Coco Bunk Bed
Code: 3322
IMPORTANT-READ CAREFULLY-RETAIN FOR FUTURE REFERENCE
Welcome
Care of your Product
Thank you for buying the Coco Bunk.
Before beginning assembly, please take a few quiet minutes to read these instructions.
Lay the parts out on a clean, soft, flat surface (such as a carpeted floor) and compare with the parts
check list on the next page. Do not throw away any packaging until you are sure that you have all the
parts.
If, for any reason, you wish to return the product, you must disassemble the components and use the
original packaging.
The product must be assembled by an adult. There are small parts: keep small children clear of the
assembly area. Some stages of assembly require more than one person.
This product is designed to conform to BSEN747:1 2012
The MAXIMUM thickness of the UPPER BUNK mattress is 16cm.
This information is identified on the product label fitted to the bed.
The recommended size of the mattress is 191cm x 90cm (6`3” x 3`0)
3. Attach the Drawer Base.
You need: 7x Screws for Carcass (35mm) and a Screwdriver.
Ensure the Drawer frame is square and carefully fit the Draw Base. The lip of the Base locates
into the groove on the back of the Front. Once in position and all holes are aligned correctly,
secure the Base to the Drawer Frame using 7x Screws (35mm) (as shown below).
Product Care
Clean your Bunk by wiping with a damp cloth & drying with a soft cloth. Never clean with abrasives,
chemical cleaner or household polishes.
Take care when handling or moving the furniture. Careless handling can damage wooden furniture, Try
to lift rather than drag.
Product Safety
Periodically check that all assembly fastenings are tightened properly, care should be taken to ensure
that no fittings are loose.
The furniture must be set up on an even and stable surface..
Keep away from direct sources of heat, such as electric, gas or coal fires.
Do not allow children to climb on the furniture. Using this furniture other than for its intended purpose
could cause damage to the structure or serious injury to your child.
The Bunk should not be used if any structural part is broken or missing
The upper bunk is not suitable for children under six years old due to the risk of falls
Do not attach items such as ropes, strings, cords, harnesses or belts etc to avoid the risk of
strangulation.
Warning: Children can become trapped between the bed and the wall. To avoid the risk of serious
injury the distance between the top safety barrier and the wall must not exceed 75mm or be more than
230mm.
4. Fit the Castors.
You Need: 8x Screws for Castors (12mm), 4x Castors and a Screwdriver.
Carefully turn the Drawer over and attach the 4x Castors to the Base with the 8x Screws
(12mm) as shown below. Finally turn the Drawer over and carefully slide it under the Bed.
Customer Service 0345 872 2400
If you have a problem with this product, please call our Customer Service Team who will be
glad to help.
We can usually provide replacement and / or spare parts promptly; it will help us if you can
identify the specific part using the check list in the next section.
About ASPACE
Most of us at ASPACE are parents too, so we know how important it is to give children a
comfortable, secure and individual space where they can sleep, learn and play. We’ve been
kitting out children’s bedrooms with clever furniture ideas for over 20 years, with every bunk
ladder, wardrobe door and bookshelf designed by our team in the UK.
Most of us at ASPACE are parents too, so we know how important it is to give children a
ladder, wardrobe door and bookshelf designed by our team in the UK.
ASPACE bedrooms are packed with creativity, fun and inspiration; from gorgeous bedroom
sets and beautiful bedding, to clever storage and creative accessories, we make sure
1 everything we sell is built to last, and delivered with love.
Please now recheck that all fittings are properly tightened. Repeat stages 1-4 of the drawer
assembly for each drawer.
10
Assembly Per Drawer
(Stages 1-4 apply to both Drawers)
1. Fit the Sides to the Drawer Fronts.
Parts Check List
CR
Bed Parts and Fittings
You Need: 4x Cam Pins, 4x Cams and a Screwdriver.
1x Lower Back Mattress Rail
Fit 4x cam pins into each drawer front using a screwdriver. Place two drawer sides onto each
drawer front (cam holes facing inwards) ensuring that all cam pins and dowels are correctly
engaged into their corresponding holes. Once in position, insert 4x Cams into the large holes
on the inside faces of the sides ensuring that arrows on cams point towards their
corresponding Cam Pins.
1x Lower Front Mattress Rail
1x Front Guard Rail
1x Upper Front Mattress Rail
1x Upper Back Mattress Rail
2x Ends
(Left hand side)
2x Ends
(Right hand side)
1x Long Ladder leg
2x Mattress Bases
1x Short Ladder leg
4x Feet
16x Bolts (16mm)
4x Battens
26x Euro Screws (16mm)
3x Brackets
16x Bolts (45mm)
3x Ladder Treads
12x Bolts (35mm)
3x Bracket Covers
4x Connecting Bolts
with Nuts and angled washers
14x Large Dowels
2. Attach the Drawer Back.
3x Cams
1x Spanner
You Need: 4x Screw Bolts (40mm) and an Allen key.
Insert the Drawer Back by slightly leaning the Drawer Sides outwards. Pre-fitted Dowels in the
Back must be located into the corresponding holes on the inside face of each Drawer Side.
NOTE: The Cams that attach the Drawer Fronts to the Sides can be loosened to make it
easier to fit the Back.
Once in position, fit the 4x screw bolts (40mm) as shown below to secure the back to the
Sides.
