z090 Installation Manual

KEYPAD
PROGRAMMING
MODULE
POWER
BUSY
LOW
VOLTS
GO
ERROR
OK
SIZE
TEST
LEARN
MACRO
CLEAR
GAP
IR
WINDOW
SYSTEM
PAGE
LOAD
LENGTH
IR
TEST
Z•090
KEYPAD
PROGRAMMING
MODULE
PROGRAMMING
MANUAL
EPROM VERSION 026
PC TOOLS VERSION 3.1
ELAN
HOME
TABLE
OF
SYSTEMS
KEYPAD
PROGRAMMING MODULE
CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
FRONT PANEL LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
FRONT PANEL BUTTONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
BACK PANEL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Z•100/Z•150 KEYPAD MEMORY MAP DEFINITIONS . . . . . . . . . . . . . . . . . . . .5-8
Default Preprogrammed IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Function Key Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
System Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Source Select Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Source Key Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
The Favorite Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Global Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Delay Gaps and Transmission Lengths . . . . . . . . . . . . . . . . . . . . . . . . . .8
Z•090 KEYPAD PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-16
A.)
B.)
C.)
D.)
E.)
F.)
G.)
H.)
I.)
Setting Up to Learn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-10
Learning IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Learning System-Level IR Codes to the System Page . . . . . . . . . . . .11
Macro Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-13
Source Select Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Favorite Key Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Global Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Programming Macro Step Delay Gap and
Transmission Lengths . . . . . . . . . . . . . . . . . . . . . . . . .12-13
Testing Learned Codes and Macros . . . . . . . . . . . . . . . . . . . . . . . .13
Clear Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Downloading to the Z•100 Keypad . . . . . . . . . . . . . . . . . . . . . . . .15
Uploading from a Z•100 Keypad . . . . . . . . . . . . . . . . . . . . . . . . . .15
Modifying a Programmed Z•PAD Memory . . . . . . . . . . . . . . . . . . .15
Z•090 PC INTERFACE (Addendum). . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . . .16
Z•PAD FACTORY DEFAULT KEY FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
SYSTEM PAGE COMMANDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Z•SERIES LEARNED COMMANDS PLACEMENT MAP . . . . . . . . . . . . . . . . . . . . . . . .24
CLIENT MACRO PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
CLIENT SOURCE MEMORY MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 1
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
KEYPAD PROGRAMMING MODULE
INTRODUCTION
Right out of the box, Z•PADs can transmit all Z•630 Preamp Controller and Series HD™
HDC2000 Master Control Unit (MCU) system codes. They cannot, however, control any
source equipment functions until they have been “taught” these codes via the Z•090 Keypad
Programming Module.
Z•090/Z•PAD Feature Benefits:
• Easy-to-program up to 13 sources, including macros for each source.
• Design is based on the robust learning technologies found the ELAN Series HD™ MCU
today.
• Upgradeable EPROM technology allows programmer to keep all keypads current with
the latest functionality enhancements.
• Non-Volatile flash memory in both the Z•090 and Z•PAD insures memory retention of
programmed data.
• Allows a single gang keypad to be used––does not limit each keypad with learning
hardware/software.
• Intelligent one-button source select macros makes using the system very easy.
Z•PADs can be programmed in the shop or after installation at a homeowner’s
residence.
• Portable, does not require a PC to capture IR data to program keypads.
• PC software can store IR library and client specific memory maps.
Z•080 Stand-Alone System Applications
The Z•090 is required to teach both system and source control codes to all the Z•PADs in any
stereo receiver-based system.
Z•630 Preamp Controller Applications
The Z•090 is required to teach source control codes to all the Z•PADs in a Z•630 system.
System control codes are preprogrammed.
Series HD™ Applications
It is not necessary to teach Z•PADs when used in an Series HD™ system. This is done with the
MCUs HDC2060 Learning Infrared Interface card.
There are, however, certain HD applications where the Z•090 is required:
• Programming one-button macros under the Z•100’s source select keys
• Controlling a local source selected by pressing the TV key on the Z•150 keypad.
Also, if using Z•PADs exclusively with HD installations, you may wish to use the Z•090 to
create IR libraries that can be stored in your PC and accessed for future installations.
Page 2
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
FRONT PANEL LEDS
POWER
The POWER LED Indicates AC power is applied to the Z•090 via the
11VAC power cube.
BUSY
The BUSY LED will illuminate when the Z•090 is transferring data to
the Z•100 Pad or a PC, or when the unit is in process of learning an
IR code through the IR Window.
LOW VOLTAGE
The LOW VOLTAGE LED will only illuminate if the main (120V) AC
input to the 11V Power Cube drops below 105VAC. This low voltage
condition must be corrected for proper operation of the Z•090.
GO
ERROR
OK
The GO LED will illuminate after the learn button has been pressed,
indicating the unit is ready to capture IR codes from a hand held
remote. It will also illuminate while programming a macro.
The ERROR LED will illuminate if IR data received at the IR window
cannot be learned.
The OK LED will light after a successful capture of an IR code or
when building a macro string.
SIZE
When programming macros, the SIZE LED will wink indicating four
choices for Transmission Length or Delay Gap when either of those
buttons are pressed.
TEST
The TEST LED will illuminate when the test button is pressed. This
indicates that a learned IR code or macro string is being transmitted
via the IR LEDs on the back of the Z•090.
IR WINDOW
The IR WINDOW is the Z•090’s receiver; you point the remote you
wish to learn at this window to teach the Z•090 IR codes.
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 3
ELAN
HOME
SYSTEMS
INSTALLATION MANUAL
FRONT PANEL BUTTONS
LEARN
The LEARN button initiates an IR signal data capture.
SYSTEM PAGE This feature is intended for Z•PADs using the Z•080 Stand-Alone Keypad
Interface. In this configuration the stereo receiver’s Power, Mute, Volume
Up/Down IR codes need to be available from all keypads at all times,
regardless of the selected source.
MACRO
LOAD
The LOAD button will download captured IR codes and programmed
macros to the keypad and Z•090 flash memories. This button is also used
in conjunction with a power key press on the keypad to upload data from
a keypad into the Z•090 (Z•090 software version 011 or higher).
CLEAR
The CLEAR button will allow you to clear an individual learned key press,
a macro string or the entire Z•090 memory map. Once a key has been
cleared, the default ELAN codes are restored into the Z•PAD.
GAP
LENGTH
Page 4
This button puts the Z•090 into MACRO PROGRAMMING MODE.
The GAP button allows you to set the delay gap between individual steps
in a macro string.
The LENGTH button allows you to set the IR transmission length
associated with any step in a macro string.
IR TEST
The IR Test button will allow you to retransmit each code you have
learned, or each macro string you have programmed.
TEST IR
The three LED “blasters” on the back of the Z•090 will transmit IR codes
or macro strings when the Test IR button is pressed. By placing the Z•090
in front of your source equipment, you will be able to verify learned
codes will control your source equipment properly.
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
BACK PANEL CONNECTIONS
11 VAC––This is the input jack for the 11VAC Power Cube.
NOTE:
You must ONLY use
the Z•090’s 11 VAC
power cube with the
learner–– no other “off
the shelf” power cube
may be used to power
the Z•090.
KEYPAD DOWNLOAD PORT––This port will download or upload learned data between
the Z•090 and the Z•100 keypad.
RS232 COMPUTER INTERFACE––This port is for interfacing the Z•090 with a PC or laptop.
The 11VAC Power Cube, Download Cable, RS-232 Interface Cable, and PC programming disc
are included with the Z•090.
Z•100/Z•150 KEYPAD MEMORY MAP
Etc.
Tape Page Codes
CD Page Codes
Tuner Page Codes
System Page Codes
Default
Preprogrammed Codes
The Z•PAD memory map contains 15 pages of IR codes and macro strings. Each of the
possible 13 sources on the Z•PAD has its own page of codes for all the function keys. There is
also a factory default and learned system page of codes. IR codes which are captured by the
Z•090 are first stored in its working “RAM” memory. Pressing the LOAD button on the Z•090
transfers that data to non-volatile flash memory in both the Z•090 and the Z•PAD. Flash
memory allows program and data information to be retained in the both Z•090 and
the Z•PAD even if power is removed from these devices.
