Tariff
Description
===========================================================================
7222.19
BARS, stainless steel, square, having an across the flat dimension
NOT exceeding 50.8 mm
Op. 01.07.1996
Dec. 12.06.1996
- TC 9604143
7222.19
BARS, flat, stainless steel, in ANY of the sizes
listed in the following TABLE
THE TABLE
Thickness
(a) less than 0.55 mm
less
(b) 0.55 mm to 3 mm
less
(c) greater than 3 mm
less
(d) greater than 13 mm
less
Op. 01.07.1996
Dec. 21.06.1996
Width
than 152 mm
than 24 mm
than 25 mm
than 204 mm
- TC 9607862
7222.19
BARS OR STRIP, stainless steel, flat, hot rolled, cut to length,
in ANY of the sizes listed in the following TABLE
THE TABLE
Thickness
Width
(a) less than 0.55 mm
less than 152 mm
(b) 0.55 mm to 3 mm
less than 24 mm
(c) greater than 3 mm
less than 25 mm
(d) greater than 13 mm
less than 204 mm
Op. 01.07.1996
Dec. 21.06.1996
- TC 9607863
7222.19.00
BARS, flat, stainless steel, hot rolled, annealed and pickled,
thickness NOT less than 3 mm and width NOT greater than 250 mm
Op. 22.09.2005
Dec. 16.12.2005
- TC 0512626
7222.19.00
BARS AND RODS, stainless steel, to specification DIN X42Cr13,
AISI 420 or ASTM 420
Op. 01.07.1996
Dec. 02.07.1996
- TC 9607941
7222.20
BARS, stainless steel, square, having an across the flat dimension
NOT exceeding 50.8 mm
Op. 01.01.1988
Dec. 01.01.1988
- TC 8732313
7222.20
BARS OR RODS, round, stainless steel, dia 17 mm or greater, to
Specification ASTM A 276, Grade UNS S31803, having a chemical
composition by weight of ALL of the following:
(a) carbon
- 0.03% maximum;
(b) manganese
- 2.0% maximum;
(c) phosphorus
- 0.03% maximum;
(d) sulphur
- 0.02% maximum;
(e) silicon
- 1.0% maximum;
(f) chromium
- 21.0% to 23.0% (both inclusive);
(g) nickel
- 4.5% to 6.5% (both inclusive);
(h) molybdenum
- 2.5% to 3.5% (both inclusive);
(i) nitrogen
- 0.03% to 0.20% (both inclusive)
Op. 01.01.1988
Dec. 01.01.1988
- TC 8735458
7222.20
BARS, stainless steel, hexagonal
Op. 28.03.1988
Dec. 08.07.1988
- TC 8804491
7222.20
BARS AND RODS, stainless steel, to Specifications AISI 634,
AISI 630 or similar
Op. 08.01.1990
Dec. 12.03.1990
- TC 9000464
7222.20
BARS AND RODS, stainless steel, to Specification ASTM A564:
UNS S17400
Op. 27.03.1990
Dec. 06.07.1990
- TC 9003536
7222.20
BARS AND RODS, UNS alloy No. S20910, certified to
Specification ASTM A276 or ASTM A314
Op. 22.09.1989
Dec. 29.05.1991
Item 50 applies unless otherwise stated.
- TC 9104154
Tariff
Description
===========================================================================
7222.20
BARS OR RODS, stainless steel, grade UNS S 32750 having the
following chemical composition:
(a) carbon
0.030% maximum;
(b) silicon
0.30%;
(c) manganese
0.40%;
(d) phosphorus
0.030%;
(e) sulphur
0.020%;
(f) chromium
25%;
(g) nickel
10%;
(h) molybdenum
4%;
(i) nitrogen
0.25%
Op. 01.08.1991
Dec. 13.11.1991
- TC 9107068
7222.20
BARS, stainless steel, composition conforming to UNS S31803
Op. 05.08.1992
Dec. 15.10.1992
- TC 9207206
7222.20
BARS, flat, stainless steel, in ANY of the sizes listed in the
following TABLE
THE TABLE
Thickness
Width
(a) less than 0.55 mm
less than 152 mm
(b) 0.55 mm to 3 mm
less than 24 mm
(c) greater than 3 mm
less than 25 mm
(d) greater than 13 mm
less than 204 mm
Op. 13.07.1995
Dec. 13.07.1995
- TC 9506221
7222.20.00
TIES AND/OR RODS, WALL, helical, stainless steel
Op. 08.04.2015
Dec. 06.07.2015
- TC 1513887
7222.20.00
BARS AND/OR RODS, ribbed, cold formed, stainless steel
Op. 05.12.2006
Dec. 02.03.2007
- TC 0619305
7222.20.00
BARS AND RODS, stainless steel, centreless ground, having an
outside diameter exceeding 28.58 mm, to grades 303 OR 304 OR
304L OR 316 OR 316L OR 431
Op. 12.06.2001
Dec. 04.06.2007
- TC 0708234
7222.20.00
BARS AND/OR RODS, STAINLESS STEEL, CENTRELESS GROUND, having an
diameter GREATER than 3.10 mm, but NOT greater than 28.6 mm, to
ANY of the following grades:
(a) 304 and/or 304L;
(b) 316 and/or 316L;
(c) 303;
(d) 630;
(e) 2205;
(f) 431;
(g) 416;
(h) 410;
(i) 420;
(j) 446;
(k) 440;
(l) 310;
(m) 321;
(n) 253ma
Op. 06.07.2005
Dec. 04.06.2007
- TC 0708235
7222.20.00
BARS AND RODS, stainless steel, centreless ground, to specification
AISI Grade 630, having a diameter of NOT less than 12.7 mm and NOT
greater than 200 mm
Op. 23.04.2003
Dec. 04.06.2007
- TC 0708236
7222.20.00
BARS AND/OR RODS, stainless steel, round, having BOTH of the
following:
(a) diameter NOT less than 14.29 mm;
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
(b) compliance with American Society for Testing and Materials
(ASTM), A 582/A 582M-05 and/or A 276-06, Types 303, 304,
304L, 310, 316, 316L, 321, 410, 416, 420, 431, 440A,
440B, 440C or 446
Op. 30.07.2007
Dec. 12.10.2007
- TC 0712182
7222.20.00
RODS, stainless steel, to specification AWS.A5.9. R347, R316L,
R309L or R308L
Op. 20.11.1995
Dec. 01.03.1996
- TC 9512758
7222.20.00
RODS, welding, stainless steel, tungsten inert gas, diameter NOT
exceeding 1.6 mm
Op. 13.10.1997
Dec. 30.12.1997
- TC 9709413
7222.20.00
BARS OR RODS, stainless steel, round, diameter exceeding 28.57 mm to
grades 304 OR 304L OR 316 OR 316L
Op. 05.02.2001
Dec. 23.04.2001
- TC 0101125
7222.20.00
BARS AND RODS, stainless steel, round, with an outside diameter
exceeding 28.75 mm to grades 303 OR 304 OR 304L OR 316 OR 316L OR
431
Op. 05.04.2001
Dec. 15.06.2001
- TC 0102924
7222.20.00
RODS, WELDING, TUNGSTEN INERT GAS, stainless steel, diameter NOT
