Wireless Remote Indicator
Module (RIM)
Programming
including Cause and Effect
Contents
Section
Page No
1.0 INTRODUCTION ................................................................................................... 3
2.0 ADDING A FIRECELL WIRELESS RIM TO A RADIO LOOP MODULE......................... 4
3.0 ADDING A FIRECELL WIRELESS RIM TO A RADIO HUB......................................... 6
4.0 FIRECELL CONFIGURATION TOOL PROGRAMMING............................................... 9
5.0 ADDING AND CONFIGURING A FIRECELL WIRELESS RIM TO A SETUP FILE ....... 11
6.0 CAUSE & EFFECT - LINKING A ZONE OF DEVICES TO A RIM ............................... 13
7.0 CAUSE & EFFECT - LINKING AN INDIVIDUAL DEVICE TO A RIM ......................... 17
8.0 TESTING THE RIM FUNCTIONALITY ................................................................... 21
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
2
1.0 Introduction
The following instruction details the adding of a Wireless Remote Indicator Module to a
Radio Loop Module/Radio Hub and also two methods of programming the cause and
effect rules on the FireCell Wireless Syncro and AS versions of control panel to:
i)
ii)
Linking a zone of devices to a Remote Indicator Module (RIM)
Link a single device to a Remote Indicator Module (RIM)
The instruction has been written for engineers that have completed training on the
FireCell product range and therefore have knowledge of the product and the basic
programming functionality of the control panel.
The instruction therefore assumes that the engineers are practised in the methodology of
removing, editing and sending control panel Loop Explorer setup files to the FireCell
control panel.
Before starting the programming the following items must be available.
•
1x Laptop with FireCell CIE programming software installed ( Loop Explorer
V60020E)
•
1 x FireCell control panel programming lead. Part No. FC-000-KEN
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
3
2.0 Adding a FireCell Wireless RIM to a Radio Loop Module
Wireless Remote Indicator Module
Battery Compartment
Radio Address Section
Remote Indicator Head Section
Log On Button & LED
Power Jumper
Ident Number
Remote Indicator LED
To add a device onto the Loop Module, take the device in front of the Radio Loop Module.
Step
Action
Screen
Display
No
1
With the Module in its normal state the screen will display:
2
Press the Rotary Control and the screen will now display:
3
Turn the Rotary Control until the screen displays:
DEV00 AL00 FT00
Device Status
Add New Device
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
4
4
Press the Rotary Control and the screen will now display:
Press Dev Log On
5
Press the devices log on button for 2 secs (confirmation led
will light on device) The screen will now display:
Add Dev xxxxx N ?
If the ident shown does not match the ident of the new device to be added then press
the rotary control when the above Add Dev xxxxx N? display is shown. This will return
the display to the previous menu.
6
Confirm the Dev ident number displayed is the same as
located on the device. If correct turn the Rotary Control until
the screen displays:
Add Dev xxxxx Y ?
7
Press the Rotary Control and the screen will now display:
Adding
8
Then the screen will display:
9
Turn the Rotary Control until the desired Address is shown;
10
Now select the address by pressing the rotary control. The
screen should now display;
11
Press the Back Button to return to the normal front screen
display.
New Address: 002
New Address: 007
01 Added I/O
DEV01 AL00 FT00
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
5
3.0 Adding a FireCell Wireless RIM to a Radio Hub
Wireless Remote Indicator Module
Battery Compartment
Radio Address Section
Remote Indicator Head Section
Log On Button & LED
Power Jumper
Ident Number
Remote Indicator LED
To add a device onto the Radio Hub, take the device in front of the Radio Hub.
Step
Action
Screen
Display
No
1
With the Radio Hub in its normal state the screen will display:
2
Press the Rotary Control and the screen will now display:
3
Turn the Rotary Control until the screen displays:
DEV00 AL00 FT00
Device Status
Add New Device
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
6
4
Press the Rotary Control and the screen will now display
available RCC’s for allocating the devices communication
path:
RCC01=00 Max 31
5
Turn the Rotary Control until the screen displays the required
RCC to programmed the device to:
RCC02=00 Max 31
6
Press the Rotary Control to select and the screen will now
display:
RCC02=00 Max 31
7
Press the Rotary Control and the screen will now display:
8
Turn the Rotary Control until the screen displays the required
Loop to be programmed and press the Rotary control to
select.
