Medium Pressure Products
MPI™ Fittings and Valves
6,000 – 15,000 PSI Range
Catalog 4234
February 2012
MPI™ Medium Pressure Fittings
Catalog 4234
Introduction
Advanced Features
Parker Hannifin MPI™ Fittings are engineered and
manufactured to provide secure, tight, and leakresistant connections throughout industry, including
off-shore oil and gas exploration platforms, research
labs, and other facilities that require operating
pressures in the range of 6,000 to 15,000 psi.
Every MPI™ Fitting has the features shown below:
MPI™ Fittings are ideally suited to handle liquids,
gases, or chemicals and can be used on a wide variety
of tubing materials including cold drawn – 1/8 hard
(unannealed) tubing or instrument grade thick-walled
annealed stainless steel. Every Parker MPI™ Fitting is
supplied complete and ready to install.
1
2
3
4
5
1. Front ferrule with corrosion-resistant Parker
Suparcase® forms a tight pressure seal between
the body and ferrule in a second strong mechanical
hold on the tube.
2. Rear ferrule with corrosion-resistant Parker
Suparcase® provides a strong mechanical hold on
the tube.
3. Longer thread area for improved resistance to
pressure and load on the ferrules.
4. Molybdenum disulfide-coated inverted nut helps
prevent galling, provides easier assembly, and
permits multiple remakes.
5. Long tube-support area improves resistance to
vibration and line loads.
WARNING – USER RESPONSIBILITY
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND
PROPERTY DAMAGE.
This document and other information from Parker-Hannifin Corporation, its subsidiaries and authorized distributors provide product or system options for further investigation by users
having technical expertise.
The user, through its own analysis and testing, is solely responsible for making the final selection of the system and components and assuring that all performance, endurance,
maintenance, safety and warning requirements of the application are met. The user must analyze all aspects of the application, follow applicable industry standards, and follow the
information concerning the product in the current product catalog and in any other materials provided from Parker or its subsidiaries or authorized distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or system options based upon data or specifications provided by the user, the user is responsible
for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or systems.
Offer of Sale
The items described in this document are hereby offered for sale by Parker-Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by
the provisions stated in the detailed “Offer of Sale” elsewhere in this document or available at www.parker.com/ipdus.
© Copyright 2011 Parker Hannifin Corporation. All Rights Reserved.
ii
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
Materials and Identification
Assembly
Standard MPI™ Fittings are made of Heat Code
Traceable 316 stainless steel. Tubing and fitting
materials should be selected based on compatibility
with the fluid or gas media.
MPI™ Fittings are installed with standard hand tools.
Each size can be preset with a Parker hydraulic preset
tool. Tube preparation does not require cutting of
threads or tube end “coning.”
Part numbers for MPI™ Fittings use symbols that
identify their style, size, and composition.
Dedication to
Quality
MPI™ Fittings Pressure Ratings
Our resources and vast
product line, is available
through our worldwide
distribution network.
The maximum pressure rating is marked on each
fitting. MPI™ working pressures to be determined
by selected tubing. Please see tables on page 3 for
specific working pressures.
• Size 4 MPI™ end – to 15,000 psi
• Size 6 MPI™ end – to 15,000 psi
• Size 8 MPI™ end – to 15,000 psi
• Size 9 MPI™ end – to 15,000 psi
• Size 12 MPI™ end – to 15,000 psi
• Size 16 MPI™ end – to 12,500 psi
For more information
regarding our products
and services, please
contact your authorized
Parker Instrumentation
Distributor.
Table of Contents
Introduction...................................................................................ii
Visual Index.................................................................................iv
MPI™ Fittings
Typical Raw Materials.............................................................. 1
Tube End Dimension Data....................................................... 1
How To Order........................................................................... 1
Tubing Selection Guide............................................................ 2
Temperature Derating Factors................................................. 2
Maximum Allowable Working Pressure Tables......................... 3
Medium Pressure Fittings........................................................ 5
Gaugeability Tools.................................................................. 23
Medium Pressure Valves
MPN Series Valves................................................................ 24
Over Critical Valves................................................................ 30
Bleed Valve............................................................................ 31
Gauge Valve........................................................................... 31
MPB Series Valves................................................................. 32
MPF Series Filters................................................................. 36
MPC and MPCB Series Check Valves................................... 37
MPR Series Relief Valves...................................................... 38
HB4 Series Ball Valves.......................................................... 39
15,000 PSI, Ultra High Flow Ball Valves................................ 40
Technical Information
Assembly Instructions............................................................ 42
Gaugeability Instructions........................................................ 42
Remake Instructions.............................................................. 42
Hydraulic Preset Tools........................................................... 43
Offer of Sale............................................................................... 47
iii
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
Visual Index
MPI™ Fittings
T7HBT7
MPI™ Tube Port
Connector....................... Page 11
FBMP7
MPI™ Male Connector.......... Page 5
T7HF
MPI™ Tube Stub
to Male NPT Pipe.............. Page 11
XHBMP7
37° Flare to MPI™
Connector......................... Page 5
XHT7
37° Flare to
MPI™ Tube Stub............... Page 12
MP7H2BX
37° Flare Bulkhead
to MPI™ Connector.............. Page 6
X41HT7
High Pressure to
MPI™ Tube Stub............... Page 12
X41HBMP7
High Pressure to
MPI™ Connector................. Page 6
X47HT7
Medium Pressure Port Connector
to MPI™ Tube Stub............ Page 12
X42HT7
Medium Pressure to
MPI™ Tube Stub............... Page 13
X42HBMP7
Medium Pressure to
MPI™ Connector................. Page 7
T7HOA
MPI™ Tube Stub
to Male SAE O-ring............ Page 13
GBMP7
MPI™ to Female
NPT Connector................... Page 7
M40HT7
Type “M” High Pressure
Hose Adapter to MPI™
Tube Stub....................... Page 13
MP7HBA
MPI™ to SAE Male
O-ring Connector................. Page 8
TRBMP7
MPI™ Tube
Stub Reducer................... Page 14
M40HBMP7
Type “M” High Pressure
Hose to MPI™ Connector....... Page 8
T7HG
MPI™ Tube Stub
to Female NPT Pipe...........Page 14
GH2BMP7
MPI™ Bulkhead
to Female NPT................... Page 9
MP7PC
MPI™ Port Connector......... Page 15
HBMP7
MPI™ Union
Connector......................... Page 9
NBMP7
45° MPI™ Union Elbow....... Page 15
WBMP7
MPI™ Bulkhead Union
Connector....................... Page 10
T7NBT7
45° MPI™ Tube
Stub Elbow...................... Page 16
GM7
MPI™ Male End to
Female NPT..................... Page 10
GM7
MPI™ Male End to
High Pressure C&T Port....... Page 10
EBMP7
MPI™ Union Elbow............ Page 16
iv
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
Visual Index (Continued)
KBMP7
MPI™ Union Cross............. Page 21
T7EBT7
MPI™ Tube Elbow............. Page 17
FNMP7
MPI™ Plug...................... Page 22
CBMP7
MPI™ to Male NPT Elbow.... Page 17
FNM7
MPI™ Plug...................... Page 22
JBMP7
MPI™ Union Tee............... Page 18
PNBMP7
MPI™ Cap....................... Page 22
X44HBMP7
X44 Male by MPI™
Connector....................... Page 19
MPFF
MPI™ Front Ferrule ........... Page 22
X44HT7
X44 Male by MPI™
Tube Stub....................... Page 19
MPBF
MPI™ Back Ferrule............ Page 23
M40HX44
Type “M” Male by
X44 Male........................ Page 19
BMP7
MPI™ Nut....................... Page 23
X44 Adapter Assembly
............................... Page 19
Gap Gauge
............................... Page 23
Medium Pressure Valves
RBMP7
MPI™ to NPT Male
Run Tee.......................... Page 20
MP Valve Connection Types.......................................... Page 24
Two Way Inline Valves
............................... Page 25
SBMP7
MPI™ to NPT Male
Branch Tee...................... Page 20
9MP7-MPNLB-T-SS
316SS HT#XXXXX
12,500 PSI
OBMP7
MPI™ to NPT
Female Branch Tee............ Page 21
(The Visual Index is continued on the following page.)
v
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
Visual Index (Continued)
Medium Pressure
Bleed Valve
............................... Page 31
Two Way Angle Valves
............................... Page 26
Medium Pressure
Gauge Valve
............................... Page 31
9MP7-MPNAB-T-SS
316SS HT#XXXXX
12,500 PSI
9MP7-MPNXBI-T-SS
316SS HT#XXXXX
12,500 PSI
Three Way/Two Pressure
Connections
............................... Page 27
HT#XXXXX
Two Way Ball Valves
............................... Page 32
HT#XXXXX
9MP7-MPBLPKH-V-SSP
316SS HT#XXXXX
12,500 PSI
HT#XXXXX
Three Way Ball Valves
............................... Page 33
HT#XXXXX
9MP7-MPNXBO-T-SS
316SS HT#XXXXX
12,500 PSI
HT#XXXXX
9MP7-MPBXPK-V-SSP
316SS HT#XXXXX
12,500 PSI
Three Way/One Pressure
Connection
............................... Page 27
HT#XXXXX
9MP7-MPNXBD-T-SS
316SS HT#XXXXX
12,500 PSI
9MP7-MPFL-40-SS
316SS HT#XXXXX
12,500 PSI
HT#XXXXX
Inline Filters
............................... Page 36
HT#XXXXX
9MP7-MPCBL-5-SS
316SS HT#XXXXX
12,500 PSI
Ball Check Valves
............................... Page 37
HT#XXXXX
9MP7-MPCL-5-V-SS
316SS HT#XXXXX
12,500 PSI
Poppet Check Valves
............................... Page 37
Three Way/Two Stem
Connection
............................... Page 28
Relief Valves (Factory Set)
............................... Page 38
HB4 Series Ball Valves
............................... Page 39
9MP7-MPNABR-T-SS
316SS HT#XXXXX
12,500 PSI
Two Way Angle Valves
(Replaceable Seat)
............................... Page 28
15,000 PSI,
Ultra High Flow
Ball Valves.................... Page 40
Technical Information
Hydraulic Preset Tools................................................. Page 43
Over Critical Valves
............................... Page 30
9MP7-MPNLB-T-SS
316SS HT#XXXXX
12,500 PSI
vi
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
Typical Raw Material Specifications
Stainless Steel
(Type 316) (1)
Inches
Bar Stock
Forging
Size Tube
No. O.D.
ASME/ASTM SA/A-479 ASME SA-182 316
BS970 316-S31
Type 316-SS
DIN 4401
AStm A-276
Type 316
BS970 316-S31
DIN 4401
4
6
8
9
10
12
16
(1) If additional information, including heat code traceability, is
required, contact Parker Hannifin or your nearest MPI™ Fitting
distributor.
(2) Parker MPI™ Fittings work reliably on cold drawn - 1/8 hard
tubing (both MPI™ and Cone & Thread), and fully annealed,
heavy wall type 316 tubing. See page 3 for more information
about tubing.
1/4
3/8
1/2
9/16
5/8
3/4
1
Straight
Thread
C
D
E
*L
W Hex
1/2 - 20
5/8 - 20
13/16 - 20
7/8 - 20
15/16 - 20
1 1/8 - 18
1 7/16 - 18
.50
.63
.69
.75
.75
.88
1.13
1.34
1.58
1.85
1.91
2.02
2.26
2.88
.13
.25
.31
.38
.44
.52
.69
1.62
1.88
2.25
2.25
2.43
2.75
3.38
9/16
11/16
15/16
1
1 1/16
1 1/4
1 1/2
*L - Recommended Straight Length of Circular Un-bent Tubing
Dimensions in inches are for reference only, subject to change.
How To Order MPI™ Fittings
Dimensions in inches are for reference only, subject to change.
Parker MPI™ Fittings should be ordered using the part number as listed in this catalog.
Part numbers are developed as follows:
1.A combination of letters and numbers identifies the size and style of the fitting and the material used.
2.Tube and pipe thread sizes are designated by the number of sixteenths of an inch (1/4" tube = 4/16” or 4).
All standard MPI™ Fittings are manufactured from 316 stainless steel. Other materials are available upon special
order.
Straights and Elbows: Specify the largest end of
the MPI first, followed by the smaller tube end OR
pipe thread size.
Tees:
Example:
Part number 9-6-6 JBMP7 would have the
following specifications:
Example:
Part number 4-4 HBMP7 union would have the
specifications listed below.
9-6-6 JBMP7
1
2
4-4 HBMP7
4 - 4
1/4"
Tube
H
B
Shape
Designator,
Union
1/4"
Tube
MP7- SS
3
Medium
Pressure
Inverted
Assembled
with Nut and
Ferrules
9
- 6
9/16"
Tube
(1)
Stainless
Steel
- 6
3/8"
Tube
(3)
3/8"
Tube
(2)
J
B
MP7 - SS
Assembled
with Nut and
Ferrules
Shape
Designator,
Tee
Stainless
Steel
Medium
Pressure
Inverted
Customer Requests: When special configurations are required, please provide a blueprint of the
installation to Parker with your request for a price quote.
Cryogenic Service: MPI™ fittings for cryogenic applications include a vent hole to prevent pressure
build-up in front of the threads. To order “vented” MPI™ parts, add “-VT” to the end of the standard part
number (e.g., 6-6 HBMP7-SS becomes 6-6 HBMP7-SS-VT).
1
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Fittings
Basic Fitting
Material
Tube End Dimensional Data
MPI™ Medium Pressure Fittings
Catalog 4234
Tubing Selection Guide
General Selection Criteria
MPI™ Fittings
Although Parker’s MPI™ Fittings are engineered and
manufactured to consistently provide high levels of
reliability, no system’s integrity is complete without
considering the critical link: tubing.
The data tables in this section will help you select the
tubing that best satisfies the needs of the application.
The most important consideration in the selection of
suitable tubing for any application is the compatibility
of the tubing materials with the media to be contained.
This section is intended to help you properly select
and order quality tubing, both annealed and mediumpressure cold drawn – 1/8 hard (unannealed).
System Pressure
Parker believes that proper tubing selection and
installation are key to building leak-free, reliable tubing
systems.
The system operating pressure is another important
factor in determining the type, and more importantly,
the size of tubing to be used. In general, high
pressure installations require strong materials such as
stainless steel.Tube fitting assemblies should never
be pressurized beyond the recommended working
pressure.
Parker’s MPI™ Fittings have been designed to operate
on a wide variety of “medium pressure” applications
(6,000 to 15,000 psi).
Temperature Derating Factors
Table 1 indicates derating factors for 316 stainless steel tubing and MPI™ fittings at elevated temperatures.
Table 1
Temperature Derating Factors (316 Stainless Steel Tubing)
°F -425 to 100
200
300
400
500
600
700
800
900
1000
°C
-254 to 38
93
149
204
260
316
371
427
482
538
1/8 Hard*
1.000
1.000
1.000
0.960
0.885
0.835
0.795
0.770
0.750
0.740
Annealed**
1.000
1.000
1.000
0.965
0.895
0.850
0.815
0.795
0.775
0.765
* Use with 1/8 Hard 316 tubing shown in Tables 2 and 3 on page 3.
** Use with Annealed 316 tubing shown in Table 4 on page 3.
The rating at temperature is the room temperature (RT) pressure rating listed in the catalog multiplied by the
Derating Factor at temperature.
Example: 1/4" MPI™ fittings and tubing @ 800°F
Room Temperature Working Pressure
= 15,000 psi (as shown in Table 2)
800°F Temperature Derating Factor
= .770 (1/8 Hard tube) (as shown above)
800°F Working Pressure
= 15,000 x .770 = 11,550 psi
2
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
Tables 2, 3 and 4 list the maximum suggested working pressure of various tubing sizes, according to material.
Acceptable tubing diameters and wall thicknesses are those for which a rating is listed. Combinations which do
not have a pressure rating are not recommended for use with MPI™ Fittings.
MPI™ Tubing
MPI™ tubing is marked “MPI” and is designed to provide optimum performance for MPI™ fittings. MPI™ tubing is
nominal OD ± .003") 316 seamless stainless steel, cold drawn – 1/8 hard (unannealed) tubing. Tensile strength is
approximately 40% higher than annealed tubing.
Table 2 – 316 Stainless Steel (Seamless / Unannealed – 1/8 Hard)
Tube
Size
(in.)
Nominal
OD
(in.)
Nominal
ID
(in.)
Working
Pressure
(psi)
1/4
.250
.125
15,000
4-240 MPITube-SS-15K
3/8
.375
.219
15,000
6-240 MPITube-SS-15K
9/16
.562
.344
15,000
9-240 MPITube-SS-15K
3/4
.750
.469
15,000
12-240 MPITube-SS-15K
1
1.000
.656
12,500
16-240 MPITube-SS-12K
MPI™
Tube Part No.
