/G*
f
-ROG
PL LAIIX UABINI IND0NISIA
NlarlneAccommodation St'stem & Insulation Supplier
JENNY KIE
sALEs ExEtrurlvE
HP. : +62 857 77557777
Email : pt latex-marine@Yahoo co id
Bl ttYIElt
Blt-B Underlay
EIIEH=
+
D/\Et{Yt
P TEGH CO.,LTD.
Primary Deck Covering
Production description
BILLYTEX BX-B UNDERLAY is a deck composition product, which is composed of silica sand,
cemenl, Natural latex, SBR latex, etc. lt is 3 coating system, as a standard type, which can
be applied for the floor and deck in all ship types. lt also satisfies lM0 FTP code
MSC51(67) Annex 1, parts 2 and 6.
The final coating on the BILLYTEX BX-B UNDERLAY can be vinyl sheet, tile, polyurethane,
epoxy paint, etc.
Characteristics
Excellent adhesive component and elaslicity like natural rubber
No crack or no rust by water proolness
Long life material
Non-combustibility
Good chemical and abrasing resistances
lmpact absorption from collision
Special surface preparation is not required belore application
Application
Accommodation decks.
Floors in building
Top coat
Base coat
Primer coat
Steel deck or
Concrete
Certificates
ehssification
CE
(MED)
USCG
DNV
society
BV
LR
GL
ABS
KR
HK
RS
C
C
o
C
o
C
o
o
C
C
BILLYTEX
BX-B
UNDERLAY
x C : Approved,
-
:
Notapplicable
Installation Steps
Surface preparation:
BILLYTEX BX-B UNDERLAY may be applied
on hard foundations sueh as concrete and
steel, which should be free of dust, greasei
oil, dirt, etc.
Primer coat
:
BILLYTEX BX-PRIMER
It is
&
BX-1103
to carry
out, Base coat just
after finishing Primer coat work.
possible
Base,coat
:
& BX-1103
The compound should be completely
prior to the application of Top coat.
freezing temperature (Recommended curing
temperature is over +5C)
BILLYTEX BX-BASE will be cured after
approx. '16-24hours, at +18C and max. 50%
relative humidity, however, thg curing time
may be variable upon the thickness of the
applied layer, temperature, relative humidity
and the ventilation of the installed area.
The compound should be completely dry prior
to the
application of dense linish materials,
such as vinyl sheet, stud tile and carpet etc.
Content of moisture < 6%.
BILLYTEX BX-BASE
ToB coat
dry
the
:
BILLYTEX BX-TOP
&
Shelf -life
BX-1103
Polish the surface with #150-200 sand paper
after drying the surface. Double coating is
better than one coating t0 make good
su rface.
Mixing
Cleaning:
Use water for cleaning tools before
compound is cured.
:
1. Primer coat
BILLYTEX BX-PRIMER
BILLYTEX BX.L103
't0kg
3.3liter
2. Base coat
BILLYTEX BX-BASE
BILLYTEX BX-1103
200k9
l Sliter
3. Top coat
BILLYTEX BX-TOP
BILLYTEX BX.L103
1
0kg
3.3liter
Curing :
After application of BILLYTEX BX-BUNDERLAY,
the compound should be protected against
direct heat and sunlight as well as strong
wind. Also it should not be exposed under
:
The shelf-life
is max. twelve
months.
Caution
The BILLYTEX BX-PRIMER, BASE, T0P
powder should n0t be exposed to moisture
or freezing temperature.
:
For additional technical information,
please contact to our technical department.
Technical data
Basis
:
Color
:
Cement and synthetic latex
Density tg/cm3)
BX-PRIMER, BASE, TOP
Powder
Grey
BX-11 03
Liquid
White
Approx. 1.8 (applied)
:
Compressive strength (MPa)
41
Fire resistance
Fire resistant
:
Thickness (mm)
:
Stan dard
8
Minimum
4
Maximum
25
PRIMER
Curing time (hours)
BASE
16-24
TOP
2-4
Abration Resistance
x
Mean wear depth
Specification Achieved
Test Limits(mm)
Test Method
0.04
Speci al
0.05
BS 8204
According
to ambient conditions and humidity, curing time would be changed
Application method
Quantity(kg/mr)
P
rocess
Standard
Materials
6mm
7mm
8mm
9mm
10mm
Primer
BX-PRIMER
06
06
06
06
0d
coat
L-1 03
02
02
02
02
02
Base
BX-BASE
11.5
13.5
15.5
17.5
19.5
coat
L-1 03
1.05
1.23
1
.41
1.59
1.77
Top
BX-TOP
09
09
09
09
09
coat
L-1 03
03
03
03
03
03
thickness
0.5mm
7mm
0.5mm
N
ouantity may be changed depending on working condition.
Remark
ffi
ffim
ffi
x
x
I