SARGENT® 1331 DOOR CLOSER INSTALLATION
INSTRUCTIONS WITH FOLLOWING ARM SETS:
(JP10, JPH10); (JPS, JPSH); (JCPS, JCPSH)
Strength Adjustment From Size 1 Through 6.
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY
OR DAMAGE
FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477 or
www.Sargentlock.com
Standard Frame Installation
Closer mounts on opposite to hinge (push) side of door. 1331JP10 Parallel Rigid Non Hold Open arm illustrated.
See Pages 3 and 4
Hinge
Edge
of Door
Hinge
Edge
of Door
Right Hand Door – RH
Left Hand Reverse – LHR
Left Hand Door – LH
Right Hand Reverse – RHR
Narrow Frame Installation
Closer mounts on opposite to hinge (push) side of door. 1331JPS arm illustrated.
125JV and 581-1 accessories required for this application (supplied separately).
Hinge Edge
of Door
Right Hand Door – RH
Left Hand Reverse – LHR
Hinge Edge
of Door
See Pages 3 and 4
Left Hand Door – LH
Right Hand Reverse – RHR
Flush Partition Installation
Closer mounts on opposite to hinge (push) side of door. 1331JCPSH illustrated.
125JVF accessory required for this application (supplied separately).
Hinge Edge
of Door
Right Hand Door – RH
Left Hand Reverse – LHR
Hinge Edge
of Door
See Pages 3 and 4
Left Hand Door – LH
Right Hand Reverse – RHR
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited.
63-8160-6000-999
A8160A
Power
Adjustment
Shaft
Components
Backcheck Valve
Soffit
Plate
582-1 Block
(provided)
Delay Valve
(Optional)
Latch Valve
For Blade Stop
581-1 Spacer
Main Arm
Screw
Sweep Valve
Arm Options
Main Arm
Closer
Arm
Closer
Body
For Frame
or Blade Stop
125JV Bracket
For Flush Partition
125JVF Bracket
Secondary Arm
Screw Pack
Optional
Accessories
Removable Stop
Removable Stop
L
Friction Hold Open Nut
Identify Arm Hand
“R” for Right Hand Door
“L” for Left Hand Door
Riveted Elbow
Thumbturn Hold Open
Riveted Elbow
Riveted Elbow
Riveted Elbow
JP10 Parallel Rigid
JPS Parallel Solid Stop
JPH10 Parallel Rigid
Friction Hold Open
JPSH Parallel Solid Stop
Thumbturn
JCPS and JCPSH Arm Kit - See page 3
Preparation for Fasteners
Fasteners
Door or Frame
Aluminum
or Metal
Self-Drilling Screw
Standard
1/4” - 20 machine screw
Sleeve nuts and bolts
Optional
Through-bolts and
grommet-nuts
Wood
(see Note)
Metal
Hollow
Metal
Drill-Sizes
No drill required
3/16” (4.30 mm)
(pilot hole required)
Drill: #7 (0.201” dia.)
Tap: 1/4” - 20
Note: Pilot hole required when
using self-drilling screws
for wood door/frame
applications.
9/32” (7 mm) through;
3/8” (9.5 mm) door face
opposite to closer
Aluminum
or Wood
3/8” (9.5 mm) through
All
9/32” (7 mm);
3/8” (9.5 mm) dia. x
3/8” (9.5 mm) deep on
door opposite to closer
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited.
63-8160-6000-999
Page 2
A8160A
SARGENT® 1331JCPS and 1331JCPSH
Arm spring stop assembly.
Assembly Instructions
·
·
·
·
JP10 conversion:
Determine hand of arm required and remove appropriate hole cap.
Position spring buffer assembly on soffit plate and using 5/32” hex
wrench provided, thread assembly to soffit plate.
JPS and JPSH conversion:
Remove stop from existing plate using 5/32” wrench provided.
Position spring buffer assembly on soffit plate and thread assembly to
soffit plate using the 5/32” hex wrench.
Spring stop to be used with these arm assemblies:
Plug
Removable Stop
Removable Stop
Thumbturn Hold Open
Soffit Plate
JPSH Arm Assembly
with Thumbturn
Door
(Left Hand Shown)
JPS Arm Assembly
Stop only
Where severe or abusive conditions are expected a
separate door stop, supplied by others, is recommended to
assist in preventing damage to the door closer, closer arm;
or to the door, frame or adjacent walls.
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited.
63-8160-6000-999
Page 3
A8160A
Installation Instructions
Select angle of opening and use dimensions shown on
Page 4 and Dimension Chart below to locate 4 holes on
stop side of door for closer body (or 1331-D drop plate,
only if required, see page 5) and 5 holes on stop and/or
rabbet for Soffit Plate. For applications not covered in
these instructions, a separate template will be required.
