MXB/MXG
(Motor valve)
HNB/G
Motor driven ball valve 2, 3 port valve
USB/G
For water, hot water, air, oil, corrosive fluid and steam
FAB/G
FGB/G
Overview
FVB
Water-hammering is eliminated with
CKD original ball opening/closing
FWB/G
structure.
This valve is suitable for water and
hot water control, oil and steam
FHB
FLB
application. Even with its small size,
the flow rate is large and the
AB
pressure loss is small.
The outstanding sealing properties
AG
and durability enable use in a variety
of applications.
AP/AD
APK/
ADK
Features
C O N T E N T S
Series variation
Safety precautions
Wiring diagram
A back-up O ring ensures a highquality seal.
No burn damage in motorlocked state
Standard type
2 port valve
3 port valve
Impedance and thermal protection
ensure that the motor does not burn
even if the ball locks.
Forward/reverse rotation
operation
(Except for the MHB/G4 series)
No limits to pressurizing
direction
(Except for 3-way valves)
Signal detection and manual
override are provided.
Class IPX3 "Rainproof"
actuator protection.
(
For standard and options T and K
only. Note that the MH GB 4 and
MHBP series are excluded.
)
A proportional control motor
valve is also available.
For
dry air
552
554
557
MXB1/MXB1F
MXG1
Explosion
proof
HVB/
HVL
SAB/
SVB
558
562
High corrosion resistance motor valve
2 port valve
MXB1-C
566
Oil-prohibited specification motor valve
2 port valve
MXB1-N/MXB1D-N
3 port valve
MXG1-N/MXG1D-N
582
586
Motor valve for steam
2 port valve
MSB1/MSB1F
590
Motor valve with relay
2 port valve
3 port valve
MXB1D/MXB1DF
MXG1D
570
574
NP/NAP/
NVP
CHB/G
MXB/G
Other G.P.
systems
PD/FAD/
PJ
High corrosion resistance motor valve with relay
2 port valve
MXB1D-C
578
Motor valve with relay for steam
2 port valve
MSB1D/MSB1DF
594
Proportional control motor valve
2 port valve
MXBC
3 port valve
MXGC
Motor valve type temperature control system MHBP
598
598
608
Miniature type
2 port valve
3 port valve
602
602
MHB4
MHG4
Electronic catalog file list
CVE/
CVSE
CPE/
CPD
Medical
analysis
Custom
order
Motor valve
Electric driven ball valve 2, 3 port valve
High-quality seal
612
Read the precautions in the introduction and
on page 554 carefully before starting use.
551
Electric driven ball valve 2, 3 port valve
Series
valve)
Motor valve(motor
variation
variation
Fluid
Port size (Upper: Nominal, Lower: port size)
HNB/G
Applications/purposes
Series
Bore shape
Water,
hot water
Air
Oil
10A
15A
20A
25A
32A
40A
50A
3/8
1/2
3/4
1
11/4
11/2
2
Steam
Page
USB/G
FAB/G
General control
Standard
type
Miniature type
558
MXB1
Standard bore
MXB1F
Full bore
558
MXG1
Standard bore
562
FWB/G
636
FHB
636
FLB
*1
MHB3
MHG3
Compact type
FGB/G
FVB
Reduced bore
AB
MHB4
602
MHG4
602
AG
AP/AD
For corrosive fluid
APK/
ADK
Full bore
570
For
dry air
MXG1D
Standard bore
574
Explosion
proof
High
corrosion
proof
MXB1-C
Reduced bore
566
HVB/
HVL
MXB1D-C
578
Oil-prohibited specifications
MXB1-N
582
MXG1-N
586
MXB1D
Standard bore
MXB1DF
*1
SAB/
SVB
NP/NAP/
NVP
CHB/G
MXB/G
Standard bore
For pure water and cleaning
For steam
MXB1D-N
582
Other G.P.
systems
MXG1D-N
586
PD/FAD/
PJ
590
CVE/
CVSE
MSB1
Standard bore
MSB1F
Full bore
590
MSB1D
Standard bore
594
MSB1DF
Full bore
*1
CPE/
CPD
Medical
analysis
For steam and hot water
Proportional control type
MXBC
MXGC
Accurate flow control
*1
594
*1
Standard bore
Custom
order
598
598
608
MHBP
Corresponding to service interruption
Self reset type
MHBR
Standard bore
636
Acid water/alkaline water control
For ionized water
MHG4-20X913
Reduced bore
823
*1: The model belongs to the standard bore, but this is a full bore structure.
*2: For details on differences by bore shape, refer to the orifice diameter and dimensions on each page.
552
553
Motor valve
Electric driven ball valve 2, 3 port valve
Parallel operation with other
valve is available
Valve open/closed at
ON/OFF contact
570
With relay
Safety precautions
Read this section carefully before starting use
(
Motor valve MXB1.MXB1F.MXG1.MXB1D.MXB1DF.MXG1D.MSB1.
MSB1F.MSB1D.MSB1DF.MHB4.MHG4.MHBP
Design & Selection
3
)
Wiring
(1) Connection is shown in the connection diagram on page 557
CAUTION
1
or is attached to the bonnet. Follow the connection diagram.
(2) When using the DC specifications, use a capacitance
Fluid viscosity
Generally, the valve can be used with a fluid viscosity of up
to
2
500mm2/s.
However, the properties may differ according to
power supply.
An all wave or half-wave rectified bridge will be affected
by ripples, so always use a stabilized power supply.
the fluid type, so consult with CKD.
(3) Avoid using a changeover switch with red and black lead
Fluid properties
wires as the signals could be input simultaneously.
(4) Parallel operation of motor valve (Excluding MXB1D,
Iron rust and dirt, etc., in the fluid can cause operation faults
or leaks.
MXB1DF, MXG1D, MSB1D, MSB1DF)
Installation, piping & wiring
Do not operate more than 1 motor valve in parallel with
the same contact. Operation faults will occur.
M
CAUTION
1
M
Installation
(1) Always hold the body when handling or installing the
product. Do not pull on the lead wires or drop the product.
(2) Install the valve within the range of the vertical state with
the motor section facing upward to the horizontal state.
(3) Avoid installment outdoors.
In parallel operation, insert a separate contact for each
motor valve.
M
M
(5) Parallel operation with other valves, etc. (excluding
MXB1D, MXB1DF, MXG1D, MSB1D, MSB1DF).
Do not operate in parallel with other products having different
resistance, such as a solenoid valve or contact protection
element, using the same contact. Operation faults will occur.
M
When operating in parallel, insert a contact between the
motor valve and solenoid valve, etc.
90˚
M
<For horizontal piping>
2
<For vertical piping>
Piping
(1) Fix the product when tightening or reinstalling the piping.
When piping to the body side, fix the body, and when
piping to the cap side, fix the cap.
(2) Fix and support the pipes so that the weight and vibration
of the pipes are not directly applied on the valves.
(3) The pressurizing direction, limited for the 3-way valve,
must be observed.
(4) When using heat insulating material, do not cover the
actuator section.
554
(6) When not using the signal detection wire, cut the exposed
core of the yellow and green wires, and insulate the wire ends.
(7) When using the signal detection wire with a large capacity
load or extremely small load, etc., use within the
specifications of the microswitch.
Series
MXB1/MXB1F.MXG1/MXB1D/MXB1DF/
MXG1D/MSB1/MSB1F/MSB1D/MSB1DF
MHB4/MHG4
MHBP
Maker name, type
OMRON SS-5
Matsushita Electric Works AH1680
OMRON SS-5GL
(8) When using in an area where the valve could be subject
to water drip, take measures to protect the lead
connection section.
(9) When wiring a terminal box with indicator light, do not pull
off the cover with force.
The crimp terminals inside could bend, or indicator
lighting faults or insulation faults could occur.
HNB/G
USB/G
FAB/G
FGB/G
FVB
When Using
Pan head machine screw
CAUTION
1
Open/close
indication hole
Failure to observe the cycle rate could lead to incorrect
operations or a shortened service life.
2
FHB
Intermediate bush
Cycle rate
FLB
Hexagon head bolt
Signal switchover
Switch the valve signal so that the next signal is input after
the valve operation ends.
If operation is stopped or if the signal is switched midway,
operation faults could occur and the service life could be
shortened.
AG
AP/AD
APK/
ADK
For
dry air
Manual operation methods
This applies to the MXB1, MXB1F, MXB1D, MXB1DF, MSB1,
MSB1F, MSB1D and MSB1DF. For the large bore size
(standard bore: Rc1 1/4 to Rc2, full bore: Rc1 to Rc1 1/2),
this applies to the manual override "M" type.
<Manual operation methods>
For the small bore size (standard bore: Rc3/8 to Rc1, full
bore: Rc1/2 to Rc3/4), insert a cross-recessed screwdriver,
etc., in the hole on the intermediate bush of the motor
valve, and slowly rotate it.
For the large bore size (standard bore: Rc1 1/4 to Rc2, full
bore: Rc1 to Rc11/2) manual override "M" type, insert a
cross-recessed screwdriver, etc., under the connection key
at the intermediate bush, and slowly rotate it.
Rotate for about 20 seconds between closed and open and
vice versa.
For both the large and small bore sizes, rotating in the
counterclockwise direction looking at the valve from above
will lead to "opening", and rotating in the clockwise direction
will lead to "closing".
