Avnet Embedded.
With you every step of the way.
Datasheet
G190EAN01.0
Date: May 2013
www.avnet-embedded.eu
If you require a touch panel solution.
For information on touch sensors, sensor driving and touch panel bonding
solutions, scan the QR code or click the URL
www.avnet-embedded.eu/products/displays/.html
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
■ Preliminary Specification
□ Final Specification
Module
19.0” SXGA Color TFT-LCD
Model Name
G190EAN01.0
Customer
Date
Checked &
Approved by
Vito Huang
Approved by
document version 0.3
5/ 9, 2013
Prepared by
Ginger Lin
Note: This Specification is subject to
change without notice.
Date
5/ 9, 2012
Audio-Video Business Unit /
AU Optronics corporation
1/28
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
Record of Revision
Version & Date Page
0.1
2012/05/29
All
4
5
Old Description
Frist Edition for Customer
Optical ResponseTime [msec]:
TBD (Typ, on/off)
Power Consumption[Watt]:
LED: 17.28 (W) + LVDS: 4.7 (W)
Optical ResponseTime [msec]: TBD
6
Color/ Chromaticity Coordinates: TBD
Contrast Ratio Min. 800
0.2
2012/11/8
9
13
15
25
document version 0.3
Power Consumption [Watt]:
LED: 14.4 (W) + LVDS: 3.5 (W) (typ)
Optical ResponseTime [msec] : Rising:
Typ.13; Max. 18
Falling: Typ.12; Max. 17
Rising + Falling: Typ.25; Max.35
Update Color/ Chromaticity Coordinates
Contrast Ratio Min. 700
ICC: Typ. 0.94; Max. 1.1; Condition:
Vin=5V, All Black Pattern, at 60Hz
ICC: Typ. 0.7; Max. 0.9; Condition:
Vin=5V, 2dot checker Pattern, at 60Hz
IRush: Typ. 2.1; Max.2.5
IRush: Typ. 2.7; Max.3.4
PCC: Typ. 4.7; Max. 5.5; Condition:
Vin=5V, All Black Pattern, at 60Hz
PCC: Typ. 3.5; Max. 4.5; Condition:
Vin=5V, 2dot checker Pattern, at 60Hz
Note 1: The H-Stripe pattern
Note 1: The 2dot checker Pattern
Note 7: Subchecker Pattern
Delete
VCC: Min.; Typ. 12; Max.
VCC: Min. 10.8; Typ. 12.0; Max.13.2
PVCC: Typ. 17.28; Max.20.4
PVCC: Typ. 14.4; Max.15.8
IVCC: Typ. 1.44; Max.1.70
Irush LED:Typ. TBD; Max.TBD
IVCC: Typ. 1.2; Max.
Irush LED: Typ. 1.7; Max.2.1
Add Note 3
Update Drawing
Add “Analog control voltage: 0~3.3V”
Add “Note 6”
22
24
Optical ResponseTime [msec]:
25 (Typ, on/off)
Delete
15
2013/5/9
Add “Handling Precautions Item 13)”
Flicker [dB]: Max. -20dB
27~28
0.3
New Description
Update Power Sequence Timing chart
Pin 9 “Dimming“
Update “Dimming (or Analog Control
Voltage 0~ 3.3V)”
2/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
Contents
1. Handling Precautions .................................................................................................................. 4
2. General Description ..................................................................................................................... 5
2.1 Display Characteristics ........................................................................................................................ 5
2.2 Optical Characteristics......................................................................................................................... 6
3. Functional Block Diagram.........................................................................................................10
4. Absolute Maximum Ratings......................................................................................................11
4.1 Absolute Ratings of TFT LCD Module ............................................................................................. 11
4.2 Absolute Ratings of Backlight Unit ................................................................................................... 11
4.3 Absolute Ratings of Environment ...................................................................................................... 11
5. Electrical characteristics ..........................................................................................................13
5.1 TFT LCD Module ............................................................................................................................. 13
5.2 Backlight Unit.................................................................................................................................... 15
6. Signal Characteristic .................................................................................................................16
6.1 Pixel Format Image ........................................................................................................................... 16
6.2 The Input Data Format ...................................................................................................................... 17
6.4 Interface Timing................................................................................................................................. 20
6.5 Power ON/OFF Sequence................................................................................................................. 22
7. Connector & Pin Assignment ...................................................................................................23
7.1 TFT LCD Module ............................................................................................................................. 23
7.2 Backlight Unit.................................................................................................................................... 24
8. Reliability Test ............................................................................................................................25
9. Shipping Label and Packaging.................................................................................................26
9.1 Shipping Label................................................................................................................................... 26
9.2 Packaging .......................................................................................................................................... 26
10. Mechanical Characteristic ......................................................................................................27
document version 0.3
3/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
1. Handling Precautions
1)
2)
3)
4)
5)
6)
Since front polarizer is easily damaged, pay attention not to scratch it.