· With door closed, closer valves ‘S’ and ‘L’. Then with a
wrench, turn pinion shaft 50° or more to permit proper
alignment of arm mark with pinion flat ‘L’ for Left hand door.
‘R’ for Right hand door.
See Arm Mounting Detail and Main Arm Installation at
right below. (Caution: Closer arm is under spring
tension and may be difficult to rotate.)
· Prepare door and frame for fasteners. See “Preparation
for Fasteners”, Page 2.
· Reopen valves ‘S’ and ‘L’ by turning counter clockwise.
· Set approximate closer power for door size using Power
Adjustment Chart below. Use 5/16" wrench to adjust
Power Adjustment Shaft (set at 8 turns from factory) 20
turns maximum. Turn nut CLOCKWISE to Increase,
COUNTER-CLOCKWISE to Decrease power. See Page
6 for the illustration of this step.
· With door closed, align soffit plate with mounting holes in
frame. Fasten soffit plate to frame with flat head screws
provided.... use spacer blocks 582-1 or 581-1, if required.
(Caution: Closer arm is under spring tension and may
be difficult to rotate.)
· Mount 1331-D Drop plate ... only if required (see Page 5).
· Install closer with power adjustment shaft toward hinge
· Make closer adjustments (see page 6) before installing
cover
NOTE: DO NOT back valves out of closer or a leak will
result.
edge of door.
· For JP10H arm only, check that hand of arm matches
hand of door. See arm illustration on page 2 for location
of arm handing mark.
· Install cover (see page 6).
Arm Mounting Detail
Installation Dimensions Chart
(mm)
B
(mm)
A
(mm)
Center
Pivots
in.
in.
in.
B
(mm)
A
(mm)
B
(mm)
in.
in.
5-1/2 4-3/4
(140) (121)
11 10-1/4
(279) (260)
5-3/8 4-5/8
(137) (117)
10-7/8 10-1/8
(276) (257)
105°110°
110°115°
115°120°
120°180°
2-3/4
(70)
8-1/4
(210)
2-5/8
(67)
8-1/8
(206)
2-1/8
(54)
7-5/8
(194)
2
(51)
7-1/2
(191)
2) Rotate 50°
to here
3) Install arm
here (see below
for details)
Power Adjustment Chart
Main Arm Installation Instructions
Full Clockwise Turns of Closer Power Adjustment Shaft
Door
Size
JP10 / JPH10
37-42 in
33-36 in
0.85-0.9 m 0.95-1.05 m
43-48 in
1.1-1.2 m
Interior
7
10
13
16
Exterior
9
12
15
18
Interior
9
11
13
15
Exterior
10
12
14
16
Power Adjustment Shaft
Pinion Flat
Arm Mark
Y
Right Hand Door
Power Adjustment Shaft
Pinion Flat
S
L
NOTE: Maximum of 20 turns (360°) of Power Adjustment Shaft.
Closer is shipped set at mid power setting.
Door Swing
Left Hand Door
Y
JPS / JPSH
JCP / JCPSH
28-32 in
0.7-0.8 m
1) Start (wrench)
here (bottom
shaft)
1-1/4
(32)
7
(178)
Z
R
Offset
Pivots
4
(102)
9-1/2
(241)
3-7/8
(98)
9-3/8
(238)
3-3/4
(95)
9-1/2
(241)
3-3/8
(86)
8-7/8
(225)
3-1/4
(83)
8-3/4
(222)
in.
A
or
100°105°
Z
JPS
JPSH
JCPS
JCPSH
Butt
Hinges
95°100°
S
JP10
JPH10
90°95°
R
85°90°
Dim
L
·
Arm Mark
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited.
63-8160-6000-999
Page 4
A8160A
Standard Frame
2-3/4
(70)
B
1/2*
(12)
2
(51)
3/8
(10)
2-1/16
(52)
7/16
(11)
1
(25)
Standard
Mount
*Use 9/16 (14) in openings
with blade stops.
C
L Hinge or Pivot
Soffit Plate
A
3-1/8
(79)
5/8 Ref.
(16)
Blade Stop
Mount
Soffit Plate
582-1 Block
581-1 Block
12
(305)
3/4
(19)
Narrow Frame
B
3/8
(10)
1-1/2
(38)
Hinge or
C
L Pivot
3/4
(19)
Notes:
Do Not Scale Drawings.
Left Hand Door Shown in all views.
Same dimensions apply for Right Hand
Dimensions measured from centerline of pivot point.
Dimensions are in inches (mm).
See Page 3 for A & B dimension values.
