Safety Data Sheet
Alloy 910 3D Printing Filament
05/09/2016
Rev: 0
Emergency HOTLINE: 1-717-665-2421 Monday-Friday; 8:00 AM – 5:00 PM, EST
1. IDENTIFICATION
Product name: Alloy 910 3D Printer Filament
Synonyms: Polyamide copolymer, Nylon 6/69
Product Use: For use in 3D printing machines
Supplier: Fenner Drives 311 W Stiegel Street, Manheim, PA 17545
Emergency telephone numbers (24 hours a day): (717) 665-2421
2. HAZARDS IDENTIFICATION
Emergency Overview:
This product does not have health hazards if used as directed. During processing when
converted to the molten state, normal precautions of handling hot, sticky, fluid melts should
be observed
Potential Health Effects:
Eyes:
None
Skin:
None
Ingestion:
None
Inhalation:
None
Chronic Health Hazards: See section 11 for more information
Other Hazards: Dust may be generated from processing or other means that may become
combustible.
Classification: The classification and labeling information in this Safety Data Sheet should be
viewed as provisional, as the product’s ingredients and percentages are kept as a trade
secret / proprietary. This chemical does not meet the hazardous criteria set forth by the
2012 OSHA Hazard Communication Standard (29 CRF 1910.1200). However, this SDS
contains valuable information critical to the safe handling and proper use of this product.
This SDS should be retained and available for employees and other users of this product.
3. COMPOSITION / INFORMATION ON INGREDIENTS
Substance or Preparation: Substance
Chemical Name: Proprietary Cyclic Amide
Content: 0-10 wt%
Formula: Proprietary
CAS No: Proprietary
Fenner Drives, Manheim, PA 17545
Copyright 2016
by Fenner Drives. All Rights Reserved
This document is Engineering controlled. It is subject to change.
Contact Fenner Drives for latest revision
1 of 6
Safety Data Sheet
Alloy 910 3D Printing Filament
4. FIRST AID MEASURES
Inhalation: In case of gases evolving from melted filament, move subject to fresh air. Treat
symptomatically.
Skin Contact: Wash with water. In case of melted filament, wash affected skin area and
clothing with plenty of (soap and) water. Seek medical advice.
Eye Contact: In case of small particles, flush with plenty of water for at least 15 minutes.
Seek medical advice if any small particles still remain. In case of gases evolving from melted
filament of high temperature, flush with plenty of water for at least 15 minutes. Seek
medical advice if necessary.
Ingestion: Not a likely route of exposure
Most important symptoms and effects
Symptoms: Dermatitis may occur. May cause irritation to the mucous membranes and upper
respiratory tract.
5. FIRE-FIGHTING MEASURES
Extinguishing Media: Water, Foam, carbon dioxide, Dry chemical powder
Special Fire-Fighting Procedure: Self-contained breathing apparatus, MSHA/NIOSH
approved full protective gear.
Fire and Explosion Hazards: Product is not flammable or combustible
6. ACCIDENTAL RELEASE MEASURES
Methods for Cleaning up: Recovery if not contaminated or disposal
Personal Precautions: Strands/string remaining on ground may cause slipping. Wear
protective clothing as described in Section 8 of this SDS
Environmental Precautions: Do not allow material to contaminate ground water, soil,
ditches, and/or sewers. See Section 12 for additional Ecological Information.
7. HANDLING AND STORAGE
Handling: Taulman3D Nylons are thermoplastic resins. In the solid state, they are not
hazardous. During processing when converted to the molten state, normal precautions for
the handling of hot, sticky, fluid melts should be observed. Avoid breathing dust.
Storage: Keep containers tightly closed in a cool, dry, and well-ventilated area.
2 of 6
Safety Data Sheet
Alloy 910 3D Printing Filament
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Exposure Guidelines:
Occupational Exposure Limit Values:
Chemical Name
ACGIH TLV
Proprietary Cyclic
Amide
3
TWA: 5 mg/m inhalable
fraction and vapor
OSHA PEL
NIOSH IDLH
3
(Vacated) TWA: 1.5 mg/m dust
(Vacated) TWA: 5 ppm vapor
3
(Vacated) TWA: 20 mg/m vapor
3
(Vacated) STEL: 3 mg/m dust
(Vacated) STEL: 10 ppm vapor
3
(Vacated) STEL: 40 mg/m vapor
3
TWA: 1 mg/m dust
TWA: 0.22 ppm vapor
3
TWA: 1 mg/m vapor
3
STEL: 3 mg/m dust
STEL: 0.66 ppm vapor
3
STEL 3 mg/m vapor
Engineering Controls: Apply technical measures to comply with the occupational exposure
limits. Showers, eyewash stations, ventilation systems
Respiratory Protection: None required under normal use.
Eye Protection: Safety glasses with side shields
Skin Protection: Protective gloves required if in contact with molten material or newly
molded polymer parts. Protective clothing.