Default Preprogrammed IR Codes
Every key press on a preprogrammed Z•PAD will transmit a unique ELAN default IR code,
recognized by the Z•630 Preamplifier or Series HD™ MCU Chassis. There are a total of 62
primary and shifted default ELAN key codes available.
The System Command Table on Page 18 defines the pre-programmed Z•630 and Series HD™
System codes.
A function key with no learned data will always send an ELAN default code. The only
exceptions are:
• The shift key ( ) sets up the internal shift state of the keypad; it sends no code and is
not learnable.
• The Z•150’s TV source select button and function keys have no ELAN default codes,
but can be learned. This way the homeowner will not inadvertently be controlling the
system audio while pressing unprogrammed TV function keys.
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 5
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
It is important to accurately chart all the learned codes for each source and their keycap
assignments. For Z• Series systems (Z•630/Z•080), use the Learning Page and Macro Page
located at the back of this manual to record your programming. Make sure to make multiple
copies of these pages first. For Series HD™, use the Keypad & Handheld Remote Worksheets
found in the HD Installation Manual.
Function Key Pages
There are 43 discrete function keys that can be programmed for up to 13 sources in a Z•PAD.
A function key press can perform one of the following functions:
• Transmit a learned code associated with the selected source if programmed, otherwise:
• Transmit a system page learned code if programmed, otherwise:
• Transmit the Default ELAN code
System Page
The SYSTEM PAGE button allows you to learn system-level codes (for example, Receiver
POWER, Receiver VOLUME UP, etc.) for each of the 62 key strokes on that page, eliminating
the need to learn these codes under each source page. Once you learn a code on to the
System Page, pressing an unprogrammed function key on a source page will transmit the
system page code instead of the ELAN default code.
Source Select Key
The Source Select key will re-map the Z•PAD to a source page in memory where source
specific IR codes are stored. A Source Select key press can also perform one of the following
functions:
NOTE:
You can learn an IR
code to a Source
Select key AND
program a macro to
the same key. When
that key is pressed,
you will get the macro
string. When that key
is programmed as a
step in global or
favorite macro string,
the learned Source
Select function will
transmit for that step.
NOTE:
Transmitting the ELAN
code first will not
adversely affect the
function of your source
equipment––it will
simply be ignored.
Page 6
• Transmit a default ELAN code and a 13-step “One Button” macro if programmed,
otherwise:
• Transmit a default ELAN code and a learned source select button code if programmed,
otherwise:
• Transmit a default ELAN code
For ELAN Z•630 or Series HD™ MCU, transmitting the default ELAN code will cause the
preamp to turn the zone on, select the audio source, switch the preamp IR router and unmute
the zone (or unmute the local Z•025 Speaker relay)
A “learned” source key press will automatically transmit an ELAN default code first, then the
learned code for the duration of the key press. This is in effect a two-step command string,
where you might want to learn the play command for a CD player on the CD key. Then
whenever CD is pressed, the source is selected and CD play will also transmit.
For Z•080 applications, learn each of the stereo receivers input select codes to their
corresponding source select key on the Z•PAD.
Source Key Macros
Source Macro steps are defined as follows:
STEP 0: The default ELAN source select code is automatically inserted (as Step 0) in a source
select key macro string. This ensures that a source button press will always result in ELAN
equipment selecting the proper source, regardless of an additional learned code or macro
string being programmed to that button. Learned source select button codes are entered as a
separate step in a macro string. (They will not automatically be sent as step 0.)
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
NOTE:
If you always want
the first step for a
source key macro to
be transmitted,
press and hold the
SOURCE key, and
while holding the
SOURCE SELECT
key on the Z•PAD
press the MACRO
button on the Z•090.
This starts the
macro programming
sequence for that
source key with the
first step locked in
SYSTEMS
KEYPAD
PROGRAMMING MODULE
STEP 1: Step One is a “conditional step” in a source select macro. Any learned or default ELAN
code can be programmed as Step 1 in a source macro string (not just the power command).
For Z•630 operation––Step 1 is omitted from the macro string if the source selected is in
music detect mode (Green source LED is on). If you have programmed the source equipment’s
IR power command to Step 1, it will be omitted if music is detected for that source.
If no music is detected (source LED is Red) then Step 1 is inserted into the macro string––
causing the source equipment to turn on if Step 1 is a power command. If the source equipment is in stand-by mode and music is not detected, Step 1 will turn it off. Pressing the source
select button again will the turn the source back on, resynchronizing it to the system.
Using a Z•080 with +12VDC power sense enabled––Step one (usually the stereo receiver
power command) will be omitted if +12VDC is detected on the keypad sense input line
(originating from a Z-•CUBE plugged into the back of the switched outlet on the receiver.) If
+12VDC is not present on the sense line (receiver is off), then Step 1 will be transmitted,
turning the receiver on.
In Z•080 stand-alone mode with +12V sense disabled or HD mode, Step 1 is always sent––
unconditionally.
STEPS 2 - 13: Any key press combination can be programmed to steps 2 - 13. The
NOTE:
Macros cannot be
imbedded in other
macros. If you
program a macro
key into another
macro, the learned
code (or default
ELAN code) under
that key will be sent
as that step when
the macro executes.
is not counted as a key press, so entering
as one command in the macro string.
key
, then a function key will be recorded
You can program multiple source select buttons in a source macro string. When executed, just
the source select (learned or default) code is transmitted for that step. (Even if there is also a
macro programmed under that source select button) example. Programming VCR, Power, Play,
TV, Power, 0,3,Enter is acceptable.
In a Z•630 application, source select macros programmed to the shifted source pages
(
, TNR,
, CD, etc.) are accessible as “Global” type macros, and the keypad will not send
a Step 0. This is also true for
, DVD and
, DSS in Series HD™ MCU applications.
The Favorite Key
The FAV key on the Z•PAD is a source dependent macro button, and can be programmed for
one of the following functions:
• Transmit 13 different (one for each source) 13 step Macros, if programmed, otherwise:
• Transmit a System Page FAV macro if programmed, otherwise:
• Transmit 13 different (one for each source) learned FAV command, if programmed,
otherwise:
• Transmit a system page learned FAV command, if programmed, otherwise:
• Transmit the default ELAN code.
In Z•630, Series HD™ MCU or Z•080 +12V sense configurations, pressing the FAV button
when no source LEDs are lit will send the system page FAV codes (macro or IR).
In Z•080 stand-alone mode when +12V sense is not used (disabled) and the keypad is dark,
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 7
ELAN
HOME
SYSTEMS
NOTE:
The LEDs on Z•PADs
configured for Z•080
+12V sense disabled
operation have an
8-second time out
after the last key is
pressed (otherwise
they would have to
be left on forever).
Pressing any key will
then turn on the last
source LED.
NOTE:
If you attempt to
program a global
macro multiple times
under different
sources, the last
macro string you
entered will be the
one that is accepted.
KEYPAD
PROGRAMMING MODULE
hitting the FAV button will turn on the last source LED selected and send that sources FAV
codes (macro or IR).
Global Macros
Global macros are source independent macros. That means that regardless of what source is
selected on the keypad, pressing a global macro button will always transmit the same code(s).
There are six GLOBAL Macro Z•PAD Buttons:
(PARTY) (
, PARTY) ( , FAV) ( ,7) ( , 8) (
,9)
A global macro can be programmed in a couple of ways, and the priorities for these keys are
as follows:
• Transmit a single 13-step source independent global macro if programmed, otherwise:
• Transmit the last command learned under that key, otherwise:
• Transmit the Default ELAN code for that key.
Delay Gaps and Transmission Lengths
There are four options for delay gap and transmission length for each macro step. (Source
Select, Favorite or Global)
• Gap Options:
• Length Options:
0.1 sec (default), 1 sec, 3 sec, and 8 seconds.
0.3 sec (default), 0.5 sec, 2 sec, and 4 seconds.
Programming gaps and lengths do not reduce the number of steps available in a macro string.
