TECHNICAL DATA SHEET
DRiBOND
A revolutionary polymer modified dry mudset.
PRODUCT DESCRIPTION:
DriBond is a polymer modified dry-mudset for use with thinsection concrete pavers and natural stone to enhance and beautify
any horizontal concrete surface with the look and feel of traditional
pavers.
RECOMMENDED FOR...
DriBond™ is recommended as a mortar bed for 1” thin-section
pavers over horizontal concrete surfaces for:
-
-
Residential driveways, sidewalks, pool decks, patios,
courtyards garage floors
Commercial and light industrial driveways, sidewalks,
walkways, courtyards
NOT RECOMMENDED FOR...
DIRECTIONS FOR USE:
1. Remove any unsound concrete.
2. High-pressure wash the subsurface concrete not more than
24 hours prior installation. Use degreaser as necessary.
Keep all foot and vehicle traffic off pressure washed surfaces.
- Vertical surfaces
- Underwater surfaces
- Substrates other than concrete
3. Lay chalk line
4. Screed into place 3/8” of DriBond™ polymer-modified Portland cement mortar mix over the entire area to be paved.
FEATURES & BENEFITS:
FEATURES
- Advanced, multi-component mixture
- Premixed polymer-modified Portland cement
dry mix mortar.
- Dry-applied
BENEFITS
- Chemist-formulated, proven mixture of polymers,
additives, Portland Cement, and aggregate
- Consistent results, ease-of-use
- Rapid placement, no mixing
TOOLS NEEDED:
- Tape Measure
- Chalk Line
- Heavy-Duty Breaker Hammer
- Wheelbarrow
- Cut-Off Saw
- 36” Hand Screed
- 48 oz. Cross Pein Hammer
- Gauging or Margin Trowel
- Thin-Section Concrete Pavers
-DriBondTM Dry Mis Mortar
- Paver Tech BorderBondTM Liquid Polymer Admix
•
For uneven surfaces or dips consider increasing the recommended coverage rate to a maximum of 1” in thickness (depth)
in order to float or level out the surface.
•
Cover any existing joints or cracks. Small cracks up to ¾”
may be covered with DriBond™ dry mix. Larger sections of
damaged concrete must be cut out to full depth and repaired.
We recommend the use of rebar and concrete in the repair of
full-depth repairs.
•
Install thin-section pavers according to manufacturer’s instructions.
5. Install border pavers using liquid latex modified BorderBond™. Follow the instructions for creating a mortar bed
using Paver Tech BorderBond™ liquid latex admixture.
6. After all pavers are installed according to the manufacturer’s
instructions, apply water for activation from the highest elevation in paver field, continue apply water for cement hydration
by liberally sprinkling the pavers with about ¼” of water per
square foot, in roughly 25 square foot increments. Do NOT
exceed ¼” of water per square foot.
7. Spread mason sand over the pavers and sweep, filling all
paver joints.
8. Repeat the water application step a second time.
9. Allow mortar to hydrate and set for at least 24 hours before
allowing foot traffic or 48 hours before allowing vehicle traffic.
Installs like Sand, Sets like Cement
TM
PATENT PENDING
VERTECH.COM PAVERTECH.COM PAVERTECH.COM PAVERTECH.COM PAVERTECH.COM PAVERTECH.COM
DRiBOND
A revolutionary polymer modified dry mudset.
TECHINICAL DATA:
TYPICAL APPLICATION PROPERTIES
Precipitation
48 hour rain-free forecast
Temperature
Above 40 degrees Fahrenheit for 48 hours
Hydration Water Temperature
Between 40 and 95 degrees Fahrenheit
Initial Set Time (ASTM C308 Hr:Min)
4:26
Final Set Time (ASTM C308 Hr:Min)
5:40
TYPICAL CURED PERFORMANCE PROPERTIES
Compressive Strength (1 Day) ASTM C579
2,930 PSI
Compressive Strength (3 Day) ASTM C579
4,950 PSI
Compressive Strength (28 Day) ASTM C579
6,850 PSI
STORAGE AND DISPOSAL:
DISCLAIMER:
- Store DriBond™ polymer-modified mortar mix in a dry area,
out of direct sunlight. DriBond™ should be protected from
the elements with an opaque tarp on the job site.
The information and recommendations contained herein are
based on our research and years of proven, reliable installations
and are believed to be accurate, but no warranty, express or
implied, is made or should be inferred. Purchasers should test
the products to determine acceptable quality and suitability
for their own intended use. Nothing contained herein shall be
construed to imply the nonexistence of any relevant patents or
to constitute a permission, inducement or recommendation to
practice any invention covered by any patent, without authority
from the owner of the patent.
- Properly dispose of unused mortar mix and
construction waste
LABEL PRECAUTIONS:
- CAUTION: MAY CAUSE SKIN, EYE, AND
RESPIRATORY IRRITATION. MAY CAUSE ALLERGIC
SKIN REACTION. PROLONGED INHALATION MAY
CUASE LUNG DAMAGE AND CANCER. Contains: Portland
cement and crystalline silica. Warning: This product contains
crystalline silica, which is known to the State of California to
cause cancer. Handle with care. Avoid contact with eyes, skin,
and clothing. Do not breathe dust. Wash thoroughly after
handling. KEEP OUT OF REACH OF CHILDREN. FIRST
AID: Eye contact: Immediately flush eyes with water for at
least 15 minutes and call a physician or Poison Control Center.
Skin contact: Wash thoroughly with soap and water.
SHIPPING:
Land and Sea: NOT REGULATED
CONTACT:
- Use OSHA-approved particulate respirator whenever
concrete or DriBond™ dust is present at the work site.
Paver Technologies, LLC
4366 N. U.S. Highway 1
Vero Beach, FL 32967
Phone: 888-767-4777
Website: www.pavertech.com
- FOR MORE INFORMATION, CONSULT THE
DRIBOND™ MATERIAL SAFETY DATA SHEET.
Installs like Sand, Sets like Cement
TM
PATENT PENDING
AVERTECH.COM PAVERTECH.COM PAVERTECH.COM PAVERTECH.COM PAVERTECH.COM PAVERTECH.COM