<Precautions for manual operation>
Always turn the power OFF before starting.
Do not apply sudden force when rotating the crossrecessed screwdriver as the gears could be damaged.
For the large bore size (standard bore: Rc1 1/4 to Rc2, full
bore: Rc1 to Rc1 1/2) manual override "M" type, always
return the clutch after manual operation, and make sure
that the clutch is accurately connected before starting
operation.
Manual operations must be used only in emergencies.
AB
Explosion
proof
Maintenance
HVB/
HVL
WARNING
1
2
SAB/
SVB
Never remove the bonnet
NP/NAP/
NVP
Touching the electric parts inside could lead to electric
shocks.
CHB/G
Do not disassemble.
MXB/G
If a fault occurs, do not disassemble the product. Contact
your nearest dealer or CKD Sales Office.
Investigation of the cause is no longer possible if the product
is disassembled.
Other G.P.
systems
PD/FAD/
PJ
CVE/
CVSE
CPE/
CPD
Medical
analysis
Custom
order
Motor valve
Electric driven ball valve 2, 3 port valve
3
FWB/G
555
Safety precautions
Read this section carefully before starting use
Proportional control motor valve (MXBC, MXGC)
Design & Selection
5
Noise
When using outdoor piping, use resin piping to prevent damage
CAUTION
1
from lightning. A stepping motor is used, so noise will be
generated at the power line. Thus, use noise filters on devices
Power supply
susceptible to noise, such as computers connected to the common
Select the power supply allowing for a sufficient capacity.
(50W class is recommended.) Do not use a full wave rectified
bridge as it may be affected by the ripple or zero voltage, etc.
power supply.
6
Instead, use a safety power supply.
2
(1) Temperature control: When controlling the heating or cooling
temperature, attention must be paid to the balance of the
applied and lost heat. If this heat is not balanced, the control
Control methods
Use a controller or temperature regulator having a PID
will not stabilize, and vibration could occur causing a large
function, and keep the energizing frequency to 10% or less.
When using for ON/OFF control or control with a high
error. Design the device while taking the balance into
consideration so that the required fluid flow rate and
energizing frequency, the service life will be shortened, and the
temperature ( ) in respect to the target temperature are clear.
(2) Constant flow rate control: The resolution of the ball valve is 2.5%
or less. Thus, it may not be possible to attain the required flow rate
if more precise resolution is required. When using at high
pressures, note that this resolution limit may be particularly
apparent.
thermal protector could activate due to motor heating. This will
temporarily shut off the motor power and will prevent correct
operations. Lowering the energizing frequency will allow the
service life of the entire device to be lengthened, so carefully
consider the control methods and energizing frequency.
3
Service life
The product's service life will differ greatly according to the
operation. However, as a guide, the life is approx. 12 to 18
months when used with an energizing frequency of 10% for
eight hours a day.
4
7
Input signal and Cv flow factor
Installation, piping & wiring
WARNING
Ball valve open/close position
Fully closed position
Fully opened position
Fluid viscosity
The valve can be used with a fluid viscosity of up to
500mm2/s. However, the properties may differ according to
the fluid type, so consult with CKD.
<<Miscellaneous>> Refer to page 554 for the precautions
regarding the motor valve.
The ball valve opening degree position and input signal are
initially adjusted as follow.
Input signal
0mA
20mA
Actual control
1
Wiring
As shown below, the Cv flow factor variation amount in one
step will increase in the areas where the Cv flow factor is small
Refer to page 557.
and near large flow rates. Thus, avoid using in those ranges,
and obtain stability by controlling so that the expression
maximum Cv flow factor x 1/2 = required flow rate is satisfied.
<<Miscellaneous>> Refer to page 554 for the precautions
regarding the motor valve.
When Using
Flow rate characteristics
CAUTION
Cv flow factor
<<Miscellaneous>> Refer to page 554 for the precautions
regarding the motor valve.
Maintenance
0
(Fully closed)
Input current signal (mA)
20
(Fully opened)
The angle at which the ball valve starts to open and the Cv
flow factor in respect to the input signal will differ according to
the product.
556
WARNING
<<Miscellaneous>> Refer to page 554 for the precautions
regarding the motor valve.
HNB/G
USB/G
B
G
Motor valve wiring diagram (MX 1, MXB1F, MSB1, MSB1F)
Standard type
AC
Power
supply
Option: T (3-conductor cable)
FGB/G
White
DC power
Red
(1)
Open Green
(2)
Close
OLS
DC power
White
Yellow
(1)
Open
AC
Power
supply
Red
Option L
OLS
SLS
(2)
Close
Supply range
Black
FVB
Red
(1)
Open
AC
Power
supply
M
R
M
SLS
(2)
Close
Supply range
FHB
AG
(1): White - red After the A-C flow path operates, the microswitch (OLS) functions and stops the motor.
(2): White - black After the B-C flow path operates, the microswitch (SLS) functions and stops the motor.
Standard type
Option: T (3-conductor cable)
Black
AP/AD
APK/
ADK
Black
CR
CR
Explosion
proof
Black
OLS
M
Power SW White
supply
Green
Yellow
(A-C flow path)
Open light
For
dry air
Option: L, R (with light)
CR
SLS
OLS
Red
Power
supply SW
CR
CR
M
SLS
White
L
Red
Power
supply SW
OLS
HVB/
HVL
M
Option R
SAB/
SVB
SLS
White
Supply range
Supply range
Supply range
* L and R cannot be installed together.
(B-C flow path) Close light
2 port valve
Opening operation
Closing operation
3 port valve
A-C flow path
B-C flow path
MXB/G
Other G.P.
systems
SW:ON (Black-white,red) After the A-C flow path operates, the microswitch (OLS) functions and stops the motor.
SW:OFF (Black-white) After the B-C flow path operates, the microswitch (SLS) functions and stops the motor.
Proportional control motor valve wiring diagram (MX C)
PD/FAD/
PJ
Motor valve wiring diagram (MH 4)
B
G
MH GB4
MXGB C-N (Simple control type)
MX GBC (Standard type)
White
White
Power
supply
OLS
+
Red
(DC 0 to 20mA)
M
(1) Open
Power
supply
(2) Close
Red
M
Black
Supply range
+
Black
Yellow
Green
Detector resistance Brown
SLS
2 port valve
Opening operation 20mA
Closing operation 0 (4) mA
(1): Brown - green
(2): Brown - green
Detector resistance 2.4 to 3.2k
Detector resistance 0.1 to 0.9k
3 port valve
A-C flow path
B-C flow path
(1): Brown - green
(2): Brown - green
Detector resistance 2.4 to 3.2k
Detector resistance 0.1 to 0.9k
20mA
0 (4) mA
Potentiometer
Supply range
OLS
(1) Red
Open
Green
SLS
Close Black
(2)
Yellow
(A-C flow path)
Open light
Medical
analysis
M
Custom
order
Motor valve
Electric driven ball valve 2, 3 port valve
DC power supply 24 VDC
Supply range
(B-C flow path) Close light
2 port valve
Opening operation
Closing operation
3 port valve
A-C flow path
B-C flow path
CVE/
CVSE
CPE/
CPD
White
-
NP/NAP/
NVP
CHB/G
SW:ON (Black-white,red) After opening, the microswitch (OLS) functions and stops the motor.
SW:OFF (Black-white) After closing, the microswitch (SLS) functions and stops the motor.
B
G
-
FLB
AB
(1): White - red After opening, the microswitch (OLS) functions and stops the motor.
(2): White - black After closing, the microswitch (SLS) functions and stops the motor.
Motor valve with relay wiring diagram (MX GB 1D, MXB1DF, MSB1D, MSB1DF)
Red
FWB/G
Black
Supply range
* L and R cannot be installed together.
(B-C flow path) Close light
2 port valve
Opening operation
Closing operation
3 port valve
A-C flow path
B-C flow path
White
DC power
OLS
M
SLS
Black
(A-C flow path)
Open light
FAB/G
Option: L, R (with light)
(1): White - red
(2): White - black
(1): White - red
(2): White - black
[Cap side]
[Body side]
A
B
C
557
Electric driven ball valve 2 port valve
(motor valve)
MXB1/MXB1F Series
Port size: Rc3/8 to Rc2
Common specifications
MXB1 (standard bore)/MXB1F (full bore)
Descriptions
Water, hot water, air, oil (500mm2/s or less)
Working fluid
Working pressure range MPa
Withstanding pressure (water) MPa
Fluid temperature
Ambient temperature
%
Ambient humidity
Valve seat leakage cm3/min
Installation attitude
Pressurization direction
Protection grade
Electrical specifications
2.0
0 to 80 (no freezing)
-10 to 50
95 or less
0 (under 1.0MPa or 0.5MPa (only for port size Rc2) water pressure)
Limited from vertical to horizontal installation placing motor top.
Random
Rainproof IPX3 (standard and option T only)
MXB1-10
MXB1-15
MXB1F-15
MXB1-20
MXB1-25
MXB1F-20
MXB1-32
MXB1F-25
MXB1-40
MXB1F-32
MXB1-50
MXB1F-40
100 VAC (50/60Hz), 200 VAC (50/60Hz), 12 VDC and 24 VDC
Note 1
Starting Holding
Rated voltage
Apparent
power VA
0 to 1.0 (refer to working pressure range on individual specifications.)