Z•090 KEYPAD PROGRAMMING
To learn your source component’s IR codes you will need the following:
• Z•090 Keypad Programming Module
• Z•090 11VAC Power Cube
• Keypad Download Cable
• Z•100 Keypad
• Z•150 Direct Access Keypad (if using Z•150’s in the system)
• Source Component Remotes
• Z•SERIES Learned Codes Placement Map
A. SETTING UP TO LEARN
1. The Z•PAD and the Z•090 must be in the same power state before the download
cable is connected between the two (i.e. both are powered UP or both are powered
DOWN).
2. For programming keypads right out of the box:
a) Plug the keypad download cable into the download port on the Z•090, and
then plug the other end of the download cable into the Z•100. Note the keyed
connector alignment on the download cable (see Figures 1 and 2 on the
following page).
Page 8
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
FIGURE 1
Make sure that the
Z•PAD and the Z•090
are either both powered
up or both powered
down before connecting
the download cable.
FIGURE 2
NOTE:
The keypad end of the
download cable is
keyed––it only goes on
the Z•100 header one
way. DO NOT FORCE
IT ON BACKWARDS!
Damage to the keypad,
download cable, or both
could result.
b)
If the Z•090 was not powered up, plug the 11VAC power supply into the AC
POWER input jack on the Z•090 and plug the power cube into an outlet. This will
also apply power to the Z•PAD.
FIGURE 3
11VAC
POWER
CUBE
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 9
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
3. To program a keypad that is already connected to a Z•630, Series HD™ MCU, or Z•080:
a) Make sure that power is OFF to the Z•090 and the Z•630, the MCU, or the
Z•080.
b) Plug the keypad download cable into the download port on the Z•090, and
then plug the other end of the download cable into the Z•100. Note the keyed
connector alignment on the download cable.
c) Plug the 11 VAC power cube into the Z•090 and then into an outlet.
d) The BUSY LED will come one while the Z•090 establishes communication with
the keypad, then turn off.
4. Once the BUSY LED extinguishes, the Tuner LED will illuminate on the Z•PAD. You
can now use it as a keyboard entry device to program the Z•090 with.
B. Learning IR Codes
NOTE:
Make sure you press
and hold the remote
button you are
learning until the
OK LED turns on.
If OK LED comes on
but winks twice after
learning, this
indicates the Z•090
learned a nonrepeating code or
you did not hold the
button down long
enough.
NOTE:
The Z•150 Direct
Access Companion is
required to learn TV
commands or numeric
commands for
system sources.
NOTE:
Source equipment
power commands
should be learned
under the
,POWER
key, as the non-shifted
Power key is intended
to turn the main
system on and off.
Page 10
With the Z•100 keypad connected to the download port on the Z•090:
1. Press a source key (CD), then press a
function key (PLAY)
Z•PADs can learn up to 13 sources
2. Press the LEARN button on the Z•090;
depending on the type of system they
the GO LED will turn on. Once LEARN
are being used in:
is pressed, the GO LED will remain lit
until an IR code is captured. To cancel
Z•100 SOURCE SELECT KEYS AND
SYSTEM SOURCE AVAILABILITY
the learn sequence, press LEARN again.
SOURCE Z•100
SOURCE
Z•630 SERIES STAND3. Aim the CD player’s remote control at
#
FACTORY
SELECT
HD™
ALONE
the front of the Z•090 from approxiDEFAULT
LED COLOR
(Z•080)
KEYCAP
mately 12” away, then press and HOLD
1
TNR
GREEN
√
√
√
the remote’s Play button until the GO
2
CD
GREEN
√
√
√
3
TAPE
GREEN
√
√
√
LED extinguishes. NOTE: Some codes
4
VCR
GREEN
√
√
√
take longer to learn than others.
5
DVD
GREEN
√
√
√
6
DSS
GREEN
√
√
√
4. The Z•090’s BUSY LED will wink
7
*, TNR
RED
√
√
momentarily. Then either the OK LED
8
*, CD
RED
√
√
9
*, TAPE
RED
√
√
will turn on, indicating a successful
10
*, VCR
RED
√
√
capture, or the ERROR LED will light,
11
*, DVD
RED
√
12
*, DSS
RED
√
indicating a problem with learning the
13
TV
RED
√
√
√
code. If you get an error indicator, press
the LEARN button again and retry.
You may have to move the handheld remote closer or further away from the Z•090 to get a
good capture, or you may have released the remote button too early (wait for the OK LED to
turn on). Learning distances may vary from remote to remote. Make sure there is not excessive
sunlight or florescent lighting illuminating the front of the Z•090 while trying to learn. Each
learned command can be tested as you go to verify a good capture. See Section E, Page 13.
5. To learn another key from the same remote, simply press the Z•100 or Z•150 key
you want to learn to (STOP), press the LEARN button on the Z•090, then press and
hold the remote button to be learned. You do not need to repress the source key for
each new code you want to learn from the same remote.
6. To learn keys from a new source remote, select the new source on the Z•100 keypad,
(TUNER), and repeat steps 1 through 5.
7. To learn an IR code for CD FAV, Press CD on the keypad, press FAV on the keypad
then press LEARN on the Z•090.
NOTE:
Once you have learned all your sources’ IR codes into the Z•090, you will need to download this information to the keypad (See G, page 15).
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
IMPORTANT
SYSTEM PAGE
NOTES
In Z•630 or Series
HD™ systems, the
System Page is the
location of the default
ELAN system
commands (i.e. Zone
ON/OFF, Zone MUTE,
Zone Vol. UP/DWN,
Wholehouse Music
ON/OFF, Do-NotDisturb ON/OFF.
These commands are
needed to control
either the Z•630 or
HDC2000 MCU.
Overwriting a system
command with a
learned IR command
will disable the ELAN
system command
located under that key
press. Should you
learn over an ELAN
system-level command, the CLEAR
feature (see Section
F) can be used to
re-set the Z•PAD to
their factory defaults.
KEYPAD
PROGRAMMING MODULE
C. Learning System-Level IR Codes to
the System Page
1. Press the SYSTEM PAGE button on the Z•090. The MUTE LED on the Z•100 will turn
on, indicating that the System Page code you are about to learn will be available under
the same keypad key regardless of what source is selected. (MUTE LED = System Page
Programming)
2. On the Z•100 or Z•150, select the function key you want to learn to (i.e. POWER).
3. Press LEARN on the Z•090. The GO indicator will illuminate.
4. Aim the source remote at the Z•090’s IR window and press and hold the key you wish
to learn until the OK LED turns on.
5. To learn an IR code for FAV on the system page, press SYSTEM PAGE on the Z•090,
then FAV on the keypad, then LEARN.
6. To exit System Page programming, press any source select key on the Z•100. The
Z•100’s MUTE LED will then turn OFF.
D. Macro Programming
SOURCE SELECT MACROS
Z•630 and Series HD™ Applications
To program a source macro to, for example select CD, send the power command if it is
off, select disc 125 then play:
1.
2.
3.
4.
Press and release the source button (CD) on the Z•100, then
Press the MACRO button on the Z•090
Press
,POWER, 1,2,5, Enter, Play, on the Z•100/Z•150
Then press the MACRO button on the Z•090 to terminate the macro string.
NOTE: Source equipment POWER commands should be learned under
PWR is used for main unit On/Off functions.
, POWER, as
Remember the source select command (CD) is automatically sent as Step 0. Also, you do not
want to re-enter the source select button before selecting each source function key; do this
only when you want to change sources.
To eliminate the conditional action of the first step in a Source Select macro (so that it will
always be sent regardless of Z•630 music detect or Z•080 +12 Power sense status)
1. Press and hold the Z•PAD source select key
2. While holding the source select key press the MACRO button on the Z•090.
3. Enter your macro string as described above.
The first step in this macro string will unconditionally be transmitted.
To program a Source key (CD) macro for Stand-Alone Z•080 operation of a stereo receiver:
1. First learn the stereo receiver’s input select IR codes to the Z•PAD’s source keys and
all other receiver commands to the SYSTEM PAGE (i.e. Receiver Power to SYSTEM
PAGE POWER, Receiver Vol. Up/Down to SYSTEM PAGE Vol. Up/Down, Tuner Preset
1 to SYSTEM PAGE 1, etc.).