Be sure to turn off power supply when inserting or disconnecting from input connector.
Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of LED light bar edge. Instead, press at the far ends of
LED light bar edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (IEC60950 or
UL1950), or be applied exemption.
13) Avoid stressing front bezel position when doing mechanical design.
document version 0.3
4/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
2. General Description
G190EAN01.0 is a Color Active Matrix Liquid Crystal Display composed of a TFT-LCD panel, a driver circuit,
and a backlight system. The screen format is intended to support the SXGA (1280(H) x 1024(V)) screen and
16.7M colors. All input signals are 2-channel LVDS interface compatible.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 oC condition:
Items
Screen Diagonal
Active Area
Pixels H x V
Pixel Pitch
Pixel Arrangement
Display Mode
Unit
Specifications
482.6 (19.0" )
[mm]
376.32 (H) x 301.06 (V)
[mm]
1280(x3) x 1024
0.294 (per one triad) x 0.294
[mm]
R.G.B. Vertical Stripe
2
White Luminance
[cd/m ]
Optical ResponseTime
[msec]
Contrast Ratio
Normally Black
300 (center, Typ) @ 80mA
1000 : 1 (Typ)
25 (Typ, on/off)
Nominal Input Voltage VDD
[Volt]
+5.0 V
Power Consumption
[Watt]
LED: 14.4 (W) + LVDS: 3.5 (W) (typ)
Weight
[Grams]
1600 (TYP)
Physical Size (H x V x D)
Electrical Interface
[mm]
Surface Treatment
RoHS Compliance
document version 0.3
Dual channel LVDS
Anti-Glare treatment
Support Color
Temperature Range
Operating
Storage (Non-Operating)
396 (H) x 324 (V) x 17.0 (D) (Typ)
16.7M colors
[oC]
[oC]
0 to +50
-20 to +60
RoHS Compliance
5/28
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature):
Item
Viewing Angle
Luminance Uniformity
Optical Response Time
Unit
[degree]
[%]
[msec]
Color / Chromaticity
Coordinates
(CIE)
White Luminance
(At LED= 80mA)
[cd/m2 ]
Contrast Ratio
Cross Talk (At 60Hz)
document version 0.3
[%]
Conditions
Min.
Typ.
Max.
Note
Horizontal
CR = 10
(Right)
(Left)
75
75
89
89
-
Vertical
CR = 10
(Up)
(Down)
75
75
89
89
-
75
80
-
Rising
-
13
18
Falling
-
12
17
Rising + Falling
--
25
35
Red x
0.601
0.651
0.701
Red y
0.292
0.342
0.392
Green x
0.269
0.319
0.369
Green y
0.567
0.617
0.667
Blue x
0.095
0.145
0.195
Blue y
0.010
0.060
0.110
White x
0.263
0.313
0.363
White y
0.279
0.329
0.379
240
300
-
4
700
1000
-
4
-
-
1.5
5
9 Points
1
2, 3
4, 6
4
6/28
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
Note 1: Definition of viewing angle, measured by ELDIM (EZContrast 88)
Viewing angle is the measurement of contrast ratio≧10, at the screen center, over a 180° horizontal and
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows;
90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction
is typically perpendicular to the display surface with the screen rotated about its center to develop the desired
measurement viewing angle.
Note 2: 9 points position
90 %
50 %
10 %
10 %
50 %
90 %
Note 3: The luminance uniformity of 9 points is defined by dividing the maximum luminance values by the
minimum test point luminance. And measured by TOPCON SR-3
δW9 =
document version 0.3
Minimum Luminance of 9 points
Maximum Luminance of 9 points
7/28
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
Note 4: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be executed after
lighting Backlight for 30 minutes in a stable, windless and dark room.
