SHOWERGLIDE 
SERIES
Installation Instructions
600B, 690B, 692B,
693B, 695B, 697B
IMPORTANT: Yo u s h o u l d c h e c k
with your local plumbing or building
code agency about this product for
compliance before it is installed.
how to care for your door
basic tools and materials needed
TOOLS
Measuring Tape
Hacksaw with 32 teeth per inch blade
Miter Box or Square
Electric Drill
Drill Bit-1⁄8" and 3⁄16"
Masonry Bit for ceramic tile-3⁄16"
Screwdriver-Phillips
Level
Fine File
Pencil
Center Punch
Hammer
Safety Glasses
Caulking Gun
MATERIALS
Caulk
Masking Tape
Mirror panels are made of a
tempered safety glass to
comply with the federal Glazing
Standards. You may notice
some distortion in the mirror as
tempered glass will not reflect
a perfectly true image. This is
an inherent condition found in
all tempered glass mirrors.
NEVER USE SCOURING POWDER, PADS OR SHARP
INSTRUMENTS ON METAL WORK OR GLASS PANELS.
The use of a squeegee following each shower is
recommended to eliminate water spots on the inside of
the glass panels.
An occasional wiping down with a mild detergent diluted
in water is all that is needed to keep the panels and
anodized aluminum parts looking new.
CAUTION: TEMPERED GLASS CANNOT BE CUT.
part names for installation
Wall
Jamb
Top Track
Roller
Wall
Bumper
Handle
Roller Screw
Roller Screw
Handle
Screw
Wall
Jamb
Mounting
Screw
Towel
Bar
Bracket
Roller
Towel Bar
Anchor
Towel
Bar
Bracket
Screw
Wall Jamb
Mounting
Screw
Wall
Bumper
Guide
Screw
Wall
Jamb
Anchor
2
Guide
Bottom
Track
1
MEASURING FOR BOTTOM TRACK
NOTE: If your shower has a curve in
the corners at the side walls, be sure
to measure distance D above curves.
A. Measure distance D at the flattest part
of the tub ledge.
CAUTION: If a steel tape is used, be
sure to add the width of the case to
the measurement.
2
D
CUTTING BOTTOM TRACK
NOTE: Wear Safety Glasses.
A. Cut bottom track 1⁄8" shorter than distance D.
Do not cut top track at this time.
B. F o r b e s t r e s u l t s u s e a 3 2 t o o t h h a c k s a w
blade and a miter box.
3
LOCATING BOTTOM TRACK
A. P l a c e t h e b o t t o m t r a c k o n t h e f l a t t e s t
part of the ledge with the sloping face of
the track towards the inside of the
shower. Make sure that the space
between the wall and track is the same
on both ends.
B. Fasten the track with masking tape. Mark
the ledge with a soft pencil along the
front edge of the track.
NOTE: Track must sit flat. If your ledge
has a curve in the corners at the side
walls or is of fiberglass construction it
may be necessary to shape the ends of
the track with a file.
Bottom
Track
3
4
3⁄16"
DRILLING HOLES
Diameter
Holes
NOTE: Wear Safety Glasses
A. Drill three 3⁄1 6" diameter holes
along the groove at the back
of each wall jamb as shown.
3"
Approximately
2 1⁄2" Off Center
3"
5
LOCATING WALL JAMBS AND
MARKING HOLE LOCATIONS
Wall
Jamb
A. P l a c e o n e w a l l j a m b d o w n o v e r e n d o f
bottom track.
Wall jamb must sit flat against the wall with
legs of wall jamb fully engaged with bottom
t r a c k . NOTE: Y o u m a y n e e d t o s h a p e t h e
bottom ends of jambs to fit units having a
curve at the side walls.
Bottom
Track
Inside of Tub
Wall
Jamb
Level
Pencil
A. Use a level to plumb the wall jamb as shown
and mark the 3 hole locations. Repeat
procedure at opposite end of unit with other
jamb.
Bottom
Track
6
DRILLING HOLES
NOTE: Wear Safety Glasses
A. Remove bottom track. Lightly center punch
the 3-hole locations for each wall jamb. On
ceramic tile, use the center punch to nick
t h e s u r f a c e g l a z e . Ta p t h e p u n c h l i g h t l y
with your hammer so you don’t crack the
tile.
