BEAVER
MANUFACTURING
PRODUCT CATALOGUE
Greaseless Compound
Polishing Lubricant
Full Disc Cloth Buffing Wheels
Leather Aprons
Rubber Expanding Wheels
Non Woven Finishing Buffs
Non Woven Locking Belts
Blue & Red Devils
Beaver Hand Pad
Bar Compound
Buffing Lathe Hex Nuts
Lump Pumice
Washer & Flanges
TABLE OF CONTENTS
YOUR CONTACT LIST
Claudio D’Alessio
CEO
[email protected]
JoAnne
Accounting
[email protected]
Helma
Customer Care
[email protected]
Yhojana
Order Desk
[email protected]
Greaseless Compound…………………………………….
Bar Compound…………………………………………….
Polishing Lubricant……………………………………….
Full Disc Cloth Buffing Wheels………………………….
Blue Devil………………………………………………….
Red Devil…………………………………………………...
Beaver Hand Pad…………………………………………...
Non Woven Locking Belts………………………………….
Non Woven Finishing Buff………………………………….
Sanding Stars……………………………………………….
Flutter Sheets……………………………………………….
Slashed Assembly…………………………………………..
Vonnegut Brushes………………………………………….
Felt Wheels………………………………………………….
Canvass Sleeves…………………………………………….
Leather Aprons……………………………………………..
Rubber Expanding Wheels…………………………………….
Buff Clamping Assembly……………………………………
Side Flanges…………………………………………………
Mandrels…………………………………………………….
Washer & Flanges…………………………………………...
Buff Rake…………………………………………………….
Buffing Lathe Hex Nuts……………………………………..
Lump Pumice………………………………………………..
Whitening Powder…………………………………………..
Speed Chart…………………………………………………
GREASELESS COMPOUND
BEAVER
As the name implies, Greaseless Compounds are made entirely free of any grease
binders such as tallow, oil wax, etc. Using animal hide glue as the binder, abrasive
grain is blended into this glue base to form a uniformly mix “greaseless” compound.
When applied to a revolving buffing wheel, the frictional heat created causes the
compound to melt, thus an even coating of glue and abrasive grain is transferred to
the wheel.
Greaseless Compound is available
in the following grit sizes:
BG 80
BG 240 BLUE
BG 120
BG 300
BG 150
BG 400
BG 180
BG-Fine Finish
BG 200
BG-GLUE
BG 240
Greaseless is packaged in an easy to use
plastic tube. Each tube is approximately
2-1/2” x 9” long and weighs about 3 pounds.
Available in 45 pounds case which holds
15 tubes.
Application Tip
Start with a clean dry wheel and rake it out to open the face. Peel the plastic covering
back a few inches to expose the compound. If you are using a variable speed lathe;
slow it down to minimum speed and apply the compound to the face of the wheel
with short strokes. When using a single speed lathe above 1200 rpm, let the lathe
come up to speed, then shut it off and use the compound tube as a brake to stop the
wheel.
Repeat this process until a thick head has been formed on the wheel surface, letting
the compound dry with the wheel in motion between applications. With a new wheel,
it can take several minutes to build a good head.
CG - 1
BAR COMPOUND
BEAVER
TRIPOLI
(Nonferrous metal, Brass, Aluminum,
Zinc Die Cast)
BB4W Brown (Heavy Cut-High Colour)
BB5A Brown (Heavy Cut-Medium Colour)
COLOUR COMPOUND
(Tableware, Decorative Hardware, Fixtures etc.)
BB36X
BB18
BB9
BB1
BBKC11
Green
Green
Green
White
White
(High Colour-High Grease)
(High Colour-High Grease)
(High Colour-Med, Grease)
(High Colour-Low Grease)
(High Colour-Very Dry)
CUT COMPOUND
(Stainless Steel and Aluminum for decorative
hardware, Cookware, Automotive etc.)