Photo detector
Field=2°
50 cm
LCD Panel
TFT-LCD Module
Center of the screen
Note 5: Definition of Cross Talk (CT) and measured by TOPCON SR-3
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
document version 0.3
8/28
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
Note 6: Definition of response time, measured by WESTAR TRD-100A
The output signals of photo detector are measured when the input signals are changed from “Full Black” to
“Full White” (rising time), and from “Full White” to “Full Black” (falling time), respectively. The response time
is interval between the 10% and 90% of amplitudes. Please refer to the figure as below.
Tr F
%
Optical
response
document version 0.3
TrR
100
90
White
Black
White
10
0
9/28
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
3. Functional Block Diagram
The following diagram shows the functional block of the 19.0 inches Color TFT-LCD Module:
ASIC
+ 5V
Connector
LVDS
LVDS
Receiver
G1024
Timing
Controller
TFT-LCD
1280*(3)*1024
Pixels
RSDS
Transmitter
X-Driver IC
G1
D1
DC/DC
Converter
(Integrate
level shift)
D3840
LED B/L
Gamma
Correction
DC POWER
LED driver
I/F PCB Interface:
FI-XB30SSL-HF15 / MSBKT2407P30HB
Mating Type:
FI-X30HL (Locked Type)
FI-X30H (Unlocked Type)
document version 0.3
10/28
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
4. Absolute Maximum Ratings
Absolute maximum ratings of the module are as following:
4.1 Absolute Ratings of TFT LCD Module
Item
Logic/LCD Drive
Voltage
Symbol
Min.
Max.
Unit
Conditions
VDD
-0.3
+5.5
[Volt]
Note 1, 2
4.2 Absolute Ratings of Backlight Unit
Item
LED Power Current
Symbol
Min.
Max.
Unit
Conditions
Iled
-
1.7
[A] rms
Note 1, 2
Conditions
4.3 Absolute Ratings of Environment
Item
Symbol
Min.
Max.
Unit
Operation Humidity
HOP
5
90
[%RH]
Storage Humidity
HST
90
[%RH]
Operating Temperature
Storage Temperature
document version 0.3
TOP
TST
0
-20
5
+50
+60
[oC]
[oC]
Note 3 & 4
11/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
Note 1: With in Ta= 25℃
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
Operating Range
Storage Range
Note 4: Operation Temperature + 60°C is defined as panel surface termperature.
document version 0.3
12/28
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows:
Symble
Parameter
Min.
Typ.
Max.
Unit
4.5
5.0
5.5
[Volt]
Condition
VCC
Logic/LCD Drive Voltage
ICC
Input Current
-
0.7
0.9
[A]
Vin=5V, 2dot checker
Pattern, at 60Hz
IRush
Inrush Current
-
2.7
3.4
[A]
Note 2
PCC
VCC Power
-
3.5
4.5
[Watt]
VCCrp
Allowable Logic/LCD Drive
Ripple Voltage
-
-
300
[mV]
p-p
±10%
Vin=5V , 2dot checker
Pattern, at 60Hz
With panel loading
Note 1: The 2dot checker Pattern is defined as below:
document version 0.3
13/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
Note 2: Measurement conditions:
+5.0V
D6
D5
D2
D1
Q3
AO6402
G
R1
47K
R2
(LCD Module Input)
S
C3
+12.0V
2
C1
1uF/16V
SW MAG-SPST
Q3
AO6402
G
1K
SW1
VCC
D1
D2
D5
D6
(High to Low)
Control
Signal
F1
S
0.01uF/25V
VR1
1
47K
C2
1uF/25V
5.0V
90%
0V
10%
470 us
VDD rising time
document version 0.3
14/28
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
5.2 Backlight Unit
Following characteristics are measured under a stable condition at 25 C (Room Temperature):
o
Symbol
Parameter
Min.
Typ.
Max.
VCC
Input Voltage
10.8
12.0
13.2
[Volt]
IVCC
Input Current
1.2
PVCC
Power Consumption
14.4
15.8
Irush LED
Inrush Current
-
1.7
2.1
Input Voltage
0
-
3.3
0.2
20
Analog Control
Dimming Frequency
FPWM
IF
VF
PLED
LED Lifetime
Swing Voltage
3
3.3
5
Dimming Duty Cycle
10
-
100
LED Forward Current
LED Forward Voltage
LED Power
Consumption
80
Unit
Remark
[A]
100% PWM Duty
[Watt]
100% PWM Duty
[A]
at rising time=470us
V
[kHz]
V
%
mA
-
-
-
Volt
-
3.2
3.6
Volt
-
-
-
-
13.8
15.6
50,000
Watt
Hrs
Ta = 25oC
IF =80 mA, Ta = 25 C
o
IF =80 mA, Ta = 25oC
IF=80 mA, Ta= 25oC
Note 1: Ta means ambient temperature of TFT-LCD module.
