Replacement Parts List
Parts Diagram
Bowfishing Precautions
WARNING: Improper use of this reel can result in serious injury or death.
We recommend that you use a cable or slide system when attaching the line to the
arrow. The most hazardous snap-back can occur when fishing line is tied to the tail of
an arrow. Snap-back is a condition that can happen when, as the bowstring is
released, a trailing loop of line can tangle with the bowstring, cabling, arrow rest, or
other items which can result in serious injury or death. Minimize the amount of slack in
your line before shooting an arrow. Greater slack in the line increases chance of
snap-back of an arrow.
• ALWAYS press Thumb Button (#24) on reel to release the line pick-up pins
before shooting.
• ALWAYS check to see that line is not tangled.
• ALWAYS check line for cuts or wear. If the line breaks, you cannot control the
path of the arrow.
• ALWAYS wet line before firing first shot.
• ALWAYS wear eye protection.
• DO NOT aim at other people, and keep arrows away from children.
We strongly recommend that you take a bowfishing safety course before going bowfishing.
For more information, see:
Bowfishing Association of America: www.bowfishingassociation.com
National Bowhunter Education Program: www.nbef.org
National Bowhunter Education Foundation: www.bowhunter-ed.com
or your local archery shop with bowfishing expertise.
808 Bowfisher ™
Direct Mount
Owner’s Manual
Features
Zebco’s All-New 808 Bowfisher Direct Mount
• Zebco’s exclusive “Safe Shoot” color indicator
• Anti-Rotate bracket adapter for secure assembly
to most bows
• Integral Picatinny Weaver-style rail for easy
light/laser connection
• Tough stainless steel front cover
• Heavy duty machined brass gear
• Light weight durable EVA crank knob
• Silent continuous infinite anti-reverse
• Designed for heavy fishing situations
• Patents pending
Pre-Fishing Operation
Operation & Maintenance
Zebco Limited Warranty
FILLING THE SPOOL WITH LINE
REEL OPERATION
ZEBCO® LIMITED WARRANTY
Note: Always press and release the Thumb Button (#24) once prior to removing
the Front Cover Assembly (#2).
Remove the Front Cover Assembly (#2). Ensure all old line is removed from the reel.
Thread new line through the small opening in the nose of the Front Cover Assembly (#2).
Tie the new line around the Spool (#6), being careful not to leave a tag end greater than
¼ inch. Reinstall the Front Cover Assembly (#2), being careful not to pinch/capture any
loose line between the Front Cover Assembly (#2) threads. Lay spool of line on its side
or have an assistant hold the spool and start winding the line under finger tension. Stop
periodically to check if the line is twisting between the reel and the spool of line. If
twisting, rotate spool of line end for end. The correct amount of line should fill the Spool
(#6) to within 1/8” of the top of the spool’s lip.
Before shooting, make sure the line is tied to a slide or cable system and not tied to the
tail of the arrow, and ensure that knot is tight. Check to see that line inside reel spool is
not caught, twisted or tangled. Depress Thumb Button (#24) to release line, and
minimize the amount of slack in the line. After shooting, turn the crank handle to lock
spinnerhead and begin line/fish retrieval.
SETTING THE DRAG
Reels used infrequently should be cleaned and
relubricated annually, while reels used several
times a week should be cleaned and
relubricated monthly. The more frequent or
severe the use, the more often and thoroughly
a reel should be serviced. After use in
saltwater, the reel and spool should be rinsed
off with fresh water. If dropped in sand or dirt,
the reel should be cleaned and relubricated
entirely before using.
The drag system allows line to be pulled from the reel under tension without breaking
when a fish makes a quick run after being shot. To set the drag correctly, turn the drag
wheel (located on top of the reel) to the right to increase drag until there is a moderate
amount of drag tension when line is manually pulled from the reel. It’s better to start
fishing with your drag set too loose, than too tight. You can tighten the drag when the fish
is on, but if it is too tight, it could break the line. Always test and set the drag before
fishing, and loosen the drag after fishing (this should be done for each fishing trip).
LINE TWIST
This is usually caused by improperly installed line, or reeling in against a slipping drag.
To correct “line twist”, troll line behind boat or play it out in river current and rewind
under tension. Never reel in when you hear the drag slipping.
RECOMMENDED MAINTENANCE
Zebco Brands products are warranted for a period of one (1) year from date of
original retail purchase against defects in workmanship and/or materials. For
defective products, we encourage you to contact an authorized Zebco Brands
Warranty Center in your area. Should a service center not be located in your area,
please contact Customer Support for specific directions on how you can obtain
service and/or parts for your Zebco Brands product. Zebco will repair or replace
products at its option and return directly to purchaser.
This warranty does not cover Zebco products damaged due to abuse, misuse, normal
wear, excessive wear caused by neglect of cleaning and lubrication required or general
service requirements due to owner’s failure to provide reasonable and necessary
maintenance. Zebco products not covered by the Zebco Limited Warranty may be repaired
at a nominal charge to the purhaser, provided parts are available and the product is
returned with return postage prepaid.
“ALL INCIDENTAL AND/OR CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM
THIS WARRANTY INSERT. IMPLIED WARRANTIES ARE LIMITED TO THE LIFE OF
THE WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL
AND/OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY
VARY FROM STATE TO STATE.”
For more information concerning your Zebco product, please visit www.zebco.com
©2016 Zebco, a W.C. Bradley Co.
P.O. Box 270, Tulsa, OK 74101-0270
ZS4542
Customer Service: 1-800-588-9030