Nautical
Seating & Bedding
SLAT BASES
Comfortis® slat bases are the primary on-board sleeping systems of
choice for the true sleep connoisseur. Made of bent and laminated
beechwood, they are the ultimate solution for the optimum circulation
of air in the relatively more limited space of a cabin. They prevent
unhealthy cold, condensation and mildew, and protect your mattress.
What is more, the simple Click&Roll roll-up system means that the
storage space under your bed is accessible within seconds.
Comfortis® slat bases are traditionally crafted and fully custom-made.
In a manually or electrically operated design. Our revolutionary and
patented technology enables the complete adjustment of your bed base
in zones in the position that you personally find most comfortable.
With manually adjustable head and/or foot sections if you wish.
+31 (0) 514 68 13 17
Comfortis®, ‘t Noard 45, 8721 GB Warns, the Netherlands
e-mail: [email protected], www.comfortis.nl
Seati Nautic
ng & al
Bedd
in
SLAT BASES
g
Comfortis® specializes in hand-made slat bed bases.
Our innovative system is the only patented one in the
Netherlands, as a result of the ingenious new composition
and technology applied. We have three designs in our range.
Sleepshape® Standard
The Sleepshape®Standard is a simply and flexibly installed
slat base system consisting of 32 bowed and laminated 8 mmthick beechwood slats that can be supplied in any required
shape and size. The standard maximum width is 100 cm, and
140 cm for double beds. The length is 205 cm and the height is
a mere 50 mm. Our slat base system has outstanding air
circulation and moisture control properties. Moisture problems
are absolutely a thing of the past. The integrated zone adjustment
makes it possible to regulate the hardness and resilience of the
slats. The entire slate base system lies loose in the bed frame, so
that it is very simple to take out for access to the hatches beneath.
The system is easily rolled up and can be uncoupled at any
required point.
Sleepshape® Handoperated
The Sleepshape® Handoperated is a simply and flexibly installed
slat base system consisting of 32 bowed and laminated 8mmthick beechwood slats with a manually adjustable head section.
De Sleepshape® Handoperated can also be supplied in any
required shape and size. The standard dimensions are 100 cm x
205 cm with a height of 50 mm. The system lies loose in the bed
frame, so that it is very simple to take out for access to the hatches
beneath. In addition, the system is easily rolled up and can be
uncoupled at any required point. The widths of the adjustable
head sections are 40, 50, 60 and 70cm.
Sleepshape®Gold
This is a revolutionary, electrically operated slat base system
with bowed laminated 8-mm thick beechwood slats that can be
fitted into practically every shape of bed. It is supplied with
infrared remote control and emergency manual control, so that
the system can be operated by hand if there is a power outage.
The total installation height is a mere 110 mm (excluding the 18
mm multiplex baseboard). The Sleepshape®Gold is a single bed
unit for a maximum load of 125 kg. Since the base is mounted
on the centre of the bed frame, it is quite simple for you to reach
under the foot section and head section. Due to a number of
ingenious hinges, the joint of the bed hatch rises 110 mm and
you can easily create storage space inside the bed frame. The
construction ensures that the Sleepshape®Gold never becomes
wedged against the back wall. When combined with a gas spring
or electrical motor, you can create the ultimate in terms of
comfort and space. The attention to detail is visible everywhere.
The Sleepshape®Gold consists of 6 sections: the foot, upper leg,
sitting and support, lower back, upper back and head sections.
The head, back and foot sections are infinitely variable using the
remote control. An ingeniously built-in pressure system provides
support for the lower part of the spinal column.
+31 (0) 514 68 13 17
Comfortis®, ‘t Noard 45, 8721 GB Warns, the Netherlands
e-mail: [email protected], www.comfortis.nl