100 VAC
200 VAC
100 VAC
200 VAC
Average Ampere 12 VDC
Note 2 24 VDC
A
Peak Ampere
12 VDC
A
Note 2 24 VDC
AC
Power consumption
12 VDC
24 VDC
W
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
1.1
1.5
0.7
1.0
1.8 or less
3 or less
1.2 or less
2 or less
7
15
13
18
17
24
MXB1 (standard bore) individual specifications
Descriptions
MXB1-10 Note 3
Rc3/8
Port size
10
Orifice
mm
10
Cv flow factor
Working pressure range MPa
AC
Interval when activated
sec. DC
AC
Cycle rate
Note 4
DC
1.2
Mass kg
Bronze body
1.2
Stainless steel body
MXB1-15
MXB1-20
MXB1-25
MXB1-32
MXB1-40
MXB1-50
Rc1/2
Rc3/4
Rc1
Rc11/4
Rc11/2
Rc2
10
15
20
25
32
40
6
16
29
50
98
125
0 to 1.0
0 to 0.5
13/11 (50/60Hz)
10/8 (50/60Hz)
8
10.5
2 cycles/min. or less
1 cycle/min. or less
1 cycle/2min. or less
1 cycle/min. or less
1.2
1.4
1.5
2.5
3.0
3.7
1.2
1.4
1.5
2.6
3.1
3.8
MXB1F (full bore) individual specifications
Descriptions
Port size
Orifice
mm
Cv flow factor
Working pressure range MPa
AC
Interval when activated
sec. DC
AC
Cycle rate
Note 4
DC
kg
Mass
MXB1F-15
MXB1F-20
MXB1F-25
MXB1F-32
MXB1F-40
Rc1/2
Rc3/4
Rc1
Rc11/4
Rc11/2
15
20
25
32
40
23
51
66
114
176
0 to 1.0
13/11 (50/60Hz)
8
10.5
2 cycles/min. or less
1 cycle/min. or less
1 cycle/min. or less
1.4
1.5
Note 1: Allowable voltage range should be within 10% of rated voltage.
Note 2: Each ampere is the value when rated voltage.
Note 3: MXB1-10 is full bore.
Note 4: Cycle rate should be within the specifications.
Note 5: Consult with CKD about other than above specifications.
558
0 to 0.5
10/8 (50/60Hz)
1 cycle/2min. or less
2.5
3.0
3.7
MXB1/MXB1F Series
How to order
HNB/G
MXB1
32
0
T M
1
USB/G
MXB1F
FAB/G
Series
Series
Symbol
A
A Port size
B
B Body/Seat
C
C Other options
*1
*2
D
D Manual override
*3
E
E Voltage
FGB/G
MXB1
MXB1F
(Standard bore) (Full bore)
Descriptions
FVB
Port size
10
Rc3/8 *4
15
Rc1/2
20
Rc3/4
25
Rc1
32
Rc11/4
40
Rc11/2
50
Rc2
FWB/G
FHB
FLB
AB
Body/Seat
0
Body - bronze/Seat - PTFE
H
Body - bronze/Seat - reinforced PTFE
E
Body - stainless steel/Seat - PTFE
W
Body - stainless steel/Seat - reinforced PTFE
Other options
Descriptions
Applications
AG
AP/AD
APK/
ADK
For
dry air
Remarks
Blank
5-conductor cable 0.5 mm2
(output lead wire)
T
3-conductor cable 0.75 mm2
(no output)
B
Round terminal box Optional lead wire
(5-conductor)
length required
SAB/
SVB
L
Round terminal box + light Fully open confir.
Lighting at fully open
(ON when open, 3 terminal) by light
NP/NAP/
NVP
R
Round terminal box + light
Fully open confir. by light
Lighting at fully closed
(OFF when closed, 3 terminal) Fully closed confir.
CHB/G
Explosion
proof
3-conductor cabtire
Output lead
wire not required cord used
HVB/
HVL
MXB/G
Manual override
Blank
Blank
M
Manual override
Voltage
1
2
3
4
Other G.P.
systems
PD/FAD/
PJ
100 VAC (50/60Hz)
200 VAC (50/60Hz)
24 VDC
12 VDC
CVE/
CVSE
CPE/
CPD
*1: When selecting both no output (T in "C") and a round terminal box (B in "C") as options,
designate "C" as TB. A 3-terminal round terminal box will be provided.
*2: Combinations of LR, TL, TR, BL and BR aren't available for "C".
*3: When manual override ("D" M) is used, port size 32, 40, or 50 is selected for MXB1.
For MXB1F, port size 25, 32, or 40 is selected.
When port size is 10 to 25, manual override is equipped as standard.
*4: For full-bore port size 10, the model is MXB1.
Medical
analysis
Motor valve
Electric driven ball valve 2 port valve
Custom
order
<Example of model number>
MXB1F-32-0TM-1
Series: MXB1F (full bore)
A Port size
B Body-seat
C Other options
D Manual override
E Voltage
: Rc1 1/4
: Body - bronze/Seat - PTFE
: 3 conductor cable (no output)
: Selected
: 100VAC (50/60Hz)
559
MXB1/MXB1F Series
Internal structure and main parts material
MXB1/MXB1F
1
2
18
3
4
5
6
7
13
8
14
9
15
19
10
20
17
16
11
12
No. Parts name
Material
1
2
3
4
5
6
7
8
9
10
Bonnet
ADC12
Aluminum alloy die-casting
Geared motor
-
-
Cam
PA
Polyamide
Gasket
NBR
Nitrile rubber
Micro switch
-
-
Adaptor
ZDC2
Zinc alloy die-casting
O ring
NBR
Nitrile rubber
Intermediate bush SUS303
Stainless steel
Shaft
SUS303 (SUS304)
Stainless steel (stainless steel)
Ball seat
PTFE
Tetrafluoroethylene resin
( ) shows values for stainless steel body
560
No. Parts name
Material
11
12
13
14
15
16
17
18
19
20
Valve ball
C3771 (SUS304)
Brass *2 (stainless steel)
Body
CAC407 (SCS13)
Bronze casting (stainless steel casting)
P plate assembly PF
Phenol resin
O ring *1
FKM/NBR
Fluoro rubber/nitrile rubber
O ring
FKM
Fluoro rubber
Cap
CAC407 (SCS13) Bronze casting (stainless steel casting)
Hexagon head bolt SWCH
Carbon steel wire for cold forging
Cross headed pan SWCH
Carbon steel wire for cold forging
Bushing
PF
Phenol resin
Cabtire cord
0.5mm2, 5-conductor
-
*1: Upper O ring is NBR, lower is FKM. For stainless steel, FKM is used for
both upper and lower O rings.
*2: Valve ball is made of hard chrome plated brass.
MXB1/MXB1F Series
(Page 612)
Dimensions
MXB1-10/15/20/25-*
MXB1F-15/20-*
55
MXB1-32/40/50-*
MXB1F-25/32/40-*
(42)
40
HNB/G
(50)
80
54
64
63
USB/G
FAB/G
FGB/G
300
300
D
C
D
C
FVB
FWB/G
FHB
FLB
AB
2-E
A
Cabtire cord length 300mm
Model
MXB1-10-*
MXB1-15-*
MXB1-20-*
MXB1-25-*
MXB1F-15-*
MXB1F-20-*
AG
B
A
2-E
B
AP/AD
Cabtire cord length 300mm
Model
A
B
C
D
E
50 (56)
24 (28)
124.5
139.5 (140.5)
Rc3/8
56
28
124.5
139.5 (140.5)
Rc1/2
65
34
130.5
150 (151)
Rc3/4
76
41
133.5
156.5 (157.5)
Rc1
65
28
130.5
150
Rc1/2
71
34
133.5
156.5
Rc3/4
MXB1-32-*
MXB1-40-*
MXB1-50-*
MXB1F-25-*
MXB1F-32-*
MXB1F-40-*
A
B
C
D
E
84
50
166
193.5 (195.5)
Rc11/4
94
57
172
205.5 (207.5)
Rc11/2
108
70
181
220.5 (221.5)
Rc2
84
41
166
193.5
Rc1
95
50
172
205.5
Rc11/4
107
57
181
220.5
Rc11/2
(Page 612)
Optional dimensions
Round terminal box
MXB1/MXB1F- Port size -* B
For
dry air
Explosion
proof
Note 1: For manual override "M", the MSB1 Series yoke is inserted between
the valve and actuator, making dimensions C and D 22 mm longer.
Note 2: ( ) shows values for stainless steel body
Note 1: ( ) shows values for stainless steel body
APK/
ADK
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
CHB/G
Round terminal box with indicator light
MXB1/MXB1F- Port size -* L
R
(G)
MXB/G
(G)
Other G.P.
systems
PD/FAD/
PJ
Port size
MXB1F
10
15
20
25
32
40
50
15
20
25
32
40
F
G
H
74
96
58.5
74
96
58.5
74
96
64.5
74
96
67.5
82
104
77.5 (Note 1)
82
104
83.5 (Note 1)
82
104
92.5 (Note 1)
Port size
MXB1
MXB1F
10
15
20
25
32
40
50
15
20
25
32
40
F
G
H
74
101
58.5
74
101
58.5
74
101
64.5
74
101
67.5
82
109
77.5 (Note 1)
82
109
83.5 (Note 1)
82
109
92.5 (Note 1)
Custom
order
Motor valve
Electric driven ball valve 2 port valve
(F)
(F)
MXB1
Medical
analysis
H
G1/2
H
G1/2
CPE/
CPD
46
46
CVE/
CVSE
Note 1: For manual override "M", the MSB1 Series yoke is inserted between the valve and actuator, making dimensions 22 mm longer.