2-3/4
(70)
2
(51)
7/16
(11)
2 to 2-3/4
(51 to 70)
Frame
Face
1-1/4
(32)
Soffit Plate
125JV Bracket
A
5/8 Ref.
(16)
3-1/8
(79)
Soffit Plate
125JV Bracket
12
(305)
3/4
(19)
Flush Partition
2-1/2
(64)
C
Hinge or C
Pivot L
1/2
(13)
1-1/2
(38)
3/4
(19)
1
(25)
A
3-1/8
(79)
3/4
(19)
63-8160-6000-999
12
(305)
Door
Opening
Dim C
85°
11-1/8 (282.6)
90°
10-3/8 (263.5)
95°
9-5/8 (244.5)
100°
9-0 (228.6)
105°
8-3/8 (212.7)
110°
7-3/4 (197)
581-1 Block
125JVF Angle
Bracket
Soffit Plate
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited.
Page 5
A8160A
1331-D Drop Plate Mounting Holes
Standard Frame
C
L Hinge or Pivot
A
4
(102)
4
(102)
1-1/4
(32)
4
(102)
Soffit
Plate
1331-D Drop Plate
5/16
(8)
Frame Soffit
Narrow Frame
*NOTE: This dimension must be
taken from the same surface that
the Soffit Plate is fastened to.
Hinge or
C
L Pivot
1-1/4*
(32)
A
125JV Bracket
Soffit
Plate
1331-D Drop Plate
4
(102)
Flush Partition
Hinge or
C
L Pivot
A
4
(102)
4
(102)
5/16
(8)
4
(102)
*NOTE: This dimension must be
taken from the surface flush with the
bottom of 125JVF bracket or from the
bottom of the 125JVF bracket.
4
4
1-1/4*
(102)
(102)
(32)
125JVF Bracket
Soffit
Plate
1331-D
Drop Plate
5/16
(8)
Thumbturn Hold-Open Feature (JPSH and JCPSH)
The Thumbturn Hold-Open feature is controlled by the knob
located on the arm of the unit. Turning this knob clockwise will
engage the Hold-Open mechanism and increase the Hold-Open
force. Turning this knob counterclockwise will reduce the HoldOpen force and disengage the Hold-Open mechanism.
DECREASE
Thumbturn Hold Open
Bottom of
125JVF bracket
Friction Hold-Open Feature (JPH10)
Hold door open to opening angle desired and tighten holderadjustment-nut (wrench supplied) or use 1” Box or Open End
wrench.
INCREASE
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited.
63-8160-6000-999
Page 6
A8160A
Unit Adjustment
Closing Power Adjustment
Using “Power Adjustment Chart” from Page 3, select the
correct number of turns for power adjustment shaft that
corresponds with the installation. Rotate adjustment shaft full
360° clockwise turns to desired setting. After closer has been
installed and proper adjustments made to the sweep and
latch, it may be necessary to re-adjust spring power for good
closing action.
Closing Power Control
Figure 1.
Opening Cycle
“Backcheck” valve controls the strength of cushioning in
Backcheck Range. NEVER close this valve completely – it is
not to provide a positive stop. (see Figure 4 and Figure 5).
Opening Door Control
NOTE: Maximum of 20 360° turns
of Power Adjustment Shaft
BACKC
HE
CK
Figure 4.
CAUTION:
DO NOT BACK VALVE OUT OF
CLOSER OR A LEAK WILL
RESULT.
Increase
5/16” Socket
or Adjustable Wrench
Power Adjustment Shaft
Decrease
Opening Cycle
NEVER CLOSE VALVES
COMPLETELY - NOT
INTENDED TO PROVIDE
A POSITIVE STOP.
Backcheck Control
Closing Speed Controls (Figure 2.)
Valve “S” Controls Sweep Range.
Valve “L” Controls Latch Range.
Figure 5.
Increase
Backcheck Valve*
1/8”
Hex
Key
Decrease
Closing Speed Controls
Slow
Figure 2.
Latch
Valve
1/8”
Hex
Key
Sweep
Valve
Fast
Slow
1/8”
Hex.
Key
Cover– Slide cover insert into the un-used cutout in cover.
Install cover using screws provided.
Fast
CAUTION:
DO NOT BACK VALVES OUT OF
CLOSER OR A LEAK WILL
RESULT.
Attention : Adjust Closing Speed Time to
between 4 to 7 seconds from 90°. Use of
the door by handicapped, elderly or
small children may require greater
closing time.
Cover Mounting
Figure 6.
SWEEP
LATCH
10°
CLOSED
Standard Closing Cycle
Copyright © 2013 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing is prohibited.
63-8160-6000-999
Page 7
A8160A