NOTE: Working pressures calculated using an allowable stress of 35,000 psi for 1/8 hard 316 stainless steel
tubing with a minimum tensile strength of 105,000 psi.
NOTE: Sizes 3/4" & 1" require hydraulic presetting
when used with MPI™ fittings.
*Consult factory for pressure tables regarding other
materials.
Dimensions in inches are for reference only, subject to change.
Cone & Thread Tubing
Cone & Thread (C&T) tubing is available as 1/8 hard 316 seamless stainless steel tubing and is designed to work
with existing C&T fittings. C&T tubing has an undersized OD by as much as .010" to better facilitate the coning
and threading operations required for use with C&T fittings. MPI™ fittings work effectively with C&T tubing as
listed below but require hydraulic presetting for optimum performance.
Table 3 – 316 Stainless Steel (Undersized OD, Seamless / Unannealed – 1/8 Hard)
Tube
Size
(in.)
Maximum
OD
(in.)
Nominal
ID
(in.)
Working
Pressure
(psi)
Tube
Size
(in.)
Maximum
OD
(in.)
Nominal
ID
(in.)
Working
Pressure
(psi)
1/4
.250
.109
12,500
9/16
.562
.359
10,000
3/8
.375
.203
12,500
3/4
.750
.516
10,000
9/16
.562
.312
12,500
1
1.000
.688
10,000
Dimensions in inches are for reference
only, subject to change.
Instrumentation Grade Heavy Wall Tubing
Table 4 – 316 Stainless Steel (Seamless / Annealed)
Tube Wall Thickness (in.)
Tube
Size
(in.)
.065
.083
1/4
10,300
13,300
3/8
6,600
8,600
10,000
11,700
6,700
7,800
9,100
1/2
3/4
1
.095
.109
.120
.134
.156
.188
.220
Working Pressure (psi)
5,800
NOTE: Working pressures calculated
using an allowable stress of 20,000
psi for annealed 316 stainless steel
tubing with a nominal O.D. tolerance
of ± .005".
Dimensions in inches are for reference only,
subject to change.
10,000
11,400
6,400
7,300
8,600
10,600
4,700
5,300
6,200
7,700
3
9,200
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Fittings
Maximum Allowable Working Pressure Tables
Notes
Catalog 4234
MPI™ Fittings
4
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
FBMP7
Inches
MPI™ to Male
NPT Connector
Parker
Part No.
"A"
A
"D"
D
"W"
W
HEX
Hex
4-2 FBMP7
4-4 FBMP7
4-6 FBMP7
4-8 FBMP7
6-4 FBMP7
6-6 FBMP7
6-8 FBMP7
8-6 FBMP7
8-8 FBMP7
9-6 FBMP7
9-8 FBMP7
10-8 FBMP7
12-8 FBMP7
12-12 FBMP7
16-12 FBMP7
16-16 FBMP7
"B"
B
FBMP7
NPT
NPT
THREADS
Threads
MPI™
NPT
Size Thread
1/4
1/4
1/4
1/4
3/8
3/8
3/8
1/2
1/2
9/16
9/16
5/8
3/4
3/4
1
1
1/8 - 27
1/4 - 18
3/8 - 18
1/2 - 14
1/4 - 18
3/8 - 18
1/2 - 14
3/8 - 18
1/2 - 14
3/8 - 18
1/2 - 14
1/2 - 14
1/2 - 14
3/4 - 14
3/4 - 14
1 - 11.5
A
B
D
W
Hex
1.91
2.10
2.00
2.17
2.43
2.43
2.48
2.85
2.81
2.91
3.04
3.03
3.85
3.46
4.53
4.58
.38
.57
.57
.76
.57
.57
.76
.57
.76
.57
.76
.76
.76
.76
.76
.95
1.03
1.03
.93
.91
1.24
1.24
1.10
1.60
1.37
1.59
1.53
1.52
2.21
1.82
2.64
2.50
5/8
5/8
3/4
7/8
3/4
3/4
7/8
1
1
1 1/16
1 1/16
1 3/16
1 3/8
1 3/8
1 3/4
1 3/4
Working
Pressure
(PSIG)
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
10,000
10,000
10,000
Dimensions in inches are for reference only, subject to change.
XHBMP7
37° Flare to MPI™ Connector
Inches
Parker
Part No.
4-4 XHBMP7
4-6 XHBMP7
4-8 XHBMP7
4-9 XHBMP7
4-10 XHBMP7
6-4 XHBMP7
6-6 XHBMP7
6-8 XHBMP7
6-9 XHBMP7
8-6 XHBMP7
8-8 XHBMP7
8-9 XHBMP7
8-10 XHBMP7
8-12 XHBMP7
16-16 XHBMP7
37O Flare
Adapter
MPI™
Size
A
B
D
1/4
1/4
1/4
1/4
1/4
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
1
1/4
3/8
1/2
9/16
5/8
1/4
3/8
1/2
9/16
3/8
1/2
9/16
5/8
3/4
1
2.08
2.54
2.90
2.96
3.14
1.97
2.24
2.90
2.97
2.34
2.69
2.77
3.13
3.38
4.23
.55
.55
.55
.55
.55
.56
.56
.56
.56
.66
.66
.66
.66
.86
.91
1.03
1.37
1.66
1.66
1.84
.92
1.06
1.66
1.66
1.06
1.34
1.36
1.72
1.63
2.19
T
Thread
7/16 - 20
7/16 - 20
7/16 - 20
7/16 - 20
7/16 - 20
9/16 - 18
9/16 - 18
9/16 - 18
9/16 - 18
3/4 - 16
3/4 - 16
3/4 - 16
3/4 - 16
1-1/16 - 12
1-5/16 - 12
W
Hex
Working
Pressure
(PSIG)
5/8
3/4
1
1 1/16
1 3/16
5/8
3/4
1
1 1/16
13/16
1
1 1/16
1 3/16
1 3/8
1 3/4
15,000
15,000
15,000
15,000
15,000
12,500
12,500
12,500
12,500
12,500
12,500
12,500
15,000
12,500
7,200
Dimensions in inches are for reference only, subject to change.
5
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Fittings
MPI™ Medium Pressure Fittings
Catalog 4234
MPI™ Medium Pressure Fittings
Catalog 4234
MP7H2BX
37° Flare Bulkhead to
MPI™ Connector
MPI™ Fittings
Inches
Parker
Part No.
4-4 MP7H2BX
6-6 MP7H2BX
8-8 MP7H2BX
9-8 MP7H2BX
MPI™
Size
37° Flare
Adapter
1/4
3/8
1/2
9/16 1/4
3/8
1/2
1/2
A
2.76
3.24
3.44
3.76
C
H
Max
T
Thread
WLN
Hex
W
Hex
Working
Pressure
(PSIG)
1.53
1.93
1.97
2.29
.40
.48
.50
.50
7/16 - 20
9/16 - 18
3/4 - 16
3/4 - 16
11/16
13/16
1
1
5/8
3/4
1
1 1/16
15,000
12,500
12,500
12,500
T
Thread
W
Hex
Working
Pressure
(PSIG)
5/8
3/4
13/16
13/16
1 1/16
1 3/16
1 3/16
1 3/16
1 3/8
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
* Bulkhead hole approximately 1/64" (.015") larger than thread major diameter.
Dimensions in inches are for reference only, subject to change.
X41HBMP7
High Pressure to
MPI™ Connector
Inches
Parker
Part No.
High Pressure
Adapter
MPI™
Size
A
B
D
4-4 X41HBMP7
4-6 X41HBMP7
6-4 X41HBMP7
6-6 X41HBMP7
6-9 X41HBMP7
9-6 X41HBMP7
9-9 X41HBMP7
9-10 X41HBMP7
9-12 X41HBMP7
1/4
1/4
3/8
3/8
3/8
9/16
9/16
9/16
9/16
1/4
3/8
1/4
3/8
9/16
3/8
9/16
5/8
3/4
2.25
2.71
2.52
2.92
3.37
3.12
3.58
3.69
4.03
.72
.72
.92
.92
.92
1.13
1.13
1.13
1.13
1.03
1.37
1.10
1.37
1.70
1.37
1.70
1.81
2.02
9/16 - 18
9/16 - 18
3/4 - 16
3/4 - 16
3/4 - 16
1 1/8 - 12
1 1/8 - 12
1 1/8 - 12
1 1/8 - 12
Dimensions in inches are for reference only, subject to change.
6
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
X42HBMP7
Inches
Parker
Part No.
4-4 X42HBMP7
4-6 X42HBMP7
4-9 X42HBMP7
6-4 X42HBMP7
6-6 X42HBMP7
6-8 X42HBMP7
6-9 X42HBMP7
9-4 X42HBMP7
9-6 X42HBMP7
9-8 X42HBMP7
9-9 X42HBMP7
9-10 X42HBMP7
9-12 X42HBMP7
12-9 X42HBMP7
12-12 X42HBMP7
12-16 X42HBMP7
Medium Pressure
Adapter
MPI™
Size
A
B
1/4
1/4
1/4
3/8
3/8
3/8
3/8
9/16
9/16
9/16
9/16
9/16
9/16
3/4
3/4
3/4
1/4
3/8
9/16
1/4
3/8
1/2
9/16
1/4
3/8
1/2
9/16
5/8
3/4
9/16
3/4
1
2.34
2.80
3.31
2.47
2.93
3.28
3.44
2.56
2.85
3.16
3.41
3.54
4.20
3.55
4.15
5.27
.81
.81
.81
.94
.94
.94
.94
1.13
1.13
1.13
1.13
1.13
1.13
1.31
1.31
1.31
T
Thread
D
1.03
1.37
1.75
1.03
1.37
1.65
1.75
.93
1.10
1.35
1.54
1.66
2.19
1.35
1.96
2.83
7/16 - 20
7/16 - 20
7/16 - 20
9/16 - 18
9/16 - 18
9/16 - 18
9/16 - 18
13/16 - 16
13/16 - 16
13/16 - 16
13/16 - 16
13/16 - 16
13/16 - 16
3/4 - 14 NPS
3/4 - 14 NPS
3/4 - 14 NPS
W
Hex
Working
Pressure
(PSIG)
5/8
3/4
1-1/16
3/4
3/4
1
1-1/16
7/8
7/8
1
1-1/16
1 3/16
1-3/8
1-1/16
1-3/8
1-3/4
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
12,500
Dimensions in inches are for reference only, subject to change.
GBMP7
MPI™ Female
NPT Connector
Inches Working
Parker MPI™NPT
W Pressure
Part No.
Size
Thread
A
D
Hex
(PSIG)
4-2 GBMP7
4-4 GBMP7
4-6 GBMP7
4-8 GBMP7
6-2 GBMP7
6-4 GBMP7
6-6 GBMP7
6-8 GBMP7
8-4 GBMP7
8-6 GBMP7
8-8 GBMP7
9-4 GBMP7
9-6 GBMP7
9-8 GBMP7
10-8 GBMP7
12-8 GBMP7
1/4
1/4
1/4
1/4
3/8
3/8
3/8
3/8
1/2
1/2
1/2
9/16
9/16
9/16
5/8
3/4
1/8 - 27
1/4 - 18
3/8 - 18
1/2 - 14
1/8 - 27
1/4 - 18
3/8 - 18
1/2 - 14
1/4 - 18
3/8 - 18
1/2 - 14
1/4 -18
3/8 - 18
1/2 - 14
1/2 - 14
1/2 - 14
2.06
2.25
2.35
2.58
2.37
2.56
2.66
2.87
2.89
2.99
3.20
2.68
2.93
3.26
3.26
3.70
1.56
1.75
1.85
2.08
1.74
1.93
2.03
2.24
2.20
2.30
2.51
2.18
2.30
2.51
2.51
2.82
13/16
1
1 1/8
1 3/8
13/16
1
1 1/8
1 3/8
1
1 1/8
1 3/8
1 3/8
1 1/8
1 3/8
1 3/16
1 3/8
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
Dimensions in inches are for reference only, subject to change.
7
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Fittings
Medium Pressure to
MPI™ Connector
MPI™ Medium Pressure Fittings
Catalog 4234
MP7HBA
MPI™ to SAE Male
O-Ring Connector
MPI™ Fittings
Inches
Parker
Part No.
4-4 MP7HBA
4-6 MP7HBA
4-8 MP7HBA
6-4 MP7HBA
6-6 MP7HBA
6-8 MP7HBA
8-4 MP7HBA
8-6 MP7HBA
8-8 MP7HBA
9-6 MP7HBA
9-8 MP7HBA
MPI™
Size
SAE*
End
A
B
D
1/4
1/4
1/4
3/8
3/8
3/8
1/2
1/2
1/2
9/16
9/16
1/4
3/8
1/2
1/4
3/8
1/2
1/4
3/8
1/2
3/8
1/2
1.90
1.94
1.97
2.41
2.20
2.23
2.81
2.82
2.60
2.89
2.89
.43
.47
.55
.43
.47
.55
.43
.47
.55
.47
.55
.97
.97
.91
1.35
1.10
1.05
1.69
1.66
1.36
1.67
1.59
T
Thread
7/16 - 20
9/16 - 18
3/4 - 16
7/16 - 20
9/16 - 18
3/4 - 16
7/16 - 20
9/16 - 18
3/4 - 16
9/16 - 18
3/4 - 16
W
Hex
5/8
11/16
7/8
3/4
3/4
7/8
1
1
1
1 1/16
1 1/16
Working
Pressure
(PSIG)
12,500
12,500
12,500
12,500
12,500
12,500
12,500
12,500
12,500
12,500
12,500
*All male o-ring ends for MPI™ fittings are heavy duty and comply with SAE J1926-2. This end has maximum thread engagement for strength and requires the
minimum full thread engagement specified in SAE J1926 for the female port. Standard O-ring material is Nitrile #N0552-90.
Dimensions in inches are for reference only, subject to change.
M40HBMP7
Type “M” High Pressure Hose
to MPI™ Connector
Inches
Parker
Part No.
6-4 M40HBMP7
6-6 M40HBMP7
8-6 M40HBMP7
8-8 M40HBMP7
8-9 M40HBMP7
10-4 M40HBMP7
10-6 M40HBMP7
11-8 M40HBMP7
11-9 M40HBMP7
11-12 M40HBMP7
16-16 M40HBMP7
HOSE*
Adapter
- 6
- 6
- 8
- 8
- 8
- 10
- 10
- 11
- 11
-11
- 16
MPI™
Size
1/4
3/8
3/8
1/2
9/16
1/4
3/8
1/2
9/16
3/4
1
A
2.03
2.45
2.57
2.90
2.97
2.39
2.72
2.89
2.95
3.59
3.88
B
D
.50
.50
.63
.63
.63
.75
.75
.63
.63
.63
.63
1.03
1.32
1.32
1.59
1.59
1.14
1.34
1.58
1.58
2.08
2.13
T
Thread
9/16 - 18
9/16 - 18
3/4 - 16
3/4 - 16
3/4 - 16
7/8 - 14
7/8 - 14
1 - 12
1 - 12
1 - 12
1-5/16 - 12
W
Hex
5/8
3/4
13/16
1
1-1/16
15/16
15/16
1-1/16
1-1/16
1-3/8
1-3/4
Working
Pressure
(PSIG)
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
12,500
* Adapts to Type “M” Swivel Hose Connection.
Dimensions in inches are for reference only, subject to change.
8
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
GH2BMP7
MPI™ Fittings
MPI™ Bulkhead to
Female NPT Connector
Inches
Parker
Part No.
MPI™
Size
NPT
Thread
A
4-4 GH2BMP7
6-8 GH2BMP7
6-12 GH2BMP7
8-12 GH2BMP7
9-4 GH2BMP7
1/4
3/8
3/8
1/2
9/16
1/4 - 18
1/2 - 14
3/4 - 14
3/4 - 14
1/4 - 18
2.38
3.13
3.19
3.50
2.82
D
H
Max.
R
Thread
1.88
2.50
2.56
2.81
2.07
.56
.63
.63
.75
.63
3/4 - 20
7/8 - 20
7/8 - 20
1-1/8 - 20
1-1/8 - 20
T
W
Hex
Working
Pressure
(PSIG)
.75
1.25
1.31
1.31
.69
1
1-3/8
1-1/2
1-1/2
1-3/8
15,000
15,000
10,000
10,000
15,000
Working
Pressure
(PSIG)
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
12,500
* Bulkhead hole approximately 1/64" (.015") larger than thread major diameter.
Dimensions in inches are for reference only, subject to change.
HBMP7
MPI™ Union Connector
Inches
Parker
Part No.