Note 2: VCC, Ivcc, PVCC , Irush LED are defined for LED B/L.(100% duty of PWM dimming)
Note 3: IF, VF , PLED are defined for LED Light Bar.
Note 4: If G190EAN01.0 module is driven by high current or at high ambient temperature & humidity condition. The
operating life will be reduced.
Note 5: LED life means brightness goes down to 50% initial brightness.
Note 6: Two kind types for adjusting brightness: PWM and Analog.
document version 0.3
15/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
1
2
1279 1280
1st Line
R GB R GB
R GB R GB
1024th Line
R GB R GB
R GB R GB
document version 0.3
16/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
6.2 The Input Data Format
Note1: Normally DE mode only. VS and HS on EVEN channel are not used.
Note2: Please follow VESA.
Note3: 8-bit in
document version 0.3
17/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a
differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be
SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels
while the second LVDS port(RxExxx) transmits even pixels.
PIN # SIGNAL NAME
DESCRIPTION
1
RxOIN0-
Negative LVDS differential data input (Odd data)
3
RxOIN1-
Negative LVDS differential data input (Odd data)
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
RxOIN0+
RxOIN1+
RxOIN2-
RxOIN2+
VSS
Positive LVDS differential data input (Odd data)
Positive LVDS differential data input (Odd data)
Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
Power Ground
RxOCLKIN-
Negative LVDS differential clock input (Odd clock)
RxOIN3-
Negative LVDS differential data input (Odd data)
RxOCLKIN+
RxOIN3+
RxEIN0-
RxEIN0+
VSS
Positive LVDS differential clock input (Odd clock)
Positive LVDS differential data input (Odd data)
Negative LVDS differential data input (Even data)
Positive LVDS differential data input (Even data)
Power Ground
RxEIN1-
Negative LVDS differential data input (Even data)
VSS
Power Ground
RxEIN1+
Positive LVDS differential data input (Even data)
RxEIN2-
Negative LVDS differential data input (Even data)
RxECLKIN-
Negative LVDS differential clock input (Even clock)
RxEIN2+
RxECLKIN+
RxEIN3-
RxEIN3+
VSS
VSS
Positive LVDS differential data input (Even data)
Positive LVDS differential clock input (Even clock)
Negative LVDS differential data input (Even data)
Positive LVDS differential data input (Even data)
Power Ground
Power Ground
NC
Do not connect ( for AUO test)
VCC
+5.0V Power Supply
VCC
+5.0V Power Supply
VSS
VCC
document version 0.3
Power Ground
+5.0V Power Supply
18/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
Note1: Start from left side
Connector
1
30
VCC
RxOIN0-
Note2: Input signals of odd and even clock shall be the same timing.
Note3: Please follow VESA.
document version 0.3
19/28
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
6.4 Interface Timing
6.4.1 Timing Characteristics
Signal
Vertical
Section
Horizontal
Section
Clock
Frame Rate
Item
Symbol
Active
Tdisp(v)
1024
Th
780
Period
Tv
Blanking
Tbp(v)+Tfp(v)+PWvs
Active
Tdisp(h)
Period
Blanking
Tbp(h)+Tfp(h)+PWhs
Frequency
Freq.
Period
Frequency
Min
1032
8
640
140
Typ
Max
Unit
1024
1024
Th
844
2047
Tclk
204
-
Tclk
67.5
MHz
1066
42
640
1150
126
22.2
18.52
14.81
1/Tv
50
60
75
54
Th
640
Tclk
45
Th
Tclk
ns
Hz
Note : DE mode only
document version 0.3
20/28
www.avnet-embedded.eu
AU OPTRONICS CORPORATION
Vsync
Hsync
DE
RGB Data
CLK
Hsync
DE
RGB Data
(Odd)
RGB Data
(Even)
N
Line
Tfp(v)
PWhs
PWvs
Invalid Data
Tv
2
Line
3
Line
4
Tdisp(v)
Line
N
Line
Th
Invalid Data
Invalid Data
Tbp(v)
1
Pixel Pixel Pixel
M-3
M-1
M-5
Invalid Data
Line
Pixel Pixel
9
7
Pixel Pixel Pixel
M-2 M
M-4
Tclk
Pixel
5
Pixel Pixel Pixel
10
12
8
Tfp(h)
Pixel
3
Pixel
6
Tdisp(h)
Pixel
1
Pixel
4
Tbp(h)
Invalid Data
Pixel
2
Pixel
11
Invalid Data
21/28
document version 0.3
G190EAN01.0
Product Specification
6.4.2 Timing Diagram
www.avnet-embedded.eu
Product Specification
G190EAN01.0
AU OPTRONICS CORPORATION
6.5 Power ON/OFF Sequence
VDD power and LED on/off sequence is as follows. Interface signals are also shown in the chart. Signals
from any system shall be Hi-Z state or low level when VDD is off.
