WAGO-I/O-SYSTEM 750 XTR
Pos : 2 /D okumentati on allgemein/Ei nband/Ei nband H andbuch - Fronts eite 2015 - mit Doc Variabl en (Standar d) @ 9\mod_1285229289866_0.doc x @ 64941 @ @ 1
Manual
750-626/040-000
24V DC Supply Filter (Surge)/HI /XTR
Power Supply Filter for System and
Field-side Power Supply /XTR
Version 1.2.0
Pos : 3 /Alle Serien (Allgemeine M odul e)/Rec htlic hes, Allgemei nes/Impressum für Standardhandbüc her - allg. Angaben, Ansc hriften, T elefonnummer n und E-Mail-Adres sen @ 3\mod_1219151118203_21.doc x @ 21060 @ @ 1
2
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
© 2016 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone:
Fax:
+49 (0) 571/8 87 – 0
+49 (0) 571/8 87 – 1 69
E-Mail:
[email protected]
Web:
http://www.wago.com
Technical Support
Phone:
Fax:
+49 (0) 571/8 87 – 5 55
+49 (0) 571/8 87 – 85 55
E-Mail:
[email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail:
[email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende der Liste für T extmar ke Ei nband_vorne ===
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Table of Contents
3
Pos : 5 /D okumentati on allgemein/Verzeic hnisse/Inhalts verz eichnis - Ü berschrift oG und Verzei chnis @ 3\mod_1219151230875_21.doc x @ 21063 @ @ 1
Table of Contents
1
1.1
1.2
1.3
1.4
1.5
Notes about this Documentation ................................................................. 5
Validity of this Documentation ................................................................. 5
Copyright................................................................................................... 5
Symbols ..................................................................................................... 6
Number Notation ....................................................................................... 8
Font Conventions ...................................................................................... 8
2
Important Notes ........................................................................................... 9
2.1
Legal Bases ............................................................................................... 9
2.1.1
Subject to Changes ............................................................................... 9
2.1.2
Personnel Qualifications ....................................................................... 9
2.1.3
Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions .......................................................................... 9
2.1.4
Technical Condition of Specified Devices ......................................... 10
2.2
Safety Advice (Precautions) .................................................................... 11
3
Device Description ..................................................................................... 13
3.1
View ........................................................................................................ 15
3.2
Connectors............................................................................................... 16
3.2.1
Data Contacts/Internal Bus ................................................................. 16
3.2.2
Power Jumper Contacts/Field Supply ................................................ 17
3.2.3
CAGE CLAMP® Connectors ............................................................. 18
3.3
Display Elements .................................................................................... 19
3.4
Operating Elements ................................................................................. 19
3.5
Schematic Diagram ................................................................................. 20
3.6
Technical Data ........................................................................................ 21
3.6.1
Device ................................................................................................. 21
3.6.2
Supply ................................................................................................. 21
3.6.3
Connection Type ................................................................................ 21
3.6.4
Mechanical Conditions ....................................................................... 22
3.6.5
Climatic Environmental Conditions ................................................... 22
3.7
Approvals ................................................................................................ 23
3.8
Standards and Guidelines ........................................................................ 26
4
Mounting..................................................................................................... 30
4.1
Mounting Sequence ................................................................................. 30
4.2
Inserting and Removing Devices ............................................................ 31
4.2.1
Inserting the I/O Module .................................................................... 31
4.2.2
Removing the I/O Module .................................................................. 32
5
Connect Devices ......................................................................................... 33
5.1
Connecting a Conductor to the CAGE CLAMP® ................................... 33
5.2
Power Supply Concept ............................................................................ 34
5.2.1
Power Supply Units ............................................................................ 35
6
Use in Hazardous Environments .............................................................. 36
6.1
Marking Configuration Examples ........................................................... 37
6.1.1
Marking for Europe According to ATEX and IEC-Ex ...................... 37
6.1.2
Marking for America According to NEC 500 .................................... 42
Manual
Version 1.2.0
4
Table of Contents
6.2
6.2.1
6.2.2
6.2.3
6.2.4
6.2.5
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Installation Regulations ........................................................................... 43
Special Conditions for Safe Use
(TÜV 14 ATEX 148929 X) ................................................................ 44
Special Conditions for Safe Use
(ATEX Certificate TÜV 12 ATEX 106032 X) .................................. 45
Special Conditions for Safe Use
(IEC-Ex Certificate TUN 14.0035X) ................................................. 46
Special Conditions for Safe Use
(IEC-Ex Certificate IECEx TUN 12.0039 X) .................................... 47
Special Conditions for Safe Use according to ANSI/ISA 12.12.01 ... 48
List of Figures ...................................................................................................... 49
List of Tables ........................................................................................................ 50
=== Ende der Liste für T extmar ke Verzeic hnis_vor ne ===
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Notes about this Documentation
Pos : 7 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Übersc hriften/Ebene 1Hinweise z u dies er D okumentation - Ü berschrift 1 @ 4\mod_1237987661750_21.doc x @ 29029 @ 1 @ 1
1
Notes about this Documentation
Pos : 8 /Alle Serien (Allgemeine M odul e)/Sic her heits- und s onstige Hinweise/HinweisHinweis: Dokumentation aufbewahr en @ 4\mod_1237987339812_21.doc x @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos : 9 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Übersc hriften/Ebene 2Gültig keitsbereic h - Ü berschrift 2 @ 12\mod_1338912448776_21.doc x @ 96469 @ 2 @ 1
1.1
Validity of this Documentation
Pos : 10 /Serie 750 ( WAGO-I/O-SYST EM)/Hi nweis e z ur D okumentati on/Gültigkeits bereic h/Gültig keits ber eich Dokumentation Bus kl emme 750- xxxx, ohne Variantenangabe @ 14\mod_1358944037947_21.doc x @ 109346 @ @ 1
This documentation is only applicable to the I/O module 750-626/040-000
(24V DC Supply Filter (Surge)/HI /XTR).
Pos : 11 /Serie 750 ( WAGO-I/O-SYST EM)/Hi nweis e z ur D okumentati on/Hi nweise/Ac htung: Hinweis z ur D okumentati on Bus kl emmen 750- xxxx @ 4\mod_1237986979656_21.doc x @ 29023 @ @ 1
The I/O module 750-626/040-000 shall only be installed and operated according
to the instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos : 12.1 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 2/Ur hebersc hutz - Ü bersc hrift 2 @ 23\mod_1435647042188_21.doc x @ 184808 @ 2 @ 1
1.2
Copyright
Pos : 12.2 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nes /Urhebersc hutz ausführlich @ 4\mod_1235565145234_21.doc x @ 27691 @ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos : 12.3 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
5
6
Notes about this Documentation
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 12.4 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2Symbol e - Ü bersc hrift 2 @ 13\mod_1351068042408_21.doc x @ 105270 @ 2 @ 1
1.3
Symbols
Pos : 12.5.1 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Gefahr/Gefahr: _War nung vor Pers onenschäden allgemei n_ - Erläuter ung @ 13\mod_1343309450020_21.doc x @ 101029 @ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos : 12.5.2 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Gefahr/Gefahr: _War nung vor Pers onenschäden durch el ektrisc hen Strom_ - Erläuterung @ 13\mod_1343309694914_21.doc x @ 101030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos : 12.5.3 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Warnung/Warnung: _Warnung vor Personensc häden allgemei n_ - Erläuterung @ 13\mod_1343309877041_21.doc x @ 101035 @ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos : 12.5.4 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Vorsic ht/Vorsicht: _War nung vor Pers onensc häden allgemein_ - Erläuterung @ 13\mod_1343310028762_21.doc x @ 101038 @ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos : 12.5.5 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Ac htung/Achtung: _War nung vor Sac hsc häden allgemein_ - Erläuterung @ 13\mod_1343310134623_21.doc x @ 101041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos : 12.5.6 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Ac htung/Achtung: _War nung vor Sac hsc häden durc h elektrostatis che Aufladung_ - Erl äuter ung @ 13\mod_1343310227702_21.doc x @ 101044 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos : 12.5.7 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Hi nweis /Hinweis: _Wic htiger Hi nweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.doc x @ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos : 12.5.8 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Infor mation/Infor mation: _Weiter e Infor mation allgemei n_ - Erl äuter ung @ 13\mod_1343310439814_21.doc x @ 101051 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Notes about this Documentation
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos : 12.6 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
7
8
Notes about this Documentation
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 12.7 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 2/D arstellung der Z ahlens ys teme - Ü bers chrift 2 @ 23\mod_1435647128078_21.doc x @ 184811 @ 2 @ 1
1.4
Number Notation
Pos : 12.8 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nes /Zahlens ysteme @ 3\mod_1221059454015_21.doc x @ 21711 @ @ 1
Table 1: Number Notation
Number Code
Decimal
Hexadecimal
Binary
Example
100
0x64
'100'
'0110.0100'
Note
Normal notation
C notation
In quotation marks, nibble separated with
dots (.)
Pos : 12.9 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 2/Sc hriftkonventi onen - Ü bersc hrift 2 @ 23\mod_1435647186005_21.doc x @ 184814 @ 2 @ 1
1.5
Font Conventions
Pos : 12.10 /Alle Serien (Allgemeine M odul e)/Rechtliches, Allgemeines/Sc hriftkonventi onen @ 3\mod_1221059521437_21.doc x @ 21714 @ @ 1
Table 2: Font Conventions
Font Type Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu items are marked in bold letters.
