Model FT7000XP
QUICK R EFERENCE GUIDE
THIS AREA FOR SERVICE PROVIDER
CONTACT INFORMATION:
TDN 07102-00071
04/2007
MANAGEMENT FUNCTIONS
- ACCESS I NSTRUCTIONS 1.
AT ATM WELCOME SCREEN, PRESS AND HOLD DOWN THE <CTRL> KEY (LOWER-RIGHT CORNER OF KEYPAD),
PRESS <1> KEY, THEN RELEASE BOTH KEYS . T HE S ECURITY L OGIN SCREEN WILL BE DISPLAYED.
2.
ENTER THE 2-DIGIT USER ID. PRESS <ENTER> KEY. ENTER THE USER PASSWORD AND PRESS <ENTER> KEY.
THE MANAGEMENT FUNCTIONS MAIN MENU IS DISPLAYED.
RESTART / SHUTDOWN TERMINAL
RESET ATM: FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT
FUNCTIONS. SELECT SYSTEM PARAMETERS, THEN RESTART TERMINAL.
SHUTDOWN TERMINAL: FOLLOW ACCESS INSTRUCTIONS TO ENTER
MANAGEMENT FUNCTIONS. SELECT SYSTEM PARAMETERS, THEN
SHUTDOWN TERMINAL. NOTE: THIS OPTION POWERS DOWN THE PC ONLY!
VIEW / CLEAR ATM SETTLEMENT TOTALS
THE VIEW ATM SETTLEMENT TOTALS DISPLAYS THE TOTAL NUMBER OF
CAPTURED CARDS AND DISPENSED CURRENCY WITH THE S TART AND E ND DATES.
THE START DATE IS THE LAST ATM SETTLEMENT RESET DAY AND THE END DATE
IS THE C URRENT DATE . T HE SETTLEMENT TOTALS ARE NOT CLEARED .
THE CLEAR ATM SETTLEMENT TOTALS RESETS ALL THE ATM SETTLEMENT TOTALS TO Z ERO (0) AND RESETS THE START DATE TO THE CURRENT DATE/
TIME.
! FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT TERMINAL SETTLEMENT
FUNCTIONS. CHOOSE VIEW ATM SETTLEMENT TOTALS. SELECT <PRINT> OPTION TO PRINT A REPORT.
REAR DISPLAY HOST SETTLEMENTS
! PRESS THE <ALT> AND “R” KEYS ON THE REAR KEYBOARD.
! WHEN PROMPTED, ENTER THE PIN NUMBER OF THE SETTLEMENT CARD.
! THE HOST/PROCESSOR SETTLEMENT SCREEN APPEARS. NOTE: OPTIONS
MAY VARY DEPENDING ON THE HOST.
2
REPLENISH CASSETTE(S)
THE REPLENISH CASSETTE(S) FUNCTION ALLOWS USER TO REPLENISH THE
MEDIA (CURRENCY, COUPONS, ETC) IN THE CASSETTE(S).
! FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SETERMINAL SETTLEMENT FUNCTIONS. CHOOSE REPLENISH
CASSETTE(S).
LECT
! A SCREEN
WARNING APPEARS THAT THE TIMEOUT FUNCTION NOR-
MALLY ASSOCIATED WITH MANAGEMENT FUNCTIONS IS DISABLED.
PRESS
<1> TO CONTINUE.
Note: The Fujitsu 510 dispenser does not have the capability to
lock/unlock cassettes. Cassette(s) may be removed/inserted at any
time.
! A SCREEN IS DISPLAYED THAT ALL CASSETTE(S) MAY BE REMOVED.
< FOLLOW THE CASSETTE REPLENISHMENT PROCEDURES >
! PRESS <1>
TO RETURN TO
TERMINAL SETTLEMENT FUNC-
TIONS.
ELECTRONIC JOURNAL
- DISPLAY LAST X THE DISPLAY LAST X FUNCTION IS USED TO DISPLAY AND PRINT RECORDS
FROM THE ELECTRONIC JOURNAL. RECORDS PRINTED USING THIS COMMAND
ARE NOT MARKED IN ANY WAY. THIS FUNCTION WILL NOT AFFECT ANY OTHER
JOURNAL FUNCTIONS.
! FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS.
SELECT ELECTRONIC JOURNAL.
CHOOSE DISPLAY LAST X RECORDS.
! PRESS <1> TO HIGHLIGHT THE NUMBER OF RECORDS
TO DISPLAY.
ENTER AN AMOUNT (#), THEN PRESS <ENTER>
KEY.
