NOVEMBER, 2006
WINDOW PANNING AND TRIMS
EC 97902-03
1
GENERAL INFORMATION
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EXTERIOR PANNING
• Panning is primarily used to cover the perimeters of existing building openings prior to the installation of replacement
windows. The use of panning will often leave much of the existing building finishes undisturbed.
• Panning may also be used in new construction, particularly to achieve an historical look.
• Panning may be used with any fixed or operable Kawneer Sealair® Window Series. Panning is not recommended for use
with storefront or curtain wall systems.
• Standard panning profiles are available to accommodate most building conditions.
• Historic or custom panning profiles may supplied based on project specific requirements. Please contact your Kawneer
representative for detail assistance and associated costs.
• Panning is typically supplied factory fabricated to rough opening sizes. Extended panning legs are field trimmed to fit
building openings.
• Exterior panning must be securely attached to the building conditions prior to the window installation.
• Exterior panning legs are completely sealed to the building conditions on all perimeters.
• Exterior panning is weather-stripped and sealed prior to installation of the windows.
• Stainless steel retention clips are pre-attached to the exterior panning and hold the window in place until final anchoring
can be completed. Retention clips are not intended to permanently secure windows in place.
• A combination of exterior panning and interior snap trim is normally required to completely cover existing building
conditions and finish the interior face of the window.
• Standard interior snap trim profiles are available to accommodate most building conditions.
• Historic or custom snap trim profiles may be supplied based upon project specific requirements. Please contact your
Kawneer representative for detail assistance and associated costs.
• Interior snap trim is typically supplied in standard lengths and field cut to opening dimensions. Interior snap trim is
attached to the window face and building condition with 3” long clips.
• Interior snap trim may be used to securely anchor windows into building openings.
• Windows are securely anchored to the building condition with anchors installed through the window frame, strap anchors
or interior snap trim.
© Kawneer Company, Inc., 2006
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
INTERIOR SNAP TRIM
www.kawneer.com
WINDOW PANNING AND TRIMS
NOVEMBER, 2006
TYPICAL INSTALLATION
EC 97902-03
INTERIOR TRIM
WINDOW DIM.
WINDOW DIM.
TOP OF WINDOW
1/4"
DAYLITE OPENING
DAYLITE OPENING
1/4"
3" LONG BASE CLIP @ 18"O.C.
(NOTE: FULL LENGTH CLIPS AVAILABLE)
3" LONG BASE
CLIP @ 18" O.C.
CONTINUOUS SEAL
BOTTOM OF WINDOW
TOP OF STOOL
INTERIOR
TRIM
WOOD BLOCKING
OR SHIM AS
REQUIRED
VARIES
MASONRY OPENING
VARIES
PERIMETER
SEAL
PERIMETER
SEAL
FIELD TRIM
AS REQUIRED
www.kawneer.com
INSTALLATION NOTE:
BACK BED WITH SEALANT
BEFORE INSTALLING
WINDOW. (TYP.)
© Kawneer Company, Inc., 2006
WOOD BLOCKING OR SHIM AS REQUIRED.
3/8" CLEARANCE REQUIRED FOR FASTENER.
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
FIELD TRIM
AS REQUIRED
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
TYPICAL PANNING AND TRIM INSTALLATION
INTO EXISTING WINDOW OPENING
MASONRY OPENING
2
© Kawneer Company, Inc., 2006
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
NOVEMBER, 2006
WINDOW PANNING AND TRIMS
EC 97902-03
WEATHERING
AT JAMBS AND HEAD
BACK SEAL CORNER
JOINT
BEAD OF SILICONE AT SILL
SPLINE SCREW FOR
COPED AND BUTT TYPE
CORNER JOINT AT SILL
CLIP FOR COPED AND BUTT
TYPE CORNER JOINT AT SILL
www.kawneer.com
3
ISOMETRIC
SPLINE SCREW FOR MITERED
CORNER JOINT AT HEAD
CLIP FOR MITERED
CORNER JOINT AT
HEAD
BACK SEAL CORNER
JOINT
WINDOW
RETENTION
CLIP
(106.4)
4-3/16"
1"
WINDOW
DEPTH
246-240
PANNING
@ SILL
2-3/16"
(55.5)
www.kawneer.com
2-3/16"
(55.5)
2-3/16"
246-241 PANNING
@ HEAD and JAMBS
(55.5)
246-242 PANNING
@ HEAD and JAMBS
(19.1)
3/4"
1"
(25.4)
246-240
PANNING
@ SILL
2-3/16"
(55.5)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1/4"
(6.4)
2"
(50.8)
TYPICAL PANNING DETAILS
© Kawneer Company, Inc., 2006
(19.1)
WINDOW DIM.
1/4"
(6.4)
WINDOW PANNING AND TRIMS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
WINDOW DIM.
