An easy way to make precise templates.
BY CARL DUGUAY
Kurvenlinfix Flexible Curved Router
Template Guides
Templates can really speed up your woodworking. They enable you to make identical
convex or concave shaped parts with relative ease. One of the most common ways of
laying out a curve is by using a thin strip of wood or plastic. You secure the two ends of the
strip on top of your template material (such as MDF or Baltic Birch ply), and then
manipulate an intermediate point between the ends to lay out the curve. Then it's off to the
bandsaw to rough cut the template. Next you need to fair (smooth) the bandsawn edge –
this is the most crucial part in making the template – typically done with some combination
of hand plane, spokeshave, rasp, and sandpaper. The edge of the template has to be
smooth and square to it's surface. For some, the process of fairing an edge can be arduous
and frustrating.
The Kurvenlinfix Flexible Curved Router Template Guides offer a quick and easy way to
make precise templates that simplifies the fairing process. Rather than doing all that
smoothing by hand, it's done on a router table.
Kurvenlinfix guides comes in five configurations
The Kurvenlinfix guides are made from a hard, flexible plastic compound. They're available
in five sizes. The 'blue' coloured guides are approximately 3/4" thick, and come in 1m/39",
2m/78", and 3m/118" lengths. There are two 'red' guides – a 1/2" thick guide that
is 1200mm/47" long, and a smaller 5/16 thick guide that is 600mm/24" long. I tried the 1
meter blue guide and both the 600mm and 1200mm red guides.
A series of evenly spaced mounting holes run the length of the guides, enabling you to
attach them to your template. Mounting screws are supplied. If you loose the screws you
can substitute any wood screw of comparable size.
Clamp the guide in place before attaching
There are two ways to use these guides. You can draw a curve directly on the template
using a thin flexible piece of wood, and then align the guide along the drawn line and screw
it in place. I find this method works best for complex curves. For simple concave and
conves curves that aren't too long I find it quicker to align the guide with clamps (see top
photo above), and then secure it with screws. For longer curves I first draw out the curve
on the template, and then, starting at one end of the guide, screw it in place.
Watch out for kinks
One of the issues I found is that it's easy to inadvertently misalign the guide when you're
sinking screws (predominately at the points indicated by the black arrows in the photo
above). Even the slightest misalignment will result in a slight valley or hill along the edge of
the finished template. Make sure you use a low torque/speed setting on your drill/driver,
and maintain firm downward pressure on the guide as you sink the screws.
Bandsaw the waste
Once you've attached the guide it's off to the bandsaw. There is no need to remove the
guide in order to bandsaw the waste – simply bandsaw to about 1/8" from the guide. Slow
and steady.
Rout the template flush to the guide
Using a template bit you can then rout the template flush to the guide. If you were careful to
bandsaw to within 1/8" of the template, you can rout the template in one pass. Otherwise,
take multiple passes to remove the waste. The result is a clean, smooth, curve. Mount your
clamps to the template and it's off to the races.
Templates are quick and easy to make
I find the Kurvenlinfix guides quick and easy to use – noticeably quicker than fairing the
curves by hand. I use curves on almost all my furniture, and these guides certainly reduce
the time it takes to make new templates. I find the 1/2", 1200mm red guide best suited for
the work I do. The 5/16" guide would likley be a better choice for short or compound
curves. The 3/4" guides are more suited for architectural woodworking that involves long
sweeping curves. They're also a better choice if you use a shaper rather than a router
table.
If you only use curved work once in a while, then these guides probably aren't for you.
However, if you do a lot of curved work in your furniture, then a Kurvenlinfix guide is a great
time saver, and will consistently give you perfectly clean, smooth curves.
KEY FEATURES:
Manufactured from a hard, flexible plastic compound.
Hold their shape well without too much spring back.
Available in lengths from 600mm/24" to 3m/118").
Attached with screws (supplied).
COMPANY:
Fisch Tools
MODEL:
Red (mini)
Blue (standard)
Red - 600mm/24"
Red - 1200mm/47"
Blue - 1m/39"
Blue - 2m/78"
Blue - 3m/118"
MADE IN:
Austria
SOURCE:
WoodFrog.ca
ToolsForWoodworking.com
Author:
Carl Duguay
Discover more great woodworking reviews!
Subscribe Now and get instance online access to our library filled with exciting
woodworking information.
Continue to stay connected to the latest tool reviews with our bi-monthly woodworking
magazines!