B. Drill all 6 holes with a 3⁄1 6" drill bit (use a
masonry bit for ceramic tile).
C. A f t e r d r i l l i n g , t h o r o u g h l y c l e a n t h e t u b
ledge and insert anchors in all 6 holes.
4
Inside of Tub
7
Caulk
CAULKING BOTTOM TRACK
A. Apply caulk to the caulking grooves on
the underside of the bottom track.
Apply enough to just barely overfill the
grooves. This will give a good seal with
the tub ledge. Install bottom track on
ledge in location marked earlier.
Bottom
Track
B. Seal ends of track at wall with caulk.
TURN OVER BEFORE
INSTALLING ON LEDGE
8
INSTALLING WALL JAMBS
AND BUMPERS
A. Install each wall jamb by inserting over
the bottom track. Align the holes in the
wall jamb with the holes in the wall.
B. Secure the wall jambs with No. 8-18 x
1 1⁄4" panhead screws provided.
Wall Bumper
(Guiding Lip)
Toward Inside
of Shower
C. NOTE: Through the center hole of each
wall jamb, secure a wall bumper with its
guiding lip toward the inside of shower.
Tighten all wall jamb screws.
No. 8-18 x 1 1⁄4"
Panhead Screw
9
Wall
Jamb
MEASURING, CUTTING AND
INSTALLING TOP TRACK
NOTE: Wear Safety Glasses
A. Measure the wall to wall opening at the top of the wall jambs. Cut the
t o p t r a c k 1⁄1 6" s h o r t e r t h a n t h e a c t u a l m e a s u r e m e n t t o a l l o w f o r
clearance. Use a 32 tooth hacksaw blade and a miter box.
CAUTION: If a steel tape is used, be sure to add the width of the
case to the measurement.
B. Install the top track over the wall jamb ends.
5
10
LOCATING AND INSTALLING
BOTTOM TRACK GUIDE
No.
6-32 x 5⁄16"
Flathead
Screw
NOTE: Wear Safety Glasses
A. P l a c e t h e p a n e l g u i d e o n t h e b o t t o m
track exactly midway between the wall
jambs.
B. NOTE: One top edge of the guide fits
into a groove at the front of the track.
Drill a 1⁄8" hole in bottom track through
the hole in the panel guide.
Midway Between
Wall Jambs
C. F a s t e n p a n e l g u i d e w i t h a N o . 6 - 3 2 x
5⁄1 6" flathead screw.
11
INSTALLING ROLLERS
NOTE: The
steel side of
roller must
be installed
against
frame.
No.
8-32 x 3⁄8"
Panhead
Screw
A. Using No. 8-32 x 3⁄8" panhead screws,
assemble two rollers on each panel as
shown. NOTE: The steel side of roller
must be installed against frame.
B. F R O N T P A N E L ---- I n s t a l l t h e r o l l e r s
toward the rough side of glass. Glass
with patterns, install the rollers
opposite the pattern side.
C. I N S I D E P A N E L ----I n s t a l l t h e r o l l e r s
toward the smooth side of glass. Glass
with patterns, install the rollers toward
the pattern side of glass.
(Inside Panel)
Smooth Side
or Pattern
Side
(Front Panel)
Smooth Side
or Pattern
Side
6
12
INSTALLING PANELS
OUTSIDE OR
ROOM SIDE
Inside
Rail
A. Install the inside panel first. Lift it up
inside the top track and hang the rollers
on the inside rail of the top track.
B. Lower the panel bottom frame into the
bottom track panel guide.
C. Slide the inside panel against the wall
jamb on the same side as showerhead.
If the panel does not align with the wall
jamb nearest the shower head, remove
the panel, loosen roller screw(s), move
roller(s) in slot to align door panel,
tighten screw(s), and rehang panel.
Inside
Panel
Bottom Track
Panel Guide
OUTSIDE OR
ROOM SIDE
A. Lift the outside panel up inside the top
track and hang the rollers on the
outside rail of the top track.
Outside
Rail
B. A l i g n w i t h t h e w a l l j a m b o p p o s i t e t h e
showerhead.
C. Adjust rollers if necessary, using same
procedure as for the inside panel.
