I V O C L A R V I VA D E N T REMOVABLE More than dentures. SR Vivodent S ® Mid-line Denture Teeth Tooth mould chart SR Vivodent S SR Orthotyp S SR Ortholingual S PROCESSING INSTRUCTIONS Shades – 9 A–D shades (A1, A2, A3, A3.5, A4, B1, B2, B3, C2) – 2 Bleach shades (BL1, BL3) The most important principles of lingualized occlusion were taken into consideration for the design of the SR Ortholingual S. The centric contacts are concentrated in the mandibular fossae with the maxillary palatal cusps. The buccal cusps do not come into contact with each other. Shade selection The tooth shade is determined with the help of a shade guide according to the A–D shade system and the Ivoclar Vivadent Bleach shades. Shade selection with the patient should be carried out under defined light conditions (5,500K color temperature) during daylight (preferably light from the north). Lingualized occlusion One-to-one setup Anterior tooth selection If possible, the anterior teeth should be selected directly with the patient. The following reference points are determined with the help of a model analysis: a) Position of the central incisors in the maxilla The labial surface of the central incisors is aligned at a distance of 7 mm to the center of the incisive papilla. b) Position of the canines Identify the first large pair of rugae; the midpoint of the labial surface of the upper canines is aligned at a distance of 9 mm. The length of the dental arch measured across these three points can be used as a reference to select a set of anterior teeth with an appropriate width from the tooth mould chart. Occlusal concept The SR OrthotypTM S is the classic choice for use in complete, p artial and hybrid denture prosthetics. The Orthotyp teeth are set-up in accordance with a normal bite situation in a one-to-two relation. In this way, the primary contacts in the centric position are located in the central fossae in the mandible as well as on the marginal ridges. Conventional occlusion One-to-two setup The lingualized occlusal concept of the SR OrtholingualTM S is particularly suitable for implant prosthetics. Minimum layer thicknesses It must be ensured that the stability of the teeth and the correct shade effect are maintained. It is therefore recommended not to reduce teeth beyond the minimum layer thickness. • Anterior teeth: 2.5 mm • Posterior teeth: Central fossa min. 2.0 mm, cusp tips min. 2.5 mm, cervical area min. 2.5 mm. To ensure that removable dentures remain functional over longer periods of time, the following prerequisites should be met: – The dentures should be planned and fabricated in close cooperation with the dentist. – Dentist and dental technician should ensure a balanced occlusion and articulation. – All dental products should be used according to the instructions of the manufacturer. Denture teeth, in particular, should not be weakened by excess grinding. – In order to ensure a reliable bond with the denture base material, the teeth are cleaned with steam, roughened and wetted with monomer. When completing the dentures with an auto-curing polymer, also using mechanical retentions is recommended. – The application of a glaze varnish or denture cleaning spray is not recommended. – The teeth should not come into contact with a flame or direct heat. – Heat development as a result of too much pressure during grinding must be prevented. – We recommend wearing a face mask and using extraction equipment for protection against grinding dust. – Cleaning is performed with commercial cleaning agents. Contact with solvents must be prevented. –Do not use if the patient is known to be allergic to any componentof the product. SMALL SR Vivodent S 10.6 10.2 P3 Bold A13 Soft 8.4 8.0 42.6 9.7 A3 42.8 4.7 31.7 Orthotyp S SR TM NU3 29.8 NL3 9.6 8.6 32.3 Ortholingual S SR TM LU3 31.1 LL3 9.3 8.5 32.5 Dimensions in mm MEDIUM SR Vivodent S Bold 10.7 P6 10.7 A66 Soft 8.5 8.7 45.6 11.4 A26 44.5 8.8 A6 9.6 47.0 35.0 5.2 Orthotyp S SR TM 32.2 NL5 NU5 10.3 9.3 34.8 Ortholingual S SR TM LU5 32.6 LL5 9.9 9.0 34.3 Dimensions in mm LARGE SR Vivodent S Bold 11.8 P9 10.5 A27 Soft 9.1 9.0 48.7 12.0 P12 48.1 9.3 A8 10.5 50.2 38.4 5.6 Orthotyp S SR TM NL6 NU6 33.9 11.0 9.7 36.8 Ortholingual S SR TM 34.2 LL6 LU6 10.4 9.3 36.0 Dimensions in mm COMBINATION TABLE SR Vivodent® S SR Orthotyp S SR Ortholingual S (22°) (15°) TM TM Maxilla Mandible Semi-anatomical Lingualized Soft A13 A3 NU3 / NL3 LU3 / LL3 Bold P3 A3 NU3 / NL3 LU3 / LL3 Soft P6, A26 A6 NU5 / NL5 LU5 / LL5 Bold A66 A6 NU5 / NL5 LU5 / LL5 Soft P9 A8 NU6 / NL6 LU6 / LL6 Bold A27, P12 A8 NU6 / NL6 LU6 / LL6 Small Medium Large This Combination Table is recommended as a guideline. In special clinical situations, deviations may be possible. 100% CUSTOMER SATISFACTION GUARANTEED! ivoclarvivadent.com ©2014 Ivoclar Vivadent, Inc. Ivoclar Vivadent, SR Ortholingual, SR Orthotyp and SR Vivodent are registered trademarks of Ivoclar Vivadent 667082 Rev 1 1/2014 United States 175 Pineview Drive Amherst, New York 14228 716-691-0010 800-533-6825 Fax: 716-691-2285 www.ivoclarvivadent.com Canada 1 - 6600 Dixie Road Mississauga, Ontario L5T 2Y2 905-670-8499 800-263-8182 Fax: 905-670-3102 www.ivoclarvivadent.com
© Copyright 2024 Paperzz