! PRESS <2>, PERFORM QUERY, TO DISPLAY THE RECORDS. SELECT <PRINT> OPTION TO PRINT THE REPORT.
3
REPLENISH CASSETTE(S) - NMD-100
1
STEP
ACTION
STEP
UNLOCK / OPEN CABINET.
GRASP
NOTE
ACTION
5
EXTEND “PAWLS” FULLY (INSERT) ON THE PUSHER PLATE.
6
CLOSE CASSETTE LID TO ITS
LOCKED POSITION . T HE
G REEN RELEASE BUTTON
SHOULD “POP” OUT. TURN
CASSETTE
HANDLE WITH ONE HAND
WHILE HOLDING THE MECHANISM WITH THE OTHER.
THE
CASSETTE
PULL
OUT
SLIGHTLY, THEN PLACE ONE
HAND UNDERNEATH AS YOU
SLIDE IT OUT.
2
PLACE CASSETTE ON A LEVEL SURFACE. INSERT KEY
INTO THE CASSETTE LOCK AND TURN CLOCKWISE. PRESS
GREEN RELEASE BUTTON TO RAISE LID.
KEY COUNTERCLOCKWISE TO
LOCK CASSETTE.
SLIDE CAS-
SETTE INTO ITS SLOT IN THE
MECHANISM.
3
4
MOVE PUSHER PLATE TOWARDS THE CASSETTE HANDLE.
PLATE SHOULD STAY INPLACE. LOAD NOTES USING 1" 2" STACKS OF CURRENCY.
7
REMOVE REJECT CASSETTE FROM MECHANISM. PLACE
ON LEVEL SURFACE. INSERT KEY INTO LOCK AND TURN
CLOCKWISE. PRESS GREEN RELEASE BUTTON TO RAISE
LID.
LEVEL
8
REMOVE
NOTE PILE BY HAND.
MOVE
PUSHER PLATE
AGAINST THE NOTES WITH ENOUGH PRESSURE TO HOLD
ANY REJECTED NOTES
-
BOTH SINGLE AND
BUNDLED AREAS. FOLLOW LOCKING PROCEDURES FROM
STEP 6 AND SLIDE CASSETTE BACK INTO MECHANISM.
NOTES BEFORE CLOSING.
Single Note Reject
Area
4
Bundled Note Reject
Area
REPLENISH CASSETTE(S) - FUJITSU 510
STEP
1 !
ACTION
UNLOCK / OPEN
CABINET.
PUSH
GRASP CASSETTE
GREEN RELEASE
BUTTON.
#
PULL
"
HANDLE AND
Release button
CASSETTE OUT SLIGHTLY,
THEN PLACE ONE HAND UNDERNEATH
AS YOU SLIDE IT OUT.
2 !
PLACE
"
O PEN
CASSETTE ON FLAT SUR-
Lid latch
FACE.
CASSETTE BY SLIDING
LATCH LEVER TO RIGHT AND LIFT LID.
#
FLIP LID BACK FULLY.
REMOVE ANY REJECTED NOTES FROM
REJECT AREA. NOTE: ONLY THE
TOP CASSETTE ACCEPTS REJECTS.
$
HOLD GREEN
KNOB AND PULL
PRESSURE PLATE BACK TOWARDS
REAR .
%
R ELEASE
KNOB AND ENSURE
PLATE IS LATCHED.
&
L OAD
NOTES USING
1" - 2"
STACKS OF CURRENCY.
3 !
M OVE
* IMPORTANT *
PRESSURE
BEFORE INSERTING CASSETTES IN THE FEED CHANNELS, ENSURE THE OPEN/CLOSE TAB (LOCATED IN
EACH CHANNEL) IS IN THE “CLOSE” POSITION. THE
TAB SHOULD BE IN THE POSITION SHOWN BELOW. IF
NOT, BILL FEED ERRORS WILL OCCUR!
PLATE
AGAINST THE NOTES WITH ENOUGH
PRESSURE TO HOLD NOTES BEFORE
CLOSING LID.
"
FOLD
CASSETTE LID DOWN TO
ITS LOCKED POSITION.
INSERT
CAS-
SETTE BACK INTO THE MECHANISM.
5
REPLACE PAPER (RECEIPT PRINTER)
STEP
1
ACTION
STEP
ACTION
2
PAPER REMAINS ON ROLL, CUT
OPEN UPPER LEFT CABINET DOOR.
PULL UP ON THE LOCKING PIN AND
IF
STEP
BETWEEN THE ROLL AND INPUT TO
3
PRINTER.