Power Sequence Timing
Power Sequence Timing
Parameter
Typ.
Max.
30
40
50
T4
0.5
-
10
T6
10
-
-
T8
10
T10
110
T12
0
Min.
T1
0.5
T3
200
T5
10
T7
0
T2
T9
document version 0.3
Value
-
-
10
--
-
-
-
10
50
-
T11
0
16
T13
1000
-
Units
ms
-
10
-
22/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
7. Connector & Pin Assignment
Physical interface is described as for the connector on module.These connectors are capable of
accommodating the following signals and will be following components.
7.1 TFT LCD Module
7.1.1 Connector
Connector Name / Designation
Interface Connector / Interface card
Manufacturer
JAE / STM
Type Part Number
Mating Housing Part Number
7.1.2 Pin Assignment
Pin#
Signal Name
1
RxOIN0-
5
RxOIN2-
3
7
9
RxOIN1VSS
RxOCLKIN+
11
RxOIN3+
15
RxEIN1-
13
17
19
21
23
25
27
29
RxEIN0+
FI-XB30SSLA-HF15 / MSBKT2407P30HB
FI-X30HL
FI-X30H (Unlocked Type)
Pin#
Signal Name
2
RxOIN0+
6
RxOIN2+
4
RxOIN1+
8
RxOCLKIN-
12
RxEIN0-
10
14
16
RxOIN3-
VSS
RxEIN1+
VSS
18
RxEIN2-
RxECLKIN+
22
RxEIN3-
VSS
26
NC
VCC
30
VCC
RxEIN2+
RxEIN3+
VSS
document version 0.3
20
24
28
RxECLKINVSS
VCC
23/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
7.2 Backlight Unit
Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.
Connector Name / Designation
LED Connector / Backlight
Manufacturer
STM
Type Part Number
MS24019R
Mating Type Part Number
P24019
7.2.1 Signal for LED connector
Pin #
Symbol
Pin Description
1
+12V
Power +12V
3
+12V
2
4
5
6
Power +12V
NC
NC
Power +12V
GND
GND
GND
GND
GND
7
GND
EN
Enable(0V:disable, 5V:Enable)
(or Analog Control Voltage)
(Analog Control Voltage 0~3.3V)
8
9
+12V
document version 0.3
Dimming
PWM; duty 10%~ 100%
24/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
8. Reliability Test
Environment test conditions are listed as following table.
Items
Temperature Humidity Bias (THB)
High Temperature Operation (HTO)
Low Temperature Operation (LTO)
High Temperature Storage (HTS)
Required Condition
Ta= 50 C, 80%RH, 300hours
Ta= 50oC, 300hours
Ta= 0oC, 300hours
Ta= 60oC, 300hours
Low Temperature Storage (LTS)
Ta= -20oC, 300hours
Vibration Test
(Non-operation)
Acceleration: 1.5 G
Wave: Random
Frequency: 10 - 200 - 10 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)
Shock Test
(Non-operation)
Acceleration: 50 G
Wave: Half-sine
Active Time: 20 ms
Direction: ±X, ±Y, ±Z (one time for each Axis)
Drop Test
Height: 60 cm, package test
Thermal Shock Test (TST)
On/Off Test
ESD (Electrostatic Discharge)
Altitude Test
Note
o
1
-20 oC /30min, 60/ oC 30min, 100 cycles
On/10sec, Off/10sec, 30,000 cycles
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec,
9 points, 25 times/ point.
2
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
9 points, 25 times/ point.
Operation:10,000 ft
Non-Operation:30,000 ft
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-20oC to 60oC, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.