2. Press the CD button on the Z•PAD
3. Press MACRO on the Z•090
4. Press Power on the Z•PAD. This issues the conditional (step 1) power command to the
receiver––turning it on
5. Press the CD button on the keypad (this is the receiver CD input select command
learned in step 2)
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 11
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
6. Then press 1, 2, 5, Enter and Play on the Z•PAD
7. Terminate the macro string by pressing MACRO on the Z•090
To exit macro programming , press the MACRO button after the last step. Pressing the TEST
button at the end of programming a macro string will test the string and then terminate the
programming sequence. You can press MACRO, then TEST again to retest the string if you like.
NOTE:
To edit a macro string,
simply reprogram it.
Multiple source select and function keys can be programmed in a macro string, simply select
the source, select the function key, select a new source and then a new function key. Source
select keys (ELAN default or learned commands, but not macro strings) can be stored as a step
in a macro.
FAVORITE KEY MACROS
To program a favorite key macro:
1. Select the source key (i.e. Tuner) on the Z•PAD
2. Press the FAV on the Z•100
3. Press the MACRO button on the Z•090
4. Enter the macro steps from the Z•PAD (FM Band Select, Preset 1)
5. Press the MACRO or TEST button to terminate the macro string
To program a System Page FAV macro:
1. Press SYSTEM PAGE on the Z•090
2. Press the FAV on the Z•PAD
3. Press the MACRO button on the Z•090
4. Enter the macro steps from the Z•PAD
5. Press the MACRO or TEST button to terminate the string.
The System Page FAV macro will be transmitted each time an unporgrammed FAV key on a
source page is pressed.
GLOBAL MACROS
NOTE:
If you do not enter a
source key as Step 1
in a global macro,
then you will get the
IR code assoicated
with whatever source
page you were on
when the global
macro key was
pressed (therefore,
always enter a source
select in the first step
of a global macro).
To program a global macro:
1. Press the Global macro key on the Z•PAD you want to program (i.e. PARTY).
2. Press the MACRO button on the Z•090.
3. Select the source you want to control first (i.e. TNR). This is Step 1.
4. Select a function key. This is Step 2.
5. Repeat 4 for each new function key press for that source.
6. Repeat 3 then 4 if you want to control other sources.
7. Press the MACRO or TEST button to terminate the string.
PROGRAMMING MACRO STEP DELAY GAP AND
TRANSMISSION LENGTHS
You may find the need to increase the transmission length of a macro step or insert a delay gap
between adjacent steps to allow the source equipment to turn on or load. Each macro step can
be programmed with one of 4 choices for delay gap and transmission lengths.
Gap Options:
0.1 sec (default), 1 sec, 3 sec, and 8 seconds.
Length Options:
0.3 sec (default), 0.5 sec, 2 sec, and 4 seconds.
Programming gaps and lengths do not reduce the number of steps available in a macro string.
Any step can be modified after it is entered by pressing the GAP or LENGTH buttons, but must
be modified before the next macro step key is pressed.
Page 12
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
To program a macro step gap or length:
1. Select the macro key on the Z•PAD you want to program
2. Press the MACRO button on the Z•090
3. Press the keypad buttons you want in the macro string
To increase the delay gap between the step you are on and the next step you are about to enter:
1. Press the GAP button once. The SIZE LED will wink 2 times––indicating that the second gap option (1 second) has been programmed.
2. Press the GAP button again and the SIZE LED will wink 3 times, indicating the third
gap (3 seconds) has been programmed.
3. Press it again for the fourth gap, press it one more time and you cycle back to the first
(default) gap size of 0.1 seconds.
NOTE:
Don’t forget to press
the MACRO or TEST
button at the end of
programming a macro
to terminate the string.
To increase the transmission length of a macro step:
1. Press the LENGTH button once. The SIZE LED will wink 2 times––indicating that the
second length option (0.5 seconds) has been programmed.
2. Press the LENGTH button again to select the next option (2 seconds) and again for 4
seconds.
You can press the LENGTH or GAP buttons in any order, and as many times as you like to
cycle through the options for that macro step.
E. Testing Learned Codes and Macros
Each time you successfully learn a code or build a macro string you can verify the keypad will
operate the source equipment by pressing the TEST IR button on the Z•090. When pressed,
the TEST LED will illuminate and blue IR Emitters on the back of the Z•090 will wink at the
source equipment. This will give you immediate verification that each new learned code or
macro actually controls the source equipment. The back of the Z•090 must be facing the
source equipment for this test.
To test a learned IR code as you go:
1. After learning a code, press the TEST IR button on the Z•090. The Z•090 will transmit
a learned code for as long as you hold down the TEST button.
To test previously learned SOURCE codes:
1. On the Z•100, press the appropriate Source Select key, then press the function key
you wish to test.
2. Press the TEST IR button on the Z•090.
To test previously learned SYSTEM PAGE codes:
1. Press the SYSTEM PAGE button on the Z•090.
2. Press the Z•PAD function key you wish to test
3. Press the TEST button.
Testing Macros is easy!
1. Select the programmed macro key on the keypad
2. Press the MACRO button on the Z•090
3. Press the TEST button.
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 13
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
The IR emitters on the back of the learner will wink the entire macro string––one time
(including modified gaps and lengths)––at the source equipment stacked behind the Z•090.
If you try to test a function under which no code has been learned, the ERROR LED on the
Z•090 will illuminate.
F. Whoops! I Didn’t Want To Learn That There!
(Clear Functions)
Should you learn the wrong code to a Z•PAD key, simply re-learn the correct code under that
same key. The new code will overwrite the previously learned code.
Pressing and holding
only the CLEAR button
for 3 seconds will erase
the entire learned
contents of the Z•090
IMPORTANT!
The Z•100 Keypad
has a non-volatile
flash memory that can
only be written to “inbulk” (i.e. you have to
rewrite the whole
memory map in the
keypad even if you
only want to modify
just one function key).
Learning just one new
key in an “empty Z•090”
and then downloading
to the Z•PAD will
erase the contents of
the programmed keypad
–– and place just that
one command into
memory.
NOTE:
Clearing a learned
command or macro
string from the Z•090’s
memory does not erase
the memory of a keypad
connected to it. To do
so you will need to
download a modified
memory map to the
Z•100 keypad once you
have finished making all
the modifications in the
Z•090.
Page 14
Should you learn a code to the wrong key you can:
1. Relearn it under the correct Z•PAD key and/or,
2. CLEAR that key
To clear a learned source function key:
1. Select the appropriate source on the Z•100 keypad.
2. Press the function key on the Z•100 or Z•150 that you wish to clear.
3. Press CLEAR on the Z•090. (Do not press and hold the clear button or the entire
contents of the learner will be erased)
4. The OK LED will illuminate, indicating that source’s function code has been erased
from memory in the Z•090.
To clear all the learned commands on a Source Page:
1. Press and hold the appropriate source select key on the Z•100.
2. While holding the source select key on the Z•100 (or TV key on the Z•150), press and
release CLEAR on the Z•090, then wait until the OK LED turns on. This indicates that
all learned codes for the selected source have been erased from the Z•090’s memory.
To clear a Learned Command From the System Page:
1. Press SYSTEM PAGE on the Z•090
2. On the Z•PAD, select the function key you want to erase
3. Press CLEAR on the Z•090. The OK LED will illuminate, indicating the system page
function has been reset to the ELAN default.
To clear All Learned System Page Commands:
1. Press and hold the SYSTEM PAGE button on the Z•090.
2. While holding the SYSTEM PAGE button, press and release CLEAR, then wait until the
OK LED comes on, indicating that all System Page codes have been reset to their
ELAN defaults.
To clear a macro string programmed to a keypad button:
1. Press the macro key on the keypad you want to clear
2. Press the MACRO button on the Z•090
3. Momentarily press the CLEAR button on the Z•090.
To edit a macro string, simply reprogram it!
Clearing the Entire Learned Contents of the Z•090 Programmer
1. Press and hold the CLEAR button on the Z•090 until the OK LED turns on
(approximately 3 seconds), indicating the Z•090’s memory has been erased.