4-4 HBMP7
6-4 HBMP7
6-6 HBMP7
8-4 HBMP7
8-6 HBMP7
8-8 HBMP7
9-4 HBMP7
9-6 HBMP7
9-8 HBMP7
9-9 HBMP7
10-10 HBMP7
12-6 HBMP7
12-9 HBMP7
12-12 HBMP7
16-16 HBMP7
MPI™
Size
A
D
W
Hex
1/4
3/8 - 1/4
3/8
1/2 - 1/4
1/2 - 3/8
1/2
9/16 - 1/4
9/16 - 3/8
9/16 - 1/2
9/16
5/8
3/4 - 3/8
3/4 - 9/16
3/4
1
2.88
3.32
3.44
3.88
4.01
4.07
3.95
4.07
4.13
4.20
4.42
4.76
5.15
5.08
6.52
1.88
2.19
2.19
2.70
2.70
2.70
2.70
2.70
2.70
2.70
2.92
3.25
3.51
3.31
4.25
5/8
3/4
3/4
1
1
1
1-1/16
1-1/16
1-1/16
1-1/16
1 3/16
1-3/8
1-3/8
1-3/8
1-3/4
Dimensions in inches are for reference only, subject to change.
9
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
WBMP7
MPI™ Bulkhead Union
Connector
Inches
Parker
Part No.
MPI™ Fittings
4-4 WBMP7
6-6 WBMP7
8-8 WBMP7
8-9 WBMP7
9-8 WBMP7
9-9 WBMP7
12-12 WBMP7
16-16 WBMP7
MPI™
Size
A
1/4
3/8
1/2
1/2 - 9/16
9/16 - 1/2
9/16
3/4
1
2.88
3.44
4.07
4.20
4.20
4.20
5.08
6.52
D
H
Max
1.88
2.19
2.70
2.70
2.70
2.70
3.31
4.25
.88
1.07
1.32
1.32
1.32
1.32
1.56
2.00
T
*R
Threads
W
Hex
Working
Pressure
(PSIG)
.50
.56
.69
.69
.69
.69
.88
1.13
3/4-20
7/8-20
1 1/8-20
1 1/8-20
1 1/8-20
1 1/8-20
1 7/16-18
1 7/8-12
1
1 1/8
1 3/8
1 3/8
1 3/8
1 3/8
1 7/8
2 1/2
15,000
15,000
15,000
15,000
15,000
15,000
15,000
12,500
* Bulkhead hole approximately 1/64" (.015") larger than thread major diameter.
Dimensions in inches are for reference only, subject to change.
GM7
MPI™ Male End
to Female NPT
Inches
Parker
Part No.
4-4 GM7
4-6 GM7
6-4 GM7
6-6 GM7
6-8 GM7
8-4 GM7
8-6 GM7
8-8 GM7
9-4 GM7
9-6 GM7
9-8 GM7
12-4 GM7
12-6 GM7
12-8 GM7
MPI™
Male
Thread1
1/4
1/4
3/8
3/8
3/8
1/2
1/2
1/2
9/16
9/16
9/16
3/4
3/4
3/4
Female
NPT
End
1/4
3/8
1/4
3/8
1/2
1/4
3/8
1/2
1/4
3/8
1/2
1/4
3/8
1/2
A
B
NPT
Thread
1.73
1.83
1.84
1.94
2.17
2.05
2.15
2.37
2.05
2.15
2.37
2.17
2.17
2.59
.85
.95
.85
.95
1.17
.85
.95
1.17
.85
.95
1.17
.75
.75
1.17
1/4 - 18
3/8 - 18
1/4 - 18
3/8 - 18
1/2 - 14
1/4 - 18
3/8 - 18
1/2 - 14
1/4 - 18
3/8 - 18
1/2 - 14
1/4 - 18
3/8 - 18
1/2 - 14
W
Hex
Working
Pressure
(PSIG)
1
1 1/8
1
1 1/8
1 3/8
1
1 1/8
1 3/8
1
1 1/8
1 3/8
1 1/4
1 1/4
1 3/8
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
¹Assemble 1/4 to 1/2 turn from finger tight & lubricate threads & taper before each remake.
Dimensions in inches are for reference only, subject to change.
GM7
MPI™ Male End
to High Pressure C&T Port
Inches
Parker
Part No.
4-4HF GM7
6-4HF GM7
6-6HF GM7
8-4HF GM7
8-6HF GM7
9-4HF GM7
9-6HF GM7
12-4HF GM7
12-6HF GM7
MPI™
High
Male Press C&T
Thread1
Port
1/4
3/8
3/8
1/2
1/2
9/16
9/16
3/4
3/4
1/4
1/4
3/8
1/4
3/8
1/4
3/8
1/4
3/8
A
B
C&T
Thread
1.57
1.68
1.87
1.89
2.07
1.89
2.07
2.17
2.30
.69
.69
.88
.69
.88
.69
.88
.75
.88
9/16 - 18
9/16 - 18
3/4 - 16
9/16 - 18
3/4 - 16
9/16 - 18
3/4 - 16
9/16 - 18
3/4 - 16
W
Hex
3/4
3/4
1
15/16
1
1
1
1 1/4
1 1/4
Working
Pressure
(PSIG)
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
¹Assemble 1/4 to 1/2 turn from finger tight & lubricate threads & taper before each remake.
Dimensions in inches are for reference only, subject to change.
10
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
T7HBT7
MPI™ Tube Port Connector
Inches
Tube
Size
L
Parker
Part No.
* 4 T7HBT7-SS
4 T7HBT7-SS 4.0
4 T7HBT7-SS 6.0
4 T7HBT7-SS 8.0
4 T7HBT7-SS 10.0
4 T7HBT7-SS 12.0
* 6 T7HBT7-SS
6 T7HBT7-SS 4.0
6 T7HBT7-SS 6.0
6 T7HBT7-SS 8.0
6 T7HBT7-SS 10.0
6 T7HBT7-SS 12.0
* 9 T7HBT7-SS
9 T7HBT7-SS 6.0
9 T7HBT7-SS 8.0
9 T7HBT7-SS 10.0
9 T7HBT7-SS 12.0
* 12 T7HBT7-SS
12 T7HBT7-SS 6.0
12 T7HBT7-SS 8.0
12 T7HBT7-SS 10.0
12 T7HBT7-SS 12.0
1/4
1/4
1/4
1/4
1/4
1/4
3/8
3/8
3/8
3/8
3/8
3/8
9/16
9/16
9/16
9/16
9/16
3/4
3/4
3/4
3/4
3/4
Working
Pressure
(PSIG)
2.72
4.00
6.00
8.00
10.00
12.00
3.19
4.00
6.00
8.00
10.00
12.00
3.85
6.00
8.00
10.00
12.00
4.55
6.00
8.00
10.00
12.00
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
MPI™ Fittings
Catalog 4234
Assemble 1/2 turn from finger tight.
* Same Assembled Length as MP7PC.
Dimensions in inches are for reference only, subject to change.
T7HF
MPI™ Tube Stub
to Male NPT Pipe
Inches
Parker
Part No.
MPI™
Tube Stub
Male
NPT End
A
4-4 T7HF
4-6 T7HF
4-8 T7HF
6-4 T7HF
6-6 T7HF
6-8 T7HF
8-4 T7HF
8-6 T7HF
8-8 T7HF
9-4 T7HF
9-6 T7HF
9-8 T7HF
9-12 T7HF
12-8 T7HF
12-12 T7HF
1/4
1/4
1/4
3/8
3/8
3/8
1/2
1/2
1/2
9/16
9/16
9/16
9/16
3/4
3/4
1/4
3/8
1/2
1/4
3/8
1/2
1/4
3/8
1/2
1/4
3/8
1/2
3/4
1/2
3/4
2.32
2.44
2.76
2.56
2.68
2.99
2.82
2.95
3.26
2.88
3.01
3.32
3.43
3.67
3.80
B
NPT
Thread
W
Hex
Working
Pressure
(PSIG)
.57
.57
.76
.57
.57
.76
.57
.57
.76
.57
.57
.76
.76
.76
.76
1/4 - 18
3/8 - 18
1/2 - 14
1/4 - 18
3/8 - 18
1/2 - 14
1/4 - 18
3/8 - 18
1/2 - 14
1/4 - 18
3/8 - 18
1/2 - 14
3/4 - 14
1/2 - 14
3/4 - 14
5/8
3/4
7/8
5/8
3/4
7/8
5/8
3/4
7/8
5/8
3/4
7/8
1 1/8
7/8
1 1/8
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
10,000
15,000
10,000
Add “-Z6” to part number for part assembled with preset ferrules and nuts.
Dimensions in inches are for reference only, subject to change.
11
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
XHT7
37° Flare to MPI™
Tube Stub
Inches
Parker
Part No.
MPI™ Fittings
37° Flare
Adapter Size
MPI™
Tube Stub
A
1/4
1/4
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/4
3/8
1/4
3/8
1/2
9/16
3/8
1/2
9/16
2.24
2.47
2.37
2.60
2.87
2.93
2.77
3.04
3.10
4-4 XHT7
4-6 XHT7
6-4 XHT7
6-6 XHT7
6-8 XHT7
6-9 XHT7
8-6 XHT7
8-8 XHT7
8-9 XHT7
T
Thread
W
Hex
7/16 - 20 1/2
7/16 - 20 1/2
9/16 - 18 5/8
9/16 - 18 5/8
9/16 - 18 5/8
9/16 - 18 5/8
3/4 - 16 13/16
3/4 - 16 13/16
3/4 - 16 13/16
Working
Pressure
(PSIG)
15,000
15,000
12,500
12,500
12,500
12,500
12,500
12,500
12,500
Add “-Z6” to part number for part assembled with preset ferrules and nuts.
Dimensions in inches are for reference only, subject to change.
X41HT7
High Pressure to MPI™
Tube Stub
Inches
Parker
Part No.
High Pressure
Adapter Size
MPI™
Tube Stub
4-4 X41HT7
4-6 X41HT7
4-8 X41HT7
4-9 X41HT7
6-4 X41HT7
6-6 X41HT7
6-8 X41HT7
6-9 X41HT7
9-4 X41HT7
9-6 X41HT7
9-8 X41HT7
9-9 X41HT7
1/4
1/4
1/4
1/4
3/8
3/8
3/8
3/8
9/16
9/16
9/16
9/16
1/4
3/8
1/2
9/16
1/4
3/8
1/2
9/16
1/4
3/8
1/2
9/16
A
T
Thread
W
Hex
Working
Pressure
(PSIG)
2.59
2.83
3.10
3.16
2.92
3.16
3.43
3.49
3.25
3.49
3.75
3.82
9/16 - 18
9/16 - 18
9/16 - 18
9/16 - 18
3/4 - 16
3/4 - 16
3/4 - 16
3/4 - 16
1 1/8 - 12
1 1/8 - 12
1 1/8 - 12
1 1/8 - 12
5/8
5/8
5/8
5/8
13/16
13/16
13/16
13/16
1-3/16
1-3/16
1-3/16
1-3/16
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
Add “-Z6” to part number for part assembled with preset ferrules and nuts.
Dimensions in inches are for reference only, subject to change.
X47HT7
Medium Pressure Port
Connector to MPI™ Tube Stub
Parker Part No.
9-6 X47HT7
9-9 X47HT7
12-9 X47HT7
12-12 X47HT7
16-9 X47HT7
16-12 X47HT7
16-16 X47HT7
MP Port
Connector
#1
9/16
9/16
3/4
3/4
1
1
1
Inches
MPI
Tube Stub
#2
3/8
9/16
9/16
3/4
9/16
3/4
1
A
K
Working
Pressure
(PSIG)
3.21
3.53
3.72
4.07
4.23
4.57
5.19
1.61
3.03
1.94
3.44
3.44
3.79
4.41
15,000
15,000
15,000
15,000
15,000
15,000
12,500
End # 1 must be used with a Medium Pressure Gland.
Add “-Z6” to part number for part assembled with preset ferrules and nuts.
Dimensions in inches are for reference only, subject to change.
12
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
X42HT7
Medium Pressure to
MPI™ Tube Stub
Inches
Parker
Part No.
Medium Pressure
Adapter Size
MPI™
Tube Stub
1/4
1/4
1/4
1/4
3/8
3/8
3/8
3/8
9/16
9/16
9/16
9/16
9/16
3/4
3/4
1/4
3/8
1/2
9/16
1/4
3/8
1/2
9/16
1/4
3/8
1/2
9/16
3/4
9/16
3/4
4-4 X42HT7
4-6 X42HT7
4-8 X42HT7
4-9 X42HT7
6-4 X42HT7
6-6 X42HT7
6-8 X42HT7
6-9 X42HT7
9-4 X42HT7
9-6 X42HT7
9-8 X42HT7
9-9 X42HT7
9-12 X42HT7
12-9 X42HT7
12-12 X42HT7
T
Thread
A
W
Hex
2.68
7/16 - 20
5/8
2.92
7/16 - 20
5/8
3.18
7/16 - 20
5/8
3.25
7/16 - 20
5/8
2.94
9/16 - 18
3/4
3.17
9/16 - 18
3/4
3.44
9/16 - 18
3/4
3.50
9/16 - 18
3/4
3.25 13/16 - 16
7/8
3.49 13/16 - 16
7/8
3.75 13/16 - 16
7/8
3.81 13/16 - 16
7/8
4.16 13/16 - 16
7/8
4.00 3/4 - 14 NPS 1 1/8
4.35 3/4 - 14 NPS 1 1/8
Working
Pressure
(PSIG)
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
Add “-Z6” to part number for part assembled with preset ferrules and nuts.
Dimensions in inches are for reference only, subject to change.
T7HOA
Inches
MPI™ Tube Stub
to Male SAE O-ring
Parker
Part No.
4-4 T7HOA
4-6 T7HOA
4-8 T7HOA
6-4 T7HOA
6-6 T7HOA
6-8 T7HOA
8-4 T7HOA
8-6 T7HOA
8-8 T7HOA
9-4 T7HOA
9-6 T7HOA
9-8 T7HOA
SAE
MPI™
Tube Stub O-Ring End
1/4
1/4
1/4
3/8
3/8
3/8
1/2
1/2
1/2
9/16
9/16
9/16
1/4
3/8
1/2
1/4
3/8
1/2
1/4
3/8
1/2
1/4
3/8
1/2
A
B
T
Thread
2.25
2.35
2.49
2.48
2.58
2.72
2.75
2.85
2.99
2.81
2.91
3.05
.43
.47
.55
.43
.47
.55
.43
.47
.55
.43
.47
.55
7/16 - 20
9/16 - 18
3/4 - 16
7/16 - 20
9/16 - 18
3/4 - 16
7/16 - 20
9/16 - 18
3/4 - 16
7/16 - 20
9/16 - 18
3/4 - 16
W
Hex
Working
Pressure
(PSIG)
9/16
11/16
7/8
9/16
11/16
7/8
9/16
11/16
7/8
5/8
11/16
7/8
12,500
12,500
12,500
12,500
12,500
12,500
12,500
12,500
12,500
12,500
12,500
12,500
Add “-Z6” to part number for part assembled with preset ferrules and nuts.
* All male o-ring ends for MPI™ fittings are heavy duty and comply with SAE J1926-2. This end
has maximum thread engagement for strength and requires the minimum full thread engagement
specified in SAE J9126 for the female port. Standard O-ring material is Nitrile #N0552-90.
Dimensions in inches are for reference only, subject to change.
M40HT7
Type “M” High Pressure
Hose Adapter to MPI™ Tube
Stub
Inches
Parker
Part No.
Hose*
Adapter Size
MPI™
Tube Stub
6-4 M40HT7
6-6 M40HT7
8-6 M40HT7
8-9 M40HT7
11-6 M40HT7
11-9 M40HT7
11-12 M40HT7
16-12 M40HT7
16-16 M40HT7
-6
-6
-8
-8
-11
-11
-11
-16
-16
1/4
3/8
3/8
9/16
3/8
9/16
3/4
3/4
1
A
2.31
2.55
2.74
3.12
2.99
3.31
3.66
3.91
4.51
T
Thread
W
Hex
Working
Pressure
(PSIG)
9/16 - 18
9/16 - 18
3/4 - 16
3/4 - 16
1 - 12
1 - 12
1 - 12
1 5/16 - 12
1 5/16 - 12
5/8
5/8
13/16
13/16
1 1/16
1 1/16
1 1/16
1 3/8
1 3/8
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
12,500
Add “-Z6” to part number for part assembled with preset ferrules and nuts.
Dimensions in inches are for reference only, subject to change.
13
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Fittings
Catalog 4234
MPI™ Medium Pressure Fittings
Catalog 4234
TRBMP7
Inches
MPI™ Tube Stub Reducer
MPI™ Fittings
Parker
Part No.
MPI™ Tube
Stub #1
MPI™
Size #2
4-6 TRBMP7
4-8 TRBMP7
4-9 TRBMP7
6-4 TRBMP7
6-8 TRBMP7
6-9 TRBMP7
8-4 TRBMP7
8-6 TRBMP7
9-4 TRBMP7
9-6 TRBMP7
9-12 TRBMP7
12-4 TRBMP7
12-6 TRBMP7
12-9 TRBMP7
1/4
1/4
1/4
3/8
3/8
3/8
1/2
1/2
9/16
9/16
9/16
3/4
3/4
3/4
3/8
1/2
9/16
1/4
1/2
9/16
1/4
3/8
1/4
3/8
3/4
1/4
3/8
9/16
A
3.49
3.94
4.00
3.30
4.17
4.24
3.56
3.99
3.63
4.06
4.97
4.17
4.42
4.82
W
Hex
Working
Pressure
(PSIG)
3/4
1
1 1/16
5/8
1
1 1/16
5/8
3/4
5/8
3/4
1 3/8
13/16
13/16
1 1/16
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
Add “-Z6” to part number for part assembled with preset ferrules and nuts.