Menu
e.g.: Save
A greater-than sign between two names means the selection of a
>
menu item from a menu.
e.g.: File > New
Designation of input or optional fields are marked in bold letters,
Input
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
Pushbuttons in dialog boxes are marked with bold letters in square
[Button]
brackets.
e.g.: [Input]
Keys are marked with bold letters in square brackets.
[Key]
e.g.: [F5]
Pos : 13 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Important Notes
9
Pos : 14 /All e Seri en (Allgemei ne Module)/Ü berschriften/N eue Ü berschriften/Ebene 1Wic htige Erläuterungen - Ü berschrift 1 @ 4\mod_1241428899156_21.doc x @ 32170 @ 1 @ 1
2
Important Notes
Pos : 15.1 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nes Wic htige Erläuterungen - Einl eitung @ 3\mod_1221059818031_21.doc x @ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos : 15.2 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2R ec htlic he Grundlagen - Ü berschrift 2 @ 3\mod_1221060626343_21.doc x @ 21726 @ 2 @ 1
2.1
Legal Bases
Pos : 15.3 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nes Änderungs vor behalt - Ü berschrift 3 und Inhalt @ 3\mod_1221060036484_21.doc x @ 21720 @ 3 @ 1
2.1.1
Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos : 15.4 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Pers onalqualifi kationPers onalqualifi kation 750- xxxx - Ü bersc hrift 3 und Inhalt @ 3\mod_1224061208046_21.doc x @ 24063 @ 3 @ 1
2.1.2
Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos : 15.5 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Bes timmungsgemäß e Verwendung Bes ti mmungsgemäße Verwendung 750-xxxx - Ü berschrift 3 und Inhal t @ 3\mod_1224064151234_21.doc x @ 24070 @ 3 @ 1
2.1.3
Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description” > “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.
Manual
Version 1.2.0
10
Important Notes
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Appropriate housing (per 2014/34/EU) is required when operating the WAGOI/O-SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos : 15.6 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nesT ec hnis cher Z ustand der Geräte - Übersc hrift 3 und Inhalt @ 3\mod_1221060446109_21.doc x @ 21723 @ 3 @ 1
2.1.4
Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos : 15.7 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Important Notes
11
Pos : 15.8 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2Sicher heits hi nweis e - Ü berschrift 2 @ 6\mod_1260180299987_21.doc x @ 46724 @ 2 @ 1
2.2
Safety Advice (Precautions)
Pos : 15.9 /All e Seri en ( Allgemei ne Module)/Sicherheits- und s ons tige Hi nweis e/Einl eitung Sicherheits hinweis e H ardware @ 6\mod_1260180170493_21.doc x @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos : 15.10.1 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Gefahr /Gefahr: Nicht an Geräten unter Spannung ar beiten! @ 6\mod_1260180365327_21.doc x @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos : 15.10.2 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en/Sic her hei ts- und s onstige Hi nweise/Gefahr/Gefahr: Ei nbau 0750- xxxx nur i n Gehäus en, Sc hränken oder el ektrisc hen Betriebsräumen! @ 6\mod_1260180556692_21.doc x @ 46731 @ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos : 15.10.3 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Gefahr /Gefahr: Unfall verhütungs vorsc hriften beachten! @ 6\mod_1260180657000_21.doc x @ 46735 @ @ 1
Pos : 15.10.4 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Gefahr /Gefahr: Auf normg erec hten Ansc hluss ac hten! @ 6\mod_1260180753479_21.doc x @ 46739 @ @ 1
Pos : 15.11 /Alle Serien (Allgemeine M odul e)/Sic herheits- und sonstige Hinweis e/Vorsic ht/Vorsic ht: H eiße Oberfl äc he allgemein @ 6\mod_1264428115588_21.doc x @ 48610 @ @ 1
Hot surface!
The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.
Pos : 15.12.1 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: Defekte oder besc hädigte Ger äte aus tausc hen! @ 6\mod_1260180857358_21.doc x @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos : 15.12.2 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: Geräte vor kriec henden und is olier enden Stoffen schützen! @ 6\mod_1260181036216_21.doc x @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos : 15.12.3 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: Rei nigung nur mit zul ässigen M aterialien! @ 6\mod_1260181203293_21.doc x @ 46751 @ @ 1
Manual
Version 1.2.0
12
Important Notes
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos : 15.12.4 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: Kei n Kontakts pray verwenden! @ 6\mod_1260181290808_21.doc x @ 46755 @ @ 1
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos : 15.12.5 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: Verpol ung ver mei den! @ 6\mod_1260184045744_21.doc x @ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos : 15.12.6 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: El ektr ostatisc he Entl adung vermeiden! @ 6\mod_1260181364729_21.doc x @ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos : 15.13 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Ac htung/Ac htung: XTR - Is olations prüfungen mit DC durchführen! @ 15\mod_1370843209441_21.doc x @ 122210 @ @ 1
Perform insulation tests with direct current (DC)!
Both the supply voltage and control voltage side are capacitively coupled to the
DIN rail. If the modules are mounted on the DIN rail, application of an AC
voltage between the two potentials can lead to the destruction of the device.
Use only direct current (DC) for insulation testing.
To avoid destroying the device, discharge the device completely before applying
the test voltage again.
Pos : 16 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Device Description
13
Pos : 17 /All e Seri en (Allgemei ne Module)/Ü berschriften/N eue Ü berschriften/Ebene 1Ger ätebesc hrei bung - Ü berschrift 1 @ 3\mod_1233756084656_21.doc x @ 27096 @ 1 @ 1
3
Device Description
Pos : 18.1.1 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Anwendung/SY/Anwendung 750-0626/0040-0000 @ 15\mod_1371541127854_21.doc x @ 123339 @ @ 1
The I/O module 750-626/040-000 (24V DC Supply Filter (Surge)/HI /XTR) is
used to provide supply voltage in a fieldbus node.
It contains a filter and overvoltage protection for 24 V system power supply to the
fieldbus coupler/controller via the CAGE CLAMP® connections and as well as
surge protection for the field power supply via the power jumper contacts.
The WAGO‐I/O-SYSTEM 750 XTR can also be used in shipbuilding applications
and onshore/offshore installations (e.g., platforms, loading facilities). This is
possible via certification under the standards of leading agencies such as
Germanischer Lloyd and Lloyd‘s Register. Proper system operation is ensured
(certified) by using this overvoltage protection module.
The same applies regarding use in substations and/or telecontrol systems and
railway technology. In general, the power supply filter (system and field power)
should also be used for XTR module groups.
Important note!
For shipbuilding certified mode in conjunction with fieldbus couplers/controllers
of the 750 XTR series, the system power supply must be provided via the I/O
module 750-626/040-000. It is optimized for use in systems with insulation
monitoring.
The I/O module 750-626/040-000 is powered via CAGE CLAMP® connectors “4”
(24 V IN) and “8” (0 V IN) for the system power supply and via CAGE CLAMP®
connectors “2”/“6” (24 V IN) and “3”/“7” (0 V IN) for the field power from
external sources.
It makes the 24 V power supply available via:
•
CAGE CLAMP® connectors “1” (24 V OUT) and “5” (0 V OUT) for the
system power supply to the fieldbus coupler/controller
•
The power jumper contacts designed as spring contacts for the field level of
the subsequent I/O modules
Pos : 18.1.2 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Versorg ung/Eins peisung 24 V, 0 V mi t Filter @ 16\mod_1377855148243_21.doc x @ 130324 @ @ 1
Pos : 18.1.3 /Dokumentation allgemei n/Glieder ungs elemente/------Leerz eile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 18.1.4 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/Allgemein/Ver weis auf Kapi tel " Ansc hlüss e" @ 8\mod_1276775378035_21.doc x @ 57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos : 18.1.5 /Dokumentation allgemei n/Glieder ungs elemente/------Leerz eile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 18.1.6 /Serie 750 (WAGO-I/O-SYST EM)/Wichtige Erläuterungen/Sic herheits- und sonstige Hinweis e/Achtung/Achtung: M axi mal er Strom Leistungs kontakte 10 A @ 3\mod_1226499143500_21.doc x @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos : 18.1.7 /Serie 750 (WAGO-I/O-SYST EM)/Wichtige Erläuterungen/Sic herheits- und sonstige Hinweis e/Hinweis/Hi nweis: XTR - Misc hbetrieb XTR/Standar d @ 15\mod_1367496420828_21.doc x @ 118326 @ @ 1
Manual
Version 1.2.0
14
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Mixed operation
Mixed operation (standard/XTR modules) within a node is possible when groups
of modules are electrically isolated on the field side (i.e., electrically isolated
power supply).
Pos : 18.1.8 /Serie 750 (WAGO-I/O-SYST EM)/Wichtige Erläuterungen/Sic herheits- und sonstige Hinweis e/Hinweis/Hi nweis: XTR - Erhöhte Störfes tigkeit @ 15\mod_1367496424993_21.doc x @ 118330 @ @ 1
Increased interference!
For standard-compliant application in substation instrumentation and control,
telecontrol systems, railway technology or shipbuilding certified operation,
field-side power supply filter 750-624/040-001 or power supply filter
750-626/040-000 are generally to be used for XTR module groups.
Pos : 18.1.9 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Ei ns atz ber eich/Ei ns atz ber eich 750- xxxx/040- 000 alle XTR- Koppl er/-Contr oller ohne Einsc hr änkung @ 15\mod_1368425919479_21.doc x @ 119444 @ @ 1
The I/O module can be operated with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750 XTR.
Observe the instructions for mixed operation when used in mixed operation
behind standard fieldbus couplers/controllers.
