OCTOBER, 2010
EC 97911-22
WINDOW PANNING AND TRIMS
1
GENERAL INFORMATION
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EXTERIOR PANNING
• Panning is primarily used to cover the perimeters of existing building openings prior to the installation of replacement
windows. The use of panning will often leave much of the existing building finishes undisturbed.
• Panning may also be used in new construction, particularly to achieve an historical look.
• Panning may be used with any fixed or operable Kawneer Sealair® Window Series. Panning is not recommended for
use with storefront or curtain wall systems.
• Standard panning profiles are available to accommodate most building conditions.
• Historic or custom panning profiles may supplied based on project specific requirements. Please contact your Kawneer
representative for detail assistance and associated costs.
• Panning is typically supplied factory fabricated to rough opening sizes. Extended panning legs are field trimmed to fit
building openings.
• Exterior panning must be securely attached to the building conditions prior to the window installation.
• Exterior panning legs are completely sealed to the building conditions on all perimeters.
• Exterior panning is weather-stripped and sealed prior to installation of the windows.
• Stainless steel retention clips are pre-attached to the exterior panning and hold the window in place until final
anchoring can be completed. Retention clips are not intended to permanently secure windows in place.
INTERIOR SNAP TRIM
• Standard interior snap trim profiles are available to accommodate most building conditions.
• Historic or custom snap trim profiles may be supplied based upon project specific requirements. Please contact your
Kawneer representative for detail assistance and associated costs.
• Interior snap trim is typically supplied in standard lengths and field cut to opening dimensions. Interior snap trim is
attached to the window face and building condition with 3” long clips.
• Interior snap trim may be used to securely anchor windows into building openings.
• Windows are securely anchored to the building condition with anchors installed through the window frame, strap anchors
or interior snap trim.
© Kawneer Company, Inc., 2010
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
• A combination of exterior panning and interior snap trim is normally required to completely cover existing building
conditions and finish the interior face of the window.
kawneer.com
WINDOW PANNING AND TRIMS
2
OCTOBER, 2010
TYPICAL INSTALLATION
EC 97911-22
INTERIOR TRIM
WINDOW DIM.
WINDOW DIM.
TOP OF WINDOW
1/4"
DAYLITE OPENING
DAYLITE OPENING
1/4"
3" LONG BASE CLIP @ 18"O.C.
(NOTE: FULL LENGTH CLIPS AVAILABLE)
CONTINUOUS SEAL
3" LONG BASE
CLIP @ 18" O.C.
BOTTOM OF WINDOW
TOP OF STOOL
INTERIOR
TRIM
INSTALLATION NOTE:
BACK BED WITH SEALANT
BEFORE INSTALLING
WINDOW. (TYP.)
WOOD BLOCKING
OR SHIM AS
REQUIRED
VARIES
MASONRY OPENING
MASONRY OPENING
VARIES
PERIMETER
SEAL
PERIMETER
SEAL
FIELD TRIM
AS REQUIRED
kawneer.com
© Kawneer Company, Inc., 2010
WOOD BLOCKING OR SHIM AS REQUIRED.
3/8" CLEARANCE REQUIRED FOR FASTENER.
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
FIELD TRIM
AS REQUIRED
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
TYPICAL PANNING AND TRIM INSTALLATION
INTO EXISTING WINDOW OPENING
© Kawneer Company, Inc., 2010
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
OCTOBER, 2010
CLIP FOR COPED AND
BUTT TYPE CORNER
JOINT AT SILL
kawneer.com
WINDOW PANNING AND TRIMS
EC 97911-22
WEATHERING
AT JAMBS AND HEAD
BACK SEAL CORNER
JOINT
BEAD OF SILICONE AT SILL
SPLINE SCREW FOR
COPED AND BUTT TYPE
CORNER JOINT AT SILL
3
ISOMETRIC
SPLINE SCREW FOR MITERED
CORNER JOINT AT HEAD
CLIP FOR MITERED
CORNER JOINT AT
HEAD
BACK SEAL CORNER
JOINT
WINDOW
RETENTION
CLIP
(106.4)
4-3/16"
1"
2-3/16"
(55.5)
WINDOW
DEPTH
246-240
PANNING
@ SILL
(50.8)
2-3/16"
(55.5)
2-3/16"
246-241 PANNING
@ HEAD and JAMBS
(55.5)
246-242 PANNING
@ HEAD and JAMBS
1"
(25.4)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1/4"
(6.4)
2"
TYPICAL PANNING DETAILS
246-240
PANNING
@ SILL
2-3/16"
(55.5)
kawneer.com
© Kawneer Company, Inc., 2010
(19.1)
WINDOW DIM.
1/4"
(6.4)
WINDOW PANNING AND TRIMS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
WINDOW DIM.