Note 3:
Water condensation is not allowed for each test items.
Each test is done by new TFT-LCD module. Don’t use the same TFT-LCD module repeatedly for
reliability test.
The reliability test is performed only to examine the TFT-LCD module capability.
To inspect TFT-LCD module after reliability test, please store it at room temperature and room humidity
for 24 hours at least in advance.
No function failure occurs.
document version 0.3
25/28
www.avnet-embedded.eu
Product Specification
AU OPTRONICS CORPORATION
G190EAN01.0
9. Shipping Label and Packaging
9.1 Shipping Label
The label is on the panel as shown below:
G190EAN01.0
Note 1: For Pb Free products, AUO will add
for identification.
Note 2: For RoHS compatible products, AUO will add
Note 3: For China RoHS compatible products, AUO will add
for identification.
for identification.
Note 4: The Green Mark will be presented only when the green documents have been ready by AUO Internal
Green Team.
9.2 Packaging
document version 0.3
26/28
www.avnet-embedded.eu
www.avnet-embedded.eu
document version 0.3
10. Mechanical Characteristic
AU OPTRONICS CORPORATION
Product Specification
27/28
G190EAN01.0
www.avnet-embedded.eu
document version 0.3
AU OPTRONICS CORPORATION
Product Specification
28/28
G190EAN01.0
www.avnet-embedded.eu
Avnet Embedded OFFICES
Denmark
Avnet Embedded
Avnet Nortec A/S
Ellekær 9
2730 Herlev
Phone: +45 3678 6250
Fax: +45 3678 6255
denmark@ avnet-embedded.eu
Finland
Avnet Embedded
Avnet Nortec Oy
Pihatörmä 1 B
02240 Espoo
Phone: +358 20 749 9 260
Fax: +358 20 749 9 280
finland @ avnet-embedded.eu
FrancE
Avnet Embedded
Avnet EMG France SA
Parc Club du Moulin à Vent, Bât 10
33, rue du Dr Georges Lévy
69693 Vénissieux Cedex
Phone: +33 4 78 77 13 92
Fax: +33 4 78 77 13 97
bron @ avnet-embedded.eu
GERMANY (AUSTRIA, CZECH REPUBLIC,
HUNGARY, POLAND, SWITZERLAND)
Avnet Embedded
Avnet EMG GmbH
Gruber Straße 60c
85586 Poing
Phone: +49 8121 775 500
Fax: +49 8121 775 550
poing @ avnet-embedded.eu
UNITED KINGDOM (IRELAND)
Avnet Embedded
5a Waltham Park
White Waltham
Maidenhead
Berkshire, SL6 3TN
Phone: +44 1628 518900
Fax: +44 1628 518901
uk@ avnet-embedded.eu
Avnet Embedded
Avnet EMG GmbH
Lötscher Weg 66
41334 Nettetal
Phone: +49 8121 775 500
Fax: +49 8121 775 550
nettetal@ avnet-embedded.eu
ITALY (PORTUGAL, SPAIN)
Avnet Embedded
Avnet EMG Italy SRL
Via Manzoni, 44
20095 Cusano Milanino
Phone: +39 02 660 92 1
Fax: +39 02 660 92 498
milano @ avnet-embedded.eu
Avnet Embedded
Avnet EMG France SA
14 avenue Carnot
91349 Massy Cedex
Phone: +33 1 64 47 29 29
Fax: +33 1 64 47 99 99
paris @ avnet-embedded.eu
NETHERLANDS (BELGIUM, LUXEMBOURG)
Avnet Embedded
Avnet B.V.
Takkebijsters 2
4817 BL Breda
Phone: +31 76 5722400
Fax: +31 76 5722404
benelux @ avnet-embedded.eu
Avnet Embedded
Avnet EMG France SA
Les Peupliers II
35 avenue des Peupliers
35510 Cesson-Sévigné
Phone: + 33 2 99 77 37 02
Fax: + 33 2 99 77 37 01
rennes @ avnet-embedded.eu
SWEDEN (NORWAY)
Avnet Embedded
Avnet Nortec AB
Esplanaden 3 D
172 67 Sundbyberg
Phone: +46 8 564 725 50
Fax: +46 8 760 01 10
sweden @ avnet-embedded.eu
All trademarks and logos are the property of their
respective owners. No guarentee as to the accuracy,
completeness or reliability of any information.
Subject to modifications and amendments.
June 2013