exceeding 3.2 mm
Op. 19.03.2002
Dec. 14.06.2002
- TC 0202340
7222.30
BARS AND RODS, having a minimum nickel content by weight of 28%
Op. 26.02.1988
Dec. 06.05.1988
- TC 8802076
7222.30
BARS, stainless steel, composition conforming to UNS S31803
Op. 05.08.1992
Dec. 15.10.1992
- TC 9207205
7222.30
BARS, flat, stainless steel, in ANY of the sizes listed in the
following TABLE
THE TABLE
Thickness
Width
(a) less than 0.55 mm
less than 152 mm
(b) 0.55 mm to 3 mm
less than 24 mm
(c) greater than 3 mm
less than 25 mm
(d) greater than 13 mm
less than 204 mm
Op. 13.07.1995
Dec. 13.07.1995
- TC 9508175
7222.30.00
RODS, WELDING
Op. 24.11.2005
7222.30.00
7222.30.00
Dec. 06.02.2006
- TC 0516605
BARS AND/OR RODS, stainless steel, forged
Op. 16.01.2007
Dec. 13.04.2007
- TC 0700893
BARS AND/OR RODS, STAINLESS STEEL
Op. 07.11.2007
Dec. 29.01.2008
- TC 0718915
7222.30.00
BARS AND RODS, stainless steel, to specification DIN X42Cr13,
AISI 420 or ASTM 420
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504088
7222.30.00
BARS, stainless steel, forged to AISI 410
Op. 23.02.1996
Dec. 31.05.1996
- TC 9603432
7222.30.00
BARS, stainless steel, duplex, composition conforming to
UNS S 32550, UNS S 32520 OR UR52N+
Op. 13.05.1998
Dec. 24.07.1998
- TC 9804061
7222.40
ANGLES, stainless steel
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
Op. 06.12.1983
Dec. 06.12.1983
- TC 8342110
7222.40.00
SECTIONS, laser fusion welded, stainless steel, complying with
American Society for Testing and Materials ATSM A1069/A1069M
Op. 22.04.2015
Dec. 20.07.2015
- TC 1515445
7222.40.00
STRUTS, CHANNEL, stainless steel
Op. 08.06.2011
Dec. 22.08.2011
- TC 1118280
7222.40.00
CHANNELS, STAINLESS STEEL, HOT ROLLED, ANNEALED AND PICKLED,
complying with American Society for Testing and Materials A 276
(ASTM A 276), having ALL of the following:
(a) width NOT less than 20 mm;
(b) height NOT less than 10 mm;
(c) thickness NOT less than 2 mm and NOT greater than 30 mm
Op. 13.03.2007
Dec. 08.06.2007
- TC 0703820
7223.00
WIRE, stainless steel, cold rolled and polished, flat section,
thickness NOT exceeding 0.75 mm, OR, if exceeding 0.75 mm having
a width to thickness ratio exceeding 6:1
Op. 01.07.1983
Dec. 01.07.1983
- TC 8334108
7223.00
WELDING WIRE, stainless steel, metal inert gas, dia NOT
exceeding 1.6 mm
Op. 21.02.1984
Dec. 21.02.1984
- TC 8341708
7223.00
WELDING WIRE, stainless steel, tungsten inert gas, dia NOT
exceeding 1.2 mm
Op. 21.02.1984
Dec. 21.02.1984
- TC 8341709
7223.00
WIRE, circular section, NOT exceeding 0.274 mm dia
Op. 14.01.1987
Dec. 21.05.1987
- TC 8732302
7223.00
WIRE, spring temper stainless steel, diameter exceeding 0.46 mm
but NOT exceeding 1.2 mm
Op. 24.03.1992
Dec. 06.08.1992
- TC 9203533
7223.00.00
DETECTABLE WARNING TAPE, polyethylene, printed, incorporating
stainless steel tracer wires
Op. 12.01.2012
Dec. 26.03.2012
- TC 1201485
7223.00.00
WIRE, stainless steel
Op. 12.08.2010
Dec. 08.11.2010
- TC 1037050
7223.00.00
WIRE, STAINLESS STEEL, cold drawn, bright finished, conforming
to Euronorm No 1.4835 (EN 1.4835), having a diameter NOT less
than 0.5 mm and NOT greater than 12 mm
Op. 01.06.2009
Dec. 21.08.2009
- TC 0918435
7223.00.00
WIRE, STAINLESS STEEL, having BOTH of the following:
(a) tensile strength NOT less 700 MPa and NOT greater than
1 000 MPa;
(b) diameter NOT greater than 1 mm
Op. 11.11.2005
Dec. 30.01.2006
- TC 0515954
7223.00.00
WIRE, stainless steel, annealed, conforming to American Iron and
Steel Institute Standard (AISI) Type Number 304, having a
diameter NOT greater than 0.8 mm
Op. 23.06.2006
Dec. 15.09.2006
- TC 0610733
7223.00.00
WIRE, stainless steel, grade EPQ, having a diameter of NOT less
than 1 mm and NOT greater than 5 mm
Op. 20.03.2007
Dec. 08.06.2007
- TC 0704147
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
7223.00.00
WIRE, stainless steel, annealed, having ALL of the following:
(a) diameter NOT less than 1.4 mm;
(b) nickel content NOT less than 34%;
(c) silicon content NOT less than 1.8%;
(d) tensile NOT less than 500 mPa
Op. 23.03.2007
Dec. 15.06.2007
- TC 0704382
7223.00.00
WIRE, STAINLESS STEEL, cold drawn, bright finished, having BOTH
of the following:
(a) diameter NOT less than 0.5 mm and NOT greater than 12 mm;
(b) conforming to ANY of the following AISI grades:
(i) 304;
(ii) 304L;
(iii) 310;
(iv) 316;
(v) 316L
Op. 06.07.2007
Dec. 21.09.2007
- TC 0710734
7223.00.00
WIRE, STAINLESS STEEL, cold drawn, bright finished, having BOTH
of the following:
(a) diameter NOT less than 0.5 mm and NOT greater than 12 mm;
(b) conforming to EITHER of the following AISI grades:
(i) 302;
(ii) 302HQ (302CHQ)
Op. 30.09.2008
Dec. 19.12.2008
- TC 0833357
7223.00.00
WIRE, stainless steel, to AISI specifications 301 or 304, resin or
nickel coated, diameter 0.15 mm to 6.55 mm inclusive
Op. 04.11.1993
Dec. 11.02.1994
- TC 9312742
7223.00.00
WELDING WIRE, stainless steel, gas metal arc welding, diameter NOT
exceeding 1.6 mm
Op. 30.05.1994
Dec. 02.09.1994
- TC 9404912
7223.00.00
WIRE, stainless steel, flat with round edges to specification SAE
30302 or SAE 30304, having a maximum camber of 13 mm over a 2 500 mm
length in the following sizes:
(a) width 2.4 mm to 2.6 mm;
(b) thickness 0.78 mm to 0.82 mm
Op. 04.05.1995
Dec. 11.08.1995
- TC 9505322
7224.90.00
PROFILES, alloy steel, hot extruded
Op. 05.11.2004
Dec. 07.01.2005
- TC 0411812