Pos : 18.2 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Device Description
15
Pos : 18.3 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2Ansicht - Ü bersc hrift 2 @ 4\mod_1240984217343_21.doc x @ 31958 @ 2 @ 1
3.1
View
Pos : 18.4 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansic ht/Sys temkl emmen/Ansicht 750-0626_0040- 0000 @ 15\mod_1371536895545_21.doc x @ 123265 @ @ 1
Figure 1: View
Pos : 18.5 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansic ht/Ansic ht C ageCl amp® _Legende mit LEDs , mit 1 Entrieg elungslasc he @ 15\mod_1370867188922_21.doc x @ 122225 @ @ 1
Table 3: Legend for Figure “View”
Pos. Description
1 Marking possibility with MiniWSB
2 Status LEDs
3 Data contacts
4 CAGE CLAMP® connectors
5 Power jumper contacts
6 Release tab
Pos : 18.6 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
Details See Section
--“Device Description” > “Display Elements”
“Device Description” > “Connectors”
“Device Description” > “Connectors”
“Device Description” > “Connectors”
“Mounting” > “Inserting and Removing
Devices”
16
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 18.7 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2Anschl üss e - Ü berschrift 2 @ 4\mod_1240984262656_21.doc x @ 31961 @ 2 @ 1
3.2
Connectors
Pos : 18.8 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansc hl üsse/Datenkontakte/Kl emmenbus - Ü bersc hrift 3 @ 6\mod_1256294684083_21.doc x @ 43660 @ 3 @ 1
3.2.1
Data Contacts/Internal Bus
Pos : 18.9.1 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ansc hlüsse/Datenkontakte - F eldbus koppler/-c ontroller , Abbildung und Besc hrei bung @ 3\mod_1231771259187_21.doc x @ 26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the internal bus. It
is comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Pos : 18.9.2 /Serie 750 (WAGO-I/O-SYST EM)/Wichtige Erläuterungen/Sic herheits- und sonstige Hinweis e/Achtung/Achtung: Bus kl emmen nic ht auf Gol dfeder kontakte leg en! @ 7\mod_1266318463636_21.doc x @ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos : 18.9.3 /Serie 750 (WAGO-I/O-SYST EM)/Wichtige Erläuterungen/Sic herheits- und sonstige Hinweis e/Achtung/Achtung: ESD - Auf g ute Erdung der Umg ebung ac hten! @ 7\mod_1266318538667_21.doc x @ 50708 @ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos : 18.10 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Device Description
17
Pos : 18.11 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ansc hlüss e/Leistungs kontakte/F eldvers orgung - Ü berschrift 3 @ 6\mod_1256294692864_21.doc x @ 43664 @ 3 @ 1
3.2.2
Power Jumper Contacts/Field Supply
Pos : 18.12.1 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansc hlüss e/Leistungs kontakte 2 LK (F eder) - Einl eitung @ 15\mod_1371724414861_21.doc x @ 123722 @ @ 1
The power supply module 750-626/040-000 has 2 self-cleaning power jumper
contacts that transmit power for the field side. The contacts on the right side of the
power supply module are designed as spring contacts.
Pos : 18.12.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansc hlüss e/Leistungs kontakte 2 LK (F eder) - Abbildung - Standard @ 15\mod_1371548903658_21.doc x @ 123408 @ @ 1
Figure 3: Power Jumper Contacts
Pos : 18.12.3 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansc hlüss e/Leistungs kontakte 2 LK (F eder) - Leg ende @ 15\mod_1371724465179_21.doc x @ 123726 @ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
1
2
Type
Spring contact
Spring contact
Function
Potential feed-in (Uv) for field supply
Potential feed-in (0 V) for field supply
Pos : 18.12.4 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en/Sic her hei ts- und s onstige Hi nweise/Ac htung/Ac htung: Maxi maler Str om Leis tungs kontakte 10 A @ 3\mod_1226499143500_21.doc x @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos : 18.13 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
18
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 18.14 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ansc hlüss e/C AGE C LAMP-Ansc hlüsse - Ü bersc hrift 3 @ 6\mod_1256296337770_21.doc x @ 43674 @ 3 @ 1
3.2.3
CAGE CLAMP® Connectors
Pos : 18.15 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ansc hlüss e/Sys temkl emmen/Anschl üss e 750- 0626 @ 8\mod_1280829049200_21.doc x @ 62014 @ @ 1
Figure 4: CAGE CLAMP® Connectors
Table 5: Legend for Figure “CAGE CLAMP® Connectors”
Designation
24 V OUT
0 V OUT
24 V IN
0 V IN
24 V IN
0 V IN
Connector
1
5
2
6
3
7
4
8
Function
Output system supply voltage 24 V (filtered)
Output system supply voltage 0 V (filtered)
Input field supply voltage 24 V
Input field supply voltage 24 V
Input field supply voltage 0 V
Input field supply voltage 0 V
Input system supply voltage 24 V
Input system supply voltage 0 V
Pos : 18.16 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Device Description
19
Pos : 18.17 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2Anz eigeelemente - Übersc hrift 2 @ 4\mod_1240984390875_21.doc x @ 31964 @ 2 @ 1
3.3
Display Elements
Pos : 18.18 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Anzeig eel emente/Systemkl emmen/Anz eigeelemente 750-0626/0040xxxx (Agn, Cgn) far bneutral @ 15\mod_1371539584530_21.doc x @ 123307 @ @ 1
Figure 5: Display Elements
Table 6: Legend for Figure “Display Elements”
Designation
Status of
operating voltage
–
system
Status of
operating voltage
–
field supply
LED
State
Off
A
C
Green
Off
Green
Function
No 24 V system supply voltage.
24 V system supply voltage.
No 24 V field supply voltage on the
power jumper contacts.
24 V field supply voltage on the
power jumper contacts.
Pos : 18.19 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2Bedienel emente - Übersc hrift 2 @ 4\mod_1239191655456_21.doc x @ 30439 @ 2 @ 1
3.4
Operating Elements
Pos : 18.20 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Bedi enel emente/Bedienelemente Bus kl emme 750- xxxx nicht vorhanden @ 4\mod_1236322031125_21.doc x @ 28063 @ @ 1
The I/O module 750-626/040-000 has no operating elements.
Pos : 18.21 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
20
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 18.22 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2Schematisc hes Sc haltbild - Ü berschrift 2 @ 4\mod_1240984441312_21.doc x @ 31967 @ 2 @ 1
3.5
Schematic Diagram
Pos : 18.23 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Sc hematis che Sc haltbilder/Systemklemmen/Schematisc hes Sc haltbild 750- 0626/0040- 0000 @ 15\mod_1371539621494_21.doc x @ 123331 @ @ 1
Figure 6: Schematic Diagram
Pos : 18.24 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Device Description
21
Pos : 18.25 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2T echnisc he Daten - Ü berschrift 2 @ 3\mod_1232967587687_21.doc x @ 26924 @ 2 @ 1
3.6
Technical Data
Pos : 18.26.1 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/VS ( Vari abl ensteuerung)/Tec hnische D aten Ger ät (VS) - XTR @ 15\mod_1369311215011_21.doc x @ 120260 @ 3 @ 1
3.6.1
Device
Table 7: Technical Data – Device
Width
Height (from upper edge of DIN 35 rail)
Length
Weight
Degree of protection
12 mm
61 mm
100 mm
51 g
IP20
Pos : 18.26.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/VS ( Vari abl ensteuerung)/Tec hnische D aten Vers orgung ( VS) - 062x /T ec hnis che D aten Versorgung (VS) - 062x /XT R @ 16\mod_1373273485487_21.doc x @ 125710 @ 3 @ 1
3.6.2
Supply
Table 8: Technical Data – Supply
Voltage supply
under laboratory conditions
+15 °C … +35 °C
for ambient operating temperature
−40 °C … +55 °C
for ambient operating temperature
+55 °C … +70 °C
Current consumption for
power supply max.
Voltage via power jumper contacts
Current via power jumper contacts max.
Rated surge voltage
1)
Including residual ripple of 15 %
Via CAGE CLAMP® connectors, 24
VDC
18 V … 31.2 V (17.4 V … 31.2 V) 1)
18 V … 28.8 V (17.4 V … 28.8 V) 1)
18 V … 26.4 V (17.4 V … 26.4 V) 1)
1.5 A
24 VDC
10 A
1 kV
Pos : 18.26.3 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/VS ( Vari abl ensteuerung)/Tec hnische D aten Ans chl usstec hni k (VS) @ 16\mod_1373273824961_21.doc x @ 125714 @ 3 @ 1
3.6.3
Connection Type
Table 9: Technical Data – Field Wiring
Wire connection
Cross section
Stripped lengths
CAGE CLAMP®
0.25 mm² … 2.5 mm² / AWG 24 … 14
8 mm … 9 mm / 0.33 in
Table 10: Technical Data – Power Jumper Contacts
Power jumper contacts
Voltage drop at Imax.
