®
CHOOSING THE RIGHT FLOOR
KEITH® WALKING FLOOR® systems are available in a wide range of profiles and thicknesses to address the vast number of
applications that are in use worldwide. A general description of uses, applications, and benefits to each system is below.
- Heavy abrasion applications
(Steel Slat only)
- Full length bearing strip
- Leak resistant
- No floor seal
- Aluminum V-9 Slat typically
used for MSW, recyclables, and
light C&D
- Steel V-9 Slat designed for use
in heavy C&D, scrap metal,
aggregate, and asphalt
V-18 SERIES
2651
2654
- Original WALKING FLOOR®
slat profile
- Wide range of profile types
- Interchangeable slat
designs
V-9 SERIES
STEEL
ALUMINUM
5661701
2531
- Full length hold-down
- Full length bearing strip
- Leak resistant
- No floor seal
2692
- Used for MSW, biomass, light to
moderate C&D
-Available in thicknesses ranging
from 3/8” to 1/2” triple ridge
(Note: Steel wear strip needed when hauling highly abrasive materials.)
- Used for shredded paper, MSW,
recyclables, biofuels, and light to
moderate C&D, wood forest products
-Available in thicknesses ranging
from 1/8” to 3/4” triple ridge
STANDARD/IMPACT™
2185
2295
2299
PRESSURE SEAL®
- Light weight
- No floor seal
- Full length bearing
- Full length hold-down
2236
2195
- Used for agricultural, commodity,
biomass, and mulch
-Available in thicknesses ranging from
1/8” to 1/4”
2632
LEAKPROOF (LPIII)
- Designed for high moisture
loads.
- Can hold 12” of standing water
- Front mount drive
- Full length bearing strip
- Full length hold-down
- Used for MSW, medical waste
and silage
2145
REVISED 12.18.12
MOBILE APPLICATIONS
COMMON FLOORING AND COMPONENTS
STANDARD 3.5” SLATS
(3/16")
(7/32")
2185
2188
2190
BEARINGS
(1/4")
UHMW
(3/8")
(1/2" IMPACT™)
(1/2" CWS IMPACT™)
2558
2199
2295
2299
(3/4" IMPACT™)
(3/4" CWS IMPACT™)
2297
SUBDECK
SEAL
2301
3" WIDE
"T" BLOCK
WEARPAD
HOLD-DOWN
300301 BEARING
SPLASH GUARD
HOLD-DOWN
300308 BEARING
BENT "Y"
SPLASH GUARD
HOLD-DOWN
1"x1"
STEEL
1"x1"
ALUMINUM
47674
42045
3004
300301
2468
3003
1212
2469
3002
2281
PRESSURE SEAL®
ALUM TRAILER WALL
(1/8")
2235
(Not supplied
by KEITH®)
(1/8")
(1/8")
(3/16")
2193
2236
2195
HOLD-DOWN*
36928
(1/4")
LEAK PROOF (15 SLAT)
2375
2632
SUB-DECK
WINGED "T" BLOCK**
2234
37804
(19/32")
ALUM TRAILER WALL
* HOLD DOWN
ATTACHED TO EVERY
THIRD CROSS MEMBER
BRG STRIP
BRG STRIP
** WINGED “T” BLOCK
ONLY AT DISCHARGE
END OF EVERY SLAT
SUB-DECK
2207
LP BEARING
2145
2146
J - BEARING
SUB-DECK INSERT
2652
2670
1/2"
CWS IMPACT™
1/2"
IMPACT™
3/8"
FLAT TOP
1" ALUM or STEEL
8
SIDE SEAL
2654
2651
2692
WELD DOWN
WELD DOWN
BOLT DOWN
BOLT DOWN
2653
2650
2669
2672
UHMW
END PLUG (SOLID)
**SHOWN ON 5 1/4” CENTERS
**ALSO AVAILABLE ON 5” CENTERS
OPTIONAL STEEL WEAR STRIP
ALUM TRAILER WALL
V-9 SERIES
1" ALUM SIDE SEAL
4
V-PAN (ST)
2493
2460
5/8"
ALUMINUM
3/8"
FLAT TOP
ALUMINUM
2531
STEEL
5/32” 5661701
2631
BOLT DOWN
BOLT DOWN
2502
2491
**SHOWN ON 10 1/2” CENTERS **
ALSO AVAILABLE ON 10” CENTERS
1"
8 STEEL SIDE SEAL
STANDARD J-BEARING
1/8" 5661702
BOLT DOWN
WELD DOWN
2492
2490
J-BEARING PROTECTION (AL.)
SUB-DECK INSERT (AL.)
2528
2529
BOLT DOWN
WELD DOWN
UHMW
HIGH TEMP. INSERT
HIGH TEMP.
J - BEARING
2711
2527
2698
2446
®
www.keithwalkingfloor.com
STEEL TRAILER WALL
1" ALUM SIDE SEAL
4
STEEL TRAILER WALL
V-18 SERIES
ALUM TRAILER WALL
2167
(Revised 6.30.15)
COMPONENTS NOT SHOWN TO SCALE
KEITH Mfg. Co.
WORLD HEADQUARTERS
(800) 547-6161
(541) 475-3802
(541) 475-2169 fax
[email protected]
©2011 KEITH Mfg. Co. All Rights Reserved. KEITH, KEITH logo, V-Floor and WALKING FLOOR are registered trademarks of KEITH Mfg. Co. Equipment manufactured by KEITH Mfg. Co. is protected by numerous patents both
domestic and foreign. Manufactured under license.