EC centrifugal fans – RadiCal backward curved, Ø 250 Nominal voltage range Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A °C 1~ 200-240 50/60 1955 80 0,70 -25..+60 p. 164 / H3) B 1~ 200-240 50/60 2510 170 1,40 -25..+60 p. 164 / H3) C 1~ 200-240 50/60 1955 80 0,70 -25..+60 p. 165 / H4) D 1~ 200-240 50/60 2510 170 1,40 -25..+60 p. 165 / H4) Curve Nominal data Type Motor *3G 250 M3G 055-CF A *3G 250 M3G 055-DF *3G 250 M3G 055-CF *3G 250 M3G 055-DF (1) Nominal data in operating point with maximum load and 230 VAC 400 7 n rpm ηmax. = 2,4 Pa 500 2,0 600 3 I A LWA dB(A) 1 2050 70 0,60 69 A 2 1965 80 0,68 66 A 3 1955 80 0,70 61 A 4 1990 78 0,65 66 A 5 1325 22 0,23 60 A 6 1290 26 0,26 57 A 7 1290 26 0,28 53 A 8 1330 26 0,26 57 B 1 2680 145 1,15 76 B 2 2565 170 1,40 71 B 3 2510 170 1,40 67 B 4 2610 160 1,30 73 B 5 2330 96 0,80 72 B 6 2265 110 0,92 67 B 7 2250 115 0,96 64 B 8 2285 110 0,93 68 B 8 Ped W A 4 1,6 700 in H2O subject to alterations Curves: 2 Speed stages Technical features and electrical connection – Material: Housing: PA plastic 6, fibreglass-reinforced Impeller: PA plastic 6, fibreglass-reinforced Rotor: Thick layer passivated Electronics enclosure: Die-cast aluminium – Number of blades: 7 – Direction of rotation: Clockwise, seen on rotor – Type of protection: IP 54 – Insulation class: "B" – Mounting position: Any – Condensate discharges: None, open rotor – Mode of operation: Continuous operation (S1) – Bearings: Maintenance-free ball bearings 300 1,2 3 4 7 3 0,8 200 2 A 6 8 2 0,4 100 7 6 5 pfs 0 qV 100 200 200 300 400 400 600 1 500 800 600 1000 700 1200 1 5 800 1400 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 36 Mass of centrifugal fan Mass of centrifugal module with support basket – Technical features: See electrical connections p. 164 ff. – EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 – Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) – Cable exit: Variable – Protection class: I (if customer has provided connection for protective earth) – Product conforming to standards: EN 60335-1, CE – Approvals: VDE, UL, CSA, CCC, GOST are applied for kg R3G 250-RD17 -01 1,50 K3G 250-RD17 -01 2,28 R3G 250-RE07 -05 1,91 K3G 250-RE07 -05 2,69 R3G 250-RD17 -03 1,50 K3G 250-RD17 -03 2,28 R3G 250-RE07 -07 1,91 K3G 250-RE07 -07 2,69 600 3 n rpm ηmax. = 2,4 700 400 C I A LWA dB(A) C 1 2050 70 0,60 69 C 2 1965 80 0,68 66 C 3 1955 80 0,70 61 C 4 1990 78 0,65 66 D 1 2680 145 1,15 76 D 2 2565 170 1,40 71 D 3 2510 170 1,40 67 D 4 2610 160 1,30 73 4 3 0,8 200 1,2 3 300 Ped W 4 1,6 500 2,0 D 2 0,4 2 100 1 1 0 pfs Curves: Speed-controlled in H2O Centrifugal module w. support basket Pa kg Centrifugal fan qV 100 200 200 300 400 400 600 500 800 600 1000 700 1200 800 1400 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 38 ff. Inlet nozzle p. 158 Guard grille p. 160 Electr. connection p. 164 ff. 37 EC centrifugal fans – RadiCal backward curved, Ø 250, 2 speed stages, 85 W - electronics Ø4.5 (4x) R3G 250-RD17-01 (Centrifugal fan) Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4 (4x) 6 85 ±1 0 45 0+ 20 Ø255 Ø240 Ø164.5 Ø250 Ø172.5±0.2 Ø72 Ø27 Ø89 Ø80 2 Ø58±0.2 1.5 85 31 99±1 Connection line AWG 20, 4 x brass lead tips crimped 2 K3G 250-RD17-01 (Centrifugal module with support basket) 300 Ø5 (4x) o276±0.5 108.5 7 45° Ø3 Ø340±0 .5 85 ±1 0 38 45 0+ 6 20 Ø340±0 .5 22 Mounting dimensions: EC centrifugal fans – RadiCal backward curved, Ø 250, 2 speed stages, 170 W - electronics Ø4.5 (4x) R3G 250-RE07-05 (Centrifugal fan) Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm Depth of screw max. 10 mm M4(4x) M6(4x) 6 85 ±1 0 45 0+ 20 Ø255 Ø240 Ø164.5 Ø250 Ø172.5±0.2 Ø72 Ø101 Ø75 5 85 Ø58±0.2 1.5 99±1 31 Ø90±0.2 Connection line AWG 20, 4 x brass lead tips crimped 2 K3G 250-RE07-05 (Centrifugal module with support basket) 300 o276±0.5 108.5 7 Ø5 (4x) 45° Ø3 Ø340±0 .5 Mounting dimensions: 45 0+ 85 ±1 0 6 20 Ø340±0 .5 22 39 EC centrifugal fans – RadiCal backward curved, Ø 250, speed-controlled, 85 W - electronics Ø4.5 (4x) R3G 250-RD17-03 (Centrifugal fan) Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4 (4x) 6 85 ±1 0 45 0+ 20 Ø255 Ø240 Ø164.5 Ø250 Ø172.5±0.2 Ø72 Ø27 Ø89 Ø80 2 85 Ø58±0.2 1.5 99±1 31 2 Connection line AWG 20, 3 x brass lead tips crimped Control line AWG 22, 4 x brass lead tips crimped K3G 250-RD17-03 (Centrifugal module with support basket) 300 Ø5 (4x) o276±0.5 108.5 7 45° Ø3 Ø340±0 22 .5 85 ± 10 40 45 0+ 6 20 Ø340±0 .5 Mounting dimensions: EC centrifugal fans – RadiCal backward curved, Ø 250, speed-controlled, 170 W - electronics R3G 250-RE07-07 (Centrifugal fan) Ø4.5 (4x) Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm Depth of screw max. 10 mm M4(4x) M6(4x) 6 85 ±1 0 45 0+ 20 Ø255 Ø240 Ø164.5 Ø250 Ø172.5±0.2 Ø72 Ø101 Ø75 5 85 Ø58±0.2 1.5 99±1 31 2 Ø90±0.2 Control line AWG 22, 4 x brass lead tips crimped Connection line AWG 20, 3 x brass lead tips crimped K3G 250-RE07-07 (Centrifugal module with support basket) 300 o276±0.5 108.5 7 Ø5 (4x) 45° Ø3 Ø340±0 22 .5 45 85 ±1 0 6 0+ 20 Ø340±0 .5 Mounting dimensions: 41
© Copyright 2024 Paperzz