7225.11
ELECTRICAL STEEL, sheet and strip, cold rolled, grain oriented, as
defined in IEC 401-1, in coil or sheet form, having a core loss
of less than 1.5 W/kg in the long grain direction at flux density
of 1.5 Tesla and frequency 50 Hz as determined by Test Methods to
International Standard IEC 404-2
Op. 01.07.1996
Dec. 12.06.1996
- TC 9604138
7225.11
SHEET, electrical steel, containing from 2.7% to 3.3% (both
inclusive) by weight of silicon
Op. 01.07.1996
Dec. 21.06.1996
- TC 9608819
7225.11.00
SHEETS OR STRIPS, silicon-electrical steel, grain oriented,
cold rolled, in coil OR sheet form, having a width of NOT less
than 600 mm
Op. 13.02.2009
Dec. 08.05.2009
- TC 0905031
7225.19
SHEET, electrical steel, containing from 2.7% to 3.3% (both
inclusive) by weight of silicon
Op. 01.07.1996
Dec. 21.06.1996
- TC 9607816
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
7225.19.00
SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as
described in ANY of the following international standards:
(a) Japanese Industrial Standard C 2552;
(b) American Society for Testing and Materials
Standard A 677-05;
(c) European Standard EN 10106
Op. 23.03.2006
Dec. 16.06.2006
- TC 0605628
7225.40
PLATES AND SHEET, alloy steel, containing more than 11% by weight
of manganese and more than 0.8% carbon
Op. 06.12.1983
Dec. 06.12.1983
- TC 8341588
7225.40
STEEL, to Specification AS 1239-1973, Types D2A, D3A, D4A or D5A
Op. 30.12.1987
Dec. 27.04.1988
- TC 8800908
7225.40.00
PLATES, high alloy steel, quenched AND tempered, having ALL of
the following:
(a) yield strength NOT less than 730 N/mm2;
(b) tensile strength NOT less than 850 N/mm2;
(c) elongation NOT less than 10%;
(d) thickness reduction ratio during plate rolling NOT
less than 3:1;
(e) plate thickness NOT less than 120 mm;
(f) plate length NOT less than 7 200 mm;
(g) plate mass NOT less than 18 000 kg
Op. 10.02.2014
Dec. 08.05.2014
- TC 1405583
7225.40.00
PLATES OR SHEETS, high alloy steel, grain refined, quenched and
tempered, having ALL of the following:
(a) hardness NOT less than 570 HBW and NOT greater than 640 HBW;
(b) yield strength NOT less than 1 300 N/mm2;
(c) tensile strength NOT less than 2 000 N/mm2;
(d) elongation NOT less than 7%
Op. 18.11.2009
Dec. 19.03.2010
- TC 0943669
7225.40.00
PLATES AND SHEET, high speed steel, but NOT including those that
have been hollow ground OR those that have centre holes OR pin
holes
Op. 01.01.2007
Dec. 08.11.2006
- TC 0614205
7225.40.00
PLATE OR SHEET, nickel alloy steel, complying with American
Society for Testing and Materials (ASTM) designation A553
Op. 09.05.2008
Dec. 08.08.2008
- TC 0807304
7225.40.00
PLATES, SHEETS AND FLATS, high alloy steel, to specification
DIN X45NiCrMo4
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504052
7225.40.00
SHEETS, PLATES AND FLATS, high alloy steel, to specification DIN
90MnCrV8
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504075
7225.40.00
PLATES, SHEETS AND FLATS, high alloy steel, to specification
DIN X155CrVMo12 1, BS BD2 or AISI D2
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504095
7225.40.00
PLATE, SHEET AND BAR, high alloy steel, specification DIN
X40CrMoV51, BS BH13 or AISI H13
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504104
7225.40.00
PLATES, SHEETS AND FLATS, high alloy steel, to specification
DIN 40CrMnNiMo8 6 4, hardened and tempered within the range of
980 N - 1 080 N per square millimetre (both inclusive)
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
Op. 29.06.1995
Dec. 06.10.1995
- TC 9508565
7225.40.00
PLATES OR SHEETS OR FLATS, high alloy steel, to specifications
DIN 40CrMnMoS8 6, hardened and tempered
Op. 14.11.2002
Dec. 31.01.2003
- TC 0210776
7225.50.00
STEEL, flat rolled, alloy, cold rolled, in coils, having ALL
of the following:
(a) yield strength NOT less than 340 MPa and NOT greater than
900 MPa;
(b) tensile strength NOT less than 590 MPa;
(c) total elongation NOT less than 8%;
(d) in ANY of the following sizes:
(i) thickness 1.20 mm and width 820 mm;
(ii) thickness 1.20 mm and width 1 180 mm;
(iii) thickness 1.20 mm and width 1 250 mm
For the purposes of this Order, tolerances allowable for
specification (d) are:
(a) thickness +/- 10%
(b) width +/- 1%
Op. 22.05.2013
7225.50.00
Dec. 12.08.2013
- TC 1316843
STEEL, flat rolled, alloy, cold rolled, in coils, having ALL of
the following:
(a) yield strength NOT greater than 570 MPa;
(b) tensile strength NOT less than 690 MPa;
(c) elongation NOT less than 20%;
(d) in ANY of the following sizes:
(i) thickness 1.15 mm and width 600 mm;
(ii) thickness 1.15 mm and width 720 mm;
(iii) thickness 1.20 mm and width 1 080 mm;
(iv) thickness 1.45 mm and width 1 340 mm;
(v) thickness 1.55 mm and width 678 mm;
(vi) thickness 1.60 mm and width 1 012 mm
For the purposes of this Order, tolerances allowable for
specification (d) are:
(a) thickness +/- 10%
(b) width +/- 1%
Op. 03.04.2013
7225.50.00
Dec. 24.06.2013
- TC 1311482
STEEL, flat rolled, alloy, cold rolled, having ALL of the
following:
(a) yield strength NOT less than 340 MPa and NOT greater than
440 MPa;
(b) tensile strength NOT less than 590 MPa;
(c) total elongation NOT less than 22%;
(d) thickness 1.20 mm and width 900 mm
For the purposes of this Order, tolerances allowable for
specification (d) are:
(a) thickness +/- 10%
(b) width +/- 1%
Op. 13.03.2013
7225.50.00