EXTEND PRINTER ASSEMBLY TRAY
ACTION
PUSH UP ON THE FEED BUTTON
(BLUE) REPEATEDLY TO ADVANCE
REMAINING PAPER FROM FEED PATH.
FULLY.
Feed button
4
REMOVE EXISTING PAPER ROLL AND/
OR SPINDLE FROM PAPER SUPPORT
5
BRACKET.
PLACE SPINDLE IN NEW PAPER ROLL.
CUT OFF ANY PAPER WHERE THERE
IS GLUE PRESENT.
6
ALIGN PAPER ROLL (W/SPINDLE) IN
PAPER SUPPORT BRACKET SLOTS .
ENSURE PAPER FEEDS FROM BOTTOM!
7
PASS END OF PAPER OVER THE TENSION ROLLER AND INSERT INTO THE
PRINTER TAKE-UP SLOT.
PRINTER
WILL AUTOMATICALLY GRAB PAPER.
8
FROM REAR SERVICE PANEL - ENTER MANAGEMENT FUNCTIONS >
DIAGNOSTICS > PRINTER. SELECT OPTION <3>, RESET. THE
PRINTER WILL RESET AND DISPLAY A STATUS REPORT. SELECT <PRINT>.
THE REPORT WILL PRINT TO THE RECEIPT PRINTER. PUSH PRINTER TRAY
BACK INTO CABINET. THE PRINTER IS NOW READY.
6
PAPER SPECIFICATIONS
PAPER S PECIFICATIONS
Width
80mm (+0/-1)
Diame te r
up to 254mm
Core diame te r (ins ide )
3-1/8"
up to 10"
~25mm
1"
PD450 (62 +/- 5 microns )
P350 (61 +/- 4 microns )
Pape r Thickne s s (ply)
PRINTER ACCESS AREAS
GREEN MARKINGS ON ASSEMBLY ARE DESIGNATED ACCESS AREAS.
$
#
"
!
7
REPLENISH ENVELOPES (ENVELOPE SUPPLY UNIT)
THE
OPTIONAL ENVELOPE SUPPLY UNIT HOLDS APPROXIMATELY 200 ENVELOPES. WHEN LOADING ENVELOPES, ALTER-
NATE EVERY
50-100 WITH THE FLAPS UP. FOR EXAMPLE, LOAD 50 WITH FLAPS UP FACING LEFT, THEN NEXT 50 WITH
RIGHT. THE ENVELOPE SIZE REQUIREMENTS ARE AS FOLLOWS:
FLAPS UP FACING
Envelope Siz e Requirements
Length
Width
Minimum
150 mm [5.91"]
95 mm [3.75"]
Maximum
244 mm [9.6"]
108 mm [4.25"]
Thickness
7 mm [.27"]
Note: Recommended siz e is a #10 envelope (104.8 mm x 238.1 mm)
1.
OPEN UPPER LEFT REAR CABINET DOOR. PULL UP ON TRAY LOCKING
PIN AND PULL THE ENVELOPE DEPOSITORY UNIT SLIDE TRAY OUT FULLY.
2.
FOLLOWING THE INSTRUCTIONS ON INSERTING ENVELOPES (LABEL ON
SLIDE TRAY BACK
INTO THE CABINET.
UNIT), LOAD ENVELOPES (FLAP UP INTO THE SUPPLY BIN).
* NOTE *
REMEMBER TO ALTERNATE ENVELOPES APPROXIMATELY EVERY
50 WITH FLAPS UP FACING LEFTRIGHT.
3.
ACCESS MANAGEMENT FUNCTIONS AND FROM THE MAIN MENU SCREEN
ENVELOPE DISPENSE AND
RETRACT TEST.
SELECT DIAGNOSTICS > ENVELOPE DEPOSITORY >
THE TEST DISPENSES AN ENVELOPE AND THEN AUTOMATICALLY RETRACTS IT
INTO THE DEPOSITORY STORAGE BIN (NORMAL OPERATION).
4.
AFTER THE TEST IS COMPLETE, PRESS <2> TO EXIT.
8
REPLACE RIBBON CARTRIDGE (ENVELOPE DEPOSITORY UNIT)
THE OPTIONAL DEPOSITORY ACCEPTS AN ENVELOPE, MONITORS ITS PROGRESS THROUGH THE UNIT, STAMPS IT WITH
68 CHARACTERS WITH THE DOT MATRIX PRINTER), AND DEPOSITS THE ENVELOPE IN THE
ENVELOPE DEPOSIT BIN.