561
Electric driven ball valve 3 port valve
(motor valve)
MXG1 Series
MXG1 Series
Port size: Rc1/2 to Rc2
Common specifications
MXG1
Water, hot water, air, oil (500mm2/s or less)
0 to 1.0 (refer to working pressure range on individual specifications.)
2.0
0 to 80 (no freezing)
-10 to 50
95 or less
0 (under 1.0MPa or 0.5MPa (only for port size Rc2) water pressure)
Limited from vertical to horizontal installation placing motor top.
Limited to Port C pressurized.
Rainproof IPX3 (standard and option T , K only)
MXG1-15
Individual specifications
Descriptions
MXG1-15
Port size
Orifice
mm
Cv flow factor
Working pressure range MPa
AC
Interval when
DC
activated sec.
AC
Cycle rate
Note 3
DC
Mass
kg Bronze body
Stainless steel body
MXG1-20
MXG1-32
MXG1-40
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
1.1
1.5
0.7
1.0
1.8 or less
3 or less
1.2 or less
2 or less
7
15
13
18
17
24
MXG1-50
MXG1-20
MXG1-25
MXG1-32
MXG1-40
MXG1-50
Rc1/2
Rc3/4
Rc1
Rc11/4
Rc11/2
Rc2
10
14
19
23
30
38
3
6
11
16
28
0 to 1.0
47
0 to 0.5
20/16 (50/60Hz)
26/22 (50/60Hz)
16
21
1 cycle/min. or less
1 cycle/2min. or less
1 cycle/2min. or less
1 cycle/5min. or less
1.3
1.4
1.7
2.7
3.2
4.1
1.3
1.4
1.7
2.8
3.3
4.2
Note 1: Allowable voltage range should be within 10% of rated voltage.
Note 2: Each ampere is the value when rated voltage.
Note 3: Cycle rate should be within the specifications.
Note 4: Consult with CKD about other than above specifications.
562
MXG1-25
100 VAC (50/60Hz), 200 VAC (50/60Hz), 12 VDC and 24 VDC
Starting Holding
Descriptions
Working fluid
Working pressure range MPa
Withstanding pressure (water) MPa
Fluid temperature
Ambient temperature
Ambient humidity
%
Valve seat leakage cm3/min
Installation attitude
Pressurization direction
Protection grade
Electrical specifications
Rated voltage Note 1
Apparent
100 VAC
power
VA
200 VAC
100 VAC
200 VAC
Average Ampere A 12 VDC
Note 2 24 VDC
Peak Ampere
12 VDC
Note 2 24 VDC
Power consumption W AC
12 VDC
24 VDC
MXG1 Series
How to order
HNB/G
MXG1
20
0
K
2
USB/G
FAB/G
FGB/G
Series
Symbol
A Port size
Rc1/2
15
Rc3/4
20
Rc1
25
Rc11/4
32
40
Rc11/2
50
Rc2
A Port size
B
B Body/Seat
C
C Other options
*1
*2
D
D Voltage
Descriptions
FVB
FWB/G
FHB
FLB
AB
Body/Seat
Body - bronze/Seat - PTFE
0
Body - bronze/Seat - reinforced PTFE
H
Body - stainless steel/Seat - PTFE
E
Body - stainless steel/Seat - reinforced PTFE
W
Other options
Descriptions
Blank 5-conductor 0.5 mm2(output lead wire)
T
3-conductor 0.75 mm2(no output)
B
Round terminal box (5 cores)
L
Round terminal box + light
(ON at A-C flow path, 3-terminal)
R
Round terminal box + light
(ON at B-C flow path, 3-terminal)
Multi fluids 90˚ turn switching
K
type
Operation time 1/2
Voltage
1
2
3
4
AG
AP/AD
APK/
ADK
Applications
Remarks
Output lead wire not required 3-conductor cabtire cord used
Optional lead wire length required
A-C flow path complete Lighting at operation complete
confirmation by light
of Flow path A-C
B-C flow path complete Lighting at operation complete
confirmation by light
of Flow path B-C
To avoid pump load Both flows mixed
during switching
For
dry air
Explosion
proof
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
CHB/G
100 VAC (50/60Hz)
200 VAC (50/60Hz)
24 VDC
12 VDC
MXB/G
Other G.P.
systems
*1: When optional specifications of "C" is duplicate, select one from following combinations.
A 3 terminal round terminal box is provided for TB, TK, BK, LK, RK, TBK or TB.
*2: Combinations of LR, TL, TR, BL and BR aren't available for "C".
PD/FAD/
PJ
CVE/
CVSE
CPE/
CPD
Medical
analysis
<Example of model number>
MXG1-20-0K-2
Custom
order
A Port size
B Body-seat
C Other options
D Voltage
Motor valve
Electric driven ball valve 3 port valve
Series: MXG1
: Rc3/4
: Body - bronze/Seat - PTFE
: Multi fluids type (90 degree rotation switching method, operation time 1/2)
: 200 VAC (50/60Hz)
563
MXG1 Series
Internal structure and main parts material
MXG1
1
2
3
18
4
5
6
7
13
8
14
9
15
19
10
20
17
16
11
12
A
B
C
No. Parts name
Material
1
2
3
4
5
6
7
8
9
10
Bonnet
ADC12
Aluminum alloy die-casting
Geared motor
-
-
Cam
PA
Polyamide
Gasket
NBR
Nitrile rubber
Micro switch
-
-
Adaptor
ZDC2
Zinc alloy die-casting
O ring
NBR
Nitrile rubber
Intermediate bush SUS303
Shaft
SUS303 (SUS304) Stainless steel (stainless steel)
Ball seat
PTFE
( ) shows values for stainless steel body
564
Stainless steel
Tetrafluoroethylene resin
No. Parts name
Material
11
12
13
14
15
16
17
18
19
20
Valve ball
C3771 (SUS304) Brass *2 (stainless steel)
Body
CAC407 (SCS13) Bronze casting (stainless steel casting)
P plate assembly PF
Phenol resin
O ring *1
FKM/NBR
Fluoro rubber/nitrile rubber
O ring
FKM
Fluoro rubber
Cap
CAC407 (SCS13) Bronze casting (stainless steel casting)
Hexagon head bolt SWCH
Carbon steel wire for cold forging
Cross headed pan SWCH
Carbon steel wire for cold forging
Bushing
PF
Phenol resin
Cabtire cord
0.5mm2, 5-conductor
-
*1: Upper O ring is NBR, lower is FKM.For stainless steel,
FKM is used for both upper and lower O rings.
*2: Valve ball made of hard chrome plated brass.
MXG1 Series
Dimensions
(Page 612)
MXG1-15/20/25-*
55
MXG1-32/40/50-*
(42)
40
63
(50)
54
64
HNB/G
80
USB/G
FAB/G
300
FVB
D
D
C
C
FGB/G
300
FWB/G
FHB
A
A
B
B
FLB
AB
3-E
AC
3-E
A C
B
Cabtire cord length 300mm
B
AG
Cabtire cord length 300mm
Model
A
B
C
D
E
MXG1-15-*
MXG1-20-*
MXG1-25-*
56
28
124.5
154.5
Rc1/2
65
34
130.5
166.5
Rc3/4
76
41
133.5
175.5
Rc1
AP/AD
Model
A
B
C
D
E
MXG1-32-*
MXG1-40-*
MXG1-50-*
84
50
166
213
Rc11/4
94
57
172
225
Rc11/2
108
70
181
242
Rc2
APK/
ADK
For
dry air
Explosion
proof
(Page 612)
Optional dimensions
Round terminal box
MXG1- Port size -* B
Round terminal box with indicator light
MXG1- Port size -* L
R
(G)
HVB/
HVL
SAB/
SVB
(G)
NP/NAP/
NVP
CHB/G
MXB/G
H
H
46
46
Other G.P.
systems
G1/2
PD/FAD/
PJ
G1/2
CVE/
CVSE
(F)
F
G
15
20
25
32
40
50
74
CPE/
CPD
(F)
H
Port size
F
G
H
96
58.5
74
101
58.5
74
96
64.5
74
101
64.5
74
96
67.5
74
101
67.5
82
104
77.5
82
109
77.5
82
104
83.5
82
109
83.5
82
104
92.5
15
20
25
32
40
50
82
109
92.5
Medical
analysis
Custom
order
Motor valve
Electric driven ball valve 3 port valve
Port size
565
High corrosion proof electric driven ball valve 2 port valve
(motor valve)
MXB1-C Series
MXB1-C Series
Port size: Rc1/2 to Rc2
Working fluid: Corrosive fluid
Common specifications
MXB1-C
Corrosive fluid (not to corrode materials)
0 to 1.0 (refer to working pressure range on individual specifications.)
