Co Co
lo rr
ur ec
in tiv
g e
Gu
id
e
Re-Colouring - Filling Options
Re-colouring pre-lightened hair with Infiniti permanent colour - refer to Colour Star & Underlying
pigment guide for detailed information.
Method
1. Evenly spray Sapphire Ice Defender to equalize porosity.
2. Mix as necessary (from table below) the required filler. Apply to damp hair ensuring sufficient
product is applied without overloading hair with pigment.
3. Blow-dry filler into hair. Mix required Permanent target shade + 3% Infiniti Developer (1 + 1.5).
Apply thoroughly & evenly to hair.
4. Process for 30 minutes no heat or 15 - 20 minutes gentle heat.
Infniti Permanent Colour Filler
Target Level
Infiniti Satin Tone on Tone Colour Filler
10
1 Part 10.3 + 1 Part Water
9
1 Part
8.3 + 1 Part .000 Clear + 2 Parts Water
1 Part 9.3 + 1 Part Water
8
2 Parts 8.3 + 1 Part .000 Clear + 3 Parts Water
1 Part 8.3 + 1 Part Water
7
1 Part
1 Part 7.43 + 1 Part Water
6
2 Parts 7.4 + 1 Part 7.3 + 3 Parts Water
1 Part 6.4 + 1 Part Water
5
1 Part 6.4 + 1 Part Water
1 Part 5.4 + 1 Part Water
4
1 Part 5.4 + 1 Part Water
1 Part 4.6 + 1 Part Water
3
1 Part 5.4 + 1 Part Water
1 Part 3.66 + 1 Part Water
2
1 Part 3.66 + 1 Part Water
1 Part 3.66 + 1 Part Water
1
1 Part 3.66 + 1 Part Water
8.3 + 1 Part Water
Corrective Colouring with Infiniti Coffee Shop Collection
These shades have inbuilt fillers and may be used alone for re-colouring and darkening.
Mixing
1 + 1.5 with 3% Infiniti
Developer
Processing Time
30 minutes no heat or
15 - 20 minutes gentle heat
Tip
When re-colouring 3 levels or darker use target
shade + 25% of the next darker shade to ensure
correct depth result
Infiniti Erase It & Infiniti Powder Lite - Colour Removal Options
Removing unwanted depth and tone - refer to Affinage Professional technical manual options for detailed
Infiniti Erase It and Infiniti Powder Lite.
Erase It - Colour Removal
Infiniti Erase It Method
Processing Time
Mixing Amounts 30ml + 30ml
Minimal Removal - Tone
Up to 20 Minutes
Equal Parts Phase 1 + 2
Depth & Tone Removal
Up to 30 Minutes or 20 Minutes with Heat
Equal Parts Phase 1 + 2
Heat assistance is recommended for processing when depth and tone reduction/removal is required. Refer to
Technical Manual for detailed instructions.
Processing
Detector Phase
Re-Colouration
Developer Selection
Process for required time (see
above), rinse thoroughly,apply
White Ice Deep Cleansing
Shampoo, rinse and follow
with detector phase
Use required quantity of 3%,
apply to erased areas and
leave for 5 minutes (check
regularly), rinse ready for recolouration (if desired)
Mix and apply chosen shade (1
-2 shades lighter than target)
to damp or dry hair, process up
to 30 minutes (may not require
full time).
Same depth adding
colour use 6%, 1-2
shades lift use 9%
Infiniti Developer
Colour Removal & After Care
At the completion of colour processing, emulsify colour paying particular attention to hairline areas. Rinse
until water runs clear, lightly shampoo with White Ice Treatment Shampoo and follow with White Ice Treatment
Conditioner.
It is recommended that a skin sensitivity test be completed 24-48 hours prior to the application or use of Affinage Professional
products
Technical Hotline 1800 804 757
www.affinage.com.au