IDENTIFYING DATA (UP TO
1.
REMOVE RIBBON CARTRIDGE FROM THE FOUR (4) PLASTIC TABS THAT HOLD IT.
2.
MOUNT THE NEW RIBBON CARTRIDGE INTO THE PRINTER HOLDER AS SHOWN BELOW. ENSURE CARTRIDGE ALIGNS
WITH THE PLASTIC TABS.
3. CONFIRM THAT THE RIBBON IS POSITIONED BETWEEN THE MASK AND HEAD, THEN TURN THE RIBBON KNOB IN A
“CLOCKWISE” DIRECTION UNTIL TAUT.
9
ELECTRONIC LOCK (LaGard)
ENTERING THE COMBINATION
THE ELECTRONIC LOCK COMBINATION CONSISTS OF SIX (6) DIGITS. IF LOCK IS
PROGRAMMED FOR DUAL CODE, EACH CODE WILL CONSIST OF SIX (6) DIGITS.
THE PRESET COMBINATION OF THE LOCK SHOULD ALREADY BE SET AT 1-2-3-45-6. AFTER INSTALLATION OF THE UNIT HAS BEEN COMPLETED, PERFORM THE
FOLLOWING STEPS:
* NOTE *
FOR DUAL CODE OPERATION, THE SECOND CODE MUST BE ENTERED
WITHIN TEN (10) SECONDS AFTER THE FIRST CODE WAS ENTERED.
1.
ENTER THE PRESET COMBINATION(S) AND CHECK FOR PROPER OPERATION. AFTER EACH KEYPRESS, THE LOCK
WILL BEEP. AFTER THE FINAL DIGIT HAS BEEN ENTERED, THE LOCK WILL BEEP TWICE AND THE OPEN PERIOD
WILL BEGIN.
2.
WITHIN FOUR (4) SECONDS, TURN THE KEYPAD “CLOCKWISE” TO THE OPEN POSITION.
3.
AFTER THE LOCK IS OPENED, THE DOOR MAY BE OPENED.
INVALID CODE ENTRY - LOCK WILL BEEP THREE (3) TIMES.
CHANGING THE COMBINATION
* IMPORTANT *
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN!
IF YOUR UNIT IS PROGRAMMED FOR DUAL CODE, EACH CODE MUST BE CHANGED INDEPENDENTLY. FOLLOW
THESE INSTRUCTIONS FOR EACH CODE CHANGE.
TO CHANGE THE COMBINATION OF THE LOCK, SIMPLY FOLLOW THESE DIRECTIONS.
1.
ENTER SIX (6) ZEROS.
2.
ENTER THE CURRENT COMBINATION (INITIALLY SET AT 1-2-3-4-5-6).
3.
ENTER THE NEW SIX (6) DIGIT COMBINATION TWICE.
- IF A MISTAKE IS MADE, WAIT THIRTY (30) SECONDS AND REPEAT THE FIRST 3 STEPS.
4.
TEST LOCK COMBINATION SEVERAL TIMES BEFORE CLOSING THE DOOR. THE COMBINATION IS NOW CHANGED.
VALID CODE ENTRY - DOUBLE SIGNAL AFTER VALID SIX (6) DIGIT CODE IS ENTERED.
INVALID CODE ENTRY - TRIPLE SIGNAL AND OLD CODE IS STILL VALID.
10
ELECTRONIC LOCK (LaGard)
SILENT SIGNAL ALARM
(IF FEATURE IS PROGRAMMED AND OPTIONAL ALARM BOX IS CONNECTED TO AN ALARM SYSTEM)
- ALWAYS PERFORM THIS OPERATION WITH THE DOOR(S) OPEN!
ENTER LAST DIGIT OF CODE ONE (1) NUMBER HIGHER OR ONE (1) NUMBER LOWER.
1.
EXAMPLE:
CODE: 1-2-3-4-5-6
DURESS: 1-2-3-4-5-5
OR
1-2-3-4-5-7
THE LOCK WILL OPEN WITHOUT ANY INDICATION THAT THE DURESS SIGNAL HAS BEEN SENT.
2.
LOCKOUT FEATURE
THE LOCK INCLUDES A WRONG TRY PENALTY LOCKOUT FEATURE THAT PREVENTS ENTRY FROM UNAUTHORIZED
THIS FEATURE PERFORMS AS FOLLOWS:
PERSONNEL.
•
ENTRY OF FOUR (4) CONSECUTIVE INVALID COMBINATIONS STARTS A 5-MINUTE DELAY PERIOD.