Dimensions in inches are for reference only, subject to change.
T7HG
MPI™ Tube Stub
to Female NPT Pipe
Inches
Parker
Part No.
4-2 T7HG
4-4 T7HG
4-8 T7HG
6-2 T7HG
6-4 T7HG
6-8 T7HG
8-2 T7HG
8-4 T7HG
8-8 T7HG
9-4 T7HG
9-8 T7HG
12-8 T7HG
12-12 T7HG
16-16 T7HG
MPI™
Tube Stub
Female
NPT End
A
1/4
1/4
1/4
3/8
3/8
3/8
1/2
1/2
1/2
9/16
9/16
3/4
3/4
1
1/8
1/4
1/2
1/8
1/4
1/2
1/8
1/4
1/2
1/4
1/2
1/2
3/4
1
2.09
2.28
2.64
2.33
2.52
2.88
2.60
2.79
3.14
2.84
3.20
3.55
3.60
4.38
B
NPT
Thread
.72
1/8 - 27
.91
1/4 - 18
1.27
1/2 - 14
.72
1/8 - 27
.91
1/4 - 18
1.27
1/2 - 14
.72
1/8 - 27
.91
1/4 - 18
1.27
1/2 - 14
.91
1/4 - 18
1.27
1/2 - 14
1.27
1/2 - 14
1.31 3/4 - 11 1/2
1.50 1 - 11 1/2
W
Hex
Working
Pressure
(PSIG)
13/16
1
1 3/8
13/16
1
1 3/8
13/16
1
1 3/8
1
1 3/8
1 3/8
1 1/2
1 7/8
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
10,000
10,000
Add “-Z6” to part number for part assembled with preset ferrules and nuts.
Dimensions in inches are for reference only, subject to change.
14
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
MP7PC
Inches
MPI™ Port Connector
MPI™ Tube MPI™
1
Stub #1 Port #2
Parker
Part No.
4-4 MP7PC
4-6 MP7PC
6-6 MP7PC
6-8 MP7PC
6-9 MP7PC
8-8 MP7PC
9-9 MP7PC
9-12 MP7PC
12-12 MP7PC
12-16 MP7PC
16-16 MP7PC
K
A
Working
Pressure
(PSIG)
1/4
1/4
2.69
2.23
15,000
1/4
3/8
2.93
2.40
15,000
3/8
3/8
3.17
2.64
15,000
3/8
1/2
3.43
2.68
15,000
3/8
9/16
3.50
2.75
15,000
1/2
1/2
3.70
2.95
15,000
9/16
9/16
3.82
3.07
15,000
9/16 3/4 4.173.3215,000
3/4
3/4
4.52
3.67
15,000
3/4
1
5.12
4.07
12,500
1
1
5.74
4.70
12,500
Assemble 1/4 to 1/2 turn from finger tight.
Add “-Z6” to part number for part assembled with preset ferrules and nuts.
1
Dimensions in inches are for reference only, subject to change.
NBMP7
45° MPI™ Union Elbow
Inches
Parker
Part No.
MPI™
Size
A
4-4 NBMP7
6-6 NBMP7
8-8 NBMP7
9-9 NBMP7
12-12 NBMP7
1/4
3/8
1/2
9/16
3/4
2.56
3.10
3.76
3.82
4.76
C
1.50
1.81
2.18
2.24
2.82
W
Th'k
L
1.38
1.63
2.13
2.13
2.63
5/8
3/4
1
1
1 3/8
Working
Pressure
(PSIG)
15,000
15,000
15,000
15,000
15,000
Dimensions in inches are for reference only, subject to change.
15
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Fittings
Catalog 4234
MPI™ Medium Pressure Fittings
Catalog 4234
T7NBT7
Inches
45° MPI™ Tube Stub Elbow
MPI™ Fittings
Parker
Part No.
Tube
Size
L
R
Working
Pressure
(PSIG)
4 T7NBT7-SS
* 4 T7NBT7-SS 2.9
4 T7NBT7-SS 6.0
4 T7NBT7-SS 8.0
4 T7NBT7-SS 10.0
4 T7NBT7-SS 12.0
6 T7NBT7-SS
* 6 T7NBT7-SS 3.4
6 T7NBT7-SS 6.0
6 T7NBT7-SS 8.0
6 T7NBT7-SS 10.0
6 T7NBT7-SS 12.0
9 T7NBT7-SS
* 9 T7NBT7-SS 4.2
9 T7NBT7-SS 6.0
9 T7NBT7-SS 8.0
9 T7NBT7-SS 10.0
9 T7NBT7-SS 12.0
12 T7NBT7-SS
12 T7NBT7-SS 5.1
12 T7NBT7-SS 6.0
12 T7NBT7-SS 8.0
12 T7NBT7-SS 10.0
12 T7NBT7-SS 12.0
1/4
1/4
1/4
1/4
1/4
1/4
3/8
3/8
3/8
3/8
3/8
3/8
9/16
9/16
9/16
9/16
9/16
9/16
3/4
3/4
3/4
3/4
3/4
3/4
1.69
2.88
6.00
8.00
10.00
12.00
2.14
3.42
6.00
8.00
10.00
12.00
2.77
4.18
6.00
8.00
10.00
12.00
3.55
5.11
6.00
8.00
10.00
12.00
0.75
0.75
0.75
0.75
0.75
0.75
1.25
1.25
1.25
1.25
1.25
1.25
2.00
2.00
2.00
2.00
2.00
2.00
3.00
3.00
3.00
3.00
3.00
3.00
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
Assemble 1/2 turn from finger tight.
* Similar Assembled Lengths as NBMP7 with two (2) MP7PCs.
Dimensions in inches are for reference only, subject to change.
EBMP7
MPI™ Union Elbow
Inches
MPI™
Size
Parker
Part No.
4-4 EBMP7
6-6 EBMP7
8-8 EBMP7
9-9 EBMP7
10-10 EBMP7
12-12 EBMP7
16-16 EBMP7
C
H
L
W
Th'k
1/41.531.881.035/8
3/81.862.251.243/4
1/2
2.22
2.81
1.54
1
9/16
2.29
2.88
1.54
1
5/8
2.46
3.09
1.71
1 3/16
3/4
2.82
3.51
1.94
1 3/8
1
3.63
4.51
2.50
1 3/4
Working
Pressure
(PSIG)
15,000
15,000
15,000
15,000
15,000
15,000
12,500
Dimensions in inches are for reference only, subject to change.
16
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
T7EBT7
Inches
MPI™ Tube Elbow
Parker
Part No.
4 T7EBT7-SS
* 4 T7EBT7-SS 2.9
4 T7EBT7-SS 6.0
4 T7EBT7-SS 8.0
4 T7EBT7-SS 10.0
4 T7EBT7-SS 12.0
6 T7EBT7-SS
* 6 T7EBT7-SS 3.5
6 T7EBT7-SS 6.0
6 T7EBT7-SS 8.0
6 T7EBT7-SS 10.0
6 T7EBT7-SS 12.0
* 9 T7EBT7-SS
9 T7EBT7-SS 6.0
9 T7EBT7-SS 8.0
9 T7EBT7-SS 10.0
9 T7EBT7-SS 12.0
12 T7EBT7-SS
12 T7EBT7-SS 6.0
12 T7EBT7-SS 8.0
12 T7EBT7-SS 10.0
12 T7EBT7-SS 12.0
Tube
Size
H
R
Working
Pressure
(PSIG)
1/4
1/4
1/4
1/4
1/4
1/4
3/8
3/8
3/8
3/8
3/8
3/8
9/16
9/16
9/16
9/16
9/16
3/4
3/4
3/4
3/4
3/4
2.12
2.91
6.00
8.00
10.00
12.00
2.88
3.47
6.00
8.00
10.00
12.00
4.22
6.00
8.00
10.00
12.00
5.31
6.00
8.00
10.00
12.00
0.75
0.75
0.75
0.75
0.75
0.75
1.25
1.25
1.25
1.25
1.25
1.25
2.00
2.00
2.00
2.00
2.00
3.00
3.00
3.00
3.00
3.00
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
MPI™ Fittings
Catalog 4234
Assemble 1/2 turn from finger tight.
* Same Assembled Lengths as EBMP7 with two (2) MP7PCs.
Dimensions in inches are for reference only, subject to change.
CBMP7
MPI™ to Male
NPT Elbow
Inches
Parker
Part No.
4-4 CBMP7
4-6 CBMP7
4-8 CBMP7
6-4 CBMP7
6-6 CBMP7
6-8 CBMP7
MPI™
Size
NPT
Thread
A
B
C
1/4
1/4
1/4
3/8
3/8
3/8
1/4 - 18
3/8 - 18
1/2 - 14
1/4 - 18
3/8 - 18
1/2 - 14
1.13
1.13
1.41
1.23
1.23
1.41
.57
.57
.76
.57
.57
.76
1.53
1.56
1.64
1.86
1.86
1.92
L
1.03
1.06
1.14
1.24
1.24
1.30
W
Hex
Working
Pressure
(PSIG)
3/4
3/4
3/4
7/8
7/8
7/8
15,000
12,000
10,000
12,500
12,000
10,000
Dimensions in inches are for reference only, subject to change.
17
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
JBMP7
MPI™ Union Tee
MPI™ Fittings
Inches
MPI™
Size #1
MPI™
Size #2
MPI™
Size #3
A
C1
C2
H
4-4-4 JBMP7
6-6-6 JBMP7
8-8-8 JBMP7
9-9-9 JBMP7
10-10-10 JBMP7
12-12-12 JBMP7
16-16-16 JBMP7
1/4
3/8
1/2
9/16
5/8
3/4
1
1/4
3/8
1/2
9/16
5/8
3/4
1
1/4
3/8
1/2
9/16
5/8
3/4
1
3.06
3.72
4.45
4.57
5.00
5.64
7.27
1.53
1.86
2.22
2.29
2.50
2.82
3.63
1.53
1.86
2.22
2.29
2.50
2.82
3.63
1.88
2.25
2.81
2.88
3.10
3.51
4.51
4-4-6 JBMP7
6-6-4 JBMP7
6-4-4 JBMP7
6-6-8 JBMP7
6-6-9 JBMP7
8-8-6 JBMP7
8-6-6 JBMP7
9-9-4 JBMP7
9-9-6 JBMP7
9-6-4 JBMP7
9-6-6 JBMP7
12-12-9 JBMP7
16-16-9 JBMP7
16-16-12 JBMP7
1/4
3/8
3/8
3/8
3/8
1/2
1/2
9/16
9/16
9/16
9/16
3/4
1
1
1/4
3/8
1/4
3/8
3/8
1/2
3/8
9/16
9/16
3/8
3/8
3/4
1
1
3/8
1/4
1/4
1/2
9/16
3/8
3/8
1/4
3/8
1/4
3/8
9/16
9/16
3/4
3.47
3.72
3.60
4.32
4.45
4.45
4.38
4.57
4.57
4.45
4.45
5.64
7.27
7.27
1.74
1.86
1.86
2.16
2.16
2.22
2.22
2.29
2.29
2.29
2.29
2.82
3.63
3.63
1.74
1.86
1.74
2.16
2.29
2.22
2.16
2.29
2.29
2.16
2.16
2.82
3.63
3.63
2.25
2.13
2.13
2.81
2.88
2.75
2.75
2.63
2.75
2.63
2.75
3.38
4.13
4.26
Parker Part No.
L
W
Th'k
Working
Pressure
(PSIG)
1.03
1.24
1.54
1.54
1.75
1.94
2.50
5/8
3/4
1
1
1 3/16
1 3/8
1 3/4
15,000
15,000
15,000
15,000
15,000
15,000
12,500
1.24
1.24
1.24
1.54
1.54
1.54
1.54
1.54
1.54
1.54
1.54
1.94
2.50
2.50
3/4
3/4
3/4
1
1
1
1
1
1
1
1
1 3/8
1 3/4
1 3/4
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
15,000
12,500
12,500
Dimensions in inches are for reference only, subject to change.
18
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
X44HBMP7
X44 Male by MPI™ Connector
Inches
Parker
Part No.
X44
Adapter
MPI™
Size
A
9-9 X44HBMP7
9-12 X44HBMP7
12-9 X44HBMP7
12-12 X44HBMP7
9/16
9/16
3/4
3/4
9/16
3/4
9/16
3/4
3.20
3.98
3.15
3.89
D
W
Hex
Working
Pressure
(PSIG)
1.54
2.19
1.35
1.96
1-1/16
1-3/8
1-1/4
1-3/8
15,000
15,000
15,000
15,000
Dimensions in inches are for reference only, subject to change.
X44HT7
X44 Male by MPI™ Tube Stub
Inches
Parker
Part No.
X44
Adapter
MPI™
Tube
9/16
9/16
3/4
3/4
9/16
3/4
9/16
3/4
9-9 X44HT7
9-12 X44HT7
12-9 X44HT7
12-12 X44HT7
A
W
Hex
Working
Pressure
(PSIG)
3.60
3.95
3.74
4.09
1
1
1-1/4
1-1/4
15,000
15,000
15,000
15,000
Dimensions in inches are for reference only, subject to change.
M40HX44
Type “M” Male by X44 Male
Parker
Part No.
Type “M”
Adapter
X44
Adapter
6-9 M40HX44
6-12 M40HX44
8-9 M40HX44
8-12 M40HX44
11-9 M40HX44
11-12 M40HX44
3/8
3/8
1/2
1/2
11/16
11/16
9/16
3/4
9/16
3/4
9/16
3/4
Inches
T1
Thread
9/16-18 UNF
9/16-18 UNF
3/4-16 UNF
3/4-16 UNF
1-12 UNF
1-12 UNF
A
W
Hex
Working
Pressure
(PSIG)
1.79
2.06
1.99
2.18
2.04
2.18
1
1-1/4
1
1-1/4
1-1/16
1-1/4
15,000
15,000
15,000
15,000
15,000
15,000
Dimensions in inches are for reference only, subject to change.
X44 Adapter Assembly
Size
T
Thread
B
D
Insertion Depth
ØE
Assembly
Torque
9
12
7/8-14
1-1/8-12
0.91
1.05
0.84
0.98
0.38
0.50
80 ft-lb
165 ft-lb
Dimensions in inches are for reference only, subject to change.
19
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Fittings
MPI™ Medium Pressure Fittings
Catalog 4234
MPI™ Medium Pressure Fittings
Catalog 4234
RBMP7
MPI™ to Male Run
NPT Tee
MPI™ Fittings
Inches
Parker
Part No.
4-4-4 RBMP7
4-4-6 RBMP7
4-6-4 RBMP7
4-6-6 RBMP7
6-4-4 RBMP7
6-4-6 RBMP7
6-6-4 RBMP7
6-6-6 RBMP7
MPI™
Size #1
NPT
Thread #2
MPI™
Size #3
1/4
1/4
1/4
1/4
3/8
3/8
3/8
3/8
1/4 - 18
1/4 - 18
3/8 -18
3/8 -18
1/4 - 18
1/4 - 18
3/8 -18
3/8 -18
1/4
3/8
1/4
3/8
1/4
3/8
1/4
3/8
C1
C2
C3
B
1.63
1.63
1.63
1.63
1.86
1.86
1.86
1.86
1.13
1.23
1.13
1.23
1.23
1.23
1.23
1.23
1.63
1.86
1.63
1.86
1.63
1.86
1.63
1.86
.57
.57
.57
.57
.57
.57
.57
.57
3/4
7/8
3/4
7/8
7/8
7/8
7/8
7/8
15,000
12,500
12,000
12,000
12,500
12,500
12,000
12,000
Working
Pressure
(PSIG)
15,000
12,000
12,500
12,000
A
2.76
2.85
2.76
2.85
3.09
3.09
3.09
3.09
Working
Pressure
(PSIG)
W
Hex
Dimensions in inches are for reference only, subject to change.
SBMP7
MPI™ to Male Branch
NPT Tee
1
2
3
Inches
Parker
Part No.
4-4-4 SBMP7
4-4-6 SBMP7
6-6-4 SBMP7
6-6-6 SBMP7
MPI™
Size #1
1/4
1/4
3/8
3/8
MPI™
NPT
Size #2 Thread #3
1/4 - 18
3/8 -18
1/4 - 18
3/8 -18
1/4
3/8
3/8
3/8
A
3.25
3.25
3.72
3.72
C1
C2
C3
B
W
Hex
1.63
1.63
1.86
1.86
1.63
1.63
1.86
1.86
1.13
1.13
1.23
1.23
.57
.57
.57
.57
3/4
3/4
7/8
7/8
Dimensions in inches are for reference only, subject to change.