Table 11: Technical Data – Data Contacts
Data contacts
Pos : 18.26.4 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/VS ( Vari abl ensteuerung)/Tec hnische D aten M echanische Bedi ngungen (VS) - XTR @ 15\mod_1369387569701_21.doc x @ 120364 @ 3 @ 1
Manual
Version 1.2.0
spring contact, self-cleaning, hard gold
plated
< 1 V at 64 I/O modules
slide contact, self-cleaning, hard gold
plated
22
Device Description
3.6.4
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Mechanical Conditions
Table 12: Technical Data – Mechanical Conditions
Vibration resistance
1)
Max. 5g 1)
Follow the installation instructions
Pos : 18.26.5 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/VS ( Vari abl ensteuerung)/Tec hnische D aten kli matisc he Umweltbedi ngungen (VS) - XTR @ 15\mod_1369387559187_21.doc x @ 120360 @ 3 @ 1
3.6.5
Climatic Environmental Conditions
Table 13: Technical Data – Climatic Environmental Conditions
Operating temperature range
Storage temperature range
Relative humidity 1)
Elevation above sea level
without temperature derating
with temperature derating
max.
1)
−40 °C … +70 °C
−40 °C … +85 °C
95 %
0 m … 2000 m
2000 m … 5000 m:
5000 m
0.5 K per 100 m
Short-term condensation per Class 3K7/IEC EN 60721-3-3 and E DIN 40046-721-3 (except
wind-driven precipitation, water and ice formation)
Pos : 18.27 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Device Description
23
Pos : 18.28 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2Z ulass ungen - Ü bersc hrift 2 @ 3\mod_1224055364109_21.doc x @ 24030 @ 2 @ 1
3.7
Approvals
Pos : 18.29.1 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Zul ass ung en/Infor mati on: Weiter e Informati onen z u Z ulassungen 750- xxxx @ 3\mod_1227190967156_21.doc x @ 25221 @ @ 1
More information about approvals.
Detailed references to the approvals are listed in the document “Overview
Approvals WAGO-I/O-SYSTEM 750”, which you can find via the internet
under: www.wago.com > SERVICES > DOWNLOADS > Additional
documentation and information on automation products > WAGO-I/O-SYSTEM
750 > System Description.
Pos : 18.29.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Zul ass ung en/Allgemein/Z ul ass ungen Bus klemme 750- xxxx Allgemei n, ohne Variantenangabe - Ei nlei tung @ 4\mod_1237460656921_21.doc x @ 28643 @ @ 1
The following approvals have been granted to 750-626/040-000 I/O modules:
Pos : 18.29.3 /Alle Serien (Allgemeine M odul e)/Z ulass ungen/Standar dzul ass ungen/CE (Konfor mitäts kennz eic hnung) @ 3\mod_1224494777421_21.doc x @ 24276 @ @ 1
Conformity Marking
Pos : 18.29.4 /Alle Serien (Allgemeine M odul e)/Z ulass ungen/Standar dzul ass ungen/cU Lus (UL508) @ 3\mod_1224055013140_0.doc x @ 24020 @ @ 1
CULUS
UL508
Pos : 18.29.5 /Alle Serien (Allgemeine M odul e)/Z ulass ungen/Standar dzul ass ungenKC - Korea C ertific ate - Filter @ 20\mod_1406535509777_21.doc x @ 160388 @ @ 1
Korea Certification
MSIP-REM-W43-FTM750
Pos : 18.29.6 /D okumentati on allgemein/Gli ederungsel emente/------Leerzeil e------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 18.29.7 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Zul ass ung en/Ex/Zul ass ung en Bus kl emme 750- xxxx Ex, ohne Vari antenangabe - Einl eitung @ 4\mod_1237191218000_21.doc x @ 28423 @ @ 1
The following Ex approvals have been granted to 750-626/040-000 I/O modules:
Pos : 18.29.8 /Alle Serien (Allgemeine M odul e)/Z ulass ungen/Ex-Z ul ass ungen/cULus/cU Lus ( ANSI/ISA 12.12.01) Cl ass I, Di v2 ABCD T4 @ 3\mod_1224054791812_0.doc x @ 24014 @ @ 1
CULUS
ANSI/ISA 12.12.01
Class I, Div2 ABCD T4
Pos : 18.29.9 /D okumentati on allgemein/Gli ederungsel emente/------Leerzeil e------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 18.29.10 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Z ulas sungen/Ex/Z ul. i n Vor ber eitung Bus klemme 750- xxxx Ex, ohne Variantenangabe - Ei nlei tung @ 7\mod_1274259264803_21.doc x @ 56610 @ @ 1
The following Ex approvals are pending for 750-626/040-000 I/O modules:
Pos : 18.29.11.1 /Alle Seri en (Allgemeine M odule)/Z ul ass ungen/Ex-Z ulass ungen/Sonstige/AT EX allgemei n @ 16\mod_1373352135578_0.doc x @ 125803 @ @ 1
ATEX
Pos : 18.29.11.2 /Alle Seri en (Allgemeine M odule)/Z ul ass ungen/Ex-Z ulass ungen/IECEx (TÜV Nor d)/IECEx allgemein @ 16\mod_1373353532946_0.doc x @ 125807 @ @ 1
IECEx
Pos : 18.29.12 /D okumentation allgemein/Gliederungselemente/------Leerzeile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 18.29.13 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Z ulas sungen/Schi ff/Einl eitungss ätz eZ ulas sungen Bus kl emme 750- xxxx Sc hiff, ohne Variantenangabe - Ei nleitung @ 4\mod_1237190918453_21.doc x @ 28420 @ @ 1
The following ship approvals have been granted to 750-626/040-000 I/O modules:
Pos : 18.29.14 /Alle Seri en (Allgemeine M odule)/Zul ass ung en/Sc hiffs zul ass ung en/GL (Ger manisc her Ll oyd) C at. A, B, C , D ( EMC 1), H @ 15\mod_1370521488638_0.doc x @ 122022 @ @ 1
GL (Germanischer Lloyd)
Cat. A, B, C, D (EMC 1), H
Pos : 18.29.15 /D okumentation allgemein/Gliederungselemente/------Leerzeile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 18.29.16 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Z ulas sungen/Schi ff/Einl eitungss ätz eZ ul. i n Vor ber eitung Bus kl emme 750- xxxx Sc hiff, ohne Variantenangabe - Ei nleitung @ 7\mod_1274259318897_21.doc x @ 56614 @ @ 1
The following ship approvals are pending for 750-626/040-000 I/O modules:
Pos : 18.29.17.1 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/ABS (Americ an Bureau of Shi pping) @ 3\mod_1224055151062_0.doc x @ 24023 @ @ 1
ABS (American Bureau of Shipping)
Pos : 18.29.17.2 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/BSH (Bundes amt für Seesc hifffahrt und H ydrographi e) @ 5\mod_1246341825156_21.doc x @ 36334 @ @ 1
Manual
Version 1.2.0
24
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Federal Maritime and Hydrographic Agency
Pos : 18.29.17.3 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/BV (Bureau Veritas) @ 3\mod_1224492116171_0.doc x @ 24220 @ @ 1
BV (Bureau Veritas)
Pos : 18.29.17.4 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/DNV (D et Nors ke Veritas) Cl ass B @ 3\mod_1224492540562_0.doc x @ 24224 @ @ 1
DNV (Det Norske Veritas)
Class B
Pos : 18.29.17.5 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/KR ( Kor ean R egister of Shi ppi ng) @ 3\mod_1224492806109_0.doc x @ 24232 @ @ 1
KR (Korean Register of Shipping)
Pos : 18.29.17.6 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/LR (Lloyd’s Register) Env. 1, 2, 3, 4 @ 3\mod_1224492890453_0.doc x @ 24236 @ @ 1
LR (Lloyd’s Register)
Env. 1, 2, 3, 4
Pos : 18.29.17.7 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/NKK (Nippon Kaiji Kyokai) @ 3\mod_1224493002656_0.doc x @ 24240 @ @ 1
NKK (Nippon Kaiji Kyokai)
Pos : 18.29.17.8 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/PR S (Pols ki R ejestr Statków) @ 3\mod_1224497273250_0.doc x @ 24295 @ @ 1
PRS (Polski Rejestr Statków)
Pos : 18.29.17.9 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/RINA (Registr o Itali ano N avale) @ 3\mod_1224493078359_0.doc x @ 24244 @ @ 1
RINA (Registro Italiano Navale)
Pos : 18.29.17.10 /Dokumentation allgemei n/Gli eder ungs elemente/------Leerz eile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 18.29.18 /D okumentation allgemein/Gliederungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Device Description
Pos : 18.30 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Zul ass ung en/Sc hiff/Informati on: Weiter e Infor mation z u den Sc hiffs zul ass ung en @ 6\mod_1263206668130_21.doc x @ 47820 @ @ 1
For more information about the ship approvals:
Note the “Supplementary Power Supply Regulations” section for the ship
approvals.
Pos : 18.31 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
25
26
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 18.32 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2N ormen und Ric htlini en - Ü bersc hrift 2 @ 4\mod_1242804031875_21.doc x @ 33646 @ 2 @ 1
3.8
Standards and Guidelines
Pos : 18.33.1 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/N or men und Richtlinien/N or men und Richtlinien Bus klemme 750- xxxx, ohne Variantenangabe - Ei nlei tung @ 7\mod_1274278887584_21.doc x @ 56645 @ @ 1
750-626/040-000 I/O modules meet the following standards and guidelines:
Pos : 18.33.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/N or men und Richtlinien/N or men und Richtlinien XTR - M ec hani k und Kli ma Komponenten-HB @ 18\mod_1394633219581_21.doc x @ 147751 @ @ 1
Table 14: Climatic and Mechanical Environmental Conditions
Standard
Transport
EN 60870-2-2
Test Value
Ct2(2k4) (except precipitation / water /
moisture)
Mechanical Environmental Conditions
EN 60870-2-2
Bm
EN 60721-3-1
1M3
EN 60721-3-3
3M5
EN 60068-2-6
Acceleration 5g
IEC 60068-2-27 Shock
15g, 11 ms, 1000 shocks per axis and
direction, half-sine
25g, 6 ms, 1000 shocks per axis and direction,
half-sine
EN 50155
Random vibration:
EN 61373
Category 1, classes A and B
Shock 5g, 30 ms:
Category 1, classes A and B
*)
Shipbuilding
Ambient categories A … D, H
(5g, 25 Hz … 150 Hz)
Climatic Environmental Conditions
EN 60721-3-1
1K5 (except precipitation and ice formation)
EN 60721-3-3
3K7 (except wind-driven precipitation, water
and ice formation)
EN 60870-2-2
C3 (except wind-driven precipitation and ice
formation)
*)
Shipbuilding
Ambient categories A … D, H
(−40 °C … +70 °C)
*)
The list of ship certifications issued is available in the section “Approvals”.