2.0
0 to 80 (no freezing)
-10 to 50
95 or less
0 (under 1.0MPa or 0.5MPa (only for port size Rc2) water pressure)
Limited from vertical to horizontal installation placing motor top.
Random
Rainproof IPX3 (standard and option T only)
MXB1-15-C
Individual specifications
Descriptions
MXB1-15-C
Port size
Orifice
mm
Cv flow factor
Working pressure range MPa
AC
Interval when
activated
sec. DC
AC
Cycle rate
Note 3 DC
kg
Mass
MXB1-20-C
MXB1-32-C
MXB1-40-C
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
1.1
1.5
0.7
1.0
1.8 or less
3 or less
1.2 or less
2 or less
7
15
13
18
17
24
MXB1-50-C
MXB1-20-C
MXB1-25-C
MXB1-32-C
MXB1-40-C
MXB1-50-C
Rc1/2
Rc3/4
Rc1
Rc11/4
Rc11/2
Rc2
9.2
12.5
16
20
24.5
32
4.8
9
15.5
24
37
0 to 1.0
13/11 (50/60Hz)
8
10.5
2 cycles/min. or less
1 cycle/min. or less
1 cycle/min. or less
1.1
1.2
62
0 to 0.5
10/8 (50/60Hz)
Note 1: Allowable voltage range should be within 10% of rated voltage.
Note 2: Each ampere is the value when rated voltage.
Note 3: Cycle rate should be within the specifications.
Note 4: Consult with CKD about other than above specifications.
566
MXB1-25-C
100 VAC (50/60Hz), 200 VAC (50/60Hz), 12 VDC and 24 VDC
Starting Holding
Descriptions
Working fluid
Working pressure range MPa
Withstanding pressure (water) MPa
Fluid temperature
Ambient temperature
Ambient humidity
%
Valve seat leakage cm3/min
Installation attitude
Pressurization direction
Protection grade
Electrical specifications
Rated voltage Note 1
100 VAC
Apparent
power
VA 200 VAC
100 VAC
200 VAC
Average Ampere A 12 VDC
Note 2 24 VDC
Peak Ampere A 12 VDC
Note 2 24 VDC
AC
Power consumption W
12 VDC
24 VDC
1 cycle/2min. or less
1.4
2.3
2.4
2.8
MXB1-C Series
How to order
HNB/G
MXB1
32
C T M
1
USB/G
FAB/G
FGB/G
Series
Symbol
A
A Port size
B
B Body/Seat
C Other options
*1
*2
D Manual override
*3
E Voltage
Descriptions
FVB
Port size
15
Rc1/2
20
Rc3/4
25
Rc1
32
Rc11/4
40
Rc11/2
50
Rc2
FWB/G
FHB
FLB
AB
Body/Seat
C
Body - stainless steel/Seat- PTFE
Other options
Descriptions
Applications
Remarks
Blank 5-conductor 0.5mm2 (output lead wire)
2
T
3-conductor 0.75mm (no output) Output lead wire not required 3-conductor cabtire cord used
B
Round terminal box (5 cores) Optional lead wire length required
L
Round terminal box + light (on at open) Fully open confir. by light Lighting at fully open
R
Round terminal box + light (on at closed) Fully closed confir. by light Lighting at fully closed
C
D Manual override
Blank Blank
M
Manual override
E
AP/AD
APK/
ADK
For
dry air
Explosion
proof
HVB/
HVL
SAB/
SVB
Voltage
1
100 VAC (50/60Hz)
2
200 VAC (50/60Hz)
3
24 VDC
4
12 VDC
NP/NAP/
NVP
CHB/G
*1: When selecting both no output ("C" T) and a round terminal box ("C" B) as options,
designate "C" as TB. A 3-terminal round terminal box will be provided.
*2: Combinations of LR, TL, TR, BL and BR aren't available for "C".
*3: Manual override ("D" is M) is available for port size 32, 40 and 50.
When port size is 15 to 25, manual override is equipped as standard.
<Example of model number>
MXB1-32-CTM-1
MXB/G
Other G.P.
systems
PD/FAD/
PJ
CVE/
CVSE
Series: MXB1-C
CPE/
CPD
: Rc1 1/4
: Body - stainless steel/Seat - PTFE
: 3 conductor cable (no output)
: Selected
: 100VAC (50/60Hz)
Medical
analysis
Custom
order
High corrosion proof motor valve
Electric driven ball valve 2 port valve
A Port size
B Body/Seat
C Other options
D Manual override
E Voltage
AG
567
MXB1-C Series
Internal structure and main parts material
MXB1-*-C
1
2
18
3
4
5
13
6
14
7
15
8
9
16
19
10
20
17
11
12
No. Parts name
Material
1
2
3
4
5
6
7
8
9
10
Bonnet
ADC12
Aluminum alloy die-casting
Geared motor
-
-
Cam
PA
Polyamide
Gasket
NBR
Nitrile rubber
Micro switch
-
-
Adaptor
ZDC2
Zinc alloy die-casting
O ring
NBR
Nitrile rubber
568
Intermediate bush SUS303
Stainless steel
Shaft
SUS316
Stainless steel
Ball seat
PTFE
Tetrafluoroethylene resin
No. Parts name
Material
11
12
13
14
15
16
17
18
19
20
Valve ball
SUS316
Stainless steel
Body
SCS14
Stainless steel die casting
P plate assembly PF
Phenol resin
O ring
NBR
Nitrile rubber
O ring
FKM
Fluoro rubber
Insert
SUS316
Stainless steel
Hexagon head bolt SWCH
Carbon steel wire for cold forging
Cross headed pan SWCH
Carbon steel wire for cold forging
Bushing
PF
Phenol resin
Cabtire cord
0.5mm2, 5-conductor
-
MXB1-C Series
(Page 612)
Dimensions
MXB1-15/20/25-C
55
MXB1-32/40/50-C
(42)
40
64
63
54
80
(50)
HNB/G
USB/G
FAB/G
C
FGB/G
300
300
D
D
C
FVB
FWB/G
B
FHB
FLB
2-E
A
2-E
A
AB
B
AG
Cabtire cord length 300mm
Model
MXB1-15-C
MXB1-20-C
MXB1-25-C
Cabtire cord length 300mm
A
B
C
D
E
56.5
59
25
119
131.5
Rc1/2
32
121.5
137.5
Rc3/4
71
38
125.5
144.5
Rc1
AP/AD
Model
A
B
C
MXB1-32-C
MXB1-40-C
MXB1-50-C
78
49
83
53
100
65
D
E
155.5
180
Rc11/4
161
187.5
Rc11/2
166.5
199
Rc2
Note 1: For manual override "M", the MSB1 Series yoke is inserted between the
valve and actuator, making dimensions C and D 22 mm longer.
APK/
ADK
For
dry air
Explosion
proof
HVB/
HVL
Optional dimensions
Round terminal box
MXB1- Port size -C B
SAB/
SVB
Round terminal box with indicator light
MXB1- Port size -C L
R
(G)
NP/NAP/
NVP
(G)
CHB/G
MXB/G
Other G.P.
systems
46
H
H
46
PD/FAD/
PJ
CPE/
CPD
G1/2
G1/2
CVE/
CVSE
Medical
analysis
(F)
(F)
F
G
H
Port size
F
G
H
15
20
25
32
40
50
74
96
53
74
101
53
74
96
55.5
74
101
55.5
74
96
59.5
74
101
59.5
82
104
67 (Note 1)
82
109
67 (Note 1)
82
104
72.5 (Note 1)
82
109
72.5 (Note 1)
82
104
78 (Note 1)
15
20
25
32
40
50
82
109
78 (Note 1)
High corrosion proof motor valve
Electric driven ball valve 2 port valve
Port size
Custom
order
Note 1: For manual override "M", the MSB1 Series yoke is inserted between the valve and actuator, making dimensions 22 mm longer.
569
driven ball valve 2 port valve with relay
MXB1D/MXB1DFElectric
Series
(motor
valve)
MXB1D/MXB1DF Series
Port size: Rc3/8 to Rc2
Common specifications
MXB1D (standard bore) / MXB1DF (full bore)
Descriptions
Water, hot water, air, oil (500mm2/s or less)
Working fluid
Working pressure range MPa
Withstanding pressure (water) MPa
Fluid temperature
Ambient temperature
%
Ambient humidity
Valve seat leakage cm3/min
Installation attitude
Pressurization direction
Protection grade
Electrical specifications
2.0
0 to 80 (no freezing)
-10 to 50
95 or less
0 (under 1.0MPa or 0.5MPa (for MXB1D-50/40) water pressure)
Limited from vertical to horizontal installation placing motor top.
Random
Rainproof IPX3 (standard and option T only)
MXB1D-10 MXB1D-15
MXB1DF-15
MXB1D-20 MXB1D-25 MXB1D-32 MXB1D-40 MXB1D-50
MXB1DF-25 MXB1DF-32 MXB1DF-40
MXB1DF-20
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
Note 1
Starting Holding
Rated voltage
Apparent
power
VA
0 to 1.0 (refer to working pressure range on individual specifications.)