1x Allen Key
3x Cam Pins
68x Screws for Mattress Base (25mm)
You will also need a screwdriver
Under Drawer Parts and Fittings
2x Drawer Fronts
8x Screw Bolts (40mm)
8x Cam Pins
4x Drawer Sides (Left & Right)
8x Cams
16x Screws for castors (12mm)
14x Screws for carcass (35mm)
9
2x Drawer Backs
2x Drawer Bases
8x Castors
2
Assembly
8. Attach the Ladder .
1. Assemble the Ends
You need: 6x Bolts (35mm), Allen Key
You need: 14x Large Dowels, 4x Connecting Bolts and Nuts with angled washers,1x Spanner.
Attach the ladder to the Bed using 6x Bolts (35mm) and the Allen key (as shown below).
Lay both sets of Ends (left and Right) on a soft level floor, with the holes facing upwards.
Insert 7x Large Dowels into the inside edges of the sides and attach the halves together.
Insert the 4x Connecting Bolts, Washers and Nuts into the large holes as shown below, fully
tighten to secure the two halves together.
A
B
C
9. Fit the Mattress bases.
You need: 68x Screws and a Screwdriver.
2. Attach The Battens
You need: 16x Bolts (45mm), 1x Allen key, 4x Feet
Lower both Mattress Bases onto the top of the support rails. Spread the slats out evenly on
the mattress support rails, taking particular care that the end slats are placed as near to the
ends as possible.
Use the 68x screws to fix all mattress base slats onto the mattress support rails below.
Some initial pressure will be required for screws to ‘bite’. Please note: For safety reasons the
Top Mattress Base must have every slat screwed down.
Attach the 4x battens to the inside faces of both Ends using 16x Bolts (45mm). Also, simply
push the 4x Feet to the holes on the underside edges of the Ends as shown below.
3
Gentle pressure applied to the centre of the mattress rails, either side,
will help to maintain a uniform width along the length of the bed.(see arrows)
8
7. Construct the Ladder.
You need: 6x Bolts (35mm) and an Allen key
Note: The Ladder must be constructed to suit the Left or Right hand end of the bed. (Left or
Right hand end Ladder orientation shown below). Fit each Tread onto the Ladder legs by
locating the sides of the Treads into the notches on the leg. Ensure the Treads are attached in
the right orientation (as below).
Once Treads are in the correct position secure them to the leg using the 6x Bolts (35mm).
3. Attach one End to the Back Mattress Rails.
You need: 1x Bracket, 1x Bracket Cover, 8x Bolts (16mm), 8x Euro Screws (16mm).
Prepare the Ends by fitting 8x Bolts into the holes on the left and right hand sides, ensure the
bolts are only screwed in half way.
Lay the Upper and Lower Back Mattress Rails on a soft level floor, with the holes and prefitted brackets facing upwards. Using 3x Euro Screws (16mm), fit 1x Bracket to the larger
Upper Mattress Rail (Fig 3.0), then With a minimum of two people carefully lift 1x End and
fit the large key shaped holes in the pre-fitted brackets over the heads of the Bolts in the End
and slide the brackets downwards to fully engage (Fig 3.1). Once both upper and lower Rails
are in position and the brackets are engaged, tighten the Bolts to secure.
Right hand Ladder Construction
3.0
1x Bracket
Left hand Ladder Construction
7
3.1
3.2
3.3
3.4
Secure the bracket to the End using 3x Euro Screws (16mm) (Fig 3.2). Once all the Euro
Screws for the bracket have been tightened, clip on the Bracket cover to conceal it (Fig 3.4).
Also attach 1x Euro Screw (16mm) to add extra strength to each pre-fitted bracket joint (Fig 3.2, Attach one Euro Screw for each Bracket).
5
4
4. Attach the remaining End to the Back Mattress Rails.
6. Attach the Front Guard Rail.
You need: 1x Bracket, 1x Bracket Cover, 8x Bolts (16mm), 8x Euro Screws
You need: 3x Cams, 3x Cam Pins, 6x Euro Screws (16mm),1x Bracket,1x Bracket Cover.
Prepare the remaining End and Repeat the process of attaching the Back Mattress Rails.
(The same process as stage 3)
NOTE: The Guard Rail can be fitted at either end of the Upper Front Rail depending on which
side the Ladder is required.(Assembly shown is for a right hand ladder configuration).
Screw the 3x Cam Pins into the holes on the on the top edge of the Upper Front rail.
Once Cam pins are in position carefully lower the Front Guard Rail onto the heads of the Cam
Pins and into the corresponding holes on the underside edge ensuring that the 3 large holes
on the inside face of the rail point inwards (as shown below).
Fit the 3x Cams into the 3 large holes on the inside face of the guard rail ensuring that the
arrows on the Cams are pointing towards the Cam Pins. Once all is correctly engaged, tighten
the Cams clockwise with a screwdriver to secure the Guard Rail.
Arrow pointing towards Cam Pin.
Tighten Cam Clockwise to secure.
5. Fit the Lower Front Mattress Rail
You need: 4x Bolts (16mm), 2x Euro Screws (16mm)
Fit the Lower Front Mattress Rail to the both assembled bed Ends in exactly the same way as
the Lower Back Rail, engaging the exposed heads of the fitted Bolts into the pre-fitted rail
brackets and securing in position using 2x Euro Screws (16mm) (Refer back to stage 3).
Once the Rail has been fitted, carefully stand the assembly upright (This should only be
attempted with a minimum of two people). Once upright, fit the Upper front mattress rail.
NOTE: The Upper Front Rail must be orientated so that the holes on the edge are facing
upwards (see below).
Once the Front guard rail is in position secure the end of the rail to the End using 1x Bracket
and 6x Euro Screws (16mm) and 1x Bracket Cover. (Same process as on page 5)
Holes in top edge pointing upwards
5
6