Dec. 03.06.2013
- TC 1309153
SHEET OR PLATE, alloy steel, cold rolled, to Japanese Industrial
Standard G 3125 (JIS G 3125), type SPA-C, thickness NOT greater
than 2.3 mm
Op. 25.05.2009
Dec. 14.08.2009
- TC 0917506
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
7225.91.00
STEEL, flat rolled, alloy, electrolytically plated OR zinc
coated, in coils, having ALL of the following:
(a) yield strength NOT less than 110 MPa and NOT greater than
160 MPa;
(b) tensile strength NOT less than 260 MPa;
(c) elongation NOT less than 42%;
(d) coating mass NOT less than 36 g/m2 on each side;
(e) thickness 0.70 mm and width 1 480 mm
For the purposes of this Order, tolerances allowable for
specification (e) are:
(a) thickness +/- 10%
(b) width +/- 1%
Op. 21.08.2013
Dec. 18.11.2013
- TC 1328532
7225.92.00
STEEL, flat rolled, alloy, hot dipped zinc coated, in coils,
having ALL of the following:
(a) yield strength NOT less than 340 MPa and NOT greater than
700 MPa;
(b) tensile strength NOT less than 590 MPa;
(c) elongation NOT less than 10%;
(d) coating mass NOT less than 60 g/m2 and NOT greater than
120 g/m2 on each side;
(e) in ANY of the following sizes:
(i) thickness 1.20 mm and width 615 mm;
(ii) thickness 1.20 mm and width 623 mm;
(iii) thickness 1.20 mm and width 1 115 mm;
(iv) thickness 1.20 mm and width 1 240 mm;
(v) thickness 1.20 mm and width 1 256 mm;
(vi) thickness 1.40 mm and width 900 mm;
(vii) thickness 1.80 mm and width 970 mm;
(viii) thickness 2.00 mm and width 889 mm;
(ix) thickness 2.00 mm and width 970 mm;
(x) thickness 2.00 mm and width 992 mm
For the purposes of this Order, tolerances allowable for
specification (e) are:
(a) thickness +/- 10%
(b) width +/- 1%
Op. 22.05.2013
7225.92.00
Dec. 12.08.2013
- TC 1316844
STEEL, flat rolled, alloy, hot dipped zinc coated, having ALL of
the following:
(a) yield strength NOT less than 700 MPa and NOT greater than
900 MPa;
(b) tensile strength NOT less than 980 MPa and NOT greater
than 1 200 MPa;
(c) total elongation NOT less than 10%;
(d) total coating mass NOT less than 60 g/m2 and NOT greater
than 90 g/m2 on each side;
(e) thickness 0.90 mm and width 1 020 mm
For the purposes of this Order, tolerances allowable for
specification (e) are:
(a) thickness +/- 10%
(b) width +/- 1%
Op. 13.03.2013
7225.99.00
Dec. 03.06.2013
- TC 1309154
PLATES, ATMOSPHERIC PRESSURE LIQUID NATURAL GAS STORAGE TANK,
nickel alloy steel, complying with American Society Testing and
Materials standard A553/A553M - 10 (ASTM A553/A553M - 10),
having ALL of the following:
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
(a) bevelled edges NOT less than 30 degrees and NOT greater
than 45 degrees;
(b) plate thickness NOT less than 9.53 mm and NOT greater than
16.6 mm;
(c) roll radius NOT less than 30 m and NOT greater than 31 m
Op. 17.09.2013
Dec. 09.12.2013
- TC 1331764
7225.99.00
STEEL, flat rolled, alloy, in coils, having ALL of the following:
(a) hot dipped coating having BOTH of the following:
(i) NOT less than 85% aluminium;
(ii) NOT less than 5% silicon and NOT greater than 11%
silicon;
(b) coating mass NOT less than 60 g/m2 and NOT greater than 100
g/m2 on each side;
(c) yield strength NOT less than 300 MPa;
(d) tensile strength NOT less than 500 MPa;
(e) elongation NOT less than 17%;
(f) in ANY of the following sizes:
(i) thickness 1.00 mm and width 938 mm;
(ii) thickness 1.20 mm and width 1 202 mm;
(iii) thickness 1.40 mm and width 918 mm;
(iv) thickness 1.40 mm and width 995 mm;
(v) thickness 2.00 mm and width 1 325 mm
For the purposes of this order, tolerances allowable for
specification (f) are:
(a) thickness +/- 10%;
(b) width +/- 1%
Op. 22.05.2013
7225.99.00
Dec. 12.08.2013
- TC 1316845
STEEL, flat rolled, alloy, having ALL of the following:
(a) hot dipped coating aluminium content NOT less than 85%;
(b) hot dipped coating silicon content NOT less than 5%
and NOT greater than 11%;
(b) total coating mass NOT less than 60 g/m2 and NOT greater
than 100 g/m2 on each side;
(c) yield strength NOT less than 300 MPa;
(d) tensile strength NOT less than 500 MPa;
(e) total elongation NOT less than 17%;
(f) in BOTH of the following sizes:
(i) thickness 1.00 mm and width 938 mm;
(ii) thickness 1.40 mm and width 918 mm
Tolerances allowable for specification (f) are:
(a) thickness +/- 10%
(b) width +/- 1%
Op. 13.03.2013
7225.99.00
Dec. 03.06.2013
- TC 1309157
SHEETS, alloy steel, complying with American Society of Testing
and Materials Standard ASTM A 463/A 463M-05 with Steel Sheet
Designations CS, FS, DDS OR EDDS AND Coating Designations T1-25
OR T1-40, whether OR not in coils, having ALL of the following:
(a) width of 630 mm, 685 mm, 699 mm, 780 mm, 790 mm, 810 mm,
900 mm, 914 mm, 930 mm, 990 mm, 1 000 mm, 1 025 mm,
1 030 mm, 1 035 mm, 1 066 mm, 1 078 mm, 1 084 mm,
1 100 mm, 1 120 mm, 1 126 mm, 1 134 mm, 1 146 mm,
1 160 mm, 1 165 mm 1 170 mm, 1 195 mm, 1 200 mm,
1 210 mm, 1 219 mm, 1 220 mm, 1 246 mm OR 1 250 mm,
each having a width tolerance of + OR - 2 mm;
(b) thickness of 0.55 mm, 0.60 mm, 0.72 mm, 0.75 mm, 0.80 mm,
0.90 mm, 0.96 mm, 1.00 mm, 1.15 mm, 1.20 mm, 1.50 mm,
1.55 mm, 1.60 mm, 1.90 mm OR 2.00 mm, each having a
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
thickness tolerance of + OR - 0.2 mm;
(c) aluminium AND silicon coating having BOTH of the following:
(i) aluminium content NOT less that 88%;
