DATA SHEET
Insulation Components 24, 80, 140 Polyiso iShields
iso
Po
ly
80
,1
40
24
,
Insulation Components 24, 80, 140 Polyiso iShields meet a
broad range of pipe support applications on low and mid
temperature lines. They provide a continuous section of
insulation and vapor barrier and are designed for pipe
systems operating between –297° F and 300° F. The
insulation and vapor barrier extend beyond the galvanized
steel shield for a vapor-tight joint with the adjoining
insulation. Insulation Components 24, 80, 140 Polyiso
iShields are suitable for use in any type of clamp as well as
in band-type hangers. (Also available with a 360° iShield)
High-compressive strength polyisocyanurate inserts and
heavy gauge steel iShields ensure proper pipe support.
These cost affective and time saving designs meet the
requirements of all specified insulated pipe hanger systems.
iSh
ield
s
Product Features
Installation
For indoor use on plumbing, heating, chilled
water and refrigeration piping from -297º to
300º F. Install at hanger locations on cold
or hot piping systems.
Product Detail
Physical Property
Recommended Pipe Size
Compressive Strength
K-Factor, Btu•in/hr•ft²•°F
Aged 180 days @ 75°F
Service Temperature, °F
Compressive Strength, lb/in²
Parallel to rise-thickness
Perpendicular to rise-width
Perpendicular to rise-length
Water Absorption, 24-hr immersion
% by volume
Water Vapor Permeability (perm-inch)
Closed Cell Content, %,min
Surface Burning Characteristics
Flame Spread/Smoke Developed (FS/SD)
Vapor Retarder Film
Thickness Average
Perm Rating
24
80
½”- 1-1/2” IPS
24 PSI
4”- 6” IPS
80 PSI
8”- 24” IPS
140 PSI
.19
-297 to +300
.19
-297 to +300
.20
-297 to +300
650
475
600
2,100
1,800
2,600
3,100
2,800
2,800
<0.7
<0.7
2.9
2.9
95
95
25/450 up to 6” 25/450 up to 6”
thickness
thickness
6 mil.
.01
6 mil.
.01
140
Specification Compliance
ASTM D-1621, 1622, 1623
ASTM C-518
ASTM D-1621
<0.7
2.9
95
25/450 up to 6”
thickness
ASTM C-272
ASTM E-96
ASTM D-2856
6 mil.
.01
ASTM D-624
ASTM E-96
ASTM E-84
Insulation Size / iShield Size
Nominal Pipe Size Compressive Strength
Insulation Length
iShield Length
iShield Gauge
1/2” - 1-1/2”
24 PSI
6”
4”
20 Ga.
2”- 4”
80 PSI
6”
4”
18 Ga.
5”- 6”
80 PSI
9”
6”
16 Ga.
9”
6”
8”
140 PSI
16 Ga.
10”- 24”
140 PSI
12”
10”
14 Ga.
Unless otherwise indicated, data shown are typical values obtained from representative production samples by the material manufacturer. This data
may be used as a guide for design purposes but should not be construed as specifications. This information is furnished without warranty, expressed
or implied, except that it is accurate to the best knowledge of Insulation Components, Inc. Insulation Components, Inc assumes no legal responsibility
for use or reliance upon this data. For information regarding specific applications of the product please contact Insulation Components, Inc.
13301 Chippewa Blvd., Mishawaka, IN 46545
Bus: 574.258.1885 TF: 866.713.7476 TF Fax: 866.565.0359
www.insulationcomponents.com
RM 5-22-2014 Polyiso Data