BB41 W-Gray
BB40 Black
(Heavy Cut-High Grease)
(Heavy Cut-High Grease)
CUT & COLOUR
(Stainless Steel Cookware, Cutlery, Lamps,
Automotive, Appliances)
BB11V Yellow (Medium Cut-Medium Color)
ANIMAL FAT FREE
BBFF47
BBFF17
BBFF45
BBFFKC11
Black
Yellow
Green
White
(Heavy Cut-Med Grease)
(Cut & Colour-Dry Grease)
(Colour-Dry Grease)
(High Colour-Med. Grease)
JEWELLERS ROUGE
BBR
BBR
BG - 1
1 Green (Med Colour)
2 Red
(Fine Colour)
WHEELS & BELT POLISHING LUBRICANT
BEAVER
POLISHING LUBRICANTS
Polishing lubricants are designed for wheels and belts set
with aluminum oxide, silicon carbide or Turkish emery grade.
Often used with second or third stage polishing operations
prior to buffing.
The application of lubricants to an abrasive belt or wheel
produces a softer more forgiving cutting action and result in
a surface that is easier to buff out.
BPL-G1
Yellow grease with a low melting point. Primarily for polishing
wheels or belts, it can also be used as a saw lubricant.
BPL-G6
A higher melting point yellow tallow, medium hard grease for
polishing wheels.
BPL-G11
High quality saponifiable yellow tallow grease for applications
where cleaning is a problem.
PC - 1
WHEELS & BELT POLISHING LUBRICANT
BEAVER
LUMP PUMICE
P.N
DESCRIPTION
BLP Pumice
SOLD BY
Pound (lbs.)
Sizes from a softball to a basketball
Sold as one piece up to a bag weighing 80 to 120 lbs.
Good for redressing buffs to remove greasy compound and reface the buff.
WHITING POWDER
P.N
BWP
DESCRIPTION
White Calcium Powder
SOLD BY
Pound (lbs.)
Used to remove light grease haze left over from buffing to better observe the buffed surface.
Just sprinkle on the work piece and wipe off with a soft cloth or cotton glove.
Comes in 50-lbs. bags or can be broken down.
PC - 2
FULL DISC CLOTH BUFFING WHEELS
BEAVER
COTTON AVAILABLE
Canton
Flannel
6020C
60 x 60 Untreated Soft Cotton
6016C
60 x 60 Untreated Med. Cotton
80C
80 x 80 Untreated Cotton
90C
86 x 82 Untreated Cotton
90Y
86 x 82 Yellow Treated Cotton
Sisal
Available Sizes
4”
6”
8”
10”
12”
14”
16”
STITCH TYPE
FACE WIDTH
1/2” approx. 12 ply
1/2” approx. 40 ply
1/2” approx. 36 ply
1/2” approx. 54 ply
1/2” approx. 36 ply
1/2” approx. 36 ply
1/2” approx. 7 ply
To Order Conventional Full Disc Buff, Specify the Following:
x
Diameter
x
No. of Ply
Arbour Holes
x
Material
x
Type of Stitch
Spacing for Stitch
STITCH SPACING
APPLICATION
SOFTER ———— HARDER
LOOSE
COLOUR
CONCENTRIC
COLOUR
TANGENT
SPIRAL
SQUARE
One row around arbor hole only
1,
3/4,
1/2,
3/8,
1/4
CUT & COLOUR
CUT
12,
1,
24,
3/4,
36,
1/2,
48,
3/8,
58
1/4
CUT
1,
3/4,
1/2,
3/8,
1/4
The density of thickness is controlled by the width of space between the stitching...the closer the
sewing the harder the buffs.
CB - 2
BUFFS
BEAVER
FULL DISC
CONVENTIONAL SEWN
COLOUR
CUT
LOOSE
COLOR
SPIRAL
STITCHING
CUT/COLOUR
CONCENTRIC
TANGENT
CUT
SQUARE
DESCRIPTION
Loose
Sewn once around the hole for light cutting down & colouring
Spiral
Rows are sewn spirally from centre to edge
Circular
Rows are concentric which each role forming a complete circle
Square
Rows of stitching runs from one edge of the buff to the other
Tangent
Rows of stiching run from the edge to the centre in an arc form
BUFF SELECTOR CHART
Types of Material to be
Finished
Extruded Aluminum
Cast Aluminum Alloy
Chromium
Copper
Nickel & Alloys
Plastics
Precious & Semi Precious
(Gold, Silver etc.)
