Introduction ¾ What is extrusion of metals? Chapter 15 Extrusion and Drawing of Metals Alexandra Schönning, Ph.D. Mechanical Engineering University of North Florida Forcing of a billet through a die Can create solid and hollow cross sections A semi-continuous process (each billet is extruded individually). • Discrete products by cutting into desired lengths ○ Gears, brackets, coat hangers Carried out at room temperature or at elevated temperature. Often combined with forging process ¾ What is drawing of metals? Changing or reduction of the cross section of a rod, wire, or tube by pulling it through a die ¾ What products are made using drawing? Rivets, bolts, screws Round and non-round profiles What is the difference between extrusion and drawing? • Push or draw… • Fasteners, parts for bicycles, cars, … ¾ What is made using extrusion? Figures by Manufacturing Engineering and Technology Kalpakijan and Schmid Railings for slidng doors, tubing ¾ What material is generally extruded? Aluminum, copper, steel, magnesium, lead, plastics direct extrusion process Page 15-1 Example of products made using extrusion Page 15-2 The extrusion process ¾ Names of the process Extrusion Direct extrusion Forward extrusion ¾ Other types of extrusion processes Indirect extrusion • The die moves toward the billet ¾ What are the process steps? Round billet is placed in a chamber The billet is forced through the die using a hydraulically driven ram or a pressing stem Die opening may have round or non-round cross section Hydrostatic extrusion • The billet is smaller in diameter than the chamber. • The billet is surrounded by a fluid • The pressure is supplied by a ram • Friction is low Impact extrusion Figure 15.2 Extrusions, and examples of products made by sectioning off extrusions. Source: Kaiser Aluminum. Page 15-3 Extrusion Variables ¾ Geometric Variables Die angel, α Extrusion Ratio: R Extrusion Force ¾ Circumscribing circle diameter (CCD) ¾ The extrusion force required depends on • Ao/Af: Ratio of the cross sectional area of the billet to the A of the extruded part ¾ Temperature ¾ Speed of ram ¾ Lubricant type Page 15-4 Diameter of the smallest circle that the cross section can fit within. ¾ Shape factor Billet material strength Extrusion ratio Friction billet/chamber and billet/die Temperature Speed F Ao⋅ k⋅ ln Ao Af ¾ k = extrusion constant Metal and temperature dependent One of the variables determining the complexity of extrusion Ratio of perimeter of extruded product to the cross sectional area. • Circle has the smallest shape factor Page 15-5 Page 15-6 1 Metal Flow in Extrusion ¾ Effects the mechanical properties of the part ¾ The metal flows longitudinally, resulting in an elongated grain structure Extrusion Practice ¾ What materials are extruded? ¾ Dead zone ¾ Straitening and twisting Aluminum, copper, magnesium, alloys, steels Metal at corners is almost stationary ¾ Extrusion ratio R = Ao/Af 10 to 100 Lower for less ductile materials At least R=4 to work the material in the plastic region ¾ Length of extruded materials May be required for small cross sections ¾ Die angle causes a butt end Remains in the chamber after operation is complete Cut off as scrap ¾ Stepped extrusion Extruding the billet partially in one die and then one or more dies < 7.5 meters typically 30 meters max ¾ CCD (circum scribed diameters) 6 mm – 1m for Aluminum ¾ Ram speeds Up to 0.5m/s Lower for aluminum, copper Higher for steels Page 15-7 Page 15-8 Hot Extrusion Die Designs and Die Materials ¾ Square dies ¾ Why hot extrusion? For metals that don’t have sufficient ductility at room temperature Reduce the required extrusion force ¾ Disadvantages and problems Die wear due to high operating temperatures Cooling of the billet in the chamber – non-uniform extrusion Created by fitting a mandrel to the ram Wall thickness, typically • Creates a die angle • Reduce effects of problem by heating the die prior to extrusion (a) • > 1 mm Al • > 3 mm carbon steel • > 5 mm stainless steels (c) Oxide film develops on surface • May be abrasive • Affects the flow pattern of the metal • Reduce/remove this problem by using a dummy block in front of the ram ¾ Tubes Used for non-ferrous metals Dead metal zones develop direct extrusion process (b) ○ Oxidized layer is left in the container • Reduce/remove this problem by heating the billet in an inert-atmosphere furnace Die design: tapered Page 15-9 Hollow Sections ¾ Welding chamber methods using special dies. ¾ How does this method work? Metal divides and flows around the supports of the internal mandrel. Page 15-10 Good vs. Bad Cross Section ¾ What materials does this work for? Materials that reweld well under high pressure • Aluminum ¾ Lubricants can’t be used Prevents rewelding ¾ Important Symmetry of cross section Eliminate sharp corners Keep section thickness uniform Avoid extreme change in the dimensions of the cross section • This results in strands Rewelding of the strands occur within the chamber after the supports and before the die • High pressure makes this possible Figure 15.10 Poor and good examples of cross-sections to be extruded. Note the importance of eliminating sharp corners and of keeping section thicknesses uniform. Source: J. G. Bralla (ed.); Handbook of Product Design for Manufacturing. New York: McGraw-Hill Publishing Company, 1986. Used with permission. Page 15-11 Page 15-12 2 Die Materials and Lubrication Cold Extrusion ¾ Often involves different manufacturing operations such as direct and indirect extrusion and forging. ¾ Used in making ¾Die materials Hot worked die steels Coatings may be applied to extend life Tools and components in cars, motorcycles, bicycles, appliances… ¾Lubrication Glass: a glass cylinder is placed in the die entrance of the chamber. The billet heats the glass and the molten glass acts as a lubricant at the die interface. Jacketing or canning • If the metal is likely to stick to the container walls, then the billet can be enclosed by a thin-walled container of a softer metal. ¾ Advantages over hot extrusion Improved mechanical properties through work-hardening Good control of dimensional tolerances Improved surface finish Elimination of need for billet heating ¾ Disadvantages Stress magnitudes on the tools are high Æ wears the die ¾ Lubrication Applied to the workpiece Page 15-13 Page 15-14 Examples of Cold Extrusion Impact Extrusion ¾ Typically considered a cold extrusion process ¾ Components Die Blank (or slug) Punch ¾ Punch forces the blank to extrude backward Page 15-15 Page 15-16 Hydrostatic Extrusion Extrusion Defects ¾ Incompressible fluid surrounds the billet ¾ Surface cracking At high temperatures: Vegetable oils are used • Resulting from too high temperature, friction, speed • Surface starts to crack and then tear ¾ Billet is a little smaller than the container ¾ Usually at room temperature ¾ Advantage At lower temperatures No container wall friction Brittle materials can be extruded using this method since the ductility increases with the hydrostatic pressure Small die angles and high extrusion ratios can be used ¾ Disadvantage Tooling is complex Results in minimal industrial applications Page 15-17 • Bamboo defect ○ The billet may temporarily stick, the pressure increases and the billet moves forward. ¾ Pipe effect ¾ Internal Cracking Due to tensile stresses at the center line in the deformation zone Tendency of center cracking • Increases with increased die angle • Increases with increased amount of impurities • Decreases with increasing extrusion ratio and friction Surface oxides and impurities are drawn to the center of the billet (like a funnel) Minimize by making the flow pattern more uniform (reduce friction and temperature gradients) Page 15-18 3 The Drawing Process Extrusion Equipment ¾Most common are horizontal hydraulic presses ¾ What is it? Speed of the operation can be controlled The cross-section of a round wire/rod is reduced in size or changed in shape by pulling it through a die. ¾Cold extrusion Typically vertical hydraulic presses More economical as they require less floor space ¾ Variables Amount of reduction in crosssectional area Die angle • Optimum angle for minimum drawing force can be computed. • Other product quality dimensions may require a different angle. ¾ Drawing force (F) Ao F Yavg⋅ Af ⋅ ln Af Yavg: average stress of material drawn Af: exit cross-sectional area Ao: initial cross-sectional area ¾ Max reduction in cross-sectional area: 63% Friction along die/workpiece Drawing speed Figure 15.17 General view of a 9-MN (1000-ton) hydraulic-extrusion press. Source: Courtesy of Jones & Laughlin Steel Corporation. Page 15-19 Page 15-20 Drawing Process / Practice ¾ Drawing of other shapes Initial cross section is typically round or square Mandrels can be used for internal cavities Ironing can be used to obtain flat sheets (a wedge shaped die is used) Die Design ¾ Drawing speed Material dependent 1 m/s to 50 m/s (fine wire) ¾ Typically reductions in area are kept below 45% ¾ Sizing operations Small reduction in area Used primarily to improve surface finish and dimensional accuracy ¾ Annealing may be necessary between passes to maintain sufficient ductility in the material ¾ Bundle drawing Numerous wires can be drawn at the same time. Can result in wires as fine as 4µm. ¾ Die angles usually range from 6o to 15o ¾ Typically have two angles: approach and relieve angle ¾ Basic design has been developed through trial and error ¾ The land gives the final dimension of the product ¾ Die materials Tool steels Diamonds • Used for fine wire • Used as inserts Page 15-21 Page 15-22 Lubrication Defects and Residual Stresses ¾Wet drawing ¾ Defects Similar to those of extrusion Dies and the rods are completely immersed in the lubricant • Common is center cracking ¾Dry drawing Seams are common The surface of the rod is coated with the lubricant (soap) • Longitudinal scratches or folds in the material ¾Coating ¾ Residual Stresses Common in cold drawn products Sometimes to an advantage; sometimes to a disadvantage Warping may occur if material is removed Rod or wire is coated with a soft metal acting as lubricant ¾Ultrasonic vibration of the dies and mandrel Reduce forces, improve surface finish, and improve die life Page 15-23 Page 15-24 4 Drawing Equipment Roll Straightening ¾ Draw bench A single die Used for diameters > 20 mm Lengths < 30 m Figure 15.22 Schematic illustration of roll straightening of a drawn round rod (see also Fig. 13.7). ¾ Bull block Usually multiple dies are used Lengths = several kilometers Page 15-25 Page 15-26 5
© Copyright 2026 Paperzz