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
Clearing the Entire Learned Contents of a Z•PAD
To clear the entire contents of a keypad you must load a “cleared” Z•090 memory map into
it. This is done by:
1. Clear the Z•090 first (see 1. above)
2. Press the LOAD button on the Z•090. This will load an empty Z•090 into the keypad,
erasing its memory content and restoring all ELAN factory defaults.
G. Downloading to the Z•100 Keypad
Once you have finished learning all of your source’s IR codes into the Z•090, you will need to
‘download’ this information each keypad.
Always press the
LOAD button on the
Z•090 before unplugging it from the 11VAC
power supply or the
AC wall outlet.
Pressing LOAD stores
all learned information
in the Z•090’s FLASH
MEMORY. Failure to
press LOAD before
powering down the
Z•090 will result in the
loss of all learned
information.
To download the contents of the Z•090’s memory into a keypad:
1. If a powered-up Z•090 is already connected to a Z•100 via the download cable, skip
to step 5.
2. Make sure that the Z•090 and the keypads are powered down.
3. Connect the download cable between the Z•090 and a Z•100 keypad.
4. Connect the 11 VAC power cube to the Z•090 and plug it into an outlet.
5. Press the LOAD button on the Z•090. During download, the BUSY LED will
illuminate, indicating data transfer is taking place between the Z•090 and the Z•100.
This process takes 3 to 5 seconds. When the download is complete, the BUSY LED
will turn off and the OK LED will turn on.
Pressing the LOAD button also loads the non-volatile flash memory of the Z•090, allowing
you to unplug the Z•090 from the 11 VAC adapter and move to another keypad for programming. You do not need to remove the keypad from the wall to download to it. However, power
to the Z•630, HDC2000 or Z•080 must be OFF in order to download the Z•090’s memory to
the individual keypads.
H. Uploading from a Z•PAD to the Z•090
(Software Version 011 or Higher)
Data stored in Z•100/Z•150keypads can be uploaded to the Z•090’s flash memory. This
feature allows you to “clone” the data from one keypad to another.
Uploading from a
Z•PAD will overwrite
the IR data in the
Z•090 Flash Memory.
NOTE:
Keypads programmed
with Version 007
Z•090 software do
not support this
upload routine and
will have to be
reprogrammed from
scratch.
How to Upload:
1. Make sure that the Z•090 and the keypad are unpowered.
2. Connect the download cable between the Z•090 and the Z•PAD.
3. Connect the 11VAC power cube to the Z•090 and plug it into an outlet.
4. Wait for the OK LED on the Z•090 to illuminate.
5. Press and hold the POWER key on the Z•100. (The Power LED will not illuminate)
6. While holding the POWER key, press the LOAD button on the Z•090 to initiate the
upload. The BUSY LED will wink momentarily, then the OK LED will illuminate,
indicating the upload data transfer is complete.
You can now make changes to the data and re-download to the Z•PAD, or you can unplug the
Z•090 and take it to another keypad for downloading.
I. Modifying a Programmed Z•PAD Memory
(Software Version 011 or Higher)
The flash memory in both the Z•090 and Z•PAD can only be programmed “in bulk”. Selected
changes to a Z•PAD code map must be made by first uploading from the Z•PAD to the
Z•090. If you download just one or two new functions to a Z•PAD, you will erase the balance
of the learned codes in its flash memory.
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 15
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
ADDENDUM 1
PC INTERFACE
The Z•090 is equipped with a RS232 port than enables you to connect it to any IBM-compatible
PC or laptop computer.
PC TOOLS
The PC Tools diskette enclosed with your Z•090 is a DOS-based software package that allows you
to build, store and access IR Code and Client files.
J. Connecting the Z•090 to Your Computer
With both the Z•090 and your computer powered up, connect the Z•090 to an unused COM
PORT on your computer using the RS232 Interface Cable prodiced (see diagram below).
K. Computer Settings
These software tools have been designed to work with IBM compatible P.C.s running in an
MS-DOS operating system environment.
For error free results in uploading and downloading data from a Z•090, your P.C. should not be
running WINDOWS. (Including clicking on the DOS prompt while in WINDOWS.) Running in a
straight DOS environment will eliminate any conflicts caused by WINDOWS handling of serial port
communications.
Page 16
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
To put your PC in a non-WINDOWS operation mode:
• Click on Start, Click on Shut Down, then select:
• Restart the computer in MS-DOS mode. (In WINDOWS 3.1 CLOSE windows)
• You will then see C:\WINDOWS> on the screen. Insert the Z•090 Keypad
Programming Archive Software Disc into the A drive of your computer.
• Then type A:ENTER, and you will see A:\> prompt on the screen.
• Next connect the RS-232 interface cable supplied with the Z•090 to either COM1 or
COM2 port on the back of your computer. A keypad can be connected to the Z•090
while in this configuration, but it is not necessary in order to use these tools.
• Power up the Z•090 and you are now ready to go!
• When you are finished using these tools, typing “Exit” will restart the WINDOWS
program (3.1, 95 or 98) on your machine. (In WINDOWS 3.1 type WIN and then hit
return.)
NOTE: Do not leave to RS-232 cable unconnected to a computer but connected to the back
of a Z•090 while learning. The un-terminated cable may disrupt the learning function of the
Z•090.
L.
PC Tools
Defined below are the PC tools used to download and upload IR code files to and from the Z•090
Keypad Programming Module. Also described are the manipulation tools required to extract, build
and view client specific and IR library code sets. The file structures used in these utilities come in
two forms––MAP files and LIB files. A MAP file contains all the IR data on all the source pages
uploaded from the RAM memory of a Z•090. A LIB file contains the extracted IR data associated
with a specific remote learned on ONE source page in a MAP file.
Included on the floppy disc are the following software tools:
ZUPLOAD.EXE
Uploads the RAM memory contents of a Z•090 to a MAP file on your P.C.
ZDNLOAD.EXE
Downloads a MAP file on your P.C. to the RAM and flash memory of
a Z•090
ZEXTRACT.EXE
Extracts the IR codes from one source page of a MAP file, and writes
the data to a LIB file.
ZMERGE.EXE
Merges a LIB file into one source page of a MAP file.
DATAVIEW.EXE
Converts a MAP or LIB file into a viewable format and writes the data
to a text file.
MAPVIEW.BAT
Runs DATAVIEW on a MAP file and opens the text editor on your
computer to view the newly created TXT file.
LIBVIEW.BAT
Runs DATAVIEW on a LIB file and opens the text editor on your
computer to view the newly created TXT file.
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 17
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
Also included on the disc is some test library and map files for you to try out the viewer programs with.
ZUPLOAD.EXE
Syntax:
ZUPLOAD MAPFILE [COM1 or COM2]
Where MAPFILE is the complete DOS name (8 characters max) of the MAP file to which the IR
code data is to be written, and [COM1 or COM2] is the optional directive for the COM port to
be used for the RS-232 interface connection. (COM1 is the default and can be omitted from
the command line if used). The serial link should be connected and the Z•090 should be powered up before this utility is executed.
EXAMPLE:
ZUPLOAD SMITH
Will upload data from the Z•090 into a file named “SMITH.MAP” via the
COM1 port.
ZUPLOAD JONES.MAP COM2
Will upload data from the Z•090 into a file named “JONES.MAP” via the
COM2 port. (the .MAP extension does not need to be entered, but it is OK if
you do)
ZDNLOAD.EXE
Syntax:
ZDNLOAD MAPFILE [COM1 or COM2]
Where MAPFILE is the complete DOS name (8 characters max) of an existing MAP file, and
[COM1 or COM2] is the optional directive for the COM port to be used for the RS-232 interface connection. (COM1 is the default and can be omitted from the command line if used).
The serial link should be connected and the Zª090 should be powered up before this utility is
executed.
EXAMPLE:
ZDNLOAD SMITH.MAP
Will download PC data from the file named “SMITH.MAP” to the Z•090 via
the COM1 port. (.MAP does not need to be entered, ZDNLOAD SMITH works
too)
ZDNLOAD JONES COM2
Will download PC data from the file named “JONES.MAP” to the Z•090 via
the COM2 port.