Steel & Stainless Steel
Titanium
Zinc
Wood
CB - 1
CUT-DOWN BUFFING
COLOR BUFFING
SATIN FINISHING
Sewn Sewn
Sewn Full Disc Full Disc Loose Full Disc Full Disc
Cloth
Sisal Flannel Loose
Sewed Flannel
Loose
Sewed
86/82
60/60,
60/60,
60/60,
60/60,
80/80
80/80
80/80
80/80
NON WOVEN
BEAVER
BLUE DEVIL MED. A/O
Sizes Available 4” to 20” Diameter
Specify Arbor Hole Size
Sizes
6”
8”
12”
Maximum RPM
3,600
2,700
1,800
High Strength Products Characteristics:
Very comfortable and durable. High strength
is the best product for light deburring and
finishing applications.
Impacting a final finish on contoured parts
Final finish on brass and steel doors
Light edge deburring on structural aircraft
aluminum parts
Light edge deburring on stainless steel.
RED DEVIL DISCVERY FINE. A/O
Sizes Available 3” to 6” Diameter
Specify Arbor Hole Size
Product Characteristics:
Designed for power applications
They can be used with jitterbug, orbital
and straight line Sanding
NW - 1
NON WOVEN
BEAVER
BEAVER HAND PADS
Product Characteristics:
Tough cutting and aggressive material for medium duty cleaning,
yet soft and pliable to conform to irregular surfaces.
P/N
SIZE
COLOR
GRADE
B440
6” X9”
TAN
X-COARSE
B440
6” X9”
MAROON
B440
6” X9”
GREEN
VERY FINE
B440
6” X9”
GREY
ULTRA FINE
B440
6” X9”
WHITE
NON-ABRASIVE
COARSE
LOCKING BELTS - 30 mm X 660 mm
GRADING GRIT RANGE
COLOR
Coarse
60/80
Brown
Medium
100/150
Maroon
Very Fine
280/360
Blue
* Other Lengths Available upon request
FINISHING WHEELS
Synthetic fibre, used dry, produces a satin finish.
Buffs have leather patches in center to provide firm
grip on tapered spindle
Diameter
3
4
NW - 2
Ply
2
2
Grade
Very Fine
Very Fine
Grain
A/O
A/O
SANDING STARS
BEAVER
SANDING STARS
SANDING/FINISHING/POLISHING:
Excellent for sanding, scuffing and blending wood
or metal. Ideal choice to replace hand sanding on
contoured or molded surface.
Size Available
4”
8”
Available in J Weight , 1/4” Slash
Grits Available 80, 100, 120, 150, 180, 220, 320, 400
Available in A/O or S/C
FLUTTER SHEETS
FLUTTER SHEETS
**Tips for Flutter Sheet Set-up and Use
figure 1
1. Place two sheets back to back, see figure
2. Crisscross them to form a wheel, see figure
2 and3. Repeat the pattern until you have 15
to 20 sheets on the arbor, tighten the nut to h
old the sheets together.
Available in J Weight
Size
Grits Available
BFS-3
80, 120, 180, 220, 320
BFS-4
80, 120, 180, 220, 320
BFS-6
80, 120, 180, 220, 320
BFS-8
80, 120, 180, 220, 320
3. Secure the assembly in your tool, be sure to
tighten the chuck adequately. Operate at
maximum speed of 2,300 RPM. It is strongly
suggested that you do not exceed the
maximum RPM.
figure 2
figure 3
4. Before using the flutter sheets on your
project, break in the edge on a scrap piece
wood to soften the edge and prevent gouging.
SS - 1
SLASHED ASSEMBLES
BEAVER
FOR BRUSH BACKED POLISHING HEADS
Size Available
1 x 10
1 x 16
1 x 10
2 x 10
2 x 16
4 x 16
6 x 16
VONNEGUT LOADINGS
FINISHING/POLISHING - Sharp Silicon Carbide
or Aluminum Oxide grain on X weight backing.
Slashed pattern gives flexibility in sanding contour
shapes. Loadings used to refill Vonnegut wheels to
sand intricate shapes and dimensions. Primarily used
for woodworking, but can also be used for finishing
metal, plastic fibreglass.
