CHAMCTERISTIC
MLSffgFM MqO
w/backer.products are manufactured with 7 plies of 10070 quality Radiata Pine veneers bonded together in a cross banded construction with phenolic resin.
Thepane|isconstrucledwiththe,lqcegrain.veneerpara||e|tothe|ongedgeoftheb6ard.Thepane|isover|aid
over|aidonthebackwithaFi|m120g/m2with'a.pheno1ic-res
Tulsa overlay panels provide an exceplional
agents, contractors can achieve as many as 10
-
1
5 re-uses.
17 o
53 4
Area
Section Modulus (z)
Pack size
Thickness of sheet
50 sheets
Dimensional tolerances
width
Length
Squareness
Straightness
Make up of product
No of olies
Type bf adhesive
Type of facing material
Anticioated number of reuses
Overlay material
'18 mm
+/- 0,4 mm
1,22mm
+01 - 1,6 mm
2,44 mm
+/- 1,3 mm per meter
+/-1,6 mm
radiata pine veneers
+01 - 1,6 mm
Second Moment ofArea
47 7, g
Parallel to the face grain
7,9
4,91
Perpendicular to lhe face gr
phenolic resin
Radiata Pine veneer
Parallel.to.theface,grain
Perpendicular to the fabe grain
10
MDO 323 face and
phenolic film back
Parallel to the face
37Q glm2
120 glm2
TULSAPANEL 18mm TPLY
Paralfel to the face
span
N/mm'
N/mm2
O,575 | kNm/m
grain | 12,2
12,
| kN/m
Load (Tonlm2)
Delleclcn Lmit
t89
11360
ol lhe
sgan
I
TULSAPANEL 18mm TPLY
TULSAPANEL 18mm TPLY
0r21
cf lhe
N/mm2
grain I S,a+ I kNm2/m
Perpendicularto the face grain
Defleclon Lm:t U360
I
103mm3
| 1o3mm4
Perpendicular to the face
Overlay material weight
MDO 323
Phenolic film
581 0
331 9
Parallel to the face grain
Perpendicular to the face grain
1
-
grain parallel to lhe span
€9
0r2ta
Load (Tor m2)
Deflecton
Lml L270 of lhe
span
IULSAPANEL 18mm TPLY
Load (Tonlm2)
grain perpendicular to the span
204
305
406
508
609
LorC {Tonln2)
HUMIDITY
During its manufacturing panel humidity is controlled and stabilized to 8% moisture content.
QUALIry CERTIFICATION
Testforphysica|andmechanica|propertiesarecaniedoutdai|ybyproductionandqua|itycontro|team
forexteriorglue(WBP) toensurethatall productsfulfill thestandardsandnormssetinPSl-95. TulsaalsoteststheirboardstocurrentEUnormsof EN636:2andEN13986:2,and
consistantly achieve a CE2+
Tulsa aware
allow their reuse, thud becoming friendly [o the enviroment.fi..
TECHNICAL PROPOSITIONS OF USE
It is important for TULSAF0RM MDO to be oiled twice before first use, and once thereafter before each successive pour.
r In work, store the panels on a flat and dry surface and under a roof or provisional cover, piling up them tidily on pieces of wood
of 50mm x 50mm or 50mm x 75mm intransverse
to the length.
rThe panel comes from factory with its edges painted. lf the board is cut and the wood exposed, this must be sealed with water resistant or rubberized paint, this will avoid any
damage caused by capillary penetration of humidity.
t Use lhe appropriate form remover (same as recommended, chemical reactive releases for non porous surfaces)
to prevent damage to the faces which might occur with metallic tools.
.Although TULSAFORM MDO 323 Overlay panels are very resistant to the abrasion and impact, as with any highly finished surface, care must be taken during cleaning and use to
prevent damage. Always use the appropriate vibrators and techniques to protect the panels surface.
TULSAFORM MDO 323 Film Overlay panels are produced using low polluting emission Phenolic resins in accordance European E-1 norms. The glue line fully meets the requirements
ofexterior bondino class 3 to BS EN 314 - 2: 1993