Pos : 18.33.3 /D okumentati on allgemein/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Device Description
Pos : 18.33.4 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/N or men und Richtlinien/EMV-N or men C ontroll er 750-xxxx/EMV-N ormen Bus kl emme 750- xxxx/0040- 0000, nur Standardversion - Ei nleitung XTR @ 18\mod_1395909426189_21.doc x @ 149708 @ @ 1
The I/O module 750-626/040-000 meets the following EMC standards as these
standards relate to the I/O module:
Pos : 18.33.5 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/N or men und Richtlinien/N or men Störfestig kei t XTR @ 18\mod_1394030613258_21.doc x @ 147348 @ @ 1
Table 15: EMC – Immunity to Interference
Standard
Test Value
Electrostatic Discharge
• EN 61000-4-2
8 kV (contact discharge)
• EN 60255-22-2
8 kV (air discharge)
• IEEE C37.90.3
High-frequency Electromagnetic Fields
• EN 61000-4-3 + A1: + A2
20 V/m (80 MHz … 1 GHz)
• EN 60255-22-3
10 V/m (1 GHz … 3 GHz)
• IEEE C37.90.2
Fast Electrical Transient Disturbances / Burst
• EN 61000-4-4
4 kV
• EN 60255-22-4
• IEEE C37.90.1
Surge Voltage / Surge
• EN 61000-4-5
1 kV (conductor/conductor)
• EN 60255-22-5
2 kV (conductor/ground)
Conducted Disturbances, Induced by High-frequency Fields
• EN 61000-4-6
10 V (150 kHz … 80 MHz)
• EN 60255-22-6
Magnetic Fields With Electrical Frequencies
• EN 61000-4-8
300 A/m continuous / 1000 A/m for 1 s
Pulse-shaped Magnetic Fields
• EN 61000-4-9 + A1
300 A/m
Damped Oscillatory Magnetic Fields
• EN 61000-4-10 + A1
100 A/m
Voltage Dips, Short-term Interruptions and Voltage Fluctuations
• EN 61000-4-11
Standard not applicable
Damped Sinusoidal Oscillations
• EN 61000-4-12
1 kV (conductor/conductor)
2 kV (conductor/ground)
Harmonics and Interharmonics
• EN 61000-4-13 + A1
Standard not applicable
Conducted Asymmetric Disturbances
• EN 61000-4-16 + A1 + A2
30 V continuous
300 V for 1 s
Line Frequency Disturbances
• EN 60255-22-7
Standard not applicable
Alternating Components of the Voltage to DC Line Connections
• EN 61000-4-17+A2
15 %
Manual
Version 1.2.0
27
28
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Table 15: EMC – Immunity to Interference
Standard
Test Value
Damped Oscillatory Waves
• EN 61000-4-18 + A1
1.25 kV conductor/conductor
• EN 60255-22-1
2.5 kV conductor/ground
• IEEE C37.90.1
Voltage Dips, Short-term Interruptions and Voltage Fluctuations to DC Supply
Inputs
• EN 61000-4-29
see section “Power Supply Unit”
• EN 60255-11
Harmonics
• Shipbuilding*)
max. 2 W
DC: 3 Veff,
AC: 10 % to 15th harmonic
10 % … 1 % for 15th to 100th harmonic
1 % for 100th to 200th harmonic
*)
The list of ship certifications issued is available in the section “Approvals”.
Pos : 18.33.6 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/N or men und Richtlinien/N or men Störauss endung XTR @ 18\mod_1394087664442_21.doc x @ 147358 @ @ 1
Table 16: EMC – Emission of Interference
Standard
Test Value *)
Enclosure Emission of Interference
• EN 61000-6-3 + A1
30 dB(µV/m), QP, 30 MHz … 230 MHz
• EN 55022 Class B
37 dB(µV/m), QP, 230 MHz … 1 GHz
70 dB(µV/m), Peak, 1 GHz … 3 GHz
50 dB(µV/m), AV, 1 GHz … 3 GHz
74 dB(µV/m), Peak, 3 GHz … 6 GHz
54 dB(µV/m), AV, 3 GHz … 6 GHz
• EN 61000-6-4 + A1
40 dB(µV/m), QP, 30 MHz … 230 MHz
• EN 60255-26
47 dB(µV/m), QP, 230 MHz … 1 GHz
• EN 55011 + A1 Class A
76 dB(µV/m), Peak, 1 GHz … 3 GHz
• EN 55022 Class A
56 dB(µV/m), AV, 1 GHz … 3 GHz
80 dB(µV/m), Peak, 3 GHz … 6 GHz
60 dB(µV/m), AV, 3 GHz … 6 GHz
**)
• Shipbuilding (EMC 1)
80 dB(µV/m) …50 dB(µV/m), QP,
150 kHz … 300 kHz
50 dB(µV/m) … 34 dB(µV/m), QP,
0.3 MHz … 30 MHz
54 dB(µV/m), QP, 30 MHz … 2 GHz
24 dB(µV/m), QP, 156 MHz … 165 MHz
**)
• Shipbuilding (EMC 2)
80 dB(µV/m) … 50 dB(µV/m), QP,
150 kHz … 30 MHz
60 dB(µV/m) … 54 dB(µV/m), QP,
30 MHz … 100 MHz
54 dB(µV/m), QP, 100 MHz … 2 GHz
24 dB(µV/m), QP, 156 MHz … 165 MHz
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Device Description
29
Table 16: EMC – Emission of Interference
Standard
Test Value *)
Conducted Emission of Interference – Line Connection AC Voltage
• EN 61000-6-3 + A1
Standard not applicable
• EN 55022 Class B
• EN 61000-6-4 + A1
Standard not applicable
• EN 55011 + A1 Class A
Conducted Emission of Interference – Line Connection
• Shipbuilding**) (EMC 1)
96 dB(µV) … 50 dB(µV), 10 kHz … 150 kHz
60 dB(µV) … 50 dB(µV),
150 kHz … 350 kHz
50 dB(µV), 0.35 MHz … 30 MHz
**)
• Shipbuilding (EMC 2)
120 dB(µV) … 69 dB(µV),
10 kHz … 150 kHz
79 dB(µV), 150 kHz … 500 kHz
73 dB(µV), 0.5 MHz … 30 MHz
Conducted Emission of Interference – Line Connection DC Voltage
• EN 61000-6-3 + A1
79 dB(µV) QP, 0.15 MHz … 0.5 MHz
• EN 60255-26
66 dB(µV) AV, 0.15 MHz … 0.5 MHz
• EN 55022 Class A
73 dB(µV) QP, 0.5 MHz … 30 MHz
60 dB(µV) AV, 0.5 MHz … 30 MHz
*)
**)
Pos : 19 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
QP = Quasi Peak Detector; AV = Average Detector
If necessary, please find different data in the section “Approval” (regarding approval for EMC 1
or EMC 2).
30
Mounting
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 20 /All e Seri en (Allgemei ne Module)/Ü berschriften/N eue Ü berschriften/Ebene 1M ontier en - Übersc hrift 1 @ 3\mod_1225446744750_21.doc x @ 24900 @ 1 @ 1
4
Mounting
Pos : 21.1 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/M ontagerei henfolge @ 3\mod_1231770210031_21.doc x @ 25992 @ 2 @ 1
4.1
Mounting Sequence
Fieldbus couplers/controllers and I/O modules of the WAGO-I/O-SYSTEM
750/753 are snapped directly on a carrier rail in accordance with the European
standard EN 50022 (DIN 35).
The reliable positioning and connection is made using a tongue and groove
system. Due to the automatic locking, the individual devices are securely seated
on the rail after installation.
Starting with the fieldbus coupler/controller, the I/O modules are mounted
adjacent to each other according to the project design. Errors in the design of the
node in terms of the potential groups (connection via the power contacts) are
recognized, as the I/O modules with power contacts (blade contacts) cannot be
linked to I/O modules with fewer power contacts.
Pos : 21.2 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Vorsic ht/Vorsicht: Verl etz ungsgefahr durc h s charfkantige M ess er kontakte! @ 6\mod_1256193279401_21.doc x @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos : 21.3 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Achtung/Achtung: Bus kl emmen nur in vorgesehener R eihenfolg e stec ken! @ 6\mod_1256194177073_21.doc x @ 43429 @ @ 1
Insert I/O modules only from the proper direction!
All I/O modules feature grooves for power jumper contacts on the right side. For
some I/O modules, the grooves are closed on the top. Therefore, I/O modules
featuring a power jumper contact on the left side cannot be snapped from the top.
This mechanical coding helps to avoid configuration errors, which may destroy
the I/O modules. Therefore, insert I/O modules only from the right and from the
top.