9
10
The display will now show the required address for the device
to be programmed. Turn the Rotary Control until the screen
displays the required address number to be programmed and
press the Rotary control to select.
Loop 1 Addr 001
Press Dev Log On
Loop 1 Addr 001
Press Dev Log On
Loop 1 Addr 001
Press Dev Log On
The display will now show:
Add By Log On
Press Dev Log On
11
Press the Rotary Control and the screen will now display:
Press Dev LogOn
12
Press the devices log on button for 2 secs (confirmation led
will light on device) The screen will now display:
Add Dev xxxxx N ?
If the ident shown does not match the ident of the new device to be added then press
the rotary control when the above Add Dev xxxxx N? display is shown. This will return
the display to the previous menu.
13
Confirm the Dev ident number displayed is the same as
located on the device. If correct turn the Rotary Control until
the screen displays:
Add Dev xxxxx Y ?
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
7
14
Press the Rotary Control and the screen will now confirm the
new devices loop and address number:
15
Press the back button until the screen displays:
16
Press the Rotary Control and the screen will now display:
17
Turn the Rotary Control until the screen displays:
18
Press the Rotary Control and the screen will now display:
Dev 000 of 001
19
When completed successfully the display will change to show:
Done 001 of 001
New Addr L1 A001
Un-assigned Dev
Device Status
Assign Device
Note: If unsuccessful when operation is carried out next to the Radio Hub. Re-try from
steps 16-19 with the device installed in its correct location.
20
Press the Back Button to return to the normal front screen
display.
DEV01 AL00 FT00
The adding of the Wireless Remote Indicator Module is now complete..
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
8
4.0 FireCell Configuration Tool programming
When programming the Wireless Remote Indicator Module onto a FireCell system via the
configuration tool the device should be added as an Input/Output unit.
All of the standard programming features for the device remain the same.
Details are explained below;
•
To add a Wireless Remote Indicator Module to the programme Click on the I/O
unit icon from the device palette as shown below:
•
The new device will be shown in the main window for devices allocated to an RCC.
An example is shown below:
•
Fill in the details for the specific device requirements.
below:
An example is shown
Devices Unique Ident Number
Loop Number the device is allocated to
Address Number allocated to the device
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
9
•
An example of the programming of an RCC with wireless remote indicators is
shown below:
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
10
5.0 Adding and Configuring a FireCell Wireless RIM to a
setup file
The Wireless Remote Indicator modules are added to the Loop Explorer configuration file
as Input/Output devices.
The selection of available FireCell devices are shown below with the Input/Output device
utilised for the remote indicator module highlighted.
•
Double click on the icon shown above to add the remote indicator module to the
setup. An example is shown below:-
•
Double click again on the Input/Output icon (remote indicator module) to expand
the device to show the input and output. An example is shown below:-
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
11
•
Double click on the Output 01 field. The display will change to show the output
properties for the device. Please ensure all fields are not selected and a delay is
not present.
•
Also ensure the Zone setting for the Output (Remote Indicator Module)
corresponds with the Zone which is to cause the device to operate. An example
with the correct settings and for Zone 1 operation is shown below:-
Note: The Zone setting for the output device (Wireless Remote Indicator Module) is only relevant
for the cause and effect when programming the unit to follow the activation of a Zone of devices.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
12
6.0 Cause & Effect - Linking a Zone of Devices to a RIM
•
An example is shown below for linking a Zone of devices to an individual Remote
Indicator Module. In this example Zone 1 is used.
Fire Alarm In
Remote Indicator Module Allocated to
Zone 1
Zone 1
Zone 2
Zone 2
Zone 3 etc
Zone 3 etc
•
Click on the cause and effect icon shown below.
•
Click on the Action icon shown below.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
13
•
The display will change to show available options for the input programming.
Click on the Fire Zone Inputs icon and the display will now show individual Zones.
Click on the individual Zone required and the OR/Single icon. An example below
shows the settings required for Zone 1.
•
Click on Next when completed.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
14
•
The display will change to show available options for the output programming.
Click on the Fire Zone Outputs icon and the display will now show individual
Zones. Click on the individual Zone required and the Continuous icon. An
example below shows the settings required for Zone 1.