WINDOW DIM.
3/4"
(106.4)
(25.4)
4-3/16"
WINDOW DIM.
3"
(762)
4
NOVEMBER, 2006
EC 97902-03
SCALE 6" = 1' 0"
WINDOW
DEPTH
(125.4)
4-15/16"
© Kawneer Company, Inc., 2006
WINDOW DIM.
(66.7)
(73)
WINDOW
DEPTH
WINDOW DIM.
2-5/8"
246-250 PANNING
@ SILL
www.kawneer.com
(125.4)
1/4"
(6.4)
1/4"
(6.4)
3-7/8"
(98.4)
(114.3)
4-1/2"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
WINDOW DIM.
2-7/8"
4-15/16"
WINDOW DIM.
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
NOVEMBER, 2006
WINDOW PANNING AND TRIMS
EC 97902-03
TYPICAL PANNING DETAILS
SCALE 6" = 1' 0"
4"
(101.6)
4"
(101.6)
246-251 PANNING
@ HEAD and JAMBS
246-252 PANNING
@ HEAD and JAMBS
2-5/8"
(66.7)
2-7/8"
(73)
WINDOW
DEPTH
246-250 PANNING
@ SILL
4"
4"
(101.6)
(101.6)
5
4-15/16"
(125.4)
(101.6)
246-253 PANNING
@ HEAD and JAMBS
2-5/8"
(66.7)
2-7/8"
(73)
246-250 PANNING
@ SILL
(101.6)
4"
www.kawneer.com
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1/4"
(6.4)
TYPICAL PANNING DETAILS
© Kawneer Company, Inc., 2006
WINDOW DIM.
WINDOW PANNING AND TRIMS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
WINDOW DIM.
3-3/4"
(95.3)
6
NOVEMBER, 2006
EC 97902-03
SCALE 6" = 1' 0"
4"
WINDOW
DEPTH
(114.3)
4-1/2"
© Kawneer Company, Inc., 2006
WINDOW DIM.
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
WINDOW DIM.
1/4"
(6.4)
(111.1)
4-3/8"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
NOVEMBER, 2006
WINDOW PANNING AND TRIMS
EC 97902-03
TYPICAL PANNING DETAILS
SCALE 6" = 1' 0"
5-5/16"
(134.9)
246-262 PANNING
@ HEAD and JAMBS
4-9/16"
(115.9)
4-13/16"
(122.2)
246-260 PANNING
@ SILL
5-5/16"
(134.9)
www.kawneer.com
WINDOW
DEPTH
7
(114.3)
4-1/2"
TYPICAL PANNING DETAILS
4-13/16"
(122.2)
246-260 PANNING
@ SILL
5-5/16"
(134.9)
www.kawneer.com
© Kawneer Company, Inc., 2006
1/4"
(6.4)
246-261 PANNING
@ HEAD and JAMBS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
WINDOW DIM.
WINDOW PANNING AND TRIMS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
WINDOW DIM.
4-1/2"
(114.3)
8
NOVEMBER, 2006
EC 97902-03
SCALE 6" = 1' 0"
5-5/16"
(134.9)
4-9/16"
(115.9)
WINDOW
DEPTH
9
WINDOW PANNING AND TRIMS
NOVEMBER, 2006
EC 97902-03
TYPICAL TRIM DETAILS
SCALE 6" = 1' 0"
1"
246-511
BASE
CLIP
2"
(50.8)
1-3/4"
(44.4)
246-545
COVER
246-530
COVER
246-525
COVER
2"
1-3/4"
(44.4)
246-531
BASE
CLIP
246-546
BASE
CLIP
3"
(76.2)
246-515
COVER
3-1/2"
(88.9)
246-520
COVER
1"
(25.4)
1"
246-541
BASE
CLIP
246-521
BASE
CLIP
5"
1-1/4"
(127)
(25.4)
1"
246-551
BASE
CLIP
246-600
DRYWALL
ANCHOR CLIP
www.kawneer.com
(12.7)
(31.8)
246-550
COVER
1/2"
246-516
BASE
CLIP
(25.4)
1"
246-540
COVER
(25.4)
(38.1)
(50.8)
1-1/2"
2-1/2"
(63.5)
© Kawneer Company, Inc., 2006
2"
246-506
BASE
CLIP
246-526
BASE
CLIP
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
1-1/2"
246-501
BASE
CLIP
(50.8)
COVER
(38.1)
(25.4) 246-510
COVER
(25.4)
(25.4) 246-505
COVER
1"
028-808
#8 x 1/2" PH
1"
(25.4) 246-500
1-1/2"
(38.1)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
WINDOW PANNING AND TRIMS
BLANK PAGE
www.kawneer.com
© Kawneer Company, Inc., 2006
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
10
NOVEMBER, 2006
EC 97902-03