PICNIC TABLE – A24652
INSTALLATION AND OPERATING INSTRUCTIONS
Selwood Products
The Granary, Weathercock Hill, Chevington
Bury St. Edmunds, Suffolk IP29 5RG
General Inquiries:
Toll Free: 1-877-966-3738
[email protected]
3404652
Rev 12/29/2010
Parts Identification (Reduced Size)
3631207
(3) Table Top 5/4 x 6 x 411⁄2"
3640468
(2) Seat Support 2 x 3 x 36 ⁄2"
1
3640469
(2) Table Support 2 x 3 x 163⁄4"
3640470
(4) Table Leg 2 x 3 x 261⁄4"
3641213
(2) Table Seat 5/4 x 6 x 36"
(1) Table Rail 2 x 3 x 305⁄8"
3641214
3640889
(2) Picnic Gusset 2 x 3 x 8"
Hardware ID (Actual Size)
(8) Hex Bolt 1/4 x 2-3/4" (9277223)
1/4" Lock Washer – 1/4" Flat Washer – 1/4" T-Nut
(2) Wood Screw #8 x 1-1/2" (9260512)
(22) Wood Screw #8 x 2-1/2" (9260522)
(8) Wood Screw #8 x 3" (9260530)
2
STEP
4A Table Assembly
Table Assembly
(Part 1) (Part 1)
Table End Assembly
A: Attach 1 (B11) Table Support and 1 (B10) Seat
Support to 2 (B12) Table Legs using 2 (H11) 1/4 x 2¾”
hex bolts (with flat washer, lock washer and t-nut) per
board. Make sure (B11) is flush with the top of (B12).
B: Repeat Step A to create a second Table End
Assembly.
Wood Parts
2X B10 Seat Support 2 x 3 x 36½"
2X B11 Table Support 2 x 3 x 16¾"
4X B12 Table Leg 2 x 3 x 26¼"
B11
Hardware
8X H11 Hex Bolt 1/4 x 2¾"
B10
B12
H11
Tighten
Bolts
If end of Bolt
protrudes
beyond
T-nut...
B12
Use extra
Flat Washer
Wood Parts
2X B24 Table Seat 5/4 x 6 x 36"
Hardware
C: With assistance from another adult, place 1 (B24) Table Seat to
each side of the Table End Assembly. Make sure the table is level
before attaching seats. Use 4 (S3) #8 x 2½” wood screws per board.
8X S3 Wood Screw #8 x 2½"
S3
S3
S3
B24
S3
B24
30ǫ"
Table End Assembly
Table End Assembly
18
3
Use Help
Table
(Part 2) (Part 2)
STEP Assembly
4B Table Assembly
Wood Parts
A: Attach 3 (A4) Table Tops to the (B11) Table Support using
4 (S3) #8 x 2½” wood screws per board.
3X A4 Table Top 5/4 x 6 x 41½"
Hardware
S3
12X S3 Wood Screw #8 x 2½"
S3
A4
B11
B11
Wood Parts
1X B25 Table Rail 2 x 3 x 30ǫ"
2X B32 Picnic Gusset 2 x 3 x 8"
Hardware
2X S2 Wood Screw #8 x 1½"
2X S3 Wood Screw #8 x 2½"
8X S4 Wood Screw #8 x 3"
B: With help turn the table upside down. Attach 1 (B32) Picnic
Gusset to each (B11) Table Support using 2 (S4) #8 x 3” wood
screws per gusset. Each gusset should lie flat against the middle
(A4) Table Top.
C: Attach Picnic Gusset to middle Table Top using 1 (S2) #8 x 1½”
and 1 (S3) #8 x 2½” wood screws per gusset.
D: Attach (B25) Table Rail to each (B10) Seat Support using 2 (S4)
#8 x 3” wood screws on each side.
S3
B10
B10
B25
S2
S4
S4
B11
S4
S4
A4
B11
B32
UNDERSIDE VIEW
19
4
B32