REV_02/10
R
aplicaRev
One-Coat RM
ONE-COAT RENDERING MORTAR
FOR A COMBED FINISH
One-coat rendering and finishing mortar for
decorating and protecting façades. For outdoor use.
OC-CS III-W2 in accordance with Standard UNE-EN
998-1. Spanish Technical Suitability Certificate 503p.
DESCRIPTION
Spanish “DiT Plus”
Certificate
WARNINGS AND
RECOMMENDATIONS
The surfaces must be rough, hard, stable, clean, and free
from dust, paint and release agents.
Brickwork, concrete blocks, thermo-clay, rough M-7.5
mortar renderings and concrete.
Check that the application surface is suitably flat and that no
areas are prone to disintegration. If required, fix the surface
24 hours beforehand, filling in any holes with the same
material. If necessary, repair previously concrete surfaces
with aplicaTec range products.
RENDERING MORTARS
FINISHING
High performance
One-coat rendering and finishing mortar for decorating
and protecting façades.
APPLICATION SURFACES
INSTRUCTIONS FOR USE
1
Check that the surface is suitable and ready
. for use.
2
If mixing mechanically, add water gradually until you obtain a
smooth, lump-free paste of the required consistency.
Alternatively, mix with 7 – 7.5 l of clean water per sack using
an electric mixer at low rpm until you obtain a smooth paste.
.
Apply evenly, then level out the mortar, covering the surface
with a minimum thickness of 10 mm and an average thickness
of 15 mm.
4
Apply
manually or
mechanically
APPLICATIONS
Mortar made with white Portland cement, with inorganic
pigments, screened aggregate of controlled grain size, and
additives which improve the product’s workability, adhesion
and plasticity. Impermeable and mass-coloured, making it
suitable for different types of finish: combed, patterned,
rustic, flattened, textured. Can be applied manually or
mechanically.
3
Medium
combed finish
• Do not apply onto plaster or painted surfaces.
• Do not apply this product when frost or rain are
forecasted as this may lead to efflorescence.
• Do not apply at temperatures below 5ºC or above 35ºC.
• In joints between different materials or where there is a
risk of cracking, reinforce the mortar with a fibreglass
net.
• Apply two coats for thicknesses greater than 20 mm.
• It is advisable to moisten absorbent or very hot surfaces
before applying the product and 24 hours afterwards in
order to prevent the mortar from becoming overly dry or
less strong.
• Do not apply onto waterproofed surfaces.
• If applying to smooth or non-porous surfaces or
concrete, use aplicaRev Fix as an adhesive bridge.
• This product is ready to use mixed with water. Do not
add any kind of additional substance which may alter its
properties.
• Use within 1 year of date of packaging. Store the
product in its original sealed packaging in a dry, covered
place protected from humidity.
Combed Finish. Approximately 6-9 hours later, comb the
surface with a spiked trowel or scratcher. To finish, brush the
surface to eliminate any loose particles.
aplica
FINISHING RENDERING MORTARS
Pág. 136
aplicaRev One-Coat RM
ONE-COAT RENDERING MORTAR FOR A COMBED FINISH
AVAILABLE FORMATS
aplicaRev One-Coat RM is available in 30 kg paper sacks with
moisture-proof plastic lining, dispatched on shrink-wrapped pallets
weighing a total of 1,260 kg (42 sacks).
7 - 7,5 l/sack
Compressive strength
> 5 N/mm2
Flexural strength
> 1,5 N/mm2
Adhesive strength
> 0,4 N/mm2
Capillary action
< 0,2 Kg/m2 min0,5
Mortar density once hardened
1,3 ± 1 Kg/l
Adhesive strength after climate cycles
> 0,4 N/mm2
Water vapour diffusion
14 - 16µ
Water vapour diffusion after climate cycles
0,02 N/ml/cm2 (48 h)
Shrinkage
< 0,6 mm/m
Grain size
< 1,5 mm
Chloride content
< 0,01 %
Consumption
11±1 Kg/m2 per cm
NOTE
The recommendations for use are based on our own knowledge and experience. The technical data provided
have been obtained under normal laboratory conditions, and may therefore vary according to the environmental
conditions in the place where the product is used. As the application conditions are beyond our control, the
information provided here does not imply
that the company accepts responsibility for any variations.
.
aplica
FINISHING RENDERING MORTARS
Pág. 137
RENDERING MORTARS
Mixing water
FINISHING
TECHNICAL FEATURES