> INSTRUCTIONS MANUAL <
C O P E N H A G U E TA B L E
CPH90
B y R O N A N & E R WA N B O U R O U L L E C
HAY
> INTRODUCTION <
Copenhague is a furniture series designed by Ronan
and Erwan Bouroullec designed especially for the
University of Copenhagen in 2013. In addition to a ­h omely
and welcoming expression, functionality, durability
and ease of cleaning were important design requirements for
the university. The Bouroullec brothers approached the
task by merging design history with modern technology in an
idiom with a strong and independent appearance in
a broad and versatile series that embraces both public
and private environments.
> CARE AND MAINTENANCE <
CAUTION
With a little care you can prolong the life of your
LACQUERED OR STAINED WOOD
LINOLEUM
• Clean with a clean cloth wrung in water or in a solution
• Clean with a clean cloth wrung in water or in a solution
of water and a neutral detergent. Remove soap residue
of water and a neutral detergent or soap flakes. Remove
immediately using a clean, dry cloth.
soap residue immediately using a clean, dry cloth.
• If the surface is scratched or appears matt, use a
• If the surface is scratched or appears matt, use a care
• Use coasters under damp, hot or coloured objects to
care product suited especially for lacquered or stained
product suited especially for linoleum.
avoid permanent stains.
wood.
• Avoid covering the surface partially, for example with
• Avoid using detergents containing silicone, as that
(mineral spirit) or a damp nanosponge dipped in luke-
tablecloths or placemats, as colour variances may
would seal the stain in and make subsequent repairs
warm water or linoleum care. Follow up immediately
appear.
more difficult.
with a clean, dry cloth. Never use the nanosponge dry.
• Avoid using scouring cream or scouring pads, as they
• Avoid alkaline detergents such as soft (yellow) soap,
may scratch the surface.
washing soda, lye and scouring powder.
SOAPED WOOD
LAMINATE
• Clean with a clean cloth wrung in water or in a solution
• Clean with a clean cloth wrung in water or in a solution
of water and a neutral detergent or soap flakes. Remove
of water and a neutral detergent. Remove soap residue
soap residue immediately using a clean, dry cloth.
immediately using a clean, dry cloth.
• To remove stains, clean and scrub using a thick
• Stains may be carefully removed using household
solution of soap flakes that is not allowed to stay on the
ammonia or with a clean, damp cloth or a nanosponge
wood for more than 2 minutes. Then remove the
wrung in warm water. Never use the nanosponge dry.
remaining soap residue using a damp cloth.
Follow up immediately with a clean, dry cloth.
• If the grain of the wood rises after cleaning, gently
• Avoid using scouring cream or scouring pads, as they
sand down the wood using fine-grit sandpaper (No.
may scratch the surface.
• Tighten up the screws after one to two months’ use.
furniture and keep the materials in good condition.
Wood is a natural material, which may change in colour
• Avoid improper use such as putting your feet on the
and will patinate over time. Always remove stains quickly
table and standing on it.
before they can do any permanent damage to the
furniture.
> CARE AND MAINTENANCE <
• Avoid placing the table in direct sunlight or near a heat
source to reduce changes.
• When you move the furniture, make sure to lift it rather
• Stains may be carefully removed using white spirit
than pulling or pushing it to avoid damaging the floor,
legs and mountings.
220), always going with the grain.
• If the surface is scratched or appears matt, use a care
product suited especially for soaped wood.
> PA R TS <
1.
While assembling, keep the table inside the cardboard box with edge foam to protect the
tabletop from scratches etc. Make sure that all parts are included.
Ax7
Dx7
Bx4
Ex4
Fx2
Gx2
Cx4
Hx4
Allen key
2.
4.
Use 3 x D screws for perfect alignment. Make sure to place beam as shown.
Place 2 x E parts in the shown holes. Make sure that the E parts’ threads
are pointing upwards and the holes are facing each other.
Front
Front
3.
Now tighten the screws completely.
5.
6.
Place 1 x F and 1 x G in the shown holes. Make sure that the F parts’
Drop 2 x H parts in the shown holes and make sure to hit the F parts’ tapered holes.
tapered holes are pointing upwards.
Gently tighten both F parts little by little.
7.
Tighten both x H parts completely. Repeat step 4 to 7 at the other end of the table.
8.
9.
Use a proper screwdriver to fasten part D in the remaining free holes in the frame.
Flip the table (2 persons recommended).
13.
Havnen 1 8700 Horsens Denmark
+45 4282 0282 / [email protected]
HAY
ITEM NO. 70631 1
5 710441 206606