ZEXTRACT.EXE
Syntax:
ZEXTRACT MAPFILE Sx LIBFILE
Where MAPFILE and LIBFILE are the complete DOS file names of the MAP file to be read and
the LIB file to be created from the source page Sx of the MAP file, where Sx is as follows :
S0 = System Page
S5 = DVD Page
S10 = , VCR Page
S1 = Tuner Page
S6 = DSS Page
S11 =
, DVD Page
S2 = CD Page
S7 =
, Tuner Page
S12 =
, DSS Page
S3 = Tape Page
S8 =
, CD Page
S13 = TV Page
S4 = VCR Page
S9 =
, TAPE Page
Page 18
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
EXAMPLE:
KEYPAD
PROGRAMMING MODULE
ZEXTRACT SMITH.MAP S2 YAMCD.LIB
Will Extract the IR data on the CD (S2) Page and create an IR library file
called YAMCD.LIB (Yamaha remote)
This could also be written in short form as:
“ZEXTRACT SMITH S2 YAMCD”
ZMERGE.EXE
Syntax:
ZMERGE MAPFILE Sx LIBFILE
Where MAPFILE and LIBFILE are the complete DOS file names of the MAP file to be merged,
with the data from the LIB file merged to the source page Sx of the MAP file, where Sx is as
follows:
S0 = System Page
S5 = DVD Page
S10 =
, VCR Page
S1 = Tuner Page
S6 = DSS Page
S11 =
, DVD Page
S2 = CD Page
S7 =
, Tuner Page
S12 =
, DSS Page
S3 = Tape Page
S8 =
, CD Page
S13 = TV Page
S4 = VCR Page
S9 =
, TAPE Page
EXAMPLE:
ZMERGE JONES.MAP S6 SONYABC.LIB
Will merge the IR data from the SONYABC LIB file onto the DSS (S6) Page in
the JONES MAP file
This could also be written in short form as:
“ZMERGE JONES S6 SONYABC”
DATAVIEW.EXE
Syntax:
DATAVIEW INFILE TXTFILE
Where INFILE is the complete DOS file name of either a MAP or LIB file, and TXTFILE is the
complete DOS file name of a viewable text file to be created. This utility creates a listing of
the contents of a MAP or LIB file in plain English. This data viewer is used in the MAPVIEW
and LIBVIEW batch file programs defined below, and not normally run by itself.
EXAMPLE:
DATAVIEW SMITH.MAP SMITH.TXT
Will create a word processor or text editor viewable SMITH.TXT file. To view
this text file, you would need to run your DOS text editor.
(i.e. a:\>EDIT SMITH.TXT)
MAPVIEW.BAT
Syntax:
MAPVIEW MAPFILEROOT
Where MAPFILEROOT is the root only (no .MAP extension) of a MAP file to be viewed.
For example:
MAPVIEW SMITH will launch the following command lines:
DATAVIEW SMITH.MAP SMITH.TXT
EDIT SMITH.TXT
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 19
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
This example will convert SMITH.MAP to a viewable format, write the text to SMITH.TXT, and
open SMITH.TXT in an editor.
If needed, this batch file can be edited to select a different text editor.
To exit the text editor, press ALT F and the ALT X.
LIBVIEW.BAT
Syntax:
LIBVIEW LIBFILEROOT
This batch file is identical to MAPVIEW.BAT except that it operates on a LIB file to create a
viewable text file. Only one source page is present in the library files.
For example:
LIBVIEW YAMCD will launch the following command lines:
DATAVIEW YAMCD.LIB YAMCD.TXT
EDIT YAMCD.TXT
This example will convert YAMCD.LIB to a viewable format, write the text to YAMCD.TXT, and
open YAMCD.TXT in an editor.
Viewable (and somewhat meaningful) data included in these text files are:
• Device Descriptors, which show the common carrier attributes of a particular remote
• System Page Learned IR Commands, showing what system page keys have IR data
behind them.
NOTE: Learned source select keys (in stand alone receiver based applications)
are always on the system page. You should learn all the stand alone receiver
remote control commands onto the system page of the Z-090 for uploading
and storage.
•
Programmed Global Macros are shown next, including
,7
,8
,9
,Party
, FAV, and PARTY. Also included are the actual (to the mSec) programmed delay
and gap lengths of each step in the macro.
• Source Page Function Keys–– for each of the possible 13 sources, all programmed
keys will show their hex code data.
•
Macros programmed to each Source Select and FAV buttons are stored on the source
pages they are associated with, and show at the bottom of each source page listing.
•
Extended key code - data associated with remote controls that have greater than 16
bit key codes will be displayed here.
Once you have finished looking at the data in these files press Alt F, then Alt X to pop up the
text editor control panel and exit the program. These newly created text files will remain in the
directory with your library and map files, and can be deleted at any time with no adverse
effect to the original MAP files they were created from.
Page 20
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
M. MS-DOS Commands
A couple of MS-DOS commands which come in handy while operating in the DOS environment are:
A:\>DIR/W
Will list all the files on the A drive in a row format
A:\>COPY JONES.MAP C:\Z090 Will copy the JONES.MAP file from the A drive to your C
drive, into the Z•090 directory. (You must create the Z•090
directory first)
A:\>COPY *.MAP C:\Z090
Will copy all the MAP files from the A drive to your C
drive, into the Z•090 directory. (You must create the Z•090
directory first)
A:\>COPY *.LIB C:\Z090
Will copy all the LIB files from the A drive to your C drive,
into the Z•090 directory.
A:\>DEL *.TXT
Will delete all the TXT files on the A drive. (Be careful with
this one)
Also, directory paths can be inserted into all executable command lines. When no path is
specified, the program defaults to the current directory. For example:
• ZUPLOAD C:\ZTOOLS\MAP\SMITH would upload a SMITH.MAP file into the
C:\ZTOOLS\MAP directory.
• ZDNLOAD C:\ZTOOLS\MAP\JONES would download the JONES.MAP file from the
C:\ZTOOLS\MAP directory into a Z-090.
• ZEXTRACT A:\JONES S1 C:\ZTOOLS\LIB\SONYABC would extract the tuner page (S1)
from the Jones file on the A drive and create a SONYABC LIB file and place it in the
C:\ZTOOLS\LIB directory.
• ZMERGE A:\JONES S6 C:\ZTOOLS\LIB\YAM123 would take the YAM123.LIB file in
the C:\ZTOOLS\LIB directory and place it on the DSS (S6) page in the JONES.MAP file
located on the A drive.
N. Summary
We are working on a WINDOWS based version of this program; but in the meantime, these
tools are ready now, will save you lots of time, and are easy to use.