WINDOW DIM.
3/4"
(106.4)
(25.4)
4-3/16"
WINDOW DIM.
3"
(762)
4
OCTOBER, 2010
EC 97911-22
SCALE 6" = 1' 0" (19.1)
3/4"
WINDOW
DEPTH
(125.4)
4-15/16"
© Kawneer Company, Inc., 2010
kawneer.com
WINDOW DIM.
(66.7)
(73)
WINDOW
DEPTH
246-250 PANNING
@ SILL
WINDOW DIM.
2-5/8"
(125.4)
1/4"
(6.4)
1/4"
(6.4)
3-7/8"
(98.4)
(114.3)
4-1/2"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
WINDOW DIM.
2-7/8"
4-15/16"
WINDOW DIM.
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
OCTOBER, 2010
WINDOW PANNING AND TRIMS
EC 97911-22
246-251 PANNING
@ HEAD and JAMBS
2-7/8"
(73)
246-250 PANNING
@ SILL
4"
4"
(101.6)
(101.6)
5
TYPICAL PANNING DETAILS
SCALE 6" = 1' 0" 4"
(101.6)
(101.6)
4"
246-252 PANNING
@ HEAD and JAMBS
2-5/8"
(66.7)
WINDOW
DEPTH
4-15/16"
(125.4)
(95.3)
TYPICAL PANNING DETAILS
4"
246-253 PANNING
@ HEAD and JAMBS
2-7/8"
(73)
246-250 PANNING
@ SILL
4"
(101.6)
kawneer.com
© Kawneer Company, Inc., 2010
1/4"
(6.4)
(101.6)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
WINDOW DIM.
WINDOW PANNING AND TRIMS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
WINDOW DIM.
3-3/4"
6
OCTOBER, 2010
EC 97911-22
SCALE 6" = 1' 0" 2-5/8"
(66.7)
WINDOW
DEPTH
kawneer.com
(114.3)
4-1/2"
© Kawneer Company, Inc., 2010
WINDOW DIM.
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
WINDOW DIM.
1/4"
(6.4)
(111.1)
4-3/8"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
OCTOBER, 2010
WINDOW PANNING AND TRIMS
EC 97911-22
TYPICAL PANNING DETAILS
SCALE 6" = 1' 0" 5-5/16"
(134.9)
246-262 PANNING
@ HEAD and JAMBS
4-9/16"
(115.9)
4-13/16"
(122.2)
246-260 PANNING
@ SILL
5-5/16"
(134.9)
WINDOW
DEPTH
7
(114.3)
4-1/2"
TYPICAL PANNING DETAILS
4-13/16"
(122.2)
246-260 PANNING
@ SILL
5-5/16"
(134.9)
kawneer.com
© Kawneer Company, Inc., 2010
1/4"
(6.4)
246-261 PANNING
@ HEAD and JAMBS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
WINDOW DIM.
WINDOW PANNING AND TRIMS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
WINDOW DIM.
4-1/2"
(114.3)
8
OCTOBER, 2010
EC 97911-22
SCALE 6" = 1' 0" 5-5/16"
(134.9)
4-9/16"
(115.9)
WINDOW
DEPTH
kawneer.com
246-531
BASE
CLIP
2-1/2"
(63.5)
246-515
COVER
246-541
BASE
CLIP
5"
246-550
COVER
1"
246-526
BASE
CLIP
(25.4) 246-505
(25.4) 246-510
COVER
COVER
COVER
246-506
BASE
CLIP
1-3/4"
(44.4)
246-530
COVER
3"
(76.2)
246-540
COVER
246-551
BASE
CLIP
246-600
DRYWALL
ANCHOR CLIP
(50.8)
2"
(25.4) 246-500
246-521
BASE
CLIP
1-1/4"
(31.8)
(25.4)
(38.1)
(38.1)
1"
(50.8)
1-1/2"
2"
246-525
COVER
1-1/2"
246-501
BASE
CLIP
(25.4)
1-3/4"
(44.4)
WINDOW PANNING AND TRIMS
(12.7)
(127)
(25.4)
1"
EC 97911-22
1/2"
246-516
BASE
CLIP
1"
1-1/2"
(38.1)
028-808
#8 x 1/2" PH
(25.4)
1"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1"
(25.4)
1"
© Kawneer Company, Inc., 2010
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
OCTOBER, 2010
9
TYPICAL TRIM DETAILS
SCALE 6" = 1' 0" 1"
246-511
BASE
CLIP
2"
(50.8)
246-545
COVER
246-546
BASE
CLIP
3-1/2"
(88.9)
246-520
COVER
kawneer.com
© Kawneer Company, Inc., 2010
BLANK PAGE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
WINDOW PANNING AND TRIMS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
10
OCTOBER, 2010
EC 97911-22