20
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
OBMP7
MPI™ Fittings
MPI™ to NPT
Female Branch Tee
Inches
Parker
Part No.
MPI™
Size #1
MPI™
Size #2
NPT
Thread #3
A
C2
C1
C3
B
Working
Pressure
(PSIG)
W
Th'k
4-4-4 OBMP71/4 1/41/4-183.471.741.741.241.24 3/4
6-6-4 OBMP73/8 3/81/4-183.721.861.861.241.24 3/4
6-6-8 OBMP7
3/8
3/8
1/2-14
3.88
1.94
1.94
1.54
1.31
1 3/8
8-8-8 OBMP7
1/2
1/2
1/2-14
4.45
2.22
2.22
1.94
1.54
1 3/8
9-9-8 OBMP7
9/16
9/16
1/2-14
4.57
2.29
2.29
1.94
1.54
1 3/8
12-12-8 OBMP7
3/4
3/4
1/2-14
5.64
2.82
2.82
1.94
1.94
1 3/8
15,000
15,000
15,000
15,000
15,000
15,000
Dimensions in inches are for reference only, subject to change.
KBMP7
MPI™ Union Cross
Inches
MPI™
Size
Parker
Part No.
A
C
L
W
Th'k
4 KBMP7 1/43.061.531.035/8
6 KBMP7 3/83.721.861.243/4
8 KBMP7
1/2
4.45
2.22
1.54
1
9 KBMP7
9/16
4.57
2.29
1.54
1
10 KBMP7
5/8
5.00
2.50
1.75
1 3/16
12 KBMP7
3/4
5.64
2.82
1.94
1 3/8
Working
Pressure
(PSIG)
15,000
15,000
15,000
15,000
15,000
15,000
Dimensions in inches are for reference only, subject to change.
21
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Fittings
Catalog 4234
FNMP7
FNM7
MPI™ Plug,
Assembly
MPI™ Plug, Solid
MPI™ Fittings
Inches
Parker
Part No.
MPI™
Size
4 FNMP7
6 FNMP7
8 FNMP7
9 FNMP7
12 FNMP7
16 FNMP7
1/4
3/8
1/2
9/16
3/4
1
A
W
Hex
Working
Pressure
(PSIG)
1.41
1.65
1.94
2.00
2.35
2.96
9/16
11/16
15/16
1
1 1/4
1 1/2
15,000
15,000
15,000
15,000
15,000
12,500
Inches
Parker
Part No.
MPI™
Size
4 FNM7
6 FNM7
8 FNM7
9 FNM7
12 FNM7
1/4
3/8
1/2
9/16
3/4
A
W
Hex
Working
Pressure
(PSIG)
1.26
1.49
1.76
1.82
2.17
9/16
11/16
15/16
1
1 1/4
15,000
15,000
15,000
15,000
15,000
Assemble 1/4 to 1/2 turn from finger tight.
Assemble 1/4 to 1/2 turn from finger tight and lubricate threads and
taper before each remake.
Dimensions in inches are for reference only, subject to change.
Dimensions in inches are for reference only, subject to change.
PNBMP7
MPFF
MPI™ Cap
MPI™ Front
Ferrule
Inches
Parker
Part No.
MPI™
Size
A
D
W
Hex
Working
Pressure
(PSIG)
4 PNBMP7
6 PNBMP7
8 PNBMP7
9 PNBMP7
10 PNMBP7
12 PNBMP7
16 PNBMP7
1/4
3/8
1/2
9/16
5/8
3/4
1
1.69
2.12
2.62
2.75
2.86
3.53
4.44
1.19
1.49
1.93
2.00
2.11
2.64
3.31
5/8
3/4
1
1 1/16
1 3/16
1 3/8
1 3/4
15,000
15,000
15,000
15,000
15,000
15,000
12,500
Dimensions in inches are for reference only, subject to change.
22
Parker
Part No.
Tube
O.D.
Ferrule
O.D.
4 MPFF
6 MPFF
8 MPFF
9 MPFF
10 MPFF
12 MPFF
16 MPFF
1/4
3/8
1/2
9/16
5/8
3/4
1
0.40
0.52
0.72
0.78
0.84
0.99
1.30
Dimensions in inches are for reference only, subject
to change.
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
BMP7
MPBF
MPI™ Nut
MPI™ Back
Ferrule
Parker
Part No.
MPI™
Size
A
W
Hex
4 BMP7
6 BMP7
8 BMP7
9 BMP7
10 BMP7
12 BMP7
16 BMP7
1/4
3/8
1/2
9/16
5/8
3/4
1
0.81
0.92
0.97
1.03
1.13
1.34
1.74
9/16
11/16
15/16
1
1 1/16
1 1/4
1 1/2
Parker
Part No.
Tube
O.D.
Ferrule
O.D.
4 MPBF
6 MPBF
8 MPBF
9 MPBF
10 MPBF
12 MPBF
16 MPBF
1/4
3/8
1/2
9/16
5/8
3/4
1
0.40
0.52
0.72
0.78
0.84
0.99
1.30
Dimensions in inches are for reference only, subject
to change.
Dimensions in inches are for reference only, subject to change.
Gaugeability Tools
Gap Gauge
This one handy gauge works for all MPI™ sizes. The
end of the gauge checks the fitting gap after make-up.
See page 42 for make-up and inspection instructions.
Parker Part Number: MPI GAP GAUGE
Gap Gauge
23
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Fittings
MPI™ Medium Pressure Fittings
Catalog 4234
MPI™ Medium Pressure Valves
Catalog 4234
Medium Pressure Valves
MPN Series Valves
Parker MPN series valves are designed for multi-turn control of media regulation and shutoff up to 20,000 psi.
Additional packing materials are available for application temperatures from -300°F to +800°F. Standard critical
service design features, such as the packing below the thread and the non-rotating lower stem ensure longer
valve life in rugged applications.
Medium Pressure Valve Connection Types
F
Medium Pressure
Valves
Female NPT
To 15,000 PSI
MP7
MF
Parker MPI™
(Medium Pressure
Inverted)
To 15,000 PSI
Cone & Thread
(Medium Pressure
Female)
To 20,000 PSI
Materials of Construction
Item #
Description
1
Soc Set Screw
2
Handle
3
Upper Stem Assembly
4
Packing Gland
5
Locking Device
6
10-32 X 1/4 Fill HD SCR.
7
Stem Pin
8
Top Packing Washer
9
Packing
10
Bottom Packing Washer
11
Lower Stem
12
Body
Material
Steel
Aluminum
17-4PH
316SS
300 SER. SS
300 SER. SS
304SS
416SS
PTFE
316SS
17-4PH-H900
316SS
24
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Valves
Catalog 4234
Two Way Inline Valves
Valve
Size
4 & 6
8 & 9
12
16
A
1.25
1.375
1.75
2.50
B
.219
.219
.219
.219
Tubing Inches
Size
Parker Part No.
PSI
Connection
Orifice
A
B
C
D
E
1/4" O.D.4MP7-MPNLB-T-SS15,000
3/8" O.D.6MP7-MPNLB-T-SS15,000
1/2" O.D.8MP7-MPNLB-T-SS15,000
9/16" O.D.9MP7-MPNLB-T-SS15,000
3/4" O.D.12MP7-MPNLB-T-SS15,000
3/4" O.D.
12MP7-MPNLBH-T-SS
10,000
1" O.D. 16MP7-MPNLB-T-SS12,500
1/4" MPI
3/8" MPI
1/2" MPI
9/16" MPI
3/4" MPI
3/4" MPI
1" MPI
0.125
0.203
0.313
0.313
0.438
0.516
0.563
4.50
4.50
6.26
6.26
7.00
7.00
8.42
2F-MPNLB-T-SS
4F-MPNLB-T-SS
6F-MPNLB-T-SS
8F-MPNLB-T-SS
12F-MPNLB-T-SS
16F-MPNLB-T-SS
15,000
15,000
15,000
15,000
10,000
10,000
1/8"
1/4"
3/8"
1/2"
3/4"
1"
0.203
0.203
0.312
0.312
0.687
0.687
4.38
4.38
6.13
6.38
8.50
8.50
F
D
.75
1.00
1.19
1.63
G
H
Th'k
2.500.50 0.942.13 0.381.250.221.00
2.500.50 0.942.13 0.381.250.221.00
3.000.63 1.253.00 0.501.380.341.38
3.000.63 1.253.00 0.501.380.341.38
4.130.75 1.503.75 0.631.750.441.75
4.130.75 1.503.75 0.631.750.441.75
4.130.88 1.814.63 1.132.500.561.75
Connection
Inches
Pipe Size Parker Part No.
PSI Female NPT Orifice
A
B
C
D
E
1/8" NPT
1/4" NPT
3/8" NPT
1/2" NPT
3/4" NPT
1" NPT
Screw
Size
10 - 32
10 - 32
10 - 32
10 - 32
F
G
H
Th'k
2.000.38 0.812.00 0.381.250.220.75
2.000.38 0.812.00 0.381.250.220.75
2.500.50 1.132.88 0.501.380.341.00
2.630.75 1.383.13 0.501.380.341.50
4.130.88 1.814.63 1.132.500.561.75
4.130.88 1.814.63 1.132.500.561.75
Dimensions in inches are for reference only, subject to change.
25
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Medium Pressure
Valves
Panel Hole Sizes
Medium Pressure Needle Valve Panel Mount
MPI™ Medium Pressure Valves
Catalog 4234
Two Way Angle Valves
Panel Hole Sizes
Medium Pressure Needle Valve Panel Mount
Valve
Size
4 & 6
Medium Pressure
Valves
8 & 9
12
16
A
1.25
1.375
1.75
2.50
Inches
Tubing
Parker Part No.
PSI
Connection
Orifice
A
B
C
D
1/4" O.D.
3/8" O.D.
1/2" O.D.
9/16" O.D.
3/4" O.D.
3/4" O.D.
1" O.D.
1" O.D.
4MP7-MPNAB-T-SS
6MP7-MPNAB-T-SS
8MP7-MPNAB-T-SS
9MP7-MPNAB-T-SS
12MP7-MPNAB-T-SS
12MP7-MPNABH-T-SS
16MP7-MPNAB-T-SS
16MP7-MPNABH-T-SS
15,000
15,000
15,000
15,000
15,000
10,000
12,500
10,000
1/4" MPI
3/8" MPI
1/2" MPI
9/16 MPI
3/4" MPI
3/4" MPI
1" MPI
1" MPI
0.125
0.203
0.313
0.313
0.438
0.516
0.563
0.688
5.02
5.02
6.84
6.84
7.50
7.50
9.38
9.38
2.50-1.38
2.50-1.38
3.00-1.83
3.00-1.83
3.00
-
2.00
3.00
-
2.00
4.13
-
2.56
4.13
-
2.56
ConnectionInches
Pipe Size Parker Part No.
PSI Female NPT Orifice
A
B
C
D
1/8" NPT
1/4" NPT
3/8" NPT
1/2" NPT
3/4" NPT
1" NPT
2F-MPNAB-T-SS
4F-MPNAB-T-SS
6F-MPNAB-T-SS
8F-MPNAB-T-SS
12F-MPNAB-T-SS
16F-MPNAB-T-SS
15,000
15,000
15,000
15,000
10,000
10,000
1/8"
1/4"
3/8"
1/2"
3/4"
1"
0.203
0.203
0.312
0.312
0.687
0.687
4.81
4.81
6.50
6.50
9.00
9.00
2.00
2.00
2.50
2.63
4.13
4.13
-
-
-
-
-
-
Screw
Size
10 - 32
10 - 32
10 - 32
10 - 32
B
.219
.219
.219
.219
E
2.57
2.57
3.58
3.58
4.25
4.25
5.44
5.44
E
F
0.38
0.38
0.50
0.50
0.63
0.63
1.13
1.13
F
D
.75
1.00
1.19
1.63
G
H
Th'k
1.25 0.221.00
1.25 0.221.00
1.38 0.341.38
1.38 0.341.38
1.75 0.44 1.38
1.75 0.44 1.38
2.50 0.56 1.75
2.50 0.56 1.75
G
H
Th'k
1.252.44 0.381.250.220.75
1.252.44 0.381.250.220.75
1.503.25 0.501.380.341.00
1.503.25 0.501.380.341.50
2.315.13 1.132.500.561.75
2.315.13 1.132.500.561.75
Dimensions in inches are for reference only, subject to change.
26
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Valves
Catalog 4234
Three Way/Two Pressure Connections
Valve
Size
4 & 6
8 & 9
12
16
A
1.25
1.375
1.75
2.50
Inches
Tubing
Parker Part No.
PSI
Connection
Orifice
A
B
C
D
1/4" O.D. 4MP7-MPNXBI-T-SS 15,000
3/8" O.D. 6MP7-MPNXBI-T-SS 15,000
1/2" O.D. 8MP7-MPNXBI-T-SS 15,000
9/16" O.D. 9MP7-MPNXBI-T-SS 15,000
3/4" O.D.12MP7-MPNXBI-T-SS15,000
3/4" O.D.
12MP7-MPNXBIH-T-SS10,000
1" O.D.16MP7-MPNXBI-T-SS12,500
1" O.D.16MP7-MPNXBIH-T-SS10,000
1/4" MPI
3/8" MPI
1/2" MPI
9/16" MPI
3/4" MPI
3/4" MPI
1" MPI
1" MPI
0.125
0.203
0.313
0.313
0.438
0.516
0.563
0.688
5.21
5.21
7.09
7.09
7.88
7.88
9.75
9.75
B
.219
.219
.219
.219
E
Screw
Size
10 - 32
10 - 32
10 - 32
10 - 32
F
D
.75
1.00
1.19
1.63
G
H
Th'k
2.501.21 1.65 2.84 0.38 1.25 0.221.00
2.501.21 1.65 2.84 0.38 1.25 0.221.00
3.001.50 2.12 3.88 0.50 1.38 0.341.38
3.001.50 2.12 3.88 0.50 1.38 0.341.38
3.002.63 2.384.63 0.631.750.441.38
3.002.63 2.384.63 0.631.750.441.38
4.132.13 3.065.88 1.132.500.561.75
4.132.13 3.065.88 1.132.500.561.75
Dimensions in inches are for reference only, subject to change.
Three Way/One Pressure Connection
Panel Hole Sizes
Medium Pressure Needle Valve Panel Mount
Valve
Size
4 & 6
8 & 9
12
16
A
1.25
1.375
1.75
2.50
Inches
Tubing
Parker Part No.
PSI
Connection
Orifice
A
B
C
D
1/4" O.D. 4MP7-MPNXBO-T-SS 15,000
3/8" O.D. 6MP7-MPNXBO-T-SS 15,000
1/2" O.D. 8MP7-MPNXBO-T-SS 15,000
9/16" O.D. 9MP7-MPNXBO-T-SS 15,000
3/4" O.D.
12MP7-MPNXBO-T-SS15,000
3/4" O.D.
12MP7-MPNXBOH-T-SS
10,000
1" O.D.16MP7-MPNXBO-T-SS12,500
1" O.D.16MP7-MPNXBOH-T-SS
10,000
1/4" MPI
3/8" MPI
1/2" MPI
9/16" MPI
3/4" MPI
3/4" MPI
1" MPI
1" MPI
0.125
0.203
0.313
0.313
0.438
0.516
0.563
0.688
5.02
5.02
6.84
6.84
7.50
7.50
9.38
9.38
B
.219
.219
.219
.219
E
Screw
Size
10 - 32
10 - 32
10 - 32
10 - 32
F
D
.75
1.00
1.19
1.63
G
H
Th'k
2.501.38 1.38 2.57 0.38 1.25 0.221.00
2.501.38 1.38 2.57 0.38 1.25 0.221.00
3.001.88 1.88 3.63 0.50 1.38 0.341.38
3.001.88 1.88 3.63 0.50 1.38 0.341.38
3.002.00 2.004.25 0.631.750.441.38
3.002.00 2.004.25 0.631.750.441.38
4.132.63 2.635.44 1.132.500.561.75
4.132.63 2.635.44 1.132.500.561.75
Dimensions in inches are for reference only, subject to change.
27
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Medium Pressure
Valves
Panel Hole Sizes
Medium Pressure Needle Valve Panel Mount
MPI™ Medium Pressure Valves
Catalog 4234
Three Way/Two Stem Connection
Panel Hole Sizes
Medium Pressure Needle Valve Panel Mount
Valve
Size
4 & 6
Medium Pressure
Valves
8 & 9
12
16
B
.219
.219
.219
.219
A
1.25
1.375
1.75
2.50
Inches
Tubing
Parker Part No.