Work Hygienic Practices: Handle in accordance with good industrial hygiene and safety
practice
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: String/strand
Color: Amber transparent
Odor: no noticeable odor
Physical State: Solid
pH: Not determined
Melting Temperature: 193 °C
Decomposition Temperature: >290 °C
Solubility: Not determined
Specific Gravity: 1.11 (Air=1)
10. STABILITY AND REACTIVITY
Reactivity: Not reactive under normal conditions
Conditions to avoid: Temperatures above 290 °C may result in thermal decomposition
Reactivity with Water: No
Stability: Stable and non-reactive under normal handling and storage conditions
Hazardous Decomposition Products: Ammonia, hydrogen cyanide, carbon monoxide,
hydrocarbons
11. TOXICOLOGICAL INFORMATION
Principal Routes of Exposure: Eye contact, skin contact, inhalation, ingestion
Acute Toxicity: Lack of data
3 of 6
Safety Data Sheet
Alloy 910 3D Printing Filament
Local Effects: Dust may be irritating to eyes, skin, and respiratory system
Specific Effects: May cause skin irritation. Fumes may cause respiratory tract infection
Long Term Toxicity: None Found
Mutagenic Effects: None Found
Reproductive Toxicity: None Found
Carcinogenic Effects: None Found
Target Organ Effects: Lack of Data
Skin: Lack of data
Ingestion: Lack of data
Chemical Name
ATEmix (oral
ATEmix (dermal)
Inhalation LC50
Proprietary Cyclic
Amide
= 1210 mg/kg (rat)
= 1410 L/kg (rabbit
= 1438 mg/kg (rabbit(
= 8.16 mg/L (rat) 4 h
12. ECOLOGICAL INFORMATION
Ecotoxicity Effects: An environmental hazard cannot be excluded in the event of
unprofessional handling or disposal
Persistence and Degradability: Not determined
Bioaccumulation: Not determined
Mobility: Proprietary Cyclic Amide partition coefficient = -0.02
Component Information
Chemical Name
Algae/aquatic plants
Proprietary Cyclic
Amide
130: 72h desmodesmus subspicatus
mg/L EC50 160: 96h desmodesmus
subspicatus mg/L EC50 4320 –
4800: 72h pseudokirchneriella
subcapirara mg/L EC50
Fish
Crustacea
1400: 96h pimephales
promelas mg/L LC50
static 930: 96h lepomis
macrochirus mg/L LC50
static
500: 40h daphnia
magna straus mg/L
EC50 828-2920: 48h
daphnia magna mg/L
EC50
13. DISPOSAL CONSIDERATIONS
Waste Disposal Method: In accordance with local and federal regulations
14. TRANSPORT INFORMATION
Not regulated by the US Department of Transportation
15. REGULATORY INFORMATION
International Inventories
Chemical Name
TSCA
Proprietary Cyclic Amide
X
DSL/
NDSL
X
EINECS/
ELINCS
X
ENCS
Present
IECSC KECL
X
Present
PICCS AICS
X
X
4 of 6
Safety Data Sheet
Alloy 910 3D Printing Filament
US Federal Regulations
CERCLA
This material, as supplied, does not contain any substances regulated as hazardous
substances under the Comprehensive Environmental Response Compensation and Liability
Act (CERCLA) (40 CFR 302) or the Superfund Amendments and Reauthorization Act (SARA)
(40 CFR 355)
SARA 313
Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986
(SARA). This product does not contain any chemicals which are subject to the reporting
requirements of the Act and Title 40 of the Code of Federal Regulations, Part 372
CWA (Clean Water Act)
This product does not contain any substances regulated as pollutants pursuant to the Clean
Water Act (40 CFR 122.21 and 40 CFR 122.42)
US State Regulations
California Proposition 65
This product does not contain any Proposition 65 chemicals
US State Right-to-Know Regulations
Chemical Name
New Jersey
Proprietary Cyclic Amide
X
Massachusetts
X
Pennsylvania
X
16. OTHER INFORMATION
NFPA
Health Hazards Flammability
Instability
Special Hazards
Not determined Not determined Not determined Not determined
HMIS
Health Hazards Flammability
Instability
Special Hazards
Not determined Not determined Not determined Not determined
REVISION SUMMARY:
Date Prepared: May 9, 2016
Last Revised:
Previous Revision:
Summary of Revisions:
05/09/2016 - New SDS
Prepared by: Fenner Drives
The Information Herein Is Given In Good Faith, But No Warranty, Express Or Implied, Is
Made. Consult the Company for Further Information.
5 of 6
Safety Data Sheet
Alloy 910 3D Printing Filament
NOTICE REGARDING MEDICAL APPLICATION RESTRICTIONS: The company does not
recommend any of its products, including samples, for use: (A) in any application which is
intended for any internal contact with human body fluids or body tissues (B) as a critical
component in any medical device that supports or sustains human life; and (C) specifically
pregnant women or in any applications designed specifically to promote or interfere with
human reproduction.
6 of 6