Pos : 21.4 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Hinweis/Hi nweis: Busabsc hluss XTR nicht vergess en! @ 15\mod_1368426836647_21.doc x @ 119458 @ @ 1
Don't forget the bus end module!
Always plug a bus end module 750-600/040-000 onto the end of the fieldbus
node! You must always use this bus end module at all fieldbus nodes with the
WAGO I/O System 750 XTR fieldbus couplers/controllers to guarantee proper
data transfer.
Pos : 21.5 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Bus klemmen 750xxxx/0040xxxx 4g-5g @ 15\mod_1367558844291_21.doc x @ 118470 @ @ 1
For vibration loads > 4g, observe the following installation instructions:
•
Use pan-head screws or blind rivets at least every 60 mm (12 mm pin
spacing) to secure the DIN rail.
•
Make the open conductor length between strain relief and wire connection
as short as possible.
•
Use the reinforced end stop 249-197.
Pos : 21.6 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Mounting
31
Pos : 21.7 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Geräte einfüg en und entfer nen - Ü berschrift 2 @ 3\mod_1231768483250_21.doc x @ 25950 @ 2 @ 1
4.2
Inserting and Removing Devices
Pos : 21.8 /All e Seri en ( Allgemei ne Module)/Sicherheits- und s ons tige Hi nweis e/Vorsic ht/Vorsicht: H eiß e Oberfläc he allgemei n @ 6\mod_1264428115588_21.doc x @ 48610 @ @ 1
Hot surface!
The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.
Pos : 21.9 /All e Seri en ( Allgemei ne Module)/Sicherheits- und s ons tige Hi nweis e/Ac htung/Achtung: Arbeiten an Ger äten nur s pannungsfr ei durc hführ en! @ 6\mod_1256193963573_21.doc x @ 43426 @ @ 1
Perform work on devices only if they are de-energized!
Working on energized devices can damage them. Therefore, turn off the power
supply before working on the devices.
Pos : 21.10 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Ac htung/Ac htung: XTR nic ht unter -20 °C verdr ahten oder umstec ken @ 15\mod_1367559895186_21.doc x @ 118480 @ @ 1
Observe operating temperature!
XTR I/O modules may be operated below −20 °C, but not wired and/or
reconnected.
Pos : 21.11 /Serie 750 ( WAGO-I/O-SYST EM)/Monti eren/D emonti eren/Bus kl emme einfügen @ 3\mod_1231769726703_21.doc x @ 25989 @ 3 @ 1
4.2.1
Inserting the I/O Module
1.
Position the I/O module so that the tongue and groove joints to the fieldbus
coupler/controller or to the previous or possibly subsequent I/O module are
engaged.
Figure 7: Insert I/O Module (Example)
2.
Manual
Version 1.2.0
Press the I/O module into the assembly until the I/O module snaps into the
carrier rail.
32
Mounting
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Figure 8: Snap the I/O Module into Place (Example)
With the I/O module snapped in place, the electrical connections for the data
contacts and power jumper contacts (if any) to the fieldbus coupler/controller or to
the previous or possibly subsequent I/O module are established.
Pos : 21.12 /Serie 750 ( WAGO-I/O-SYST EM)/Monti eren/D emonti eren/Bus kl emme entfer nen @ 4\mod_1239169375203_21.doc x @ 30334 @ 3 @ 1
4.2.2
Removing the I/O Module
1.
Remove the I/O module from the assembly by pulling the release tab.
Figure 9: Removing the I/O Module (Example)
Electrical connections for data or power jumper contacts are disconnected when
removing the I/O module.
Pos : 22 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Connect Devices
33
Pos : 23 /All e Seri en (Allgemei ne Module)/Ü berschriften/N eue Ü berschriften/Ebene 1Ger äte anschli eßen - Ü berschrift 1 @ 3\mod_1234172889468_21.doc x @ 27460 @ 1 @ 1
5
Connect Devices
Pos : 24 /Serie 750 ( WAGO-I/O-SYST EM)/Ans chli eßen/Leiter an C AGE C LAM P ans chli eßen ( allgemei n) - Übersc hrift 2 und Text @ 3\mod_1225448660171_21.doc x @ 24928 @ 2 @ 1
5.1
Connecting a Conductor to the CAGE CLAMP®
The WAGO CAGE CLAMP® connection is appropriate for solid, stranded and
finely stranded conductors.
Only connect one conductor to each CAGE CLAMP®!
Only one conductor may be connected to each CAGE CLAMP®.
Do not connect more than one conductor at one single connection!
If more than one conductor must be routed to one connection, these must be
connected in an up-circuit wiring assembly, for example using WAGO feedthrough terminals.
1.
For opening the CAGE CLAMP® insert the actuating tool into the opening
above the connection.
2.
Insert the conductor into the corresponding connection opening.
3.
For closing the CAGE CLAMP® simply remove the tool. The conductor is
now clamped firmly in place.
Figure 10: Connecting a Conductor to a CAGE CLAMP®
Pos : 25 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
34
Connect Devices
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 26 /All e Seri en (Allgemei ne Module)/Ü berschriften/N eue Ü berschriften/Ebene 2Einspeisekonz ept - Ü bersc hrift 2 @ 9\mod_1292323902755_21.doc x @ 67445 @ 2 @ 1
5.2
Power Supply Concept
Pos : 27 /Serie 750 ( WAGO-I/O-SYST EM)/Ans chli eßen/Eins peisekonz epte/GL/LR Ei ns peis ekonzept 750- 0624/- 0626/040-000 @ 15\mod_1371533192117_21.doc x @ 123257 @ @ 1
The following shows the power supply concept of a fieldbus node of the WAGOI/O-SYSTEM 750 XTR for certified used according to GL/LR.
Figure 11: Power Supply Concept GL/LR
The 24 V system power supply for the fieldbus coupler/controller must be filtered
and protected against overvoltage with power supply filter 750-626/040-000.
The 24 V field supply voltages must be supplied via field-side power supply filter
750 624/040-001 or power supply filter 750-626/040-000 (protected against
overvoltage).
No filter I/O module is required for a 230 V field power supply.
Pos : 28 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Connect Devices
35
Pos : 29 /Serie 750 ( WAGO-I/O-SYST EM)/Systembesc hr eibung/Vers orgung/Netzgeräte XTR @ 16\mod_1373963895846_21.doc x @ 126216 @ 3 @ 1
5.2.1
Power Supply Units
The WAGO-I/O-SYSTEM 750 XTR requires 24 VDC voltage (system supply)
for operation.
Recommendation
A stable power supply cannot always be assumed everywhere. Therefore, you
should use regulated power supplies to ensure the quality of the supply voltage
(see also table “WAGO power supply units”).
For brief voltage dips, a buffer (200 µF per 1 A load current) must be provided.
Buffer for system power supply!
The system power supply must be buffered to bridge power outages. As the power
demand depends on the respective node configuration, buffering is not
implemented internally.
To achieve power outages of 1 ms to 10 ms according to IEC61131-2, determine
the buffering appropriate for your node configuration and structure it as an
external circuit.
The power demand must be determined individually depending on the entry point
of the field supply. All loads through field devices and I/O modules must be taken
into account. The field supply also impacts the I/O modules because the input and
output drivers of some I/O modules require the voltage of the field supply.
System and field supply must be isolated!
The system supply and field supply must be isolated to ensure bus operation in the
event of short circuits on the actuator side.
Table 17: WAGO Power Supply Units
Item number
Description
787-822/xxx-xxx Primary switch-mode power supply EPSITRON® PRO Power,
24 VDC / 5 A*), nominal input voltage 100 VAC … 240 VAC
787-832/xxx-xxx Primary switch-mode power supply EPSITRON® PRO Power,
24 VDC / 10 A*), nominal input voltage 110 VAC … 240 VAC
787-840/xxx-xxx Primary switch-mode power supply EPSITRON® PRO Power,
24 VDC / 10 A*), nominal input voltage 3×
400 VAC … 500 VAC
*)
Pos : 30 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
Derating −3 %/K > +50 °C
36
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 31.1 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 1Eins atz in expl osionsgefährdeten Bereic hen - Übersc hrift 1 @ 3\mod_1224075191281_21.doc x @ 24084 @ 1 @ 1
6
Use in Hazardous Environments
Pos : 31.2 /Serie 750 (WAGO-I/O-SYST EM)/Eins atz in Ex- Ber eichen/Ei ns atz ber eich Serie 750 @ 3\mod_1234272230203_21.doc x @ 27500 @ @ 1
The WAGO-I/O-SYSTEM 750 (electrical equipment) is designed for use in
Zone 2 hazardous areas.
The following sections include both the general identification of components
(devices) and the installation regulations to be observed. The individual
subsections of the “Installation Regulations” section must be taken into account if
the I/O module has the required approval or is subject to the range of application
of the ATEX directive.
