
NOTE: Do not use Coil Cleaner Heavy Duty – Concentrate undiluted or any stronger than one part
cleaner to three parts water for cleaning electronic air filters and coils.
Part #
15-CCHD-1G
Description
Coil cleaner heavy duty concentrate - 1 gal - 4 per case
Part #
15-CB-1G
Description
Coil brightener concentrate - 1 gal - 4 per case
15-CCHD-5G
Coil cleaner heavy duty concentrate - 5 gal - each
15-CB-5G
Coil brightener concentrate - 5 gal - each
15-CCHD-DR
Coil cleaner heavy duty concentrate - 55 gal - each
15-CB-DR
Coil brightener concentrate - 55 gal - each
Metal Cleaning Detergent
Concentrate
Metal Cleaning Detergent – Concentrate is a
multi-purpose cleaner formulated for rapid grime
penetration and removal. It is an economical
surfactant compound, which emulsifies and
removes grease, oil and carbon on most surfaces
including metal, ceramics, vinyl, rubber and
plastic. Most powerful when cleaner is soaked
in dirty area for 15 to 20 minutes and then
scrubbed using a brush before rinsing away.
•Recommend wearing protective eyewear and gloves while using this product.
•Mix 1 part cleaner to 4 parts fresh water. Add fresh water to sprayer
first, and then add the cleaner, mix well. Apply using a low-pressure
sprayer.
•Using sprayer, spray area to be cleaned.
•Allow to soak for 15 to 20 minutes, and then rinse thoroughly using
fresh water.
•For no rinse application, Metal Cleaning Detergent – Concentrate can
be used where sufficient condensation is generated. Dilute 10 parts of
water to 1 part cleaner
•Rinse thoroughly with fresh water.
Part #
15-MCD-1G
Description
Metal cleaning detergent concentrate - 1 gal - 4 per case
Heavy Duty - Concentrate
Metal Cleaning Detergent Heavy Duty –
Concentrate is a water based metal cleaning
detergent which removes stubborn grease
and other hard to remove deposits from
metal surfaces, fan blades, condensers, and
evaporators. Product has self-rinsing power
when the system produces considerable
amounts of condensation to facilitate rinsing.
•Recommend wearing protective eyewear and gloves while using this
product.
•Apply using a low-pressure sprayer. Mix 1 part cleaner to 4 parts water.
Add water to sprayer first, and then add the cleaner.
•Spray cleaning solution on plates. Be sure to wet all surfaces of the
plates thoroughly with cleaning solution.
•Allow cleaner to remain on plates for 5 to 15 minutes.
•Rinse thoroughly with fresh water. Fresh hot water provides best rinsing.
•On very dirty systems, it may be necessary to repeat steps 3 to 5.
•For no rinse application, Metal Cleaning Detergent Heavy Duty –
Concentrate can be used where sufficient condensate is generated.
Dilute 1 part cleaner to 10 parts fresh water.
Part #
15-MCHD-1G
Description
Metal cleaning detergent heavy duty concentrate - 1 gal - 4 per case
15-MCD-5G
Metal cleaning detergent concentrate - 5 gal - each
15-MCHD-5G
Metal cleaning detergent heavy duty concentrate - 5 gal - each
15-MCD-DR
Metal cleaning detergent concentrate - 55 gal - each
15-MCHD-DR Metal cleaning detergent heavy duty concentrate - 55 gal - each
Ice Machine Cleaner
Concentrate
Ice Machine Cleaner – Concentrate is formulated
for cleaning all types of ice machines including
cube, tube and flake. It can also be used to
descale commercial dishwashers and coffee
making units and is safe to use since it is
formulated with food grade materials.
•Recommend wearing protective eyewear and gloves while using this
product.
•Mix 8 ounces of Ice Machine Cleaner – Concentrate with 1.5 gallons
of fresh water.
•Circulate the cleaning solution for 1 hour.
•Heavy dirt may require brushing equipment with a concentrated
solution by mixing 8 oz. to 1 gallon fresh water.
•Drain cleaning solution.
•Rinse system with fresh water twice.
•Discard first batch of ice.
Part #
15-IML-16
Description
Ice machine cleaner concentrate - 16 oz - 12 per case
Metal Compatible(Nickel Safe) - Concentrate
Ice Machine Cleaner Metal Compatible –
Concentrate removes normal lime scale
formations, which are found in ice machines.
It is formulated for use on nickel and tin plate
evaporators.
•Recommend wearing protective eyewear and gloves while using this
product.
•Add 8 ounces of Ice Machine Cleaner Metal Compatible – Concentrate
with 1.5 gallons of fresh water.
•Circulate the cleaning solution for 1 hour.
•Heavy dirt may require brushing equipment with a concentrated
solution by mixing 8 oz. to 1 gallon fresh water.
•Drain cleaning solution.
•Rinse system with fresh water twice.
•Discard first batch of ice.
