Writing the Lab Abstract

CHEMISTRY 221-223 LABORATORY REPORTS
In addition to the prelab, data, calculations, graphs and questions on the laboratory handouts,
each lab report must include a typed abstract. All students must write their own unique abstracts!
An abstract is a short summary of the experiment (usually 100-400 words). It should include the
scientific heart of the experiment and the necessary details. The trick to writing a good abstract is
to describe the essence of the experiment and to include just enough detail for a fellow scientist
to follow it. One format to follow could be: one sentence to put the experiment in context,
followed by a short description of what you did, what you observed/measured and the key
science concepts involved. If you collected quantitative data, include a summary of the data and
an error analysis. Sketches are good to include, too!
Two sample abstracts are included below. They are written about labs that you will not perform,
but they should give you a good idea of what an abstract should look like. Note that the lab with
quantitative data includes a succinct error analysis.
ABSTRACT (Qualitative Data – no error analysis required) – SOLUBILITY AND POLARITY
We performed an experiment to determine the relative solubilities of different liquids
with each other. We tested the following seven liquids in all combinations: water, carbon
tetrachloride, oleic acid, vegetable oil, glycerol, ethanol and carbon disulfide. We added 2 mL of
one liquid to a test tube, then added 2 mL of another liquid, shook/stirred the contents of the test
tube and waited to see if one layer formed or two. We found that the water and glycerol formed a
single layer with each other and with ethanol. The carbon tetrachloride, oleic acid, vegetable oil
and carbon disulfide formed a single layer with each other and with ethanol. All other
combinations eventually separated into two distinct layers. Ethanol was the only liquid that
formed a single layer with all of the other liquids. Our observations are consistent with the
solubility rule: “like dissolves like”. Water and glycerol are both very polar molecules, due to
polar OH groups and short (if any) carbon chains. Oleic acid and vegetable oil are nonpolar, with
some polar groups but much longer carbon chains. Carbon tetrachloride and carbon disulfide are
nonpolar by virtue of their symmetrical shapes (and small electronegativity differences). Ethanol
is an intermediate molecule with a single polar OH group on a two-carbon chain. It bridges the
gap between polar and nonpolar molecules and dissolves wide variety of substances.
H2O
layer
CCl4
layer
polar & nonpolar
don't mix
H2O &
glycerol
in a
single
layer
CS2 &
CCl4
in a
single
layer
polar & polar
do mix
nonpolar & nonpolar
do mix
ABSTRACT (Quantitative Data – must include an error analysis) – Molecular Weight of a
Volatile Liquid
In this lab, we found the molecular weight of acetone from its vapor density. We added
several mL of acetone to a clean, dry Erlenmeyer flask of known mass, then covered the opening
with a piece of aluminum foil and poked a small hole in the center of the foil. We clamped the
flask into position in a water bath on a hot plate under a fume hood and monitored the
temperature of the water bath as the acetone started to evaporate. When the acetone had
completely evaporated, we noted the temperature, removed the flask from the water bath and
allowed it to cool to room temperature. During the cooling process, the acetone vapors in the
flask condensed and formed liquid acetone again. We determined the mass of liquid acetone, and
we knew this was the same mass of acetone vapor that had completely filled the flask at the
temperature we recorded. We reasoned that the pressure of the acetone vapor was the same as the
barometric pressure since the system was open to the atmosphere during heating. Finally, we
cleaned the flask, filled it to the top with water and poured the water into a graduated cylinder to
determine the precise interior volume of the flask. Then we calculated the molecular weight of
acetone from the equation: MW = dRT/P. After three trials, our average molecular weight was
60.1 g/mol with a standard deviation of 1.2 g/mol. Since the actual molecular weight of acetone
is 58.08 g/mol, this corresponds to a 3.4% error. I believe that our major sources of error were
caused by tiny droplets of liquid acetone still present in the flask when we thought it was entirely
full of vapor and the temperature of the inside of the flask being slightly lower than the
temperature of the water bath. Both of these sources of error would lead to a calculated
molecular weight that is higher than expected, which is what we observed.
As the flask was heated, the acetone evaporated.
This pushed all of the air (and some of the acetone)
out of the flask. The number of acetone molecules
remaining was determined by the temperature.