(ii) weight NOT less than 20 gsm and NOT greater
than 90 gsm
Op. 01.06.2012
Dec. 20.08.2012
- TC 1218779
7226.11
ELECTRICAL STEEL, sheet and strip, cold rolled, grain oriented, as
defined in IEC 401-1, in coil or sheet form, having a core loss
of less than 1.5 W/kg in the long grain direction at flux density
of 1.5 Tesla and frequency 50 Hz as determined by test methods to
International Standard IEC 404-2
Op. 01.07.1996
Dec. 12.06.1996
- TC 9605782
7226.11
HOOP AND STRIP, electrical steel, having a silicon content of
2.7% to 3.3% (both inclusive), of rectangular section, of a
thickness NOT exceeding 6 mm, of a width NOT exceeding 500 mm
and of such dimension that the thickness does NOT exceed one
tenth of the width
Op. 01.07.1996
Dec. 24.06.1996
- TC 9607901
7226.11
SHEET, electrical steel, containing from 2.7% to 3.3% (both
inclusive) by weight of silicon
Op. 01.07.1996
Dec. 03.07.1996
- TC 9608435
7226.11.00
SHEETS OR STRIPS, silicon-electrical steel, grain oriented,
cold rolled, in coil OR sheet form, having a width less than
600 mm
Op. 13.02.2009
Dec. 08.10.2009
- TC 0918076
7226.19
SHEET, electrical steel, containing from 2.7% to 3.3% (both
inclusive) by weight of silicon
Op. 01.07.1996
Dec. 03.07.1996
- TC 9608436
7226.19.00
SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as
described in ANY of the following international standards:
(a) Japanese Industrial Standard C 2552;
(b) American Society for Testing and Materials
Standard A 677-05;
(c) European Standard EN 10106
Op. 23.03.2006
Dec. 16.06.2006
- TC 0605629
7226.19.00
HOOP, strip or sheet, electrical steel, having a minimum silicon
content by weight of 2.3%
Op. 01.07.1996
Dec. 21.06.1996
- TC 9607865
7226.91.00
BARS, flat, alloy steel, NOT in a hardened and tempered condition,
having ALL of the following:
(a) width exceeding 140 mm but NOT exceeding 460 mm;
(b) thickness exceeding 50 mm but NOT exceeding 200 mm;
(c) length NOT exceeding 12 m
Op. 15.11.1993
Dec. 25.03.1994
- TC 9313230
7226.91.00
BARS, flat, having a thickness NOT exceeding 200 mm and a width NOT
exceeding 520 mm, to ANY of the following specifications:
(a) AISI-01;
(b) BS 4659: 1989, in ANY of the following grades:
(i) BA 6;
(ii) BD 2;
(iii) BD 2A;
(iv) BD 6;
(v) BO 1;
(c) DIN 1.2101
Op. 24.06.1994
Dec. 14.10.1994
- TC 9405333
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
7226.91.00
PLATES, SHEETS AND FLATS, high alloy steel, to specification DIN
X155CrVMo12 1, BS BD2 or AISI D2
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504070
7226.92
HOOP AND STRIP, hardened and tempered, of rectangular section,
of a thickness NOT exceeding 6 mm, of a width NOT exceeding
500 mm and of such dimension that the thickness does NOT exceed
one tenth of the width
Op. 01.01.1988
Dec. 01.01.1988
- TC 8801182
7226.92.00
STEEL, flat rolled, alloy, cold rolled, in coils, having ALL of
the following:
(a) yield strength NOT greater than 570 MPa;
(b) tensile strength NOT less than 690 MPa;
(c) elongation NOT less than 20%;
(d) thickness 1.60 mm and width 167 mm
For the purposes of this Order, tolerances allowable for
specification (d) are:
(a) thickness +/- 10%
(b) width +/- 1%
Op. 03.04.2013
7226.92.00
Dec. 24.06.2013
- TC 1311481
STEEL, flat rolled, alloy steel, cold rolled, complying
with Japanese Industrial Standard G3135 (JIS G3135), grade
SPFC980Y, having ALL of the following:
(a) yield strength NOT less than 580 MPa and NOT greater than
920 MPa;
(b) tensile strength NOT less than 980 MPa;
(c) total elongation NOT less than 11% and NOT greater than
22%;
(d) thickness 1.40 mm and width 435 mm
For the purposes of this Order, tolerances allowable for
specification (d) are:
(a) thickness +/- 10%
(b) width +/- 1%
Op. 28.12.2012
7226.92.00
Dec. 18.03.2013
- TC 1349347
STEEL STRIP, cold rolled, in coil form, having ALL of the
following:
(a) chemical composition by percentage of weight in
accordance with EITHER of the compositions listed in
THE TABLE;
(b) dimensions, being ANY of the following width and
thickness combinations:
(i) 26 mm width (25.91/26.42 mm) x 4 mm thickness
(3.90/4.12 mm);
(ii) 26 mm width (25.91/26.42 mm) x 4.5 mm thickness
(4.49/4.71 mm);
(iii) 39 mm width (38.61/39.12 mm) x 4 mm thickness
(3.56/3.80 mm);
(iv) 39 mm width (38.61/39.12 mm) x 5 mm thickness
(4.83/5.09 mm),
(c) camber tolerance in accordance with British Standard
1449 (BS1449) Part 1, Table 30
THE TABLE
COMPOSITION 1
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
CARBON (C) NOT less than 0.37 and NOT greater than 0.44;
MANGANESE (Mn) NOT less than 0.70 and NOT greater than 1.00;
SILICON (Si) NOT less than 0.17 and NOT greater than 0.37;
SULPHUR (S) NOT greater than 0.035;
PHOSPHOROUS (P) NOT greater than 0.035;
CHROMIUM (Cr) NOT greater than 0.25;
NICKEL (Ni) NOT less than 0.30;
COPPER (Cu) NOT greater than 0.25
COMPOSITION 2
CARBON (C) NOT less than 0.37 and NOT greater than 0.44;
MANGANESE (Mn) NOT less than 0.50 and NOT greater than 0.80;
SILICON (Si) NOT less than 0.17 and NOT greater than 0.37;
SULPHUR (S) NOT greater than 0.035;
PHOSPHOROUS (P) NOT greater than 0.035;
CHROMIUM (Cr) NOT less than 0.80 and NOT greater than 1.10;
NICKEL (Ni) NOT greater than 0.30;
COPPER (Cu) NOT greater than 0.30
Op. 01.03.2010
Dec. 30.04.2010
- TC 1010373
7226.99
HOOP AND STRIP, hardened and tempered, of rectangular section,