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 21
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
FACTORY DEFAULT KEY FUNCTIONS
Page 22
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
SYSTEM PAGE COMMANDS
Z•PAD
Keypress
Command
SHADED AREAS
REPRESENT
DEFAULT
COMMANDS
RECOGNIZED BY
THE Z•630
OR SERIES HD™
MCU
TNR
CD
TAPE
VCR
DVD
DSS
, TNR
, CD
, TAPE
, VCR
, DVD
, DSS
TV
VOL UP
VOL DN
PLAY
STOP
CNTRL+
CNTRLFAV
DISK
MUTE
POWER
1
2
3
4
5
6
7
8
9
0
ENT
RCL
FM/AM
PARTY
, VOL UP
, VOL DN
, PLAY
, STOP
, CNRL+
, CNTRL , FAV
, DISK +
, MUTE
, POWER
,1
,2
,3
,4
,5
,6
,7
,8
,9
,0
, ENT
, RCL
, FM/AM
, PARTY
, TV
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Z•630 Preamp
Default Function
Command
TNR SOURCE SELECT
CD SOURCE SELECT
TAPE SOURCE SELECT
VCR SOURCE SELECT
DVD SOURCE SELECT
DSS SOURCE SELECT
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO DEFAULT CODE SENT
VOL UP
VOL DN
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
MUTE
POWER
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
WHM+
WHMNO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
DND TOG
NO Z• RESPONSE
BASS+
TREB+
LOUD
BASSTREBSPAT TOG
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
FLAT EQ
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
NO Z• RESPONSE
KEYPAD SHIFT/
NOT LEARNABLE
© ELAN Home Systems • 1998 • All rights reserved. 9/98
MCU 3760 Eprom
Default Function
TNR SOURCE SELECT
CD SOURCE SELECT
TAPE SOURCE SELECT
VCR SOURCE SELECT
DVD SOURCE SELECT
DSS SOURCE SELECT
MCU AUX 1 SOURCE SELECT
MCU AUX 2 SOURCE SELECT
MCU AUX 3 SOURCE SELECT
MCU AUX 4 SOURCE SELECT
NO MCU RESPONSE
NO MCU RESPONSE
NO DEFAULT CODE SENT
VOL UP
VOL DN
PLAY
STOP
SKIP+
SKIP, ELAN SOURCE MACRO
, DISK+
MUTE
ELAN
1
2
3
4
5
6
7
8
9
0
ENTER
RECALL
, FM
,5
ON–H
OFF–H
PAUSE
REWIND
FF
REVERSE
,4
, DISCDND
POWER
BASS+
TREB+
NO MCU RESPONSE
BASSTREBNO MCU RESPONSE
,7
,8
,9
ON–F
, RANDOM
, REPEAT
, AM
,6
*
A/B
KEYPAD SHIFT/
NOT LEARNABLE
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Stand-Alone
Learnable
Function
TNR SOURCE SELECT
CD SOURCE SELECT
TAPE SOURCE SELECT
VCR SOURCE SELECT
DVD SOURCE SELECT
DSS SOURCE SELECT
, TNR SOURCE SELECT
, CD SOURCE SELECT
, TAPE SOURCE SELECT
, VCR SOURCE SELECT
, DVD SOURCE SELECT
, DSS SOURCE SELECT
TV SOURCE SELECT
RECEIVER VOL UP
RECEIVER VOL DN
PLAY
STOP
CNTRL+
CNTRLFAV
DISK+
RECEIVER MUTE
RECEIVER POWER
1
2
3
4
5
6
7
8
9
0
ENT
RCL
FM/AM
PARTY
, VOL UP
, VOL DN
, PLAY
, STOP
, CNTRL+
, CNTRL, FAV
, DISK, MUTE
, POWER
,1
,2
,3
,4
,5
,6
,7
,8
,9
,0
, ENT
, RCL
, AM/FM
.6
, TV
KEYPAD SHIFT/
NOT LEARNABLE
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Page 23
ELAN
HOME
You May Fill Out the Following
Three Pages on your Computer.
Then Print the Pages.
SYSTEMS
KEYPAD
PROGRAMMING MODULE
LEARNED COMMANDS PLACEMENT MAP
Z•630 Source #: ____________ Z•630 Source Name:_______________________ PC File Name:_____________
Source Manufacturer:____________________________ Source Model #:___________ Remote Model #________
Will the map below apply to all keypads in the system?
Source
Select
Button
Learned to
Factory Default
Z•100/Z•150
Key
TNR
CD
TAPE
VCR
DVD
DSS
TV
VOL UP
VOL DN
PLAY
STOP
CNTL UP
CNTL DN
FAV
DISC
MUTE
POWER
1
2
3
4
5
6
7
8
9
0
ENT
RCL
FM/AM
PARTY
, VOL UP
, VOL DN
, PLAY
, STOP
CNTL UP
, CNTL DN
, FAV
, DISC
, MUTE
, POWER
,1
,2
,3
,4
,5
,6
,7
,8
,9
,0
, ENT
, RCL
, FM/AM
, PARTY
,TV
Learned to
Customized
Z•100/Z•150
Keycap
❏ YES ❏
NO If NO, keypad location:_____________
Z•630
Factory Default
System Function
New Learned Command
SELECT TUNER
SELECT CD
SELECT TAPE
SELECT VCR
SELECT DVD
SELECT DSS
SELECT TV
VOL UP
VOL DN
SOURCE MACRO
N/A
N/A
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
© ELAN Home Systems • 1998 • All rights reserved.
MUTE
ZONE ON/OFF
GLOBAL MACRO
WHM ON
WHM OFF
,
,
,
,
,
,
,
,
N/A
N/A
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
GLOBAL MACRO
DND ON/OFF
BASS +
TREBLE +
LOUDNESS ON/OFF
BASS TREBLE ENHANCE ON/OFF
GLOBAL MACRO
GLOBAL MACRO
GLOBAL MACRO
EQ FLAT
Z•630 FEATURE ONLY
Z•630 FEATURE ONLY
Z•630 FEATURE ONLY
GLOBAL MACRO
ANTENNA A/B
9/98
Page 24
INSTALLER:___________________________________ PC FILENAME:______________________________
SOURCE SELECT MACROS
TNR MAC
KEY
L/G
STEP 2
KEY
L/G
STEP 3
KEY
L/G
STEP 4
KEY
L/G
STEP 5
KEY
L/G
STEP 6
KEY
VCR MAC
DVD MAC
DSS MAC
LOCAL TV
MACRO
SYSTEMS
STEP 1
CD MAC TAPE MAC
FAVORITE OR GLOBAL MACROS
HOME
L=TRANSMISSION LENGTH
G=DELAY GAP
ELAN
JOB #____________
CLIENT MACRO PAGE
© ELAN Home Systems • 1998 • All rights reserved. 9/98
DATE:________________________ CUSTOMER NAME:______________________
L/G
STEP 7
KEY
L/G
STEP 8
KEY
L/G
STEP 9
KEY
L/G
STEP 10
KEY
L/G
STEP 11
KEY
L/G
STEP 12
KEY
STEP 13
KEY
L/G
NOTES:
Page 25
KEYPAD
PROGRAMMING MODULE
L/G
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
CLIENT SOURCE MEMORY MAP
Client Name:_______________________________ Installer:______________________________
Job #:____________________________________
Client PC File Name:____________________
Date:_____________________________________
Keypad Location:_______________________
Z•PAD SOURCE
MEMORY
SOURCE MFG/MODEL #
REMOTE MODEL #
REMOTE PC
FILE NAME
CD
TAPE
VCR
DVD
DSS
*, TNR
*, CD
*, TAPE
*, DVD
*, DSS
TV
NOTES:
Page 26
© ELAN Home Systems • 1998 • All rights reserved. 9/98
ELAN
HOME
SYSTEMS
KEYPAD
PROGRAMMING MODULE
KEYPAD
PROGRAMMING
MODULE
Limited Warranty
ELAN HOME SYSTEMS, L.L.C. (“ELAN”) warrants the Z•090 Programming Module manufactured by it to be free from defects in
materials and workmanship for two (2) years from the date of purchase. If within the applicable warranty period above purchaser
discovers such item was not as warranted above and promptly notifies ELAN in writing, ELAN shall repair or replace the items at the
company’s option. This warranty shall not apply (a) to equipment not manufactured by ELAN, (b) to equipment found to have been
installed by other than an authorized ELAN installer, (c) to installed equipment which is not installed to ELAN’s specifications, (d) to
equipment found to have been repaired or altered by others than ELAN, (e) to equipment found to have been subjected to
negligence, accident, or damage by circumstances beyond ELAN’s control, including, but not limited to, lightning, flood, electrical
surge, tornado, earthquake, or any other catastrophic events, or to improper operation, maintenance or storage, or to other than
normal use of service. With respect to equipment sold by, but not manufactured by ELAN, the warranty obligations of ELAN shall in
all respects conform and be limited to the warranty actually extended to ELAN by its supplier. The foregoing warranties do not cover
reimbursement for labor, transportation, removal, installation, or other expenses which may be incurred in connection with repair or
replacement.
Except as may be expressly provided and authorized in writing by ELAN, ELAN shall not be subject to any other obligations or
liabilities whatsoever with respect to equipment manufactured by ELAN or services rendered by ELAN.