- LED FLASHES RED AT TEN (10) SECOND INTERVALS.
•
AT THE END OF THE DELAY PERIOD, TWO (2) MORE CONSECUTIVE INVALID COMBINATIONS WILL RESTART AN ADDITIONAL
5-MINUTE DELAY. ENTRY WILL NOT RESPOND TO A SINGLE KEYSTROKE DURING DELAY PERIOD.
BATTERY LOW WARNING
REPEATED BEEPING DURING AN OPENING INDICATES THAT THE BATTERY IS LOW AND NEEDS TO BE REPLACED. RECOMMEND REPLACEMENT OF BATTERY AT LEAST ONCE ANNUALLY. THE BATTERY BOX IS LOCATED ON THE INSIDE OF THE DOOR.
NOTE: IF THE LOCK WILL NOT OPERATE (I.E. REPEATED BEEPING OR NO BEEPING) WHILE THE DOOR IS CLOSED AND LOCKED, THE
BATTERY MUST BE ENERGIZED FROM THE TWO EXTERNAL TERMINALS ON THE FRONT OF THE PUSH-BUTTON PANEL.
TO ENERGIZE THE LOCK, CONNECT A 9-VOLT ALKALINE BATTERY ON THE EXTERNAL TERMINAL POINTS. MAINTAIN
CONTACT, ENTER A VALID COMBINATION, AND TURN THE DIAL CLOCKWISE TO OPEN THE LOCK.
NOTE: YOU MUST MAINTAIN BATTERY CONTACT AT ALL TIMES THROUGHOUT THIS PROCEDURE.
CHANGING THE BATTERY
1.
OPEN THE ATM VAULT DOOR(S). REMOVE THE BATTERY BOX COVER BY PULLING THE FRONT PORTION AWAY FROM
THE VAULT DOOR.
2.
THE CONNECTOR IS EASILY REMOVED BY UNSNAPPING IT FROM THE TWO (2) TERMINAL ON THE TOP OF THE BATTERY.
3.
REMOVE THE OLD BATTERY. INSTALL/CONNECT A NEW 9-VOLT ALKALINE BATTERY.
4.
PUSH THE BATTERY AND THE LEADS COMPLETELY UP INTO THE BATTERY COMPARTMENT.
5.
REINSTALL THE COVER AND TEST THE UNIT SEVERAL TIMES BEFORE CLOSING THE VAULT DOOR.
11
ENVELOPE DEPOSIT BIN
THE SECURE ENVELOPE DEPOSIT BIN STORES DEPOSIT TRANSACTIONS. T HE CUSTOMER INSERTS AN ENVELOPE CONTAINING CHECKS OR BILLS ( NOT COINS), THE DEPOSITORY UNIT ACCEPTS THE ENVELOPE, STAMPS IT , AND DEPOSITS IN
THE ENVELOPE BIN.
RECOMMENDATION
THE ENVELOPE DEPOSITORY STAMPS DEPOSITED ENVELOPES WITH IDENTIFYING DATA . THIS DATA IS STAMPED APPROXIMATELY IN THE MIDDLE
OF THE ENVELOPE AS SHOWN IN THE FIGURE AT RIGHT. IF YOUR ENVELOPES HAVE A LOGO / GRAPHIC THAT IS AT OR NEAR THE CENTER , THIS
DATA WILL PRINT OVER THIS AND MAY MAKE IDENTIFICATION HARD TO
DETERMINE. RECOMMEND EITHER MOVING YOUR LOGO UP TO THE CORNERS OR USE PLAIN ENVELOPES .
REMOVE:
1.
OPEN LOWER (LEFT) REAR CABINET DOOR. PULL THE BIN OUT SLIGHTLY, THEN PLACE ONE HAND UNDERNEATH AS
YOU SLIDE IT OUT FROM THE GUIDE RAILS.
2.
INSERT THE KEY AND TURN IT 90° CLOCKWISE. CLOSE THE COVER (HELD BY A MAGNET). TURN THE KEY BACK TO
SECURE.
MOUNT:
1.
INSERT THE KEY AND TURN IT 90° CLOCKWISE. OPEN THE COVER (HELD BY A MAGNET). TURN KEY BACK TO
REMOVE.
2.
WITH
ONE HAND UNDERNEATH BIN, GRASP HANDLE AND SLIDE BACK INTO THE GUIDE RAILS.
FORWARD UNTIL IT
“CLICKS”.
12
SLIDE
THE BIN