of a thickness NOT exceeding 6 mm, of a width NOT exceeding
500 mm and of such dimension that the thickness does NOT exceed
one tenth of the width
Op. 01.01.1988
Dec. 01.01.1988
- TC 8801183
7226.99.00
STEEL, flat rolled, alloy, having ALL of the following:
(a) hot dipped coating of NOT less than 85% aluminium;
(b) hot dipped coating silicon content NOT less than 5% and
NOT greater than 11%;
(c) total coating mass NOT less than 50 g/m2 and NOT greater
than 110 g/m2 on each side;
(d) yield strength NOT less than 300 MPa;
(e) tensile strength NOT less than 500 MPa;
(f) total elongation NOT less than 12%;
(g) in BOTH of the following sizes:
(i) thickness 1.00 mm and width 232 mm;
(ii) thickness 1.40 mm and width 454 mm
For the purposes of this Order, tolerances allowable for
specification (g) are:
(a) thickness +/- 10%
(b) width +/- 1%
Op. 05.09.2013
7226.99.00
Dec. 02.12.2013
- TC 1330258
STEEL PLATE, having BOTH of the following:
(a) nickel content greater than 34%;
(b) width less than 600 mm
Op. 18.08.2008
Dec. 07.11.2008
- TC 0826920
7226.99.00
BARS, flat, to specification AISI-01, having a thickness NOT
exceeding 100 mm or a width NOT exceeding 300 mm
Op. 11.03.1993
Dec. 28.06.1993
- TC 9304094
7226.99.00
FLATS, high alloy, to specification DIN 100MnCrW4, BS B01 or AISI01
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504060
7226.99.00
STRIP, STEEL, in coils, hardened, sharpened on one or both edges,
thickness 1.5 mm to 4 mm, width 19 mm to 50 mm
Op. 04.06.1998
Dec. 14.08.1998
- TC 9804815
7227.90
WIRE RODS to specification SAE 52100
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
Op. 24.03.1992
Dec. 13.08.1992
- TC 9203978
7227.90.10
COILS, alloy steel, hot rolled, complying with European Standard
EN 10089:2002, having a thickness NOT less than 18 mm and NOT
greater than 24 mm
Op. 04.02.2011
Dec. 02.05.2011
- TC 1105008
7228.10
BARS OR RODS, high speed steel, but NOT including ANY of the
following:
(a) round bars OR rods having a dia of 1.60 mm or greater
but NOT exceeding 14.00 mm;
(b) hardened bars OR rods, of rectangular OR square
cross-section
For the purposes of TC 8734392 "high speed steel" means that
it contains:
(a) NOT less than 0.60% carbon; and
(b)
(i) chromium; or
(ii) vanadium; or
(iii) cobalt; and
(c)
(i) molybdenum and tungsten, in such percentages by
weight that the sum of the number equal to the
percentage of tungsten and the number equal to
twice the percentage of molybdenum is NOT less
than 13.5%; or
(ii) NOT less than 7% by weight of molybdenum; or
(iii) NOT less than 14% by weight of tungsten
Op. 21.08.1986
Dec. 20.08.1987
- TC 8734392
7228.10.00
BARS OR RODS, high speed steel
Op. 14.05.2013
Dec. 05.08.2013
7228.20.29
RODS, WELDING
Op. 20.12.2011
Dec. 22.05.2012
- TC 1315927
- TC 1142159
7228.20.90
BARS, alloy steel, hot rolled, having a diameter NOT less than
21 mm and NOT greater than 24 mm
Op. 15.07.2008
Dec. 10.10.2008
- TC 0818903
7228.30
RODS, gas welding, cast iron
Op. 13.03.1984
Dec. 13.03.1984
- TC 8342156
7228.30
BARS, flat, alloy steel, having ALL of the following:
(a) width less than 150.0 mm;
(b) thickness exceeding 3.25 mm but less than 50.00 mm;
(c) length NOT exceeding 10.0 m
Op. 13.07.1994
Dec. 13.07.1994
- TC 8736255
7228.30.10
BARS OR RODS, high alloy steel, conforming to European
Standard grade EN 26, NOT heat treated OR further processed
other than
annealing
Op. 26.04.2012
Dec. 09.07.2012
- TC 1213440
7228.30.10
THREADED BARS, high alloy steel, hot rolled, having ALL of the
following:
(a) yield strength NOT less than 500 N/mm2;
(b) cerium content NOT less than 0.1% and NOT greater
than 0.5%;
(c) threaded ribs
Op. 22.03.2012
Dec. 18.06.2012
- TC 1209607
7228.30.10
THREADED BARS, high alloy steel, hot rolled, having ALL of the
following:
(a) working temperature down to minus 170 degrees Celsius;
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
(b) yield strength NOT less than 500 N/mm2;
(c) threaded ribs
Op. 22.03.2012
Dec. 18.06.2012
- TC 1209606
7228.30.10
STEEL BARS, hexagonal, high alloy steel, across the flat NOT
less than 33 mm and NOT greater than 65 mm
Op. 20.07.2011
Dec. 19.10.2011
- TC 1124118
7228.30.10
BARS, round, high alloy steel, hot rolled, grade 38B3, having
BOTH of the following:
(a) diameter NOT less than 25 mm and NOT greater than 65 mm;
(b) length NOT greater than 6 m
Op. 14.01.2010
Dec. 07.04.2010
- TC 1002629
7228.30.10
BARS, HOT ROLLED, HIGH ALLOY, having a diameter NOT less than
100 mm
Op. 02.07.2007
Dec. 14.09.2007
- TC 0705688
7228.30.10
BARS, alloy steel, hot rolled, having a diameter NOT less than
21 mm and NOT greater than 24 mm
Op. 15.07.2008
Dec. 10.10.2008
- TC 0818895
7228.30.10
BARS OR RODS, high alloy steel, conforming to International
Material No. 1.6582, Specification 34CrNiMo6
Op. 21.11.2008
Dec. 27.02.2009
- TC 0840864
7228.30.10
BARS OR RODS, high alloy steel, grades 8620 or 8620H or SNCM220
or SNCM220H, having a chemical composition by weight of ALL of
the following:
(a) Carbon
- 0.17% to 0.23% (both inclusive);
(b) Silicon
- 0.10% to 0.35% (both inclusive);
(c) Manganese - 0.60% to 0.95% (both inclusive);
(d) Chromium
- 0.35% to 0.65% (both inclusive);
(e) Molybdenum - 0.15% to 0.30% (both inclusive);
(f) Nickel
- 0.35% to 0.75% (both inclusive)
Op. 05.12.2008
Dec. 27.02.2009
- TC 0842882
7228.30.10
BARS, alloy steel, round, diameter NOT exceeding 500 mm, to ANY