Pos : 31.3 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Use in Hazardous Environments
Pos : 31.4 /Serie 750 (WAGO-I/O-SYST EM)/Eins atz in Ex- Ber eichen/Beis piel hafter Aufbau der Kennz eic hnung - Übersc hrift 2 @ 3\mod_1224157499140_21.doc x @ 24182 @ 2 @ 1
6.1
Marking Configuration Examples
Pos : 31.5 /Serie 750 (WAGO-I/O-SYST EM)/Eins atz in Ex- Ber eichen/Kennz eic hnung für Europa gemäß ATEX und IEC- EX - Übersc hrift 3 @ 3\mod_1224157620203_21.doc x @ 24185 @ 3 @ 1
6.1.1
Marking for Europe According to ATEX and IEC-Ex
Pos : 31.6 /Serie 750 (WAGO-I/O-SYST EM)/Eins atz in Ex- Ber eichen/Beis piel bedruc kung der ATEX- und IEC- Ex-zug elass enen Bus klemmen gemäß C ENELEC und IEC_2013 @ 14\mod_1360569228625_21.doc x @ 111294 @ @ 1
Figure 12: Side Marking Example for Approved I/O Modules According to ATEX and IECEx
Figure 13: Text Detail – Marking Example for Approved I/O Modules According to ATEX and
IECEx.
Manual
Version 1.2.0
37
38
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Table 18: Description of Marking Example for Approved I/O Modules According to ATEX and
IECEx
Printing on Text
TÜV 07 ATEX 554086 X
IECEx TUN 09.0001 X
Dust
II
3D
Ex
tc Dc
IIIC
T 135°C
Mining
I
M2
Ex
d Mb
I
Gases
II
3G
Ex
nA Gc
nC Gc
IIC
T4
Description
Approving authority and certificate numbers
Equipment group: All except mining
Category 3 (Zone 22)
Explosion protection mark
Type of protection and equipment protection
level (EPL):protection by enclosure
Explosion group of dust
Max. surface temperature of the enclosure
(without a dust layer)
Equipment group: Mining
Category: High level of protection
Explosion protection mark
Type of protection and equipment protection
level (EPL): Flameproof enclosure
Explosion group for electrical equipment for
mines susceptible to firedamp
Equipment group: All except mining
Category 3 (Zone 2)
Explosion protection mark
Type of protection and equipment protection
level (EPL): Non-sparking equipment
Type of protection and equipment protection
level (EPL): Sparking apparatus with protected
contacts. A device which is so constructed that
the external atmosphere cannot gain access to the
interior
Explosion group of gas and vapours
Temperature class: Max. surface temperature
135°C
Pos : 31.7 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Use in Hazardous Environments
Pos : 31.8 /Serie 750 (WAGO-I/O-SYST EM)/Eins atz in Ex- Ber eichen/Beis piel bedruc kung der Ex-i- und IEC-Ex-i-zug elas senen Bus klemmen gemäß C ENELEC und IEC _2013 @ 14\mod_1360569320118_21.doc x @ 111298 @ @ 1
Figure 14: Side Marking Example for Approved Ex i I/O Modules According to ATEX and
IECEx.
Figure 15: Text Detail – Marking Example for Approved Ex i I/O Modules According to ATEX
and IECEx.
Manual
Version 1.2.0
39
40
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Table 19: Description of Marking Example for Approved Ex i I/O Modules According to ATEX and
IECEx
Inscription Text
TÜV 07 ATEX 554086 X
IECEx TUN 09.0001X
TÜV 12 ATEX 106032 X
IECEx TUN 12.0039 X
Dust
II
3(1)D
3(2)D
Ex
tc Dc
[ia Da]
[ib Db]
IIIC
T 135°C
Mining
I
M2 (M1)
Ex d Mb
[ia Ma]
I
Description
Approving authority and certificate numbers
Equipment group: All except mining
Category 3 (Zone 22) equipment containing a safety
device for a category 1 (Zone 20) equipment
Category 3 (Zone 22) equipment containing a safety
device for a category 2 (Zone 21) equipment
Explosion protection mark
Type of protection and equipment protection level
(EPL): protection by enclosure
Type of protection and equipment protection level
(EPL): associated apparatus with intrinsic safety
circuits for use in Zone 20
Type of protection and equipment protection level
(EPL): associated apparatus with intrinsic safety
circuits for use in Zone 21
Explosion group of dust
Max. surface temperature of the enclosure (without a
dust layer)
Equipment Group: Mining
Category: High level of protection with electrical
circuits which present a very high level of protection
Explosion protection mark with Type of protection
and equipment protection level (EPL): Flameproof
enclosure
Type of protection and equipment protection level
(EPL): associated apparatus with intrinsic safety
electrical circuits
Explosion group for electrical equipment for mines
susceptible to firedamp
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Use in Hazardous Environments
41
Table 19: Description of Marking Example for Approved Ex i I/O Modules According to ATEX and
IECEx
Gases
II
3(1)G
3(2)G
Ex
nA Gc
[ia Ga]
[ia Gb]
IIC
T4
Pos : 31.9 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
Equipment group: All except mining
Category 3 (Zone 2) equipment containing a safety
device for a category 1 (Zone 0) equipment
Category 3 (Zone 2) equipment containing a safety
device for a category 2 (Zone 1) equipment
Explosion protection mark
Type of protection and equipment protection level
(EPL): Non-sparking equipment
Type of protection and equipment protection level
(EPL): associated apparatus with intrinsic safety
circuits for use in Zone 0
Type of protection and equipment protection level
(EPL): associated apparatus with intrinsic safety
circuits for use in Zone 1
Explosion group of gas and vapours
Temperature class: Max. surface temperature 135°C
42
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 31.10 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Kennz eichnung für Ameri ka gemäß N EC 500 - Übersc hrift 3 @ 3\mod_1224158423187_21.doc x @ 24188 @ 3 @ 1
6.1.2
Marking for America According to NEC 500
Pos : 31.11 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Beispi elbedruc kung gemäß NEC 500_2013 @ 14\mod_1360580302684_21.doc x @ 111353 @ @ 1
Figure 16: Side Marking Example for I/O Modules According to NEC 500
Figure 17: Text Detail – Marking Example for Approved I/O Modules According to NEC 500
Table 20: Description of Marking Example for Approved I/O Modules According to NEC 500
Printing on Text
CL I
DIV 2
Grp. ABCD
Op temp code T4
Description
Explosion protection group (condition of use
category)
Area of application
Explosion group (gas group)
Temperature class
Pos : 31.12 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Use in Hazardous Environments
Pos : 31.13 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Ebene 2Erric htungs bes timmungen - Ü bersc hrift 2 @ 3\mod_1232453624234_21.doc x @ 26370 @ 2 @ 1
6.2
Installation Regulations
Pos : 31.14 /Alle Serien (Allgemeine M odul e)/Ei ns atz i n Ex-Bereic hen/Errichtungsbes timmungen Ei nleitung_2013 @ 14\mod_1360582328318_21.doc x @ 111371 @ @ 1
For the installation and operation of electrical equipment in hazardous areas, the
valid national and international rules and regulations which are applicable at the
installation location must be carefully followed.
Pos : 31.15 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
43
44
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 31.16 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Besonder e Beding ung en für den sic her en Ex- Betrieb gem. AT EX-Z ertifi kat TÜV 14 ATEX 148929_X @ 21\mod_1416995371807_21.doc x @ 169118 @ 3 @ 1
6.2.1
Special Conditions for Safe Use (TÜV 14 ATEX 148929 X)
1.
2.
3.
4.
Pos : 31.17 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
The modules of the WAGO-I/O-SYSTEM 750-*** have to been erected in
such a way, that corresponding to EN 60079-15 a degree of protection of at
least IP 54 according to EN 60529 is achieved.
Measures have to been taken, external to the modules, to provide a transient
protection that ensures that the rated voltage, connected to the power supply
terminals, is not exceeded by more than 40 %.
The connecting and disconnecting of the non-intrinsically safe circuits is
only permitted if no explosive atmosphere exists. This although applies for
the all switches, interfaces (Fieldbus, Ethernet, Serial) and the SD-card.
The ambient temperature range is: 0 °C ≤ Tamb ≤ +60 °C
The ambient temperature range for modules with suffix extension /025-****
is: -20 °C ≤ Tamb ≤ +60 °C
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Use in Hazardous Environments
45
Pos : 31.18 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Besonder e Beding ung en für den sic her en Ex- Betrieb gem. AT EX-Z ertifi kat TÜV 12 ATEX 106032x_2013_2 @ 15\mod_1368620479454_21.doc x @ 119782 @ 3 @ 1
6.2.2
Special Conditions for Safe Use (ATEX Certificate TÜV 12
ATEX 106032 X)
1.
2.
3.
4.
Pos : 31.19 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
For use as Gc- or Dc-apparatus (in zone 2 or 22) the Field bus Independent
I/O Modules WAGO-I/O-SYSTEM 750-*** Ex i shall be erected in an
enclosure that fulfils the requirements of the applicable standards (see the
marking) EN 60079-0, EN 60079-11, EN 60079-15 and EN 60079-31.
For use as group I electrical apparatus M2 the apparatus shall be erected in
an enclosure that ensures a sufficient protection according to EN 60079-0
and EN 60079-1 and the degree of protection IP64.
The compliance of these requirements and the correct installation into an
enclosure or a control cabinet of the devices shall be certified by an ExNB.
Measures have to be taken outside of the device that the rating voltage is not
being exceeded of more than 40 % because of transient disturbances.
The connecting and disconnecting of the non-intrinsically safe circuits is
only permitted during installation, for maintenance or for repair purposes.
The temporal coincidence of explosion hazardous atmosphere and
installation, maintenance resp. repair purposes shall be excluded.
For the type the following shall be considered: The Interface circuits shall
be limited to overvoltage category I/II (non mains/mains circuits) as defined
in EN 60664-1.