PSI
Connection
Orifice
A
B
C
D
1/4" O.D.4MP7-MPNXBD-T-SS15,000
3/8" O.D.6MP7-MPNXBD-T-SS15,000
1/2" O.D.8MP7-MPNXBD-T-SS15,000
9/16" O.D.9MP7-MPNXBD-T-SS15,000
3/4" O.D.12MP7-MPNXBD-T-SS
15,000
3/4" O.D.
12MP7-MPNXBDH-T-SS
10,000
1" O.D. 16MP7-MPNXBD-T-SS
12,500
1" O.D.16MP7-MPNXBDH-T-SS
10,000
1/4" MPI
3/8" MPI
1/2" MPI
9/16" MPI
3/4" MPI
3/4" MPI
1" MPI
1" MPI
0.125
0.203
0.313
0.313
0.438
0.516
0.563
0.688
5.75
5.75
8.38
8.38
9.75
9.75
12.19
12.19
E
Screw
Size
10 - 32
10 - 32
10 - 32
10 - 32
F
D
.75
1.00
1.19
1.63
G
H
Th'k
2.501.70 1.193.38 0.381.250.221.00
2.501.70 1.193.38 0.381.250.221.00
3.002.56 1.755.13 0.501.380.341.38
3.002.56 1.755.13 0.501.380.341.38
3.003.25 2.256.50 0.631.750.441.38
3.003.25 2.256.50 0.631.750.441.38
4.134.13 2.818.25 1.132.500.561.75
4.134.13 2.818.25 1.132.500.561.75
Dimensions in inches are for reference only, subject to change.
Two Way Angle Valves (Replaceable Seat)
Panel Hole Sizes
Medium Pressure Needle Valve Panel Mount
Valve
Size
4 & 6
8 & 9
12
16
B
.219
.219
.219
.219
A
1.25
1.375
1.75
2.50
Inches
Tubing
Parker Part No.
PSI
Connection
Orifice
A
B
C
D
1/4" O.D. 4MP7-MPNABR-T-SS 15,000
3/8" O.D. 6MP7-MPNABR-T-SS 15,000
1/2" O.D. 8MP7-MPNABR-T-SS 15,000
9/16" O.D. 9MP7-MPNABR-T-SS 15,000
3/4" O.D. 12MP7-MPNABR-T-SS 15,000
3/4" O.D. 12MP7-MPNABRH-T-SS 10,000
1" O.D. 16MP7-MPNABR-T-SS 12,500
1" O.D. 16MP7-MPNABRH-T-SS 10,000
1/4" MPI
3/8" MPI
1/2" MPI
9/16" MPI
3/4" MPI
3/4" MPI
1" MPI
1" MPI
0.125
0.203
0.313
0.313
0.438
0.516
0.563
0.688
5.87
5.87
8.25
8.25
8.88
8.88
11.13
11.13
2.50
2.50
3.00
3.00
3.00
3.00
4.13
4.13
-
-
-
-
-
-
-
-
1.38
1.38
2.00
2.00
2.00
2.00
2.56
2.56
Screw
Size
10 - 32
10 - 32
10 - 32
10 - 32
D
.75
1.00
1.19
1.63
E
F
G
H
Th'k
2.57
2.57
3.63
3.63
4.25
4.25
5.44
5.44
0.38
0.38
0.50
0.50
0.63
0.63
1.13
1.13
1.25
1.25
1.38
1.38
1.75
1.75
2.50
2.50
0.22
0.22
0.34
0.34
0.44
0.44
0.56
0.56
1.00
1.00
1.38
1.38
1.38
1.38
1.75
1.75
Dimensions in inches are for reference only, subject to change.
28
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Valves
Catalog 4234
How to Order MPN Series Valves
The correct part number is easily derived from the following example and ordering chart. The nine product
characteristics required are coded as shown in the chart.
The following example describes an MPN Series needle valve with 1/4" MPI connections, 2 way angle flow path,
blunt stem, PTFE packing, stainless steel body and the option for over critical service.
Example: 4MP7-MPNAB-T-SS-OC
MP7
–
Inlet/Outlet
Connection
Connection
Type
Size
Inlet /
Outlet
Connection
Size
2* 1/8"
4
1/4"
6
3/8"
1/2"
8
9** 9/16"
12
3/4"
1"
16
Connection
Type
FFemale
Pipe
MP7Parker
MPI™
MFFemale
Cone &
Thread
WTube
Socket
Weld
* Female Pipe
PSWPipe
Only
Socket
**MP7 and MF
Weld
only
MPN
A
B
Valve
Series
Valve
Type
Stem
Type
Valve
Series
MPN
–
High
Flow
Stem
Type
BBlunt
RRegulating
Valve
Type
L
2-Way Inline
A
2-Way Angle
X***I 3-Way 2-Pressure
Connections
X***D 3-Way 2-Stem
Connection
A***R 2-Way Angle Valve
(Replaceable
Seat)
T
–
–
SS
Packing
Material
Body
Material
Packing
Material
TPTFE
GGraphoil®
Body
Material
SSStainless
Steel
High
Flow
Blank Standard Flow
H
High Flow
OC
Options
Options
(See Below)
OC Over Critical
HYDHydrogen
Compatible
LTLow
Temperature
*** Needle Type Inserted Here
How to Order Options
Over Critical – add the suffix -OC to the end of the part number to specify over critical service.
Hydrogen Service – add the suffix -HYD to the end of the part number for a valve suitable for hydrogen service.
Low Temperature – add the suffix -LT to the end of the part number for low temperature service.
Grafoil® is a registered trademark of GrafTech International Holdings, Inc.
29
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Medium Pressure
Valves
4
MPI™ Medium Pressure Valves
Catalog 4234
Over Critical Valves
Medium Pressure
Valves
Size
Parker Part No.
PSI
Connection
Orifice
A
B
C
D
E
F
G
H
Th'k
1/4" O.D.
3/8" O.D.
1/2" O.D.
9/16" O.D.
3/4" O.D.
1" O.D.
1/8" NPT
1/4" NPT
3/8" NPT
1/2" NPT
3/4" NPT
1" NPT
4MP7-MPNLB-G-SS-OC
6MP7-MPNLB-G-SS-OC
8MP7-MPNLB-G-SS-OC
9MP7-MPNLB-G-SS-OC
12MP7-MPNLB-G-SS-OC
16MP7-MPNLB-G-SS-OC
2F-MPNLB-G-SS-OC
4F-MPNLB-G-SS-OC
6F-MPNLB-G-SS-OC
8F-MPNLB-G-SS-OC
12F-MPNLB-G-SS-OC
16F-MPNLB-G-SS-OC
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
4MP7
6MP7
8MP7
9MP7
12MP7
16MP7
1/8" NPTF
1/4" NPTF
3/8" NPTF
1/2" NPTF
3/4" NPTF
1" NPTF
0.125
0.203
0.313
0.313
0.438
0.563
0.203
0.203
0.312
0.312
0.687
0.687
4.50
4.50
6.26
6.26
7.00
8.42
4.38
4.38
6.13
6.38
8.50
8.50
2.50
2.50
3.00
3.00
3.00
4.13
2.00
2.00
2.5
2.63
4.13
4.13
0.50
0.50
0.63
0.63
0.75
0.88
0.38
0.38
0.50
0.75
0.88
0.88
0.94
0.94
1.25
1.25
1.50
1.81
0.81
0.81
1.13
1.38
1.81
1.81
2.13
2.13
3.00
3.00
3.75
4.63
2.00
2.00
2.88
3.13
4.63
4.63
0.38
0.38
0.50
0.50
0.63
1.13
0.38
0.38
0.50
0.50
1.13
1.13
1.25
1.25
1.38
1.38
1.75
2.5
1.25
1.25
1.38
1.38
2.5
2.5
0.22
0.22
0.34
0.34
0.44
0.56
0.22
0.22
0.34
0.34
0.56
0.56
0.75
0.75
1.00
1.00
1.38
1.75
0.75
0.75
1.00
1.50
1.75
1.75
Dimensions in inches are for reference only, subject to change.
Pressure vs. Temperature Chart
Materials of Construction
Grafoil® is a registered trademark of GrafTech International Holdings, Inc.
30
Item #
Description
Material
1
2
3
4
5
6
7
8
9
10
11
12
Set Screw
Handle
Upper Stem Assembly
Packing Gland
Locking Device
Lock Screw
Stem Pin
Top Packing Washer
Packing
Bottom Pack Washer
Lower Stem
Body
316SS
303SS
416SS
316SS
304SS
304SS
304SS
416SS
Grafoil®
316SS
316SS
316SS
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Valves
Catalog 4234
Bleed Valve
2
Materials of Construction
1
Item #
Qty
Description
Material
1
2
3
4
1
1
1
2
Soc Set Screw
Handle
Stem
Rolling Pin
5
1
O-Ring
6
1
Body
300 Ser. SS
Aluminum
17-4PH-H900
420SS
Fluorocarbon
Rubber*
316SS
3
4
6
5
Parker
Part No.
PSI
Connection
9T7-MPBV-V-SS 15,000
9/16" Tube Stub
9HM-MPBV-V-SS 30,000 9/16" High Pressure Male
Example: 9T7-MPBV-KZ-SS
Gauge Valve
Materials of Construction
2
1
3
4
6
5
10
8
7
9
Parker
Part No.
PSI
Connection
9MP7-MPGV-V-SS 15,000
9/16" MPI™
9HF-MPGV-V-SS 30,000 9/16" High Pressure Female
31
Item #
Qty
Description
Material
1
2
3
4
5
6
7
8
9
10
1
1
1
1
1
1
1
1
1
1
Soc Set Screw
Handle
Stem Assembly
Packing Gland
Locking Device
10-32 x 1/4 Fill Hd Scr.
Top Packing Washer
Packing
Bottom Packing Washer
Body
Steel
Aluminum
17-4PH
316SS
300 Ser. SS
300 Ser. SS
416SS
Fluorocarbon Rubber
316SS
316SS
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Medium Pressure
Valves
*Optional Seal Materials
KZ Highly Fluorinated Fluorocarbon Rubber
BN Nitrile Rubber
EPR Ethylene Propylene Rubber
MPI™ Medium Pressure Valves
Catalog 4234
MPB Series Valves
Parker MPB series manually, pneumatically and electrically actuated two-way and three-way ball valves are
designed for 1/4 and 1/2 turn media shutoff or switching applications up to 20,000 psi. Our trunion style ball
design and spring loaded seats make the MPB series ideal for severe service applications. The end connector
design enables a variety of end connections and combinations for specific customer applications.
.187 Orifice
(Standard)
Two Way
Ball Valves
Medium Pressure
Valves
Parker
Part No.
Tubing
Standard
1/8" O.D.
1/4" O.D.
1/4" O.D.
3/8" O.D.
3/8" O.D.
1/2" O.D.
9/16" O.D.
2F-MPBLPK-V-SSP
4F-MPBLPK-V-SSP
4MP7-MPBLPK-V-SSP
6F-MPBLPK-V-SSP
6MP7-MPBLPK-V-SSP
8MP7-MPBLPK-V-SSP
9MP7-MPBLPK-V-SSP
.375 Orifice
(High Flow)
Inches
Minimum Orifice
Cv
A
PSI
Connection
Orifice
15,000
15,000
15,000
15,000
15,000
15,000
15,000
1/8" NPT
1/4" NPT
1/4" MPI
3/8" NPT
3/8" MPI
1/2" MPI
9/16" MPI
0.187
0.187
0.187
0.187
0.187
0.187
0.187
0.187
0.187
0.125
0.187
0.187
0.187
0.187
1.45
1.45
0.45
1.45
1.45
1.45
1.45
4.63
4.63
5.00
4.65
5.00
5.50
5.50
15,000
15,000
15,000
15,000
12,500
1/2" NPT
1/2" MPI
9/16" MPI
3/4" MPI
1" MPI
0.375
0.375
0.375
0.375
0.375
0.375
0.359
0.359
0.375
0.375
6.08
5.82
5.82
6.08
6.08
5.63
6.44
6.44
6.67
8.00
10,000
10,000
3/4" MPI
1" MPI
0.500
0.500
0.469
0.500
7.60
8.80
6.86
8.48
High Flow (H)
1/2" O.D.
1/2" O.D.
9/16" O.D.
3/4" O.D.
1" O.D.
8F-MPBLPKH-V-SSP
8MP7-MPBLPKH-V-SSP
9MP7-MPBLPKH-V-SSP
12MP7-MPBLPKH-V-SSP
16MP7-MPBLPKH-V-SSP
Ultra High Flow (UH)
3/4" O.D.
1" O.D.
12MP7-MPBLPKUH-V-SSP
16MP7-MPBLPKUH-V-SSP
Dimensions in inches are for reference only, subject to change.
.500 Orifice
Two-Way
(UltraHigh Flow)
32
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Valves
Catalog 4234
Diverter
3-Way 90°
Tubing
Standard
1/8" O.D.
1/4" O.D.
1/4" O.D.
3/8" O.D.
3/8" O.D.
1/2" O.D.
9/16" O.D.
.187 Orifice
(Standard)
2F-MPBXPKD-V-SSP
4F-MPBXPKD-V-SSP
4MP7-MPBXPKD-V-SSP
6F-MPBXPKD-V-SSP
6MP7-MPBXPKD-V-SSP
8MP7-MPBXPKD-V-SSP
9MP7-MPBXPKD-V-SSP
.375 Orifice
(High Flow)
Selector
3-Way 180°
Inches
Minimum
Orifice
Cv
PSI
Connection
Orifice
2F-MPBXPK-V-SSP
4F-MPBXPK-V-SSP
4MP7-MPBXPK-V-SSP
6F-MPBXPK-V-SSP
6MP7-MPBXPK-V-SSP
8MP7-MPBXPK-V-SSP
9MP7-MPBXPK-V-SSP
15,000
15,000
15,000
15,000
15,000
15,000
15,000
1/8" NPT
1/4" NPT
1/4" MPI
3/8" NPT
3/8" MPI
182" MPI
9/16" MPI
0.187
0.187
0.187
0.187
0.187
0.187
0.187
0.187
0.187
0.125
0.187
0.187
0.187
0.187
8F-MPBXPKH-V-SSP
8MP7-MPBXPKH-V-SSP
9MP7-MPBXPKH-V-SSP
12MP7-MPBXPKH-V-SSP
16MP7-MPBXPKH-V-SSP
15,000
15,000
15,000
15,000
15,000
1/2" NPT
1/2" MPI
9/16" MPI
3/4" MPI
1" MPI
0.375
0.375
0.375
0.375
0.375
10,000
10,000
3/4" MPI
1" MPI
0.500
0.500
A
B
0.71
0.71
0.18
0.71
0.71
0.71
0.71
4.63
4.63
5.00
4.65
5.00
5.50
5.50
0.50
1.06
1.18
1.06
1.18
1.44
1.44
0.375
0.359
0.359
0.375
0.375
2.40
2.30
2.30
2.40
2.40
5.63
6.44
6.44
6.67
7.45
1.06
1.37
1.37
1.18
1.99
0.469
0.500
3.20
3.80
6.86
8.48
1.37
2.18
High Flow (H)
1/2" O.D.
1/2" O.D.
9/16" O.D.
3/4" O.D.
1" O.D.
8F-MPBXPKDH-V-SSP
8MP7-MPBXPKDH-V-SSP
9MP7-MPBXPKDH-V-SSP
12MP7-MPBXPKDH-V-SSP
16MP7-MPBXPKDH-V-SSP
Ultra High Flow (UH)
3/4" O.D.
1" O.D.
12MP7-MPBXPKDUH-V-SSP 12MP7-MPBXPKUH-V-SSP
16MP7-MPBXPKDUH-V-SSP 16MP7-MPBXPKUH-V-SSP
Locking Devices – Add suffix “-LD” to the end of the part number.
Example: 9MP7-MPBLPKH-V-SS-LD
Dimensions in inches are for reference only, subject to change.
.500 Orifice
Three-Way
33
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Medium Pressure
Valves
Three Way
Ball Valves
MPI™ Medium Pressure Valves
Catalog 4234
Materials of Construction
4
1
2
8
3
5
7
11
Medium Pressure
Valves
19
13
6
7
17
12
7
9
10
16
15
18
14
20
Item #
Description
Material
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Handle
Set Screw
Stop Collar, 180 Degree
Stem
Panel Nut
Bearing Washer
O-ring
Back Up Ring
Ball Seat Assembly
Belleville Washer
Packing Washer
Back Up Washer
Body Bushing
Trunion, 180 Degree
Bottom Bushing
Body
O-ring
O-ring
Seat Gland
Bottom Gland
300 SER. SS
17-4PH-H900
300 SER. SS
17-4PH-H900
300 SER. SS
Peek/30% Glass
Fluorocarbon Rubber
PTFE
316SS/Arlon
302SS
316SS
PTFE
Ampco 45
316SS
Ampco 45
316SS
Fluorocarbon Rubber
Fluorocarbon Rubber
316SS
316SS
34
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Valves
Catalog 4234
How to Order MPB Series Valves
Dimensions in inches are for reference only, subject to change.