Avail. Grits :- 80, 100, 120, 150, 180,
220, 320, 400
Available in Stapled or Glued
Available in 1/4 or 1/8 Staggered Slash
Aluminum Oxide or Silicon Carbide
VONNEGUT REPLACEMENT BRUSHES
FINISHING/ POLISHING - For use with Vonnegut loadings
Vonnegut Replacement Brushes
Size
2” Brush Replacements
4” Brush Replacements
6” Brush Replacements
SA - 1
Short
BVB2”S
BVB4”S
BVB6”S
Long
BVB2”L
BVB4”L
BVB6”L
FELT WHEELS
BEAVER
SOFT
MEDIUM
HARD
SIZE AVAILABLE
2
3
4
5
6
Available in 1/4” thick and 1/2” think.
Available soft, medium, hard
Specify bore size when ordering
FW - 1
APRONS FOR POLISHERS
BEAVER
SEAMED
TYPE
Apron with BIB
Waist Apron
HD Polisher Apron
SEAMLESS
SIZE
24 x 36
24 x 24
24 x 36
HEAVY DUTY
FEATURES
Neck and waist strap
Waist ties
Neck strap, adjustable
waist strap and pen pocket
CANVAS SLEEVES
*
*Canvass Sleeves does not include Pneumatic
drums displayed
AVAILABLE SIZES
3x9
4x9
6x9
8x9
3x7
4x7
6x7
Canvas Sleeves are used to go between the pneumatic drum and sanding sleeves. It protects
the rubber bladder from wear and tear caused by loose abrasive.
PA - 1
ACCESSORIES
BEAVER
RUBBER EXPANDER WHEELS
Dia.
3
4
6
FACE WIDTH
1/2
1
BRCW 3x1/2 BRCW 3x1
BRCW 4x1/2 BRCW 4x1
BRCW 6x1/2 BRCW 6x1
2
BRCW 3x2
BRCW 4x2
BRCW 6x2
5/8 Bore dia. Is standard, but other bore sizes are available.
Other sizes are available
RUBBER HARDNESS GUIDE
Belt Roughness Grit
Recommended Durometer
36
85, 75, or 65
60
80
65
120
55
150
55
180
50
240 & higher
Fine 45
AC - 1
ACCESSORY HARDWARE
BEAVER
3” CRO AIRWAY BUFF CLAMP ASSEMBLY
PN
BFLG - 001A
BFLG – 002A
BFLG – 001B
DESCRIPTION
For 1 Buff
For 2 Buff
Side Flange
**Used to clamp Airway Buff that have 3”CRO center
hole and assembly on your hand held tool.
BUFF RAKE
DESC.
Rake Assembly
Consisting of
Rake Head
Wood Handle
Hardware
Used to remove dried compound as well as fluffing Buffing wheels and truing their face. The rake
head can be replaced when it wears out.
AC - 2
ACCESSORY HARDWARE
BEAVER
MANDRELS
PN
BMandrel-1
BMandrel-2
DESC.
5/8-11 x 2-5/8
5/8-11 x 3-5/8
*Use as extensions for angle grinders and straight grinders.
BUFFING LATHE HEX NUTS
SIZE PITCH THREAD SHAPE
1-1/4
5
ACME
1-1/4
6
ACME
1-1/4
6
SQUARE
1-1/4
7
ACME
RIGHT HAND
BHN-5AR
BHN-6AR
BHN-6SR
BHN-7AR
LEFT HAND
BHN-5AL
BHN-6AL
BHN-6SL
BHN-7AL
2” A/F BRASS
WASHERS & FLANGES
*
PN
*BFLG - 003
BFLG – 001-2F
BFLG – 001-3
BFLG - 001-B
DESC.