100 VAC
200 VAC
100 VAC
200 VAC
Power consumption W
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
8
16
MXB1D (standard bore) individual specifications
Descriptions
MXB1D-10
Rc3/8
Port size
10
Orifice
mm
10
Cv flow factor
Working pressure range MPa
Interval when
50Hz
activated sec. 60Hz
Note 3
Cycle rate
1.2
Mass kg Bronze body
1.2
Stainless steel body
Note 2
MXB1D-15
MXB1D-20
MXB1D-25
MXB1D-32
MXB1D-40
MXB1D-50
Rc1/2
Rc3/4
Rc1
Rc11/4
Rc11/2
Rc2
10
15
20
25
32
40
6
16
29
50
98
125
0 to 1.0
0 to 0.5
13
10
8
11
2 cycles/min. or less
1 cycle/min. or less
1.3
1.4
1.6
2.6
3.0
3.8
1.3
1.4
1.6
2.7
3.1
3.9
MXB1DF (full bore) individual specifications
Descriptions
MXB1DF-15 MXB1DF-20 MXB1DF-25 MXB1DF-32 MXB1DF-40
Rc11/2
Rc1/2
Rc3/4
Rc1
Rc11/4
Port size
32
40
15
20
25
Orifice
mm
114
176
23
51
66
Cv flow factor
0 to 1.0
0 to 0.5
Working pressure range MPa
10
Interval when
13
50Hz
8
activated sec. 60Hz
11
2 cycles/min. or less
Note 3
Cycle rate
1 cycle/min. or less
kg
3.0
3.8
1.4
1.6
2.6
Mass
Note 1: Allowable voltage range should be within 10% of rated voltage.
Note 2: MXB1D-10 is a full bore.
Note 3: Cycle rate should be within the specifications.
Note 4: Consult with CKD about other than above specifications.
570
MXB1D/MXB1DF Series
How to order
HNB/G
MXB1D
32
0
T M
1
USB/G
MXB1DF
FAB/G
Series
Series
Symbol
FVB
Port size
10
Rc3/8
15
Rc1/2
20
Rc3/4
25
Rc1
32
Rc11/4
40
Rc11/2
50
Rc2
A
A Port size
FGB/G
MXB1D MXB1DF
(Standard bore) (Full bore)
Descriptions
*4
FWB/G
FHB
FLB
AB
Body/Seat
0
Body - bronze/Seat - PTFE
H
Body - bronze/Seat - reinforced PTFE
E
Body - stainless steel/Seat - PTFE
W
Body - stainless steel/Seat - reinforced PTFE
B
B Body/Seat
Other options
Descriptions
C
C Other options
*1
*2
Blank
T
B
L
R
Applications
AG
AP/AD
APK/
ADK
For
dry air
Remarks
5-conductor cable 0.5 mm2
(output lead wire)
Explosion
proof
3-conductor cable 0.75 mm2 Output lead
3-conductor cabtire
wire not required cord used
(no output)
HVB/
HVL
Round terminal box Optional lead
(5 conductor)
wire length required
Round terminal box + light Fully open confir.
Lighting at fully open
(ON when open, 3 terminal) by light
SAB/
SVB
NP/NAP/
NVP
Round terminal box + light
Fully open confir. by light
Lighting at fully closed
(OFF when closed, 3 terminal) Fully closed confir.
CHB/G
MXB/G
Manual override
Blank
Blank
M
Manual override
D
D Manual override
*3
E
E Voltage
Other G.P.
systems
PD/FAD/
PJ
Voltage
1
100 VAC (50/60Hz)
2
200 VAC (50/60Hz)
CVE/
CVSE
<Example of model number>
MXB1DF-32-0TM-1
Series: MXB1DF (full bore)
A Port size
B Body/Seat
C Other options
D Manual override
E Voltage
CPE/
CPD
Medical
analysis
Custom
order
Motor valve with relay
Electric driven ball valve 3 port valve
*1. When selecting both no output ("C" T) and a round terminal box ("C" B) as options,
designate "C" as TB. A 3-terminal round terminal box will be provided.
*2: Combinations of LR, TL, TR, BL and BR aren't available for "C".
*3: When manual override ("D" M) is used, port size 32, 40, or 50 is selected for MXB1D.
For MXB1DF, 25, 32, or 40 is selected.
When port size is 10 to 25, manual override is equipped as standard.
*4: For full-bore port size 10, the model is MXB1D.
: Rc1 1/4
: Body - bronze/Seat - reinforced PTFE
: 3 conductor cable (no output)
: Selected
: 100VAC (50/60Hz)
571
MXB1D/MXB1DF Series
Dimensions
MXB1D-10/15/20/25-*
MXB1DF-15/20-*
55
MXB1D-32/40/50-*
MXB1DF-25/32/40-*
(42)
40
54
64
63
HNB/G
(50)
80
USB/G
FAB/G
FGB/G
300
300
D
C
D
C
FVB
FWB/G
FHB
FLB
AB
2-E
B
A
A
2-E
B
AG
APK/
ADK
AP/AD
Cabtire cord length 300mm
Model
MXB1D-10-*
MXB1D-15-*
MXB1D-20-*
MXB1D-25-*
MXB1DF-15-*
MXB1DF-20-*
Cabtire cord length 300mm
Model
A
B
C
D
E
50 (56)
24 (28)
124.5
139.5 (140.5)
Rc3/8
56
28
124.5
139.5 (140.5)
Rc1/2
65
34
130.5
150 (151)
Rc3/4
76
41
133.5
156.5 (157.5)
Rc1
65
28
130.5
150
Rc1/2
71
34
133.5
156.5
Rc3/4
MXB1D-32-*
MXB1D-40-*
MXB1D-50-*
MXB1DF-25-*
MXB1DF-32-*
MXB1DF-40-*
A
B
C
D
E
84
50
166
193.5 (195.5)
Rc11/4
94
57
172
205.5 (207.5)
Rc11/2
108
70
181
220.5 (221.5)
Rc2
84
41
166
193.5
Rc1
95
50
172
205.5
Rc11/4
220.5
Rc11/2
107
57
181
Explosion
proof
Note 1: For manual override "M", the MSB1 Series yoke is inserted between the
valve and actuator, making dimensions C and D 22 mm longer.
Note 2: ( ) shows values for stainless steel body
Note 1: ( ) shows values for stainless steel body
For
dry air
Optional dimensions
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
CHB/G
Round terminal box
MXB1D/MXB1DF- Port size -* B
Round terminal box with indicator light
MXB1D/MXB1DF- Port size -* L
R
(G)
MXB/G
(G)
Other G.P.
systems
PD/FAD/
PJ
CVE/
CVSE
Port size
10
15
20
25
32
40
50
15
20
25
32
40
F
G
H
74
96
58.5
74
96
58.5
74
96
64.5
74
96
67.5
82
104
77.5 (Note 1)
82
104
83.5 (Note 1)
82
104
92.5 (Note 1)
Port size
MXB1D MXB1DF
10
15
20
25
32
40
50
15
20
25
32
40
F
G
H
74
101
58.5
74
101
58.5
74
101
64.5
74
101
67.5
82
109
77.5 (Note 1)
82
109
83.5 (Note 1)
82
109
92.5 (Note 1)
Custom
order
Motor valve with relay
Electric driven ball valve 3 port valve
(F)
(F)
MXB1D MXB1DF
H
G1/2
H
G1/2
Medical
analysis
46
46
CPE/
CPD
Note 1: For manual override "M", the MSB1 Series yoke is inserted between the valve and actuator, making dimensions 22 mm longer.
573
Electric driven ball valve 3 port valve with relay
(motor valve)
MXG1D Series
MXG1D Series
Port size: Rc1/2 to Rc2
Common specifications
MXG1D
Water, hot water, air, oil (500mm2/s or less)
0 to 1.0 (refer to working pressure range on individual specifications.)
2.0
0 to 80 (no freezing)
-10 to 50
95 or less
0 (under 1.0MPa or 0.5MPa (only for port size Rc2) water pressure)
Limited from vertical to horizontal installation placing motor top.
Limited to Port C pressurized.
Rainproof IPX3 (standard and option T only)
MXG1D-15
Individual specifications
Descriptions
MXG1D-15
Port size
Orifice
mm
Cv flow factor
Working pressure range MPa
50Hz
Interval when
activated
sec. 60Hz
Note 2
Cycle rate
Mass kg Bronze body
Stainless steel body
MXG1D-20
MXG1D-32
MXG1D-40
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
8
16
MXG1D-50
MXG1D-20
MXG1D-25
MXG1D-32
MXG1D-40
MXG1D-50
Rc1/2
Rc3/4
Rc1
Rc11/4
Rc11/2
Rc2
10
14
19
23
30
38
3
6
11
16
28
0 to 1.0
47
0 to 0.5
20
26
16
22
1 cycle/min. or less
1 cycle/2min. or less
1.3
1.5
1.7
2.7
3.3
4.2
1.3
1.5
1.7
2.8
3.4
4.3
Note 1: Allowable voltage range should be within 10% of rated voltage.
Note 2: Cycle rate should be within the specifications.
Note 3: consult with CKD about other than above specifications.