of the following specifications:
(a) AISI-01;
(b) AISI-B.01
(c) AISI-B.D2
(d) AISI-B.D3
(e) AISI-B.A6
(f) AISI-D.K4
Op. 16.06.1993
Dec. 01.10.1993
- TC 9304547
7228.30.10
BARS, round, alloy steel, conforming to BS1506 (1990) Grade 681-820
Op. 25.07.1994
Dec. 04.11.1994
- TC 9406340
7228.30.10
HOT ROLLED ROUND STEEL BAR, hardened and tempered, high tensile, to
material specification AISI 4140 H or 4340 H and size tolerance
DIN 1013, diameter 90mm to 149mm (both inclusive)
Op. 01.02.1995
Dec. 13.06.1995
- TC 9501328
7228.30.10
BARS AND RODS, high alloy steel, to specification DIN 100Cr6
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504021
7228.30.10
BARS AND RODS, high alloy steel, to specification DIN 14NiCr14, in
either of the following sizes:
(a) less than 22 mm diameter;
(b) greater than 82 mm diameter
Op. 14.02.1995
Dec. 05.06.1995
- TC 9504027
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
7228.30.10
BARS AND RODS, high alloy steel, to specification DIN 34CrAlNi7,
hardened and tempered within the range of 800-1050 N per sq. mm
(both inclusive)
Op. 14.02.1995
Dec. 07.06.1995
- TC 9504073
7228.30.10
BARS AND RODS, high alloy steel, having a chemical composition by
weight of ALL of the following:
(a) carbon
0.53%;
(b) silicon
0.25%;
(c) manganese
0.45%;
(d) chromium
1.00%;
(e) molybdenum 0.20%;
(f) nickel
3.10%
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504083
7228.30.10
BARS AND RODS, high alloy steel to specification DIN X210Cr12
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504101
7228.30.10
BARS AND RODS, high alloy, to specification DIN X155CrVMo12 1,
BS BD2 or AISI D2
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504102
7228.30.10
BARS AND RODS, high alloy steel, having a chemical composition by
weight of ALL of the following:
(a) carbon
- 1.10%;
(b) silicon
- 0.90%;
(c) manganese - 0.40%;
(d) chromium
- 8.30%;
(e) molybdenum - 2.10%;
(f) vanadium
- 0.50%;
(g) + aluminium;
(h) + niobium
Op. 04.04.1996
Dec. 05.07.1996
- TC 9605301
7228.30.10
BARS AND RODS, high alloy steel, to BS standard EN39B
Op. 04.04.1996
Dec. 05.07.1996
- TC 9605307
7228.30.10
BARS AND RODS, high alloy steel, to specification DIN 1.3401
Op. 04.04.1996
Dec. 05.07.1996
- TC 9605324
7228.30.10
BARS AND RODS, high alloy steel, to specification DIN 1.6587
Op. 04.04.1996
Dec. 05.07.1996
- TC 9605333
7228.30.10
BARS OR RODS, high alloy steel, to DIN specification 1.2436,
(X210CrW12)
Op. 10.04.1996
Dec. 12.07.1996
- TC 9605601
7228.30.10
BARS AND RODS, high alloy steel, to specification
DIN 40CrMnNiMo8 6 4
Op. 10.04.1996
Dec. 12.07.1996
- TC 9605609
7228.30.10
BARS OR RODS, high alloy steel, to standard SAE 4340
Op. 10.04.1996
Dec. 08.08.1996
- TC 9605613
7228.30.10
BARS AND RODS, round, hot rolled, high alloy steel, complying
with AMS (Aerospace Material Specification) 6418F
Op. 03.04.2002
Dec. 21.06.2002
- TC 0202715
7228.30.10
BARS OR RODS, high alloy steel, to specifications DIN X40CrMoV51,
BS BH13 OR AISI H13
Op. 14.11.2002
Dec. 31.01.2003
- TC 0210771
7228.30.10
BARS OR RODS, high alloy steel, to specifications DIN 40CrMnMoS8 6,
hardened and tempered
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
Op. 14.11.2002
Dec. 31.01.2003
- TC 0210773
7228.30.90
BARS OR RODS, high alloy steel, annealed AND peeled, complying
with British Standard 970-3:1991 (BS 970-3:1991) Grade 655M13,
having ALL of the following:
(a) sulphur AND phosphorous content NOT greater than 0.01%;
(b) molybdenum content NOT greater than 0.20%;
(c) grain size NOT less than 6.0, complying to American
Society for Testing and Materials standard E112-13
(ASTM E112-13);
(d) etch testing complying with American Society for Testing
and Materials standard E381-01 (ASTM E381-01), being
evaluated for S, R and C ratings to plate 1, having
ratings NOT greater than S1, R1, C1;
(e) tested to German Institute for Standardisation
50 602 (DIN 50 602) method K4, with the maximum overall
total index of 20 according to table 7 of the standard
Op. 16.09.2014
Dec. 11.02.2015
- TC 1432916
7228.30.90
REINFORCING BARS, CRYOGENIC, LIQUID NATURAL GAS STORAGE TANK,
having ALL of the following:
(a) un-notched bar uniform elongation at maximum force
("Agt") NOT less than 3% at cryogenic temperature minus
168 degrees Celsius;
(b) un-notched bar yield strength NOT less 575 MPa;
(c) transverse rib surface geometry
Op. 05.06.2013
Dec. 26.08.2013
- TC 1318642
7228.30.90
BARS, GROUSER, hot rolled alloy steel
Op. 05.10.2007
Dec. 14.12.2007
- TC 0716888
7228.30.90
BARS OR RODS, steel, grades 15B34M or SMNB3H-1,
having a chemical composition by weight of ALL of the following:
(a) Carbon
0.32% to 0.36%
(both inclusive);
(b) Silicon
0.15% to 0.35%
(both inclusive);
(c) Manganese 1.00% to 1.40%
(both inclusive);
(d) Chromium
0.15% to 0.045% (both inclusive);
(e) Aluminium - 0.015% to 0.045% (both inclusive);
(f) Boron
- 0.0005% to 0.0035% (both inclusive)
Op. 05.12.2008
Dec. 27.02.2009
- TC 0842884
7228.30.90
BARS AND RODS, low alloy, to specification DIN 62SiMnCr4
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504047
7228.40.10
BARS, round, forged, alloy steel, having a diameter NOT less
than 200 mm
Op. 29.01.2007
Dec. 20.04.2007
- TC 0701555
7228.40.10
BARS, alloy steel, round, diameter NOT exceeding 500 mm, to ANY of
the following Specifications:
(a) AISI-01;
(b) AISI-B.01;
(c) AISI-B.D2;