46
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 31.20 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Besonder e Beding ung en für den sic her en Ex- Betrieb gem. IEC-Ex-Z ertifi kat TUN 14.0035 X_2014 @ 21\mod_1416995779884_21.doc x @ 169122 @ 3 @ 1
6.2.3
Special Conditions for Safe Use (IEC-Ex Certificate TUN
14.0035X)
1.
2.
3.
4.
Pos : 31.21 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
The modules of the WAGO-I/O-SYSTEM 750-*** have to been erected in
such a way, that corresponding to IEC 60079-15 a degree of protection of at
least IP 54 according to IEC 60529 is achieved.
Measures have to been taken, external to the modules, to provide a transient
protection that ensures that the rated voltage, connected to the power supply
terminals, is not exceeded by more than 40 %.
The connecting and disconnecting of the non-intrinsically safe circuits is
only permitted if no explosive atmosphere exists. This although applies for
the all switches, interfaces (Fieldbus, Ethernet, Serial) and the SD-card.
The ambient temperature range is: 0 °C ≤ Tamb ≤ +60 °C
The ambient temperature range for modules with suffix extension /025-****
is: -20 °C ≤ Tamb ≤ +60 °C
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Use in Hazardous Environments
47
Pos : 31.22 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Besonder e Beding ung en für den sic her en Ex- Betrieb gem. IEC-Ex-Z ertifi kat TUN 12.0039 X_2013_2 @ 15\mod_1368620821493_21.doc x @ 119790 @ 3 @ 1
6.2.4
Special Conditions for Safe Use (IEC-Ex Certificate IECEx
TUN 12.0039 X)
1.
2.
3.
4.
Pos : 31.23 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
For use as Gc- or Dc-apparatus (in zone 2 or 22) the Field bus independent
I/O Modules WAGO-I/O-SYSTEM 750-*** Ex i shall be erected in an
enclosure that fulfils the requirements of the applicable standards (see the
marking) IEC 60079-0, IEC 60079-11, IEC 60079-15, IEC 60079-31.
For use as group I electrical apparatus M2 the apparatus shall be erected in
an enclosure that ensures a sufficient protection according to IEC 60079-0
and IEC 60079-1 and the degree of protection IP64.
The compliance of these requirements and the correct installation into an
enclosure or a control cabinet of the devices shall be certified by an ExCB.
Measures have to be taken outside of the device that the rating voltage is not
being exceeded of more than 40 % because of transient disturbances.
The connecting and disconnecting of the non-intrinsically safe circuits is
only permitted during installation, for maintenance or for repair purposes.
The temporal coincidence of explosion hazardous atmosphere and
installation, maintenance resp. repair purposes shall be excluded.
For the type the following shall be considered: The Interface circuits shall
be limited to overvoltage category I/II (non mains/mains circuits) as defined
in IEC 60664-1.
48
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 31.24 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Errichtungsbesti mmung en AN SI ISA 12.12.01_2013_2_für 750-439, -633, - 663/000-003 @ 21\mod_1417518338537_21.doc x @ 169812 @ 3 @ 1
6.2.5
Special Conditions for Safe Use according to ANSI/ISA
12.12.01
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
“This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D
or non-hazardous locations only.”
“This equipment is to be fitted within tool-secured enclosures only.”
“WARNING Explosion hazard - substitution of components may impair
suitability for Class I, Div. 2.”
“WARNING – Do not disconnect equipment unless power has been
switched off or the area is known to be non-hazardous” has to be placed
near each operator accessible connector and fuse holder.
When a fuse is provided, the following information shall be provided: “A
switch suitable for the location where the equipment is installed shall be
provided to remove the power from the fuse.”
For devices with EtherCAT/Ethernet connectors “Only for use in LAN, not
for connection to telecommunication circuits.”
“WARNING - Use Module 750-642 only with antenna module 758-910.”
For Couplers/Controllers and Economy bus modules only: The instructions
shall contain the following: “The configuration interface Service connector
is for temporary connection only. Do not connect or disconnect unless the
area is known to be non-hazardous. Connection or disconnection in an
explosive atmosphere could result in an explosion.”
Modules containing fuses only: “WARNING - Devices containing fuses
must not be fitted into circuits subject to over loads, e.g. motor circuits.”
Modules containing SD card reader sockets only: “WARNING - Do not
connect or disconnect SD-Card while circuit is live unless the area is known
to be free of ignitable concentrations of flammable gases or vapors.”
The modules 750-439, 750-538, 750-633, 750-663/000-003 shall only be
supplied with 750-606 or 750-625/000-001.
Module 750-538 only “In Hazardous Locations, Non-Incendive only when
installed per Control Drawing No. 750-538”.
Pos : 31.25 /D okumentati on allgemei n/Gli ederungsel emente/------Leerz eile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 31.26 /D okumentati on allgemei n/Gli ederungsel emente/------Leerz eile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 31.27 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Infor mati on: Zer tifizier ungs nachweis @ 7\mod_1274279547729_21.doc x @ 56649 @ @ 1
Additional Information
Proof of certification is available on request.
Also take note of the information given on the operating and assembly
instructions.
The manual, containing these special conditions for safe use, must be readily
available to the user.
=== Ende der Liste für T extmar ke Inhalt_mitte ===
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
List of Figures
49
Pos : 33 /D okumentation allgemei n/Verz eic hniss e/Abbil dungs verz eic hnis - Übersc hrift oG und Verz eichnis @ 3\mod_1219222916765_21.doc x @ 21080 @ @ 1
List of Figures
Figure 1: View ....................................................................................................... 15
Figure 2: Data Contacts ......................................................................................... 16
Figure 3: Power Jumper Contacts ......................................................................... 17
Figure 4: CAGE CLAMP® Connectors................................................................. 18
Figure 5: Display Elements ................................................................................... 19
Figure 6: Schematic Diagram ................................................................................ 20
Figure 7: Insert I/O Module (Example) ................................................................. 31
Figure 8: Snap the I/O Module into Place (Example) ........................................... 32
Figure 9: Removing the I/O Module (Example) ................................................... 32
Figure 10: Connecting a Conductor to a CAGE CLAMP® ................................... 33
Figure 11: Power Supply Concept GL/LR ............................................................ 34
Figure 12: Side Marking Example for Approved I/O Modules According to
ATEX and IECEx ........................................................................................ 37
Figure 13: Text Detail – Marking Example for Approved I/O Modules
According to ATEX and IECEx. ................................................................. 37
Figure 14: Side Marking Example for Approved Ex i I/O Modules
According to ATEX and IECEx. ................................................................. 39
Figure 15: Text Detail – Marking Example for Approved Ex i I/O Modules
According to ATEX and IECEx. ................................................................. 39
Figure 16: Side Marking Example for I/O Modules According to NEC 500 ....... 42
Figure 17: Text Detail – Marking Example for Approved I/O Modules
According to NEC 500................................................................................. 42
Pos : 34 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.2.0
50
List of Tables
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 35 /D okumentation allgemei n/Verz eic hniss e/Tabell enverz eichnis - Übersc hrift oG und Verz eichnis @ 3\mod_1219222958703_21.doc x @ 21084 @ @ 1
List of Tables
Table 1: Number Notation ....................................................................................... 8
Table 2: Font Conventions ...................................................................................... 8
Table 3: Legend for Figure “View” ...................................................................... 15
Table 4: Legend for Figure “Power Jumper Contacts” ......................................... 17
Table 5: Legend for Figure “CAGE CLAMP® Connectors” ................................ 18
Table 6: Legend for Figure “Display Elements” ................................................... 19
Table 7: Technical Data – Device ......................................................................... 21
Table 8: Technical Data – Supply ......................................................................... 21
Table 9: Technical Data – Field Wiring ................................................................ 21
Table 10: Technical Data – Power Jumper Contacts ............................................ 21
Table 11: Technical Data – Data Contacts ............................................................ 21
Table 12: Technical Data – Mechanical Conditions ............................................. 22
Table 13: Technical Data – Climatic Environmental Conditions ......................... 22
Table 14: Climatic and Mechanical Environmental Conditions ........................... 26
Table 15: EMC – Immunity to Interference .......................................................... 27
Table 16: EMC – Emission of Interference........................................................... 28
Table 17: WAGO Power Supply Units ................................................................. 35
Table 18: Description of Marking Example for Approved I/O Modules
According to ATEX and IECEx .................................................................. 38
Table 19: Description of Marking Example for Approved Ex i I/O Modules
According to ATEX and IECEx .................................................................. 40
Table 20: Description of Marking Example for Approved I/O Modules
According to NEC 500................................................................................. 42
=== Ende der Liste für T extmar ke Verzeic hnis_hi nten ===
Manual
Version 1.2.0
WAGO-I/O-SYSTEM 750 XTR
750-626/040-000 24V DC Supply Filter (Surge)/HI /XTR
Pos : 37 /D okumentation allgemei n/Einband/Einband H andbuc h - Leers eite für durc h 2 teilbar e Seitenzahl (Standar ddr uc k) @ 3\mod_1219230851078_0.doc x @ 21123 @ @ 1
Manual
Version 1.2.0
51
Pos : 38 /D okumentation allgemei n/Einband/Einband H andbuc h - R üc kseite 2015 @ 9\mod_1285229376516_21.doc x @ 64944 @ @ 1
WAGO Kontakttechnik GmbH & Co. KG
Postfach 2880 •
D-32385 Minden
Hansastraße 27 •
D-32423 Minden
Phone:
05 71/8 87 – 0
Fax:
05 71/8 87 – 1 69
E-Mail:
[email protected]
Internet:
http://www.wago.com
=== Ende der Liste für T extmar ke Ei nband_hinten ===