2 -1/4 x 5/8-11
2-1/4 x 5/8
3 x 5/8
4 x 5/8
AC - 3
ACCESSORY HARDWARE
BEAVER
PROPER BUFF SET UP
CENTRE DISC
P/N
BCD-3
BCD-5
BCD-7
AIRWAY CRO
3
5
7
ARBOR HOLE
5/8
1-1/4
1-1/4
** Other Arbor Hole Sizes Available
Locking type center discs are used to hold the bias airway Buff center only. These are
held in place by the heavy duty side flanges
SIDE FLANGES
Steel side flanges are used to properly clamp bias airway buffs
that have clinch rings. The flanges are at least larger than the
metal clinch ring diameter. (i.e the flanges must cover the
clinch ring fingers
PN
BSF-3
BSF-5
BSF-7
BUFF CTR
3
5
7
FLANGE O/D
4
6
8
BORE SIZE
5/8
1-1/4
1-1/4
**Other Bore Sizes Available
AC - 4
MEASUREMENT CHART
BEAVER
RPM
at
Arbor
or
Spindle
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
3200
3400
3600
3800
4000
4
6
Diameter of Wheels in Inches
10
12
14
16
18
8
20
22
24
4608
5184
5760
6336
6912
7488
8064
8640
9216
9792
10368
10944
11560
12096
12672
13248
13824
14400
14976
15552
16128
16704
17280
18431
19583
20735
21887
23039
5026
5655
6283
6911
7540
8168
8796
9425
10053
10681
11310
11938
12566
13194
13822
14451
15079
15708
16336
16964
17592
18221
18850
20107
21363
22619
23876
25132
Surface Speed in Feet per Minute (S.F.P.M)
837
942
1047
1152
1256
1361
1466
1571
1675
1780
1885
1989
2094
2199
2304
2408
2513
2618
2722
2827
2932
3037
3141
3351
3560
3769
3979
4188
1256
1413
157
1727
1884
2042
2199
2356
2513
2670
2827
2984
3141
3298
3455
3612
3770
3927
4084
4241
4398
4555
4712
5026
5340
5654
5969
6283
1675
1885
2094
2304
2513
2723
2932
3142
3351
3560
3770
3979
4189
4398
4608
4817
5027
5236
5445
5655
5864
6074
6283
6702
7121
7539
7958
8377
2094
2356
2618
2880
3142
3404
3666
3927
4189
4451
4713
4975
5236
5498
5760
6022
6284
6545
6807
7069
7331
7592
7854
8378
8901
9425
9948
10472
2513
2817
3141
3455
3769
4084
4398
4712
5026
5340
5654
5969
6283
6597
6911
7225
7540
7854
9168
8482
8796
9110
9425
10053
10681
1109
11938
12566
2932
3298
3665
4031
4398
4764
5131
5497
5864
6230
6597
6963
7330
7696
8063
8429
8796
9162
9529
9895
10262
10629
10996
11729
12462
13193
13927
14661
3351
3770
4189
4608
5027
5446
5865
6284
6703
7121
7540
7959
8378
8797
9415
9634
10053
10471
10890
11309
11728
12147
12566
13404
14242
13079
15917
16755
3770
4241
4712
5183
5655
6126
6597
7069
7540
8011
8482
8954
9425
9896
1036
1083
11310
11781
12253
12724
13196
13667
14137
15079
16022
16964
17907
18850
4189
4712
5236
5760
6283
6807
7330
7854
8678
8901
9425
9948
10472
10996
11519
12043
12566
13090
13613
14136
14660
15184
15708
16755
17802
18850
19897
20944
Note: Within the speed range of each size of buff, the higher speed is for cutting and the
lower speed is for colouring.
MC - 1
GENERAL TERMS AND CONDITION OF SALE
BEAVER
NEW ACCOUNTS
To establish an open account you must supply three accepatable credit
references and a bank reference. Untill credit has been established all orders
to be paid via Visa / Master Card and or Debit.
QUANTITY VARIANCE
Due to the nature of manufacturing, Beaver reserves the right to over or
undership each item quantity by 10% unless exact quatities are specified.
PAYMENT TERMS
Net 30 days. Any invoices not paid within 45 days will be considered
deliquent and all in house orders will be put on hold until all past due
invoices have been paid in full.
FREIGHT TERMS
FOB - Our plant Brampton Ont.
RETURNED GOODS
No merchandise can be returned without prior authorization and will not be
accepted without the proper RGA (Returned Goods Authorization) number.
PRICING
All prices quoted are plus applicable taxes
ADD ON POLICY
Every effort will be made to accomodate “add on” requests but under certain
circumstances your order will be “deemed” closed and all above conditions
will be in effect
TC - 1
BEAVER
MANUFACTURING
DISTRIBUTED BY