(d) AISI-B.D3;
(e) AISI-B.A6;
(f) AISI-D.K4
Op. 16.06.1993
Dec. 01.10.1993
- TC 9304548
7228.40.10
BARS, FLAT, alloy steel, having ALL of the following:
(a) width NOT exceeding 460 mm;
(b) thickness NOT exceeding 100 mm;
(c) length NOT exceeding 10 m
Op. 11.03.1993
Dec. 18.06.1993
- TC 9308735
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
7228.40.10
BARS OR RODS, high alloy steel, to specification DIN 40CrMnNiMo8 6 4
Op. 14.11.2002
Dec. 31.01.2003
- TC 0210785
7228.50
BARS, flat, alloy steel, having ALL of the following:
(a) width less than 150.0 mm;
(b) thickness exceeding 3.25 mm but less than 50.00 mm;
(c) length NOT exceeding 10.0 m
Op. 13.07.1994
Dec. 13.07.1994
- TC 8736257
7228.50.00
BARS AND RODS, high alloy steel, complying with European
Standard EN 10085:2001, Designation: Steel name 41CrAlMo7-10 OR
Steel number 1.8509
Op. 14.11.2013
Dec. 14.02.2014
- TC 1338756
7228.50.00
BARS, alloy steel, round, diameter NOT exceeding 500 mm, to ANY of
the following specifications:
(a) AISI-01;
(b) AISI-B.01;
(c) AISI-B.D2;
(d) AISI-B.D3;
(e) AISI-B.A6;
(f) AISI-D.K4
Op. 01.07.1995
Dec. 03.07.1995
- TC 9505822
7228.60
BARS, flat, alloy steel, having ALL of the following:
(a) width less than 150.0 mm;
(b) thickness exceeding 3.25 mm but less than 50.00 mm;
(c) length NOT exceeding 10.0 m
Op. 13.07.1994
Dec. 13.07.1994
- TC 8736258
7228.60.10
BARS OR RODS, high alloy steel, annealed, complying with
American Iron and Steel Institute specification 8645 (AISI 8645)
Op. 30.07.2008
Dec. 24.10.2008
- TC 0823945
7228.60.10
BARS AND RODS, high alloy steel, to specification DIN X32CrMoV333 or
BS BH10A
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504067
7228.60.10
BARS AND RODS, high alloy, to specification DIN 60WCrV7
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504081
7228.60.10
BARS AND RODS, high alloy, to specification DIN X155CrVMo12 1,
BS BD2 or AISI D2
Op. 14.02.1995
Dec. 31.05.1995
- TC 9504100
7228.60.10
BARS AND RODS, high alloy steel, having a chemical composition by
weight of ALL of the following:
(a) carbon
- 1.10%;
(b) silicon
- 0.90%;
(c) manganese - 0.40%;
(d) chromium
- 8.30%;
(e) molybdenum - 2.10%;
(f) vanadium
- 0.50%;
(g) + aluminium;
(h) + niobium
Op. 04.04.1996
Dec. 05.07.1996
- TC 9605302
7228.60.10
BARS OR RODS, high alloy steel, to specification
DIN 40CrMnNiMo8 6 4
Op. 10.04.1996
Dec. 12.07.1996
7228.60.10
- TC 9605608
BARS OR RODS, high alloy steel, to specifications DIN X40CrMoV51,
BS BH13 OR AISI H13
Op. 14.11.2002
Dec. 31.01.2003
- TC 0210770
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
7228.60.10
BARS OR RODS, high alloy steel, to specifications DIN 40CrMnMoS8 6,
hardened and tempered
Op. 14.11.2002
Dec. 31.01.2003
- TC 0210772
7228.60.90
RODS, WELDING
Op. 24.11.2005
Dec. 06.02.2006
- TC 0516612
STEEL, silver
Op. 29.04.1993
Dec. 09.08.1993
- TC 9305478
7228.60.90
7228.70.00
PILLAR BLANKS, being pre-cut shapes OR sections of flat rolled
alloy steel, having ALL of the following:
(a) hot dipped coating NOT less than 85% aluminium and NOT
less than 5% silicon and NOT greater than 11% silicon;
(b) yield strength NOT less than 300 MPa;
(c) tensile strength NOT less than 500 MPa;
(d) total elongation NOT less than 17%;
(e) total coating mass on each side NOT less than 60 g/m2 and
NOT greater than 100 g/m2;
(f) chemistry specification of base steel being:
(i) carbon NOT less than 0.19% and NOT greater than
0.27%;
(ii) manganese NOT less than 1.00% and NOT greater than
1.50%;
(iii) aluminium NOT less than 0.010%;
(iv) silicon NOT greater than 0.50%;
(v) phosphorous NOT greater than 0.030%;
(vi) sulphur NOT greater than 0.050%;
(vii) chromium NOT greater than 0.35%;
(viii) titanium NOT less than 0.020% and NOT greater
than 0.055%;
(ix) nitrogen NOT greater than 0.010%;
(x) boron NOT less than 0.0005% and NOT greater than
0.004%
Op. 25.03.2013
Dec. 17.06.2013
- TC 1310468
7228.80.00
DRILL BARS AND RODS, hollow, external cross-section dimension
exceeding 15 mm but NOT exceeding 52 mm, threaded or tapered
Op. 25.09.1996
Dec. 02.12.1996
- TC 9611038
7228.80.00
STEEL, ROCK DRILL, hollow
Op. 31.12.1997
7229.20.00
Dec. 13.03.1998
- TC 9800003
WIRE, WELDING, silico-manganese steel
Op. 06.04.2011
Dec. 27.06.2011
- TC 1111594
7229.90
WIRE, piano, bright, tinned or polished, but NOT including bright
wire having a dia of 0.234 mm or greater but NOT exceeding
3.658 mm
Op. 28.02.1984
Dec. 28.02.1984
- TC 8341668
7229.90
WIRE, silicon chrome spring steel
Op. 28.02.1984
Dec. 28.02.1984
- TC 8341671
7229.90
WIRE, fastener, soft drawn, to Specification AISI 4037
Op. 28.02.1984
Dec. 28.02.1984
- TC 8341672
7229.90
WELDING WIRE, solid metal inert gas, to ANY of the following
British Standards or their equivalents:
(a) BS2901/Part 1 - A30;
(b) BS2901/Part 1 - A31;
(c) BS2901/Part 1 - A32;
(d) BS2901/Part 1 - A33;
Item 50 applies unless otherwise stated.
Tariff
Description
===========================================================================
(e) BS2901/Part 1 - A34
Op. 04.09.1984
Dec. 04.09.1984
- TC 8432144
7229.90.90
WIRE, FASTENER, cold heading quality alloy steels, diameter NOT
less than 12 mm, in ANY of the following grades:
(a) 10B21;
(b) 10B40;
(c) 51B37;
(d) 51B40
Op. 17.02.2009
Dec. 15.05.2009
- TC 0905289
7229.90.90
WIRE, WELDING
Op. 01.01.2007
Item 50 applies unless otherwise stated.
Dec. 08.11.2006
- TC 0614203