Outside
Panel
7
13
INSTALLING TOWEL BAR BRACKETS AND TOWEL BAR
(For Series 600B)
Towel Bar
A. Fasten towel bar bracket to each end of
towel bar using No. 8-18 x 3⁄8" binding
head screws.
Towel Bar
Bracket
No. 8-18 x 3⁄8"
Binding Head
Screw
B. Install the towel bar to the outside panel
away from the tub.
C. Use No. 8-18 x 3⁄8" binding head screws
to fasten brackets to the panel frame as
INSTALLING TOWEL BAR BRACKETS AND TOWEL BAR
(For Series 690B, 692B, 693B, 695B and 697B)
Towel Bar
A. Fasten towel bar bracket to each end of
towel bar using No. 8-18 x 3⁄8" flathead
screws.
Towel Bar
Bracket
B. I n s t a l l t h e t o w e l b a r t o t h e o u t s i d e
panel away from the tub.
C. Use No. 8-18 x 3⁄8" flathead screws to
fasten brackets to the panel frame as
shown.
8
No. 8-18 x 3⁄8"
Flathead Screw
14
INSTALLING HANDLE
No. 8-18 x 3⁄8"
Panhead Screw
A. Place one plastic handle on
the inside panel side frame
at the showerhead side.
B. Secure with a No. 8-18 x 3⁄8"
panhead screw.
This Part of
Handle Toward
Inside of Tub
Inside
Panel
Handle
OUTSIDE OR ROOM SIDE
15
CAULKING
CAREFULLY CAULK WHERE:
(A) Wall jambs and wall meet.
(B) Bottom track and wall jamb join.
(C) Bottom track and tub ledge meet.
Allow caulk to set 24 hours before use.
9
parts list
5
15
10
3
10
9
15
4
9
3
9
9
17
8
12
15
15
13
7
3
11
4
3
13
2
3
12
15
6
13 13
16
14
Towel Bar, Towel Bar
Brackets and Screws
for Model 600B-54S 12
12- Towel Bar
Bracket 352701
15
13
3
11-Towel Bar
1
336709
2
13 13- Screw-172817
10
13
11
parts list
Key
No.
When ordering parts, specify model number, part number, quantity and color.
Description
Part Nos. For Door Models
Qty.
600B-54S 690B-54S 690B-59S 692B-59S 693B-59S 695B-59S 697B-59S 690B-59G 697B-59G
1
Bottom Track
1
513314
513301
513301
513301
513301
513301
513301
513355
513355
2
Wall Jamb
2
351606
351612
351612
351612
351612
351612
351612
351625
351625
3
Wall Jamb Mounting Screw----No. 8-18 x 1 1⁄4"
6
456301
456301
456301
456301
456301
456301
456301
456303
456303
4
Wall Bumper
2
517502
517502
517502
517502
517502
517502
517502
517502
517502
5
Top Track
1
477701
477717
477717
477717
477717
477717
477717
477723
477723
6
Front Panel
1
458909
458962
458901
458939
458937
458929
458901
458972
458972
7
Inside Panel
1
458909
458962
458901
458939
458937
458929
458955
458972
458973
8
Plastic Handle
1
581400
581400
581400
581400
581400
581400
581400
581400
581400
9
Roller Screw----No. 8-32 x 3⁄8"
4
456404
456404
456404
456404
456404
456404
456404
456404
456404
10
Roller
4
172818
172818
172818
172818
172818
172818
172818
172818
172818
11
Towel Bar
1
336709
572835
572821
572821
572821
572821
572821
572840
572840
12
Towel Bar Bracket
2
352701
572901
572901
572901
572901
572901
572901
572905
572905
13
Towel Bar Bracket Screw----No. 8-18 x 3⁄8"
4
172817
310121
310121
310121
310121
310121
310121
310122
310122
14
Bottom Track Guide
1
15
Plastic Anchor
6
162217
162217
162217
162217
162217
162217
162217
162217
162217
16
Bottom Track Guide Screw----No. 6-32 x 5⁄16"
1
232104
232104
232104
232104
232104
232104
232104
232104
232104
17
Plastic Handle Screw----No. 8-18 x 3⁄8"
1
456311
456311
456311
456311
456311
456311
456311
456312
456312
S11015.01 S11015.01 S11015.01 S11015.01 S11015.01 S11015.01 S11015.01 S11015.01 S11015.01