574
MXG1D-25
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
Starting Holding
Descriptions
Working fluid
Working pressure range MPa
Withstanding pressure (water) MPa
Fluid temperature
Ambient temperature
Ambient humidity
%
Valve seat leakage cm3/min
Installation attitude
Pressurization direction
Protection grade
Electrical specifications
Rated voltage Note 1
Apparent
100 VAC
power
VA 200 VAC
100 VAC
200 VAC
Power consumption W
MXG1D Series
How to order
HNB/G
MXG1D
20
0
K
2
USB/G
FAB/G
FGB/G
Series
Symbol
A Port size
15
Rc1/2
20
Rc3/4
25
Rc1
32
Rc11/4
40
Rc11/2
50
Rc2
A Port size
B
B Body/Seat
C
C Other options
*1
*2
D
D Voltage
<Example of model number>
MXG1D-20-0K-2
Descriptions
FVB
FWB/G
FHB
FLB
AB
Body/Seat
Body - bronze/Seat - PTFE
0
Body - bronze/Seat - reinforced PTFE
H
Body - stainless steel/Seat - PTFE
E
Body - stainless steel/Seat - reinforced PTFE
W
AG
AP/AD
Other options
Descriptions
Applications
Remarks
Blank 5-conductor 0.5mm2 (output lead wire)
2
T
3-conductor 0.75mm (no output) Output lead wire not required 3-conductor cabtire cord used
B
Round terminal box (5 cores) Optional lead wire length required
L
Round terminal box + light A-C flow path complete Lighting at operation complete
(ON at A-C flow path, 3-terminal) confirmation by light
of Flow path A-C
R
Round terminal box + light B-C flow path complete Lighting at operation complete
(ON at B-C flow path, 3-terminal) confirmation by light
of Flow path B-C
Multi fluids 90 degree turn switching To avoid pump load Both flows mixed
K
Operation time 1/2
type
during switching
For
dry air
Explosion
proof
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
CHB/G
Voltage
1
100 VAC (50/60Hz)
2
200 VAC (50/60Hz)
MXB/G
*1: When optional specifications of "C" is duplicate, select one from following combinations.
A 3 terminal round terminal box is provided for TB, TK, BK, LK, RK, TBK or TB.
*2: Combinations of LR, TL, TR, BL and BR aren't available for "C".
Other G.P.
systems
PD/FAD/
PJ
CVE/
CVSE
Series: MXG1D
CPE/
CPD
: Rc3/4
: Body - bronze/Seat - PTFE
: Multi fluids type (90 degree rotation switching method, operation time 1/2)
: 200VAC (50/60Hz)
Medical
analysis
Custom
order
Motor valve with relay
Electric driven ball valve 3 port valve
A Port size
B Body/Seat
C Other options
D Voltage
APK/
ADK
575
MXG1D Series
Internal structure and main parts material
MXG1D
1
2
18
3
4
5
6
7
13
8
14
15
9
16
10
19
20
17
11
12
A
B
C
No. Parts name
Material
1
2
3
4
5
6
7
8
9
10
Bonnet
ADC12
Aluminum alloy die-casting
Geared motor
-
-
Cam
PA
Polyamide
Gasket
NBR
Nitrile rubber
Micro switch
-
-
Adaptor
ZDC2
Zinc alloy die-casting
O ring
NBR
Nitrile rubber
Intermediate bush SUS303
Shaft
SUS303 (SUS304) Stainless steel (stainless steel)
Ball seat
PTFE
( ) shows values for stainless steel body
576
Stainless steel
Tetrafluoroethylene resin
No. Parts name
Material
11
12
13
14
15
16
17
18
19
20
Valve ball
C3771 (SUS304) Brass *2 (stainless steel)
Body
CAC407 (SCS13) Bronze casting (stainless steel casting)
P plate assembly PF
Phenol resin
O ring *1
FKM/NBR
Fluoro rubber/nitrile rubber
O ring
FKM
Fluoro rubber
Cap
CAC407 (SCS13) Bronze casting (stainless steel casting)
Hexagon head bolt SWCH
Carbon steel wire for cold forging
Cross headed pan SWCH
Carbon steel wire for cold forging
Bushing
PF
Phenol resin
Cabtire cord
0.5mm2, 5-conductor *1: Upper O ring is NBR, lower is FKM. For stainless steel,
FKM is used for both upper and lower O rings.
*2: Valve ball made of hard chrome plated brass.
MXG1D Series
Dimensions
MXG1D-15/20/25-*
55
MXG1D-32/40/50-*
(42)
40
63
(50)
54
64
HNB/G
80
USB/G
FAB/G
FGB/G
FWB/G
300
D
300
D
C
C
FVB
FHB
A
A
B
B
FLB
AB
3-E
A
AC
3-E
C
AG
B
B
Cabtire cord length 300mm
Cabtire cord length 300mm
Model
A
B
C
D
E
MXG1D-15-*
MXG1D-20-*
MXG1D-25-*
56
28
124.5
154.5
Rc1/2
65
34
130.5
166.5
Rc3/4
76
41
133.5
175.5
Rc1
AP/AD
Model
A
B
C
D
E
MXG1D-32-*
MXG1D-40-*
MXG1D-50-*
84
50
166
213
Rc11/4
94
57
172
225
Rc11/2
108
70
181
242
Rc2
APK/
ADK
For
dry air
Explosion
proof
HVB/
HVL
Optional dimensions
Round terminal box
MXG1D- Port size -* B
Round terminal box with indicator light
MXG1D- Port size -* L
R
(G)
SAB/
SVB
(G)
NP/NAP/
NVP
CHB/G
MXB/G
46
PD/FAD/
PJ
H
46
G1/2
H
G1/2
Other G.P.
systems
CVE/
CVSE
CPE/
CPD
(F)
Port size
F
G
H
Port size
F
G
H
15
20
25
32
40
50
74
96
58.5
74
101
58.5
74
96
64.5
74
101
64.5
74
96
67.5
74
101
67.5
82
104
77.5
82
109
77.5
82
104
83.5
82
109
83.5
82
104
92.5
15
20
25
32
40
50
82
109
92.5
Medical
analysis
Custom
order
Motor valve with relay
Electric driven ball valve 3 port valve
(F)
577
High corrosion proof electric driven ball valve 2 port valve with relay
(motor valve)
MXB1D-C Series
Port size: Rc1/2 to Rc2
Working fluid: Corrosive fluid
Common specifications
Descriptions
MXB1D-C
Working fluid
Working pressure rangeMPa
Withstanding pressure (with water pressure) MPa
Fluid temperature
Ambient temperature
Ambient humidity
Valve seat leakage cm3/min
Installation attitude
Pressurization direction
Protection grade
Corrosive fluid (not to corrode materials)
0 to 1.0 (refer to working pressure range on individual specifications.)
2.0
0 to 80 (no freezing)
-10 to 50
95 or less
0 (under 1.0MPa or 0.5MPa (only for port size Rc2) water pressure)
Limited from vertical to horizontal installation placing motor top.
Random
Rainproof IPX3 (standard and option T only)
Electrical specifications MXB1D-15-C MXB1D-20-C MXB1D-25-C MXB1D-32-C MXB1D-40-C MXB1D-50-C
Rated voltage
Apparent
power (VA)
Note 1
100 VAC
200 VAC
100 VAC
200 VAC
Power consumption W
Starting Holding
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
8
16
Individual specifications
Descriptions
MXB1D-15-C MXB1D-20-C MXB1D-25-C MXB1D-32-C MXB1D-40-C MXB1D-50-C
Port size
Orifice
mm
Cv flow factor
Working pressure range MPa
50Hz
Interval when
60Hz
activated sec.
Cycle rate
Note 2
kg
Mass
Rc1/2
Rc3/4
Rc1
Rc11/4
Rc11/2
Rc2
9.2
12.5
16
20
24.5
32
4.8
9
15.5
24
37
0 to 1.0
10
1.2
578
13
8
11
2 cycles/min. or less
1 cycle/min. or less
1.3
Note 1: Allowable voltage range should be within 10 of rated voltage.
Note 2: Cycle rate should be within the specifications.
Note 3: Consult with CKD about other than above specifications.
62
0 to 0.5
1.4
2.4
2.5
2.9
MXB1D-C Series
How to order
HNB/G
MXB1D
32
C T M
1
USB/G
FAB/G
FGB/G
Series
A
A Port size
B
B Body/Seat
C
C Other options
*1
*2
D Manual override
*3
E Voltage
D
E
Symbol
Port size
15
Rc1/2
20
Rc3/4
25
Rc1
32
Rc11/4
40
Rc11/2
50
Rc2
FVB
Descriptions
FWB/G
FHB
FLB
AB
Body/Sheet
C
Body - stainless steel/Seat - PTFE
AG
Other options
Descriptions
Applications
Remarks
Blank 5-conductor 0.5mm2 (output lead wire)
3-conductor 0.75mm2 (no output) Output lead wire not required 3-conductor cabtire cord used
T
Round terminal box (5 cores) Optional lead wire length required
B
Round terminal box + light (lighting at open) Fully open confir. by light Lighting at fully open
L
Round terminal box + light (lighting at closed) Fully closed confir. by light Lighting at fully closed
R
Manual override
Blank
Blank
Manual override
M
AP/AD
APK/
ADK
For
dry air
Explosion
proof
HVB/
HVL
SAB/
SVB
Voltage
100 VAC (50/60Hz)
1
200 VAC (50/60Hz)
2
NP/NAP/
NVP
*1: When selecting both no output ("C" T) and a round terminal box ("C" B) as options,
designate "C" as TB. A 3-terminal round terminal box will be provided.