The correct part number is easily derived from the following example and ordering chart. The nine product
characteristics required are coded as shown in the chart.
The following example describes an MPB Series, three-way diverter ball valve with a .375" orifice, fluorocarbon
rubber seals, 1/4" MPI medium pressure inverted connections on all ports and the optional lock out device.
-
MPBXPKDH
- V -SSP- LD
–
Inlet/Outlet
Connection
Connection
Type
Size
Inlet / Outlet
Connection
Connection
Type
Size
FFemale
2*
4
6
8
9**
12
16
1/8"
1/4"
3/8"
1/2"
9/16"
3/4"
1"
–
Valve
Series
–
Seat Three-Way
Material Valve Type
Orifice
Size
Valve
Series
Seat
Material
Orifice
Size
Packing
Material
Body
Material
MPB
PKPEEK
Blank.187"
H.375"
UH.500"
V***Fluorocarbon
Rubber
KZHighly
Fluorinated
Fluorocarbon
Rubber
BNNitrile
Rubber
EPREthylene
Propylene
Rubber
SSPStainless
Steel
Pipe
MP7Parker
MPI™
MFFemale
Cone &
Thread
Valve
Type
–
Valve
Type
L2-Way
X3-Way
Three-Way
Valve Type
BlankSelector
DDiverter
*Female
Pipe Only
**MP7 and
MF only
Seal
Material
Body
Material
Options
Options
(See Below)
LD Lock out Device
SRH Spring Return
Handle
ACTActuated
***Standard packing
material
How to Order Options
Lock Out Devices – add the suffix -LD to the end of the part number to order factory mounted on the valve.
Actuated – Contact factory for options.
35
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Medium Pressure
Valves
Example:
4MP7
MPI™ Medium Pressure Valves
Catalog 4234
MPF Series Filters
Parker MPF series filters utilize sintered stainless steel filter discs to trap particles from 0.5 to 100 micron sizes.
Inline filters help protect valuable equipment in the process line.
Inline Filters
Medium Pressure
Valves
Tubing
Parker
Part Number
Pressure
psi
Connection
Orifice
Inch
Filter Micron Size Available
Thickness
Inch
0.50
2
5
10
40
100
Length
Inch
1/4" O.D.
4MP7-MPFL-*-SS
15,000
1/4" MPI
0.125
5.25
1.38
3/8" O.D.
6MP7-MPFL-*-SS
15,000
3/8" MPI
0.219
5.25
1.38
1/2" O.D.
8MP7-MPFL-*-SS
15,000
1/2" MPI
0.359
5.25
1.38
9/16" O.D. 9MP7-MPFL-*-SS
15,000
9/16" MPI
0.359
5.25
1.38
*Insert Filter Micron size here. This portion of the part number may be one, two or three digits.
For example: 4PM7-MPFL-100-SS uses the 100 micron size filter.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Dimensions in inches are for reference only, subject to change.
5
2
4
3
6
1
3
Materials of Construction
Item #
Part
Material
1
2
3
4
5
6
Cap
Sealing
Body
Spacer
100 Micron Filter Disc
O-ring
316SS
316SS
316SS
316SS
316SS
PTFE
36
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
*
*
*
*
MPI™ Medium Pressure Valves
Catalog 4234
MPC and MPCB Series Check Valves
Parker MPC and MPCB series check valves are designed for uni-directional flow control of fluids and gases up to
20,000 psi.
Poppet Check Valves
Tubing
Ball Check Valve
Part No.
Poppet Check Valve
Part No.
psi
Connection
Orifice
Inches
Length
Inches
Thickness
Inches
CV
1/4" O.D.
3/8" O.D.
1/2" O.D.
9/16" O.D.
3/4" O.D.
1" O.D.
4MP7-MPCBL-5-SS
6MP7-MPCBL-5-SS
8MP7-MPCBL-5-SS
9MP7-MPCBL-5-SS
12MP7-MPCBL-5-SS
16MP7-MPCBL-5-SS
4MP7-MPCL-5-V-SS
6MP7-MPCL-5-V-SS
8MP7-MPCL-5-V-SS
9MP7-MPCL-5-V-SS
12MP7-MPCL-5-V-SS
16MP7-MPCL-5-V-SS
15,000
15,000
15,000
15,000
15,000
12,500
1/4" MPI
3/8" MPI
1/2" MPI
9/16" MPI
3/4" MPI
1" MPI
0.125
0.219
0.359
0.359
0.438
0.563
4.16
4.16
5.13
4.50
5.13
6.50
1.00
1.00
1.38
1.38
1.75
2.50
0.41
0.62
1.47
1.47
4.01
4.78
Dimensions in inches are for reference only, subject to change.
Ball Check Valves
2
Materials of Construction
1
4
3
5
Item #
Part
Material
1
2
3
4
5
6
Cap
Body
3/8 Ball
Gasket
Ball Support
Spring
316SS
316SS
316SS
316SS
316SS
316SS
6
Poppet Check Valves
2
3
4
Materials of Construction
5
6
1
Item #
Part
Material
1
2
3
4
5
6
Cap
Body
O-Ring
Gasket
Poppett
Spring
316SS
316SS
Fluorocarbon Rubber*
316SS
316SS
316SS
*Optional Seal Materials
KZ Highly Fluorinated Fluorocarbon Rubber
BN Nitrile Rubber
EPR Ethylene Propylene Rubber
37
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Medium Pressure
Valves
Ball Check Valves
MPI™ Medium Pressure Valves
Catalog 4234
MPR Series Relief Valves
Parker MPR series relief valves are offered in preset pressure relief ranges from 1500 to 20,999 psi. Relief valves
are tagged with the proper factory preset pressures.
Relief Valves (Factory Set)
Parker Part Number
Pressure Rating
PSI
Connection
Orifice
Inch
Max Flow Capacity
GPM
8M8F-MPRA-****-SS
8M8F-MPRA-****-SS
9HF8F-MPRA-****-SS
1,500 to 2,999
3,000 to 10,999
11,000 to 20,999
1/2" M X F NPT
1/2" M X F NPT
9HF X 1/2" F NPT
0.250
0.250
0.188
13
25
20
Dimensions in inches are for reference only, subject to change.
Medium Pressure
Valves
13
4
1
2
3
5
7
5
6
9
8
10
6
14
12
11
Materials of Construction
Item #
Qty
Part
Material
1
2
3
4
5
6
7
8
9
10
11
1
1
1
1
2
2
1
1
1
1
1
12
1
13
14
1
1
Cap
5/8-11 X 3 Soc Set Scr
Pressure Rating Tag
Nut
Spring Seat
5/16 Ball
Spring Housing
O-Ring
Stem
Body
Removable Seat Gland
Seal Ring 1500 to 2999
Seal Ring 3000 to 10999
Seal Ring 11000 to 20999
Danly Spring
Stem Seat
303SS
304SS
300 Ser. SS
303SS
304SS
316SS
304SS
Fluorocarbon Rubber*
17-4PH-H1150
316SS
316SS
316SS
316SS
316SS
Steel
17-4PH-H900
*Optional Seal Materials
KZ
BN
EPR
Highly Fluorinated Fluorocarbon Rubber
Nitrile Rubber
Ethylene Propylene Rubber
Example: 8M8F-MPRA-10000-KZ-SS
38
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
MPI™ Medium Pressure Valves
Catalog 4234
HB4 Series Ball Valves
Parker HB4 Series Ball Valves are engineered and manufactured to provide reliable shut-off or switching functions.
Their compact and rugged design incorporates spring-loaded seats for high cycle life and low operating torques
at pressures up to 10,000 psi (689 bar). Every HB4 Series Ball Valve is manufactured with Parker SUPARCASE®
trunnions and ball to resist corrosion, seizures, and particle abrasion.
Specifications
Flow Data
204°C)
Body material:
Stainless Steel
Body configurations: Two-way and Three-way
10,000 psi (689 bar) CWP
with PEEK (PKR) Seats;
6,000 psi (414 bar) CWP
with PCTFE (K) Seats
-65 ˚F to 400 ˚F (-54 ˚C to Two-way HB4L: Cv = 1.02; xT = 0.42; Orifice = 0.188" (4.8 mm)
Three-way HB4X: Cv = 0.62; xT = 0.71; Orifice = 0.188" (4.8 mm)
Tested in accordance with ISA S75.02. Gas flow will be choked when P1 - P2 / P1 = xT .
For additional information about the HB Series of Ball Valves, including flow data and pressure ratings,
see Catalog 4121-HB or contact your authorized Parker Instrumentation Distributor or the Parker Hannifin
Instrumentation Products Division at (256) 435-2130.
Tubing
1/4" O.D.
3/8" O.D.
9/16" O.D.
Parker Part No. 2-Way
Parker Part No. 3-Way
HB4PKR-SSP
HB6PKR-SSP
HB9PKR-SSP
4MP7-HB4XPKR-SSP
6MP7-HB4XPKR-SSP
9MP7-HB4XPKR-SSP
Dimensions in inches are for reference only, subject to change.
4MP7-HB4LPKR-SSP
39
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Medium Pressure
Valves
Pressure rating:
Temperature rating:
MPI™ Medium Pressure Valves
Catalog 4234
15,000 PSI, Ultra High Flow Ball Valves
Parker’s High Flow Ball Valve provides high flow rates without sacrificing working
pressures. The 2507 Super Duplex body provides the strength necessary for
medium pressure applications. End connections are Parker’s MPI™ (Medium
Pressure Inverted) fittings which allows for quick installation and dependable
service. Parker’s Parofluor™ V8588-90 perfluorinated elastomer seals resist the
aggressive chemical media common to the oil and gas industries. (See Parker
O-Ring Division Technical Bulletin No. 5722B1-USA for complete details and test
data.)
Medium Pressure
Valves
Features
Specifications
• Bi-directional trunnion style closure
• Blow out proof stem
• Optional packing, seal, spring, and seat
materials available (consult factory for available
options)
• 4 hole rack mount bolt pattern
• For applications up to 15,000 PSI
• .47" Orifice for high flow
Working Pressure
Orifice
Standard Connections
Weight
Typical Application
Typical Materials
up to 15,000 PSI
.47" (10 mm)
Parker MPI™ Fittings
6.25kg
Chemical Injection Skids
• 316 cold-worked stainless steel trim
• 2507 Super Duplex body
• Fiber-reinforced PEEK seats
• Parker Parofluor™ perfluorinated elastomer seals
Materials of Construction
Item #
40
Description
Material
1
Body
Duplex 2507
2
Stem
Inconel 625
3
Bearing Washer
Nitronic 60
4
UNIF-112 O-Ring
V8588-90
5
UNIF-112 Backup Ring
PEEK
6
Top Bearing
Nitronic 60
7
Trunnion
316L SS CW
8
Bottom Blank
316L SS CW
9
Bottom Bearing
Nitronic 60
10
UNIF-215 O-Ring
V8588-90
11
Seat Retainer
17-4 PH H900
12
Seat Seal
30% GF PEEK
13
Spring Washer
Inconel 718
14
Follower
316L SS CW
15
UNIF-113 Backup Ring
PEEK
16
UNIF-113 O-Ring
V8588-90
17
End Adapter / # 12MPI
316L SS CW
18
Socket Head Cap Screw
316 SS
19
Hub
316L SS CW
20
Knurled Set Screw
18-8 SS
21
Thread Disc
Nylatron
22
Handle
316L SS CW
23
Handle Grip
PVC
24
Socket Set Screw
18-8 SS
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Medium Pressure
Valves
MPI™ Medium Pressure Valves
Catalog 4234
Dimensions
Parker
Part Number
PSI
Connection
Orifice
12MP7-MPBLPKPUH-KZ*-SSP
16MP7-MPBLPKPUH-KZ*-SSP
15,000
12,500
3/4" MPI
1" MPI
0.470
0.470
Size
Ultra High Flow (UH)
3/4"
1"
Inches
Minimum
Orifice
0.470
0.470
Cv
A
7.6
7.6
8.51
10.13
* Perfluorinated elastomer is standard. Please consult the factory for optional materials.
Dimensions in inches are for reference only, subject to change.
Tee Handle Option*
Dimensions
Dimensions in inches are for reference only, subject to change.
Materials of Construction
(Items 1-21 same as standard part, shown on previous page)
Item # Description
22
Handle**
23
Handle Grip
Material
316L SS CW
PVC
* To order the Stainless Steel Tee Handle option, add “-ST” to the end of the part number.
41
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Technical Information
Catalog 4234
Assembly
1. Parker MPI™ Fittings are sold completely assembled and ready for
immediate use. Simply insert the tube as illustrated until it bottoms in the
fitting body. (If the fitting is disassembled, note that the small tapered end of
the ferrule(s) go into the fitting body.)
2. Turn the nut to the “finger-tight” position. Hold the fitting body with a second
wrench to prevent the body from turning as you tighten the nut. For hand
assembly, tighten the nut 1-1/2 turns. For 3/4" and 1" sizes, preset the nut
and ferrules and then tighten the nut 1/2 turn only. See page 43 for more
information on preset connections. Parker recommends that you mark the
nut (using a scribe or ink) to help you count the turns.
Technical
Information
Gaugeability
Check the gap between the nut and the body hex with the end of the gauge by
inserting the gauge (as shown) into the beveled gap between the nut and body
hex. Gently turn the gauge (that is, it “twists out”). However, if the gauge slides
into the beveled gap, (does not “twist out”) the fitting is not properly made up
and you must check the entire assembly procedure.
Remake
For maximum number of remakes, mark the fitting and nut before disassembly.
Before retightening, make sure the assembly has been inserted into the
fitting until the ferrule seats in the fitting. Retighten the nut by hand. Rotate the
nut with a wrench to the original position as indicated by the previous marks
lining up. (A noticeable increase in mechanical resistance will be felt indicating
the ferrule is being re-sprung into sealing position.)
42
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Technical Information
Catalog 4234
MPI™ Hydraulic Preset Tools
MPI™ Body Die
MPI™ Nut Die
Body Dies and Nut Dies Used with the MPI™ Small Preset Assembly
MPI Small Preset Assembly
Inches
Body Die
Part No.
Nut Die
Part No.
A
B
D
4 MPI Body Die
4 MPI Nut Die
.50
1.25
1.62
P
MPI™
Nut Size
Preset
Pressure
(PSIG)
1.20
4
3,200
6 MPI Body Die
6 MPI Nut Die
.63
1.25
1.62
1.20
6
4,000
8 MPI Body Die
8 MPI Nut Die
.82
1.25
1.62
1.20
8
6,800
9 MPI Body Die
9 MPI Nut Die
.88
1.25
1.62
1.20
9
8,500
Dimensions in inches are for reference only, subject to change.
Technical
Information
Parker Part No.
MPI SMALL Preset Assembly
Body Dies and Nut Dies Used with the MPI™ Large Preset Assembly
MPI Large Preset Assembly
Inches
P
MPI™
Nut Size
Preset
Pressure
(PSIG)
1.67
9
3,600
2.00
1.67
12
5,100
2.00
1.67
16
8,000
Body Die
Part No.
Nut Die
Part No.
A
B
D
*9 MPI Body Die
9 MPI Large Nut Die
.88
1.25
2.00
12 MPI Body Die
12 MPI Nut Die
1.13
1.75
16 MPI Body Die
16 MPI Nut Die
1.44
1.75
* Requires a 9 MPI Body Die Adapter
Parker Part No.
MPI LARGE Preset Assembly
Dimensions in inches are for reference only, subject to change.
Parker Part No.
MPI AIR PUMP KIT
Parker Part No.
MPI HAND PUMP KIT
Note: One Pump Kit, Preset Assembly, Body Die and Nut Die are required for presetting. Pump Kits and Preset
Assemblies can be interchanged but Body Dies and Nut Dies are for a specific Preset Assembly. Detailed
operating instructions are included with each kit. Copies may also be obtained by contacting the Division.
43
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Notes
Catalog 4234
44
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Notes
Catalog 4234
45
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Notes
Catalog 4234
46
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Offer of Sale
Catalog 4234
Terms of Sale with Warranty Limitations
The items described in this document and other documents and descriptions provided by Parker Hannifin Corporation, its
subsidiaries and its authorized distributors (“Seller”) are hereby offered for sale at prices to be established by Seller. This offer
and its acceptance by any customer (“Buyer”) shall be governed by all of the following Terms and Conditions. Buyer’s order
for any item described in its document, when communicated to Seller verbally, or in writing, shall constitute acceptance of this
offer. All goods or work described will be referred to as “Products”.
1. Terms and Conditions. Seller’s willingness to offer
Products, or accept an order for Products, to or from Buyer is
expressly conditioned on Buyer’s assent to these Terms and
Conditions and to the terms and conditions found on-line at
www.parker.com/saleterms/. Seller objects to any contrary
or additional term or condition of Buyer’s order or any other
document issued by Buyer.
be allowed unless asserted in writing within 60 days after
delivery or, in the case of an alleged breach of warranty,
within 30 days after the date within the warranty period on
which the defect is or should have been discovered by Buyer.
