SEL ICON Dual Cube 19” Rack Mounting
Overview
NOTE: The ICON half-width Cube
requires a minimum vertical
separation of 1U (1.75 inches or 4.445
centimeters) above and below the
chassis for ventilation to meet
environmental specifications. The
Cube does not need any separation
for side spacing.
!
This guide will assist the customer with instructions for installing the SEL
Integrated Communications Optical Network (ICON®) half-width Cube
chassis (P/N SEL 8002-01) in the dual Cube 19" rack-mount option
(SEL P/N 915900330) configuration, depicted in Figure 1.
WARNING
Take precautions when removing or
installing screws near the backplane.
The #140-1815 screw is small enough
to fall behind the backplane shield.
i8183a
Figure 1 Dual Cube 19" Rack Mount With Optional SEL P/N 915900330
(Pictured Cable Side Out)
Installation
Table 1
Date Code 20141021
Required Parts (Not Supplied With SEL P/N 915900330)
Nomenclature
Part Number
Quantity
ICON Half-Width Cube
8002-01
2
Bracket Ear, 8000 Rack
190-3535
4
Screw #6-32-1/4"FH
140-1815
32
Rack Screw
Customer supplied
4
SEL ICON Dual Cube 19" Rack Mounting
2
Table 2
SEL P/N 915900330 Part List
Nomenclature
Part Number
Quantity
Bracket Mating, 8000 Rack
190-3538
1
Screw, Captive #6 x 3/8"
140-1814
6
Screw, Captive #6 x 3/8"
(140-1814)
Screw #6-32-1/4"FH
(140-1815)
Two ICON half-width Cube chassis can be mounted side by side in a standard
19" EIA relay rack by using the optional SEL 915900330 rack adapter kit and
following these instructions.
Step 1. If modules are already installed, note the module slot locations
and remove the modules.
Step 2. Orient the two chassis so the blue HMI side is facing away
from you and the cable access side is facing towards you.
Step 3. Designate one chassis as “Left” and the other “Right.”
Step 4. On the left ICON Cube chassis, remove the right #190-3535
bracket ear by removing the eight #140-1815 screws.
Step 5. On the right ICON Cube chassis, remove the left #190-3535
bracket ear by removing the eight #140-1815 screws.
Step 6. Rotate the left ICON Cube chassis 90° clockwise so the
chassis’ remaining bracket ear is facing up and the cable side is
facing you.
Step 7. Using the six #140-1814 screws found in the kit, thread each
screw through the holes depicted in Figure 2 until the screws
are fully threaded and in the “captive” state.
SEL ICON Dual Cube 19" Rack Mounting
Date Code 20141021
3
i8179a
Figure 2 Thread the Six #140-1814 Screws Into Their “Captive” State Into
the Holes Shown
Step 8. Rotate the right ICON Cube chassis 90° clockwise so the
chassis’ remaining bracket ear is facing down and the cable
side still faces you.
Step 9. Place the #190-3538 bracket mating plate on top of the right
ICON Cube chassis, ensuring that the side of the plate without
holes is farther away from you.
Step 10. Align the six holes on the plate with the holes on the right
ICON Cube chassis. See Figure 3 for proper bracket mating
plate alignment.
Date Code 20141021
SEL ICON Dual Cube 19" Rack Mounting
4
Figure 3 Align the Mating Plate to the Six Holes on Top of the Right Cube,
Ensuring the Back Is the Side With No Screw Holes
Step 11. Place the left ICON Cube chassis on top of the bracket mating
plate. Feed the six #140-1814 captive screws through the
bracket mating plate and loosely fasten each of the screws into
the right ICON Cube chassis.
Step 12. Once the left and right chassis are mechanically aligned,
tighten each of the six screws with 10–12 in-lbs of torque.
SEL ICON Dual Cube 19" Rack Mounting
Date Code 20141021
5
i8181a
Figure 4
Align the Left Cube to the Mating Plate on Top of the Right Cube
Step 13. You have the option of having either the HMI (blue side) or
cable access side towards the front of the rack. The ears of the
#190-3535 bracket ears must be facing the side you want to
have in front. If the bracket ears are not in front, reverse them
by removing the sixteen #140-1815 screws, rotating the bracket
ears 180°, and reattaching the screws with 10–12 in-lbs of
torque.
Date Code 20141021
SEL ICON Dual Cube 19" Rack Mounting
6
Step 14. Ensuring there is at least 1U of vertical clearance between the
Cube and the next device, proceed to mount the connected
cubes into your 19" rack with the customer-supplied rackmount bolts.
Step 15. Install the ICON modules into the ICON Cube chassis with
18 in-lbs of torque. If reinstalling, ensure they are going back
into the locations noted in Step 1.
Factory Assistance
We appreciate your interest in SEL products and services. If you have
questions or comments, please contact us at:
Schweitzer Engineering Laboratories, Inc.
2350 NE Hopkins Court
Pullman, WA 99163-5603 U.S.A.
Tel: +1.509.332.1890
Fax: +1.509.332.7990
Internet: www.selinc.com
Email: [email protected]
© 2014 by Schweitzer Engineering Laboratories, Inc. All rights reserved.
All brand or product names appearing in this document are the trademark or registered trademark of their respective holders. No SEL trademarks may be used without written permission. SEL products appearing in this document may be covered by
U.S. and Foreign patents.
2350 NE Hopkins Court • Pullman, WA 99163-5603 U.S.A.
Tel: +1.509.332.1890 • Fax: +1.509.332.7990
www.selinc.com • [email protected]
Schweitzer Engineering Laboratories, Inc. reserves all rights and benefits afforded
under federal and international copyright and patent laws in its products, including
without limitation software, firmware, and documentation.
The information in this document is provided for informational use only and is subject to change without notice. Schweitzer Engineering Laboratories, Inc. has
approved only the English language document.
This product is covered by the standard SEL 10-year warranty. For warranty details,
visit www.selinc.com or contact your customer service representative.
SEL ICON Dual Cube 19" Rack Mounting
*PLSICON-03*
Date Code 20141021