Part #
15-IMM-16
Description
Ice machine cleaner metal compatible (nickel safe)
concentrate - 16 oz - 12 per case
15-IML-1G
Ice machine cleaner concentrate - 1 gal - 4 per case
15-IMM-1G Ice machine cleaner metal compatible (nickel safe)
15-IML-5G
Ice machine cleaner concentrate - 5 gal - each
15-IMM-5G Ice machine cleaner metal compatible (nickel safe)
15-IML-DR
Ice machine cleaner concentrate - 55 gal - each
15-IMM-DR Ice machine cleaner metal compatible (nickel safe)
concentrate - 1 gal - 4 per case
concentrate - 5 gal - each
concentrate - 55 gal - each
Scale Remover - Concentrate
Concentrate
Scale Remover – Concentrate is an acid based solution for use on equipment with heavy scale build
up and includes low foaming corrosion inhibitors. Its fast penetration effectively dissolves hard to
remove build up of scale in cooling systems. An antifoam additive reduces foam during the cleaning
process to prevent wasted acid and ensure safety.
•Take care to remove sludge from sump, close the bleed line and refill with fresh water. Recommend wearing protective eyewear and gloves while
using this product.
•Combine 1 gallon Scale Remover – Concentrate to each 15 gallons of water.
•Start the pump and return to normal operation.
•Active cleaner is red in color and when neutralized becomes yellow. When the solution becomes yellow, more liquid scale remover is needed. Add
another dose equal to the first. Continue to repeat this process until cleaning solution has maintained the red color for 20 to 40 minutes.
•If you cannot see the cleaning solution, check solution with pH litmus strips every 15 to 20 minutes. If system contains a large amount of dirt and
debris, check solution with pH strips. (Refer to instruction card provided with pH strips.)
•Once cleaning is completed, in accordance with all applicable Federal, State and Local regulations drain the waste solution from system. (Do not
drain to lawns or where plants may be damaged.)
•Rinse out system by filling the system with fresh water twice.
•Refill sump, open bleed and resume to normal operation.
NOTE: Do not leave cleaning solution in system longer than necessary and not for more than 4 hours. Do not use on stainless steel or aluminum. Do not exceed recommended concentration when using for
cleaning galvanized metal, damage can result.
Part #
15-SRL-1G
Description
Scale remover concentrate - 1 gal - 4 per case
15-SRL-5G
Scale remover concentrate - 5 gal - each
15-SRL-DR
Scale remover concentrate - 55 gal - each
Scale Remover - Powder
Concentrate
Scale Remover – Powder is concentrated and acid based for use on equipment with heavy scale
build up. Product can be used to descale aluminum, stainless steel, and cast iron.
•Take care to remove sludge from sump, close the bleed line and refill with fresh water. Recommend wearing protective eyewear and gloves while
using this product.
•Use 2 pounds Scale Remover – Powder to each 15 gallons of fresh water.
•Start the pump and return to normal operation.
•Active cleaner is red in color and when neutralized becomes yellow. When the solution becomes yellow, more powdered scale remover is needed.
Add another dose equal to the first. Continue to repeat this process until cleaning solution has maintained the red color for 20 to 40 minutes.
•If you cannot see the cleaning solution, check solution with pH litmus strips every 15 to 20 minutes. If system contains a large amount of dirt and
debris so you cannot see the color, check solution with pH strips. (Refer to instruction card provided with pH strips.)
•Once cleaning is completed, in accordance with all applicable Federal, State and Local regulations drain the waste solution from system. (Do not
drain to lawns or where plants may be damaged.)
•Rinse out system by filling the system with fresh water twice.
•Refill sump and resume to normal operation.
NOTE: Do not leave cleaning solution in system longer than necessary and not for more than 4 hours. Safe to use powdered scale remover on steel, aluminum. and zinc.
Part #
15-SRP-10
15-SRP-45
Description
Scale remover powder - 10 lbs - each
Scale remover powder - 44 lbs - each
Electronic Cell Cleaner/Degreasing Solvent/Leak Detector
Electronic Cell Cleaner
Electronic Cell Cleaner is
formulated for the cleaning
of electronic cells and air
conditioning pre-filters.
Part #
15-ECC-16
Description
Electronic
cell cleaner
16 oz - 12
per case
15-ECC-5G Electronic
cell cleaner
5 gal - each
Degreasing Solvent
Degreasing Solvent is a solvent
based cleaner which provides
excellent cleaning power for
removing greases, oils, waxes,
and other organic compounds.
Part #
Description
15-DS-16-A Degreasing solvent -
16 oz - 12 per case
Gas Leak Detector
Gas Leak Detector allows for
pinpoint accuracy to locate leaks
and can be used on all pressurized
systems. It is specifically
formulated to detect leaks and
have longer foaming characteristics
and leave significantly less residue
than alternative basic “mild” soap
solutions.
Part #
Description
Gas leak detector 8 oz - 12 per case
15-GLD-1G Gas leak detector 1 gal - 4 per case
15-GLD-5G Gas leak detector 5 gal - each
15-GLD-DR Gas leak detector 55 gal - each
15-GLD-08