Disclaimer: The ELAN Z•090 Learning System is an advanced design capable of accurately capturing and
duplicating most infrared command sequences used in today’s consumer electronics. However, ELAN in no way
represents, guarantees, or claims that the Z•090 will achieve 100% functionality with every manufacturer’s source
equipment. RF remote controls, very high frequency carrier based codes multiple imbedded codes or excessive
word lengths cannot be learned by this system. In this case, the homeowner will have to use the original remote
control that shipped with the source equipment.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES
EXCEPT WARRANTIES OF TITLE, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
ELAN “On-Site” Technical Support 1-800-622-ELAN (3526)
2428 Palumbo Drive • Lexington, KY 40509 • 1.606.269.7760 • FAX 1.606.269.7972
©1998 ELAN Home Systems, LLC. ELAN, ELAN Home Systems, Z•090, Z•100, Z•150, Z•PAD, Series HD™ are registered trademarks of
ELAN Home Systems, 2428 Palumbo Drive, Lexington, KY 40509. Elan reserves the right to change product specifications without notice.
© ELAN Home Systems • 1998 • All rights reserved. 9/98
Page 27
ELAN HOME SYSTEMS
ADDENDUM 2
090
WINTOOLS TM
Z WINTOOLS is the new Windows-based archiving software program for the Z Series Z 090 Keypad
Programming Module.
With Z WINTOOLS all of the keypad and macro programming for every Z system you install can be saved as
individual Client Files, enabling you to reference every source component, IR command and macro that has been
programmed for any given project. It also makes it easy to update keypads when new source components have
been added to the system.
From the Client Files you can create your own custom IR Library files. Every source remote control that has
been 'learned' into the Z 090 and then saved in a Client File can be given an individual IR Library file name and
used again and again for subsequent installations.
And now it's all just point-and-click.
INSTALLING Z WINTOOLS
Z WINTOOLS is included with every Z 090 Keypad Programming Module ordered after 2/21/00, or can be
downloaded from the ELAN web site (www.elanhomesystems.com). Windows '95 or higher will be required.
To install Z WINTOOLS, click on SETUP.EXE from your Start/Run menu or from Windows Explorer and follow the
Installation Wizard prompts. Unless directed otherwise, Z WINTOOLS will automatically be installed in your
C:Program Files directory under ELAN Home Systems/ZTOOLS.
CONNECTING THE Z 090 TO YOUR COMPUTER
Before you open Z WINTOOLS, use the provided RS232 Interface Cable to connect
the Z 090 to an unused COM port on your computer.
GETTING STARTED
When you open Z WINTOOLS there will be a STATUS
dialog box at the bottom left corner of the screen that
will indicate whether communication has been
established between the Z 090 and your computer.
If the connection has not been confirmed, check that
the cable is connected properly and that your COM port
is active. You may also try rebooting Z WINTOOLS
and/or your computer.
Once the connection has been confirmed the STATUS box
will also tell you what version of Firmware resides in your Z 090.
DEFINITION OF OPERATION BUTTONS
O
P
E
R
A
T
I
O
N
B
U
T
T
O
N
S
UPLOAD TO PC
Uploads learned IR commands and Macros from the Z 090
DOWNLOAD TO Z090
Downloads saved Client files from the PC to the Z 090
OPEN CLIENT FILE
Opens saved Client files
SAVE CLIENT FILE
Saves uploaded Z 090 information as a Client file
EXTRACT IR PAGE
Extracts the learned IR commands from a Client file source page
and allows them to be saved as an IR Library file
MERGE IR FILE
Merges an IR Library file onto a specific source page in a Client file
OPEN IR LIBRARY
Allows you to view a previously saved IR Library file
NEW
Begin a new Client file
STATUS Box
c
ELAN Home Systems, 2/00
Z 090 ADDENUM 2
Page 1
ELAN HOME SYSTEMS
ADDENDUM 2
090
WINTOOLS TM
UPLOADING FROM THE Z 090
Once you have learned all your IR commands, programmed all your macros, and loaded both into the Z 090
(as detailed in the Z 090 Installation Manual), all this information can be uploaded and viewed by clicking on
UPLOAD to PC.
INFORMATION DISPLAYED
After UPLOAD is complete you will be able to view all the programmed data. From top to bottom, the viewable
data is as follows:
SYSTEM PAGE
Includes all data that was learned on the Z 090's System Page, as well as any Global Macros that were
programmed.
SOURCE PAGES (13 - one for each learnable source)
Each Source Page displays every Z PAD key that has an IR command learned under it. (i.e. in the display
page below, TUNER has valid IR commands learned under Z PAD keys CONTROL UP, CONTROL DOWN,
1, 2, 3, 4 & 5)
If a SOURCE SELECT macro has been programmed, it will be displayed next (Macro TNR SELECT).
If a FAVorite macro has been programmed, it will appear beneath the Source Select macro (Macro TNR FAV)
SAVING THE FILE
To save the file you have just uploaded form the Z 090, click on SAVE CLIENT FILE, give the file a name and
click on SAVE. The file will automatically be saved into the Client File folder (see above).
Page 2
Z 090 ADDENUM 2
c
ELAN Home Systems, 2/00
ELAN HOME SYSTEMS
090
ADDENDUM 2
WINTOOLS TM
CREATING IR LIBRARIES
Once you have saved a Z 090 program as a Client File, you can now create a custom IR Library file for each of
the source remotes that you have learned. Once created, IR Library files can be used to create new Client files
where the same source component and IR commands are being used.
EXTRACT IR PAGE
To create an IR Library file:
1. Click on EXTRACT IR PAGE. The name of each source page that has IR commands learned under it will
appear.
2. Double click on the source page that you wish to extract (i.e. Tuner Page).
3. Give the file a name (Use an easily recognizable name, such as one that reflects the source's manufacturer
and model number).
4. Click on SAVE.. The file will automatically be saved in the IR Library folder.
NOTE: Macros are not extracted and saved to IR Library files.
Extract IR Page
OPEN IR LIBRARY
Clicking on OPEN IR LIBRARY brings up a list of all your IR Library files. Then, clicking on OPEN (or double
clicking on an IR Library file name) will open the file and allow you to view the learned Z PAD keys in that file.
c
ELAN Home Systems, 2/00
Z 090 ADDENUM 2
Page 3
ELAN HOME SYSTEMS
ADDENDUM 2
090
WINTOOLS TM
MERGING IR FILES
An IR Library file can be placed or 'merged' into new or existing Client Files.
CREATING A NEW CLIENT FILE
To create a new Client file from the IR Library:
1. Click on NEW
2. Click on MERGE IR FILE. A list of all your IR Library files will appear
3. Select the IR Library file you wish to place in your new client file, then click OPEN.
4. A list of all the source pages will appear. Double click on the source page you wish to 'merge' the IR Library
file to.
5. Your new Client file is displayed showing the Source Page and the IR commands you just merged onto it.
6. Repeat 1-4 to add additional IR Library files to your new Client file.
STEPS 2 & 3
STEP 5
STEP 4
Page 4
Z 090 ADDENUM 2
c
ELAN Home Systems, 2/00
ELAN HOME SYSTEMS
ADDENDUM 2
090
WINTOOLS TM
MERGING IR LIBRARY FILES TO AN EXISITING CLIENT FILE
To add or change IR Library files in an existing Client file:
1. Click on OPEN CLIENT FILE and select the Client file you wish to modify
2. Click on MERGE IR FILE. Your IR Library file folder will open. Select the IR Library file that you wish to merge
onto your Client file, the click OPEN (or double click on the IR Library file name).
3. Select the source page you wish to merge the IR Library file to and double click.
NOTE: Merging a IR Library file onto a source page will overwrite any existing data on that page.
4. Repeat steps 2 & 3 to add additional IR Library files to the Client file. Save the Client file when finished
STEPS 1 & 2
STEP 3
DOWNLOAD TO Z090
Once you have finished creating or modifying a Client file, click on DOWNLOAD TO Z090 to 'dump' the new
program into the Z 090's flash memory. The Z 090 can now be unplugged and taken out to the job site where
the new program can be downloaded into the system's Z PADs.
c
ELAN Home Systems, 2/00
Z 090 ADDENUM 2
Part # 40615-138-08
Page 5