Any action based upon breach of this agreement or upon
any other claim arising out of this sale (other than an action
by Seller for any amount due to Seller from Buyer) must be
commenced within thirteen months from the date of tender
of delivery by Seller or, for a cause of action based upon
an alleged breach of warranty, within thirteen months from
the date within the warranty period on which the defect is or
should have been discovered by Buyer.
2. Price Adjustments; Payments. Prices stated on the
reverse side or preceding pages of this document are valid
for 30 days. After 30 days, Seller may change prices to reflect
any increase in its costs resulting from state, federal or local
legislation, price increases from its suppliers, or any change
in the rate, charge, or classification of any carrier. The prices
stated on the reverse or preceding pages of this document
do not include any sales, use, or other taxes unless so stated
specifically. Unless otherwise specified by Seller, all prices
are F.O.B. Seller’s facility, and payment is due 30 days from
the date of invoice. After 30 days, Buyer shall pay interest
on any unpaid invoices at the rate of 1.5% per month or the
maximum allowable rate under applicable law.
6. LIMITATION OF LIABILITY. UPON NOTIFICATION,
SELLER WILL, AT ITS OPTION, REPAIR OR REPLACE A
DEFECTIVE PRODUCT, OR REFUND THE PURCHASE
PRICE. IN NO EVENT SHALL SELLER BE LIABLE TO
BUYER FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF, OR AS
THE RESULT OF, THE SALE, DELIVERY, NON-DELIVERY,
SERVICING, USE OR LOSS OF USE OF THE PRODUCTS
OR ANY PART THEREOF, OR FOR ANY CHARGES OR
EXPENSES OF ANY NATURE INCURRED WITHOUT
SELLER’S WRITTEN CONSENT, EVEN IF SELLER HAS
BEEN NEGLIGENT, WHETHER IN CONTRACT, TORT OR
OTHER LEGAL THEORY. IN NO EVENT SHALL SELLER’S
LIABILITY UNDER ANY CLAIM MADE BY BUYER EXCEED
THE PURCHASE PRICE OF THE PRODUCTS.
3. Delivery Dates; Title and Risk; Shipment. All delivery
dates are approximate and Seller shall not be responsible
for any damages resulting from any delay. Regardless of the
manner of shipment, title to any products and risk of loss
or damage shall pass to Buyer upon tender to the carrier
at Seller’s facility (i.e., when it’s on the truck, it’s yours).
Unless otherwise stated, Seller may exercise its judgment
in choosing the carrier and means of delivery. No deferment
of shipment at Buyers’ request beyond the respective
dates indicated will be made except on terms that will
indemnify, defend and hold Seller harmless against all loss
and additional expense. Buyer shall be responsible for any
additional shipping charges incurred by Seller due to Buyer’s
changes in shipping, product specifications or in accordance
with Section 13, herein.
7. Contingencies. Seller shall not be liable for any default
or delay in performance if caused by circumstances beyond
the reasonable control of Seller.
8. User Responsibility. The user, through its own analysis
and testing, is solely responsible for making the final
selection of the system and Product and assuring that all
performance, endurance, maintenance, safety and warning
requirements of the application are met. The user must
analyze all aspects of the application and follow applicable
industry standards and Product information. If Seller provides
Product or system options, the user is responsible for
determining that such data and specifications are suitable
and sufficient for all applications and reasonably foreseeable
uses of the Products or systems.
4. Warranty. Seller warrants that the Products sold hereunder shall be free from defects in material or workmanship for
a period of twelve months from the date of delivery to Buyer
or 2,000 hours of normal use, whichever occurs first. This
warranty is made only to Buyer and does not extend to anyone
to whom Products are sold after purchased from Seller. The
prices charged for Seller’s products are based upon the
exclusive limited warranty stated above, and upon the following
disclaimer: DISCLAIMER OF WARRANTY: THIS WARRANTY
COMPRISES THE SOLE AND ENTIRE WARRANTY
PERTAINING TO PRODUCTS PROVIDED HEREUNDER.
SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS
AND IMPLIED, INCLUDING MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
5. Claims; Commencement of Actions. Buyer shall
9. Loss to Buyer’s Property. Any designs, tools, patterns,
materials, drawings, confidential information or equipment
furnished by Buyer or any other items which become Buyer’s
property, may be considered obsolete and may be destroyed
by Seller after two consecutive years have elapsed without
Buyer placing an order for the items which are manufactured
using such property. Seller shall not be responsible for
any loss or damage to such property while it is in Seller’s
possession or control.
promptly inspect all Products upon delivery. No claims for
shortages will be allowed unless reported to the Seller
within 10 days of delivery. No other claims against Seller will
10. Special Tooling. A tooling charge may be imposed for
any special tooling, including without limitation, dies, fixtures,
molds and patterns, acquired to manufacture Products.
47
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Offer of Sale
Catalog 4234
by written notice immediately terminate this agreement for
the following: (a) Buyer commits a breach of any provision of
this agreement (b) the appointment of a trustee, receiver or
custodian for all or any part of Buyer’s property (c) the filing of
a petition for relief in bankruptcy of the other Party on its own
behalf, or by a third party (d) an assignment for the benefit of
creditors, or (e) the dissolution or liquidation of the Buyer.
Such special tooling shall be and remain Seller’s property
notwithstanding payment of any charges by Buyer. In no event
will Buyer acquire any interest in apparatus belonging to Seller
which is utilized in the manufacture of the Products, even if
such apparatus has been specially converted or adapted for
such manufacture and notwithstanding any charges paid by
Buyer. Unless otherwise agreed, Seller shall have the right to
alter, discard or otherwise dispose of any special tooling or
other property in its sole discretion at any time.
18. Governing Law. This agreement and the sale and
delivery of all Products hereunder shall be deemed to have
taken place in and shall be governed and construed in
accordance with the laws of the State of Ohio, as applicable to
contracts executed and wholly performed therein and without
regard to conflicts of laws principles. Buyer irrevocably agrees
and consents to the exclusive jurisdiction and venue of the
courts of Cuyahoga County, Ohio with respect to any dispute,
controversy or claim arising out of or relating to this agreement.
Disputes between the parties shall not be settled by arbitration
unless, after a dispute has arisen, both parties expressly agree
in writing to arbitrate the dispute.
11. Buyer’s Obligation; Rights of Seller. To secure
payment of all sums due or otherwise, Seller shall retain a
security interest in the goods delivered and this agreement
shall be deemed a Security Agreement under the Uniform
Commercial Code. Buyer authorizes Seller as its attorney
to execute and file on Buyer’s behalf all documents Seller
deems necessary to perfect its security interest. Seller shall
have a security interest in, and lien upon, any property of
Buyer in Seller’s possession as security for the payment of
any amounts owed to Seller by Buyer.
12. Improper use and Indemnity. Buyer shall indemnify,
defend, and hold Seller harmless from any claim, liability,
damages, lawsuits, and costs (including attorney fees),
whether for personal injury, property damage, patent,
trademark or copyright infringement or any other claim,
brought by or incurred by Buyer, Buyer’s employees, or any
other person, arising out of: (a) improper selection, improper
application or other misuse of Products purchased by Buyer
from Seller; (b) any act or omission, negligent or otherwise,
of Buyer; (c) Seller’s use of patterns, plans, drawings, or
specifications furnished by Buyer to manufacture Product; or
(d) Buyer’s failure to comply with these terms and conditions.
Seller shall not indemnify Buyer under any circumstance
except as otherwise provided.
19. Indemnity for Infringement of Intellectual Property
Rights. Seller shall have no liability for infringement of
any patents, trademarks, copyrights, trade dress, trade
secrets or similar rights except as provided in this Section.
Seller will defend and indemnify Buyer against allegations
of infringement of U.S. patents, U.S. trademarks, copyrights,
trade dress and trade secrets (“Intellectual Property Rights”).
Seller will defend at its expense and will pay the cost of any
settlement or damages awarded in an action brought against
Buyer based on an allegation that a Product sold pursuant to
this Agreement infringes the Intellectual Property Rights of a
third party. Seller’s obligation to defend and indemnify Buyer is
contingent on Buyer notifying Seller within ten (10) days after
Buyer becomes aware of such allegations of infringement, and
Seller having sole control over the defense of any allegations or
actions including all negotiations for settlement or compromise.
If a Product is subject to a claim that it infringes the Intellectual
Property Rights of a third party, Seller may, at its sole expense
and option, procure for Buyer the right to continue using
the Product, replace or modify the Product so as to make it
noninfringing, or offer to accept return of the Product and return
the purchase price less a reasonable allowance for depreciation.
Notwithstanding the foregoing, Seller shall have no liability
for claims of infringement based on information provided by
Buyer, or directed to Products delivered hereunder for which the
designs are specified in whole or part by Buyer, or infringements
resulting from the modification, combination or use in a system
of any Product sold hereunder. The foregoing provisions of
this Section shall constitute Seller’s sole and exclusive liability
and Buyer’s sole and exclusive remedy for infringement of
Intellectual Property Rights.
13. Cancellations and Changes. Orders shall not be
subject to cancellation or change by Buyer for any reason,
except with Seller’s written consent and upon terms that
will indemnify, defend and hold Seller harmless against all
direct, incidental and consequential loss or damage. Seller
may change product features, specifications, designs and
availability with notice to Buyer.
14. Limitation on Assignment. Buyer may not assign its
rights or obligations under this agreement without the prior
written consent of Seller.
15. Entire Agreement. This agreement contains the entire
agreement between the Buyer and Seller and constitutes
the final, complete and exclusive expression of the terms of
the agreement. All prior or contemporaneous written or oral
agreements or negotiations with respect to the subject matter
are herein merged.
16. Waiver and Severability. Failure to enforce any
provision of this agreement will not waive that provision nor
will any such failure prejudice Seller’s right to enforce that
provision in the future. Invalidation of any provision of this
agreement by legislation or other rule of law shall not invalidate
any other provision herein. The remaining provisions of this
agreement will remain in full force and effect.
20. Taxes. Unless otherwise indicated, all prices and
charges are exclusive of excise, sales, use, property,
occupational or like taxes which may be imposed by any taxing
authority upon the manufacture, sale or delivery of Products.
21. Equal Opportunity Clause. For the performance of
government contracts and where dollar value of the Products
exceed $10,000, the equal employment opportunity clauses
in Executive Order 11246, VEVRAA, and 41 C.F.R. §§ 601.4(a), 60-741.5(a), and 60-250.4, are hereby incorporated.
17. Termination. This agreement may be terminated by
Seller for any reason and at any time by giving Buyer thirty
(30) days written notice of termination. In addition, Seller may
01/09
48
Parker Hannifin Corporation
Instrumentation Products Division
Huntsville, AL USA
www.parker.com/ipdus
Parker’s Motion & Control Technologies
At Parker, we’re guided by
a relentless drive to help
our customers become more
productive and achieve
higher levels of profitability by engineering the best
systems for their requirements. It means looking at
customer applications from
many angles to find new
ways to create value. Whatever the motion and control
technology need, Parker has
the experience, breadth of
product and global reach
to consistently deliver. No
company knows more about
motion and control technology than Parker. For further
info call 1-800-C-Parker.
AEROSPACE
Key Markets
• Aircraft engines
• Business & general aviation
• Commercial transports
• Land-based weapons systems
• Military aircraft
• Missiles & launch vehicles
• Regional transports
• Unmanned aerial vehicles
Key Products
• Flight control systems
& components
• Fluid conveyance systems
• Fluid metering delivery
& atomization devices
• Fuel systems & components
• Hydraulic systems & components
• Inert nitrogen generating systems
• Pneumatic systems & components
• Wheels & brakes
FLUID & GAS HANDLING
Key Markets
• Aerospace
• Agriculture
• Bulk chemical handling
• Construction machinery
• Food & beverage
• Fuel & gas delivery
• Industrial machinery
• Mobile
• Oil & gas
• Transportation
• Welding
HYDRAULICS
Key Markets
• Aerospace
• Aerial lift
• Agriculture
• Construction machinery
• Forestry
• Industrial machinery
• Mining
• Oil & gas
• Power generation & energy
• Truck hydraulics
Key Products
• Brass fittings & valves
• Diagnostic equipment
• Fluid conveyance systems
• Industrial hose
• PTFE & PFA hose, tubing &
plastic fittings
• Rubber & thermoplastic hose
& couplings
• Tube fittings & adapters
• Quick disconnects
Key Products
• Diagnostic equipment
• Hydraulic cylinders
& accumulators
• Hydraulic motors & pumps
• Hydraulic systems
• Hydraulic valves & controls
• Power take-offs
• Rubber & thermoplastic hose
& couplings
• Tube fittings & adapters
• Quick disconnects
CLIMATE CONTROL
Key Markets
• Agriculture
• Air conditioning
• Food, beverage & dairy
• Life sciences & medical
• Precision cooling
• Processing
• Transportation
Key Products
• CO2 controls
• Electronic controllers
• Filter driers
• Hand shut-off valves
• Hose & fittings
• Pressure regulating valves
• Refrigerant distributors
• Safety relief valves
• Solenoid valves
• Thermostatic expansion valves
PNEUMATICS
Key Markets
• Aerospace
• Conveyor & material handling
• Factory automation
• Life science & medical
• Machine tools
• Packaging machinery
• Transportation & automotive
Key Products
• Air preparation
• Brass fittings & valves
• Manifolds
• Pneumatic accessories
• Pneumatic actuators & grippers
• Pneumatic valves & controls
• Quick disconnects
• Rotary actuators
• Rubber & thermoplastic hose
& couplings
• Structural extrusions
• Thermoplastic tubing & fittings
• Vacuum generators, cups & sensors
ELECTROMECHANICAL
Key Markets
•Aerospace
• Factory automation
• Life science & medical
• Machine tools
• Packaging machinery
• Paper machinery
• Plastics machinery & converting
• Primary metals
• Semiconductor & electronics
• Textile
• Wire & cable
Key Products
• AC/DC drives & systems
• Electric actuators, gantry robots
& slides
• Electrohydrostatic actuation systems
• Electromechanical actuation systems
• Human machine interface
• Linear motors
• Stepper motors, servo motors,
drives & controls
• Structural extrusions
PROCESS CONTROL
Key Markets
• Chemical & refining
• Food, beverage & dairy
• Medical & dental
• Microelectronics
• Oil & gas
• Power generation
Key Products
• Analytical sample
conditioning products
& systems
• Fluoropolymer chemical
delivery fittings, valves
& pumps
• High purity gas delivery
fittings, valves & regulators
• Instrumentation fittings,
valves & regulators
• Medium pressure fittings
& valves
• Process control manifolds
FILTRATION
Key Markets
• Food & beverage
• Industrial machinery
• Life sciences
• Marine
• Mobile equipment
• Oil & gas
• Power generation
• Process
• Transportation
Key Products
• Analytical gas generators
• Compressed air & gas filters
• Condition monitoring
• Engine air, fuel & oil filtration
& systems
• Hydraulic, lubrication &
coolant filters
• Process, chemical, water
& microfiltration filters
• Nitrogen, hydrogen & zero
air generators
SEALING & SHIELDING
Key Markets
• Aerospace
• Chemical processing
• Consumer
• Energy, oil & gas
• Fluid power
• General industrial
• Information technology
• Life sciences
• Military
• Semiconductor
• Telecommunications
• Transportation
Key Products
• Dynamic seals
• Elastomeric o-rings
• EMI shielding
• Extruded & precision-cut,
fabricated elastomeric seals
• Homogeneous & inserted elastomeric
shapes
• High temperature metal seals
• Metal & plastic retained composite
seals
• Thermal management
Sales Offices Worldwide
Parker Hannifin Corporation
Instrumentation Products Division
1005 A Cleaner Way
Huntsville, AL 35805
USA
phone 256 881 2040
fax 256 881 5072
www.parker.com/ipdus
Parker Hannifin Corporation
Instrumentation Products Division
2651 Alabama Highway 21 North
Jacksonville, AL 36265-9681
USA
phone 256 435 2130
fax 256 435 7718
www.parker.com/ipdus
Parker Hannifin Corporation
Instrumentation Products Division
Autoclave Engineers Operation
8325 Hessinger Drive
Erie, PA 16509-4679
USA
phone 814 860 5700
fax 814 838 5811
http://www.autoclave.com
Parker Hannifin plc
Instrumentation Products Division
Riverside Road
Pottington Business Park
Barnstaple, Devon EX31 1NP
England
phone +44 0 1271 313131
fax +44 0 1271 373636
email [email protected]
www.parker.com/ipdus
Catalog 4234 15M February 2012 Duke
Parker Hannifin Corporation
Instrumentation Products Division
1005 A Cleaner Way
Huntsville, AL 35805
phone 256 881 2040
fax 256 881 5072
www.parker.com/ipdus
Your Local Authorized Parker Distributor