•
Click on Next when completed.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
15
•
The display will change and allow a text description to be allocated for the Cause
and Effect rule written. An example is shown below.
•
Enter the required text to identify the rule and click on Finish when completed.
•
The rules for the system will be displayed under the Cause and effect icon on the
front display of the programme. They will be individually identifiable via the text
description allocated. An example is shown below.
•
Repeat the above programming for each of the Wireless remote indicator modules
on the system which are required to follow individual zone activations.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
16
7.0 Cause & Effect - Linking an Individual Device to a RIM
•
An example is shown below for linking an individual device to an individual
Remote Indicator Module. In this example detection device 4 is associated with
Remote Indicator Module device 6.
Fire Alarm In
Remote Indicator Module Allocated to
Device 1
Device 2
Device 3
Device 4
Device 5
Device 6
Device 6
•
Click on the cause and effect icon shown below.
•
Click on the Action icon shown below.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
17
•
The display will change to show available options for the input programming.
Click on the individual device required and the OR/Single icon. An example below
shows the settings required for device 4.
•
Click on Next when completed.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
18
•
The display will change to show available options for the output programming.
Click on the individual device required (RIM) and the Continuous icon. An
example below shows the settings required for remote indicator module device 6.
•
Click on Next when completed.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
19
•
The display will change and allow a text description to be allocated for the Cause
and Effect rule written. An example is shown below.
•
Enter the required text to identify the rule and click on Finish when completed.
•
The rules for the system will be displayed under the Cause and effect icon on the
front display of the programme. They will be individually identifiable via the text
description allocated. An example is shown below.
•
Repeat the above programming for each of the Wireless remote indicator modules
on the system which are required to follow individual device activations.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
20
8.0 Testing the RIM functionality
Following the programming of the Wireless Remote Indicator Module to the system and
completion of the control panels required cause and effect programming it is
recommended that the systems operation is fully tested to ensure correct operation.
Below are some testing recommendations to ensure correct functionality.
Cause and effect programmed for linking a Zone of devices to a Remote
Indicator Module.
•
Activate a device into a Fire Alarm condition in a zone which also has a RIM
allocated to that zone.
•
Ensure that the device operated into an alarm condition LED illuminates and also
the RIM which is allocated to that zone LED illuminates.
•
Silence the Control panel. The LED’s will still be illuminated.
•
Reset the fire alarm condition on the control panel. The devices LED which
operated into an alarm condition will extinguish and also the RIM LED which is
allocated to that zone will extinguish.
•
Repeat the above test for each device in the Zone. On each occasion the RIM’s
LED will operate and follow the operation as described above.
Note: The RIM LED will only illuminate for Fire Alarm activations in the allocated
Zone. The LED should not illuminate for any other activations.
Cause and effect programmed for linking an Individual device to a Remote
Indicator Module.
•
Activate a device into a Fire Alarm condition which also has a RIM allocated to
that device.
•
Ensure that the device operated into an alarm condition LED illuminates and also
the RIM which is allocated to that device LED illuminates.
•
Silence the Control panel. The LED’s will still be illuminated.
•
Reset the fire alarm condition on the control panel. The devices LED which
operated into an alarm condition will extinguish and also the RIM LED which is
allocated to that device will extinguish.
Note: The RIM LED will only illuminate for Fire Alarm activations from the allocated
device. The LED should not illuminate for any other activations.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
21
Dealer Information:
EMS Group Head Office
Technology House,
Sea Street
Herne Bay,
Kent CT6 8JZ
England
Tel: +44 (0) 8712 710804
Fax: +44 (0) 1227 369679
Email: [email protected]
The information contained within this literature is
correct at time of publishing. The EMS Group
reserves the right to change any information
regarding products as part of its continual
development enhancing new technology and
reliability. The EMS Group advises that any product
literature issue numbers are checked with its head
office prior to any formal specifications being
written.
EMS Group Head Office, Technology House, Sea Street, Herne Bay, Kent CT6 8JZ, England Tel: +44 (0) 1227
369570 Fax: +44 (0) 1227 369679 Email: [email protected] Website: www.emsgroup.co.uk
FireCell Remote Indicator Cause and Effect iss1.doc
TSD 115
22