*2: Combinations of LR, TL, TR, BL and BR aren't available for "C".
*3: Manual override ("D" is M) is available for port size 32, 40 and 50.
When port size is 15 to 25, manual override is equipped as standard.
CHB/G
MXB/G
Other G.P.
systems
PD/FAD/
PJ
<Example of model number>
MXB1D-32-CTM-1
CVE/
CVSE
Series: MXB1D-C
CPE/
CPD
A Port size
: Rc1 1/4
B Body/Seat
: Body - stainless steel/Seat - PTFE
C Other options : 3-conductor cable (no output)
D Manual override : Selected
E Voltage
: 100 VAC (50/60Hz)
Medical
analysis
High corrosion proof motor valve with relay
Electric driven ball valve 2 port valve
Custom
order
579
MXB1D-C Series
Internal structure and main parts material
MXB1D-*-C
1
2
17
3
4
5
6
13
14
7
15
8
9
16
19
10
20
18
11
12
No. Parts name
Material
1
2
3
4
5
6
7
8
9
10
Bonnet
ADC12
Aluminum alloy die-casting
Geared motor
-
-
Cam
PA
Polyamide
Gasket
NBR
Nitrile rubber
Micro switch
-
-
Adaptor
ZDC2
Zinc alloy die-casting
O ring
NBR
Nitrile rubber
580
Intermediate bush SUS303
Stainless steel
Shaft
SUS316
Stainless steel
Ball seat
PTFE
Tetrafluoroethylene resin
No. Parts name
Material
11
12
13
14
15
16
17
18
19
20
Valve ball
SUS316
Stainless steel
Body
SCS14
Stainless steel die casting
P plate assembly PF
Phenol resin
O ring
NBR
Nitrile rubber
O ring
FKM
Fluoro rubber
Insert
SUS316
Stainless steel
Hexagon head bolt SWCH
Carbon steel wire for cold forging
Cross headed pan SWCH
Carbon steel wire for cold forging
Bushing
PF
Phenol resin
Cabtire cord
0.5mm2, 5-conductor -
MXB1D-C Series
Dimensions
MXB1D-15/20/25-C
55
MXB1D-32/40/50-C
(42)
40
64
63
54
(50)
80
HNB/G
USB/G
FAB/G
FVB
300
300
D
D
C
C
FGB/G
FWB/G
B
FHB
FLB
2-E
B
A
2-E
A
AB
AG
Cabtire cord length 300 mm
Model
MXB1D-15-C
MXB1D-20-C
MXB1D-25-C
Cabtire cord length 300 mm
A
B
C
D
E
56.5
25
119
131.5
Rc1/2
59
32
121.5
137.5
Rc3/4
71
38
125.5
144.5
Rc1
Model
MXB1D-32-C
MXB1D-40-C
MXB1D-50-C
A
B
C
D
E
78
49
155.5
180
Rc11/4
83
53
161
187.5
Rc11/2
100
65
166.5
199
Rc2
Note 1: For manual override "M", the MSB1 Series yoke is inserted between
the valve and actuator, making dimensions C and D 22 mm longer.
AP/AD
APK/
ADK
For
dry air
Explosion
proof
HVB/
HVL
Optional dimensions
Round terminal box
MXB1D- Port size -C B
SAB/
SVB
Round terminal box with indicator light
MXB1D- Port size -C L
(G)
R
(G)
NP/NAP/
NVP
CHB/G
MXB/G
Other G.P.
systems
46
(F)
15
20
25
32
40
50
F
CVE/
CVSE
(F)
G
H
Port size
F
G
H
74
96
53
74
101
53
74
96
55.5
74
101
55.5
74
96
59.5
74
101
59.5
82
104
67 (Note 1)
82
109
67 (Note 1)
82
104
72.5 (Note 1)
82
109
72.5 (Note 1)
82
104
78 (Note 1)
15
20
25
32
40
50
82
109
78 (Note 1)
CPE/
CPD
Medical
analysis
Custom
order
High corrosion proof motor valve with relay
Electric driven ball valve 2 port valve
Port size
PD/FAD/
PJ
H
46
G1/2
H
G1/2
Note 1: For manual override "M", the MSB1 Series yoke is inserted between the valve and actuator, making dimensions 22 mm longer.
581
Electric driven oil prohibited ball valve 2 port valve
MXB1-N/MXB1D-N
(motorSeries
valve)
MXB1-N/MXB1D-N Series
Port size: Rc3/8 to Rc2
Common specifications
Descriptions
MXB1 (standard type) / MXB1D (with relay)
Working fluid
Water, hot water, air
Working pressure range MPa
0 to 1.0 (refer to working pressure range on individual specifications.)
Withstanding pressure (with water pressure) MPa
Fluid temperature
0 to 80 (no freezing)
2.0
Ambient temperature
-10 to 50
Ambient humidity
95 or less
Valve seat leakage cm3/min
Installation attitude
0 (under 1.0MPa or 0.5MPa (only for port size Rc2) water pressure)
Limited from vertical to horizontal installation placing motor top.
Pressurization direction
Random
Protection grade
Rainproof IPX3 (standard and option T only)
Electrical specifications
Descriptions
MXB1-10
Rated voltage
Starting Holding
MXB1-15
MXB1-20
MXB1-25
MXB1-32
MXB1-40
100 VAC
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
200 VAC
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
100 VAC
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
200 VAC
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
Average Ampere A 12 VDC
1.1
1.5
24 VDC
0.7
1.0
Peak Ampere A 12 VDC
1.8 or less
3 or less
24 VDC
Apparent
power VA
Note 2
1.2 or less
2 or less
AC
7
15
consumption W 12 VDC
13
18
24 VDC
17
Note 2
Power
Descriptions
MXB1D-10
Rated voltage
MXB1D-15
Starting Holding
24
MXB1D-20
MXB1D-25
MXB1D-32
MXB1D-40
100 VAC
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
200 VAC
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
100 VAC
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
200 VAC
W
Power consumption
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
8
16
power VA
MXB1D-50
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
Note 1
Apparent
MXB1-50
100 VAC (50/60Hz), 200 VAC (50/60Hz), 12 VDC and 24 VDC
Note 1
Individual specifications
MXB1-10
MXB1D-10
Descriptions
Port size
Orifice
mm
Cv flow factor
MXB1-15
MXB1D-15
MXB1-20
MXB1D-20
activated
sec.
Note 3
Mass
MXB1-50
MXB1D-50
Rc11/2
Rc2
Rc1/2
Rc3/4
Rc1
10
10
15
20
25
32
40
10
6
16
29
50
98
125
0 to 1.0
0 to 0.5
10/8 (50/60Hz)
13/11 (50/60Hz)
DC
8
10.5
AC
2 cycles/min. or less
1 cycle/min. or less
1 cycle/min. or less
DC
kg MXB1
MXB1D
1 cycle/2min. or less
1.2
1.2
1.4
1.5
2.6
3.1
3.8
1.2
1.3
1.4
1.6
2.7
3.1
3.9
Note 1: Allowable voltage range should be within 10 of rated voltage.
Note 2: Each ampere is the value when rated voltage.
Note 3: Cycle rate should be within the specifications.
Note 4: Consult with CKD about other than above specifications.
582
MXB1-40
MXB1D-40
Rc3/8
AC
Cycle rate
MXB1-32
MXB1D-32
Rc11/4
Working pressure range MPa
Interval when
MXB1-25
MXB1D-25
MXB1-N/MXB1D-N Series
How to order
MXB1
32
N T M
1
Series
MXB1D
Symbol
Port size
Series
MXB1 MXB1D
HNB/G
USB/G
Port size
A
A
Descriptions
10
Rc3/8
15
Rc1/2
20
Rc3/4
25
Rc1
32
Rc11/4
40
Rc11/2
50
Rc2
FAB/G
FGB/G
FVB
FWB/G
FHB
Body/Seat
B
B
Body/Seat
N
C
Other options
Descriptions
*1
*2
Blank
*3
Round terminal box Optional lead wire
(5 conductor)
length required
Lighting at
L
Round terminal box + light Fully open confir.
(lighting at open, 3 terminals) by light
Fully open confir. by light
Round terminal box + light
(lighting at closed, 3 terminals) Fully closed confir.
Lighting at
AP/AD
APK/
ADK
For
dry air
Explosion
proof
fully open
HVB/
HVL
fully closed
SAB/
SVB
Manual override
NP/NAP/
NVP
Blank Blank
Manual override
CHB/G
Voltage
E
Voltage
AG
(output lead wire)
B
M
E
Remarks
3-conductor cable 0.75 mm2 Output lead wire 3-conductor cabtire
cord used
(no output)
not required
D
Manual override
AB
Applications
5-conductor cable 0.5 mm2
T
R
D
FLB
Body - stainless steel / Seat - PTFE / Oil-prohibited specifications
Other options
C
1
100 VAC (50/60Hz)
2
200 VAC (50/60Hz)
3
24 VDC
4
12 VDC
MXB/G
Other G.P.
systems
*1: When selecting both no output ("C" T) and a round terminal box ("C" B) as options,
designate "C" as TB. A 3-terminal round terminal box will be provided.
*2: Combinations of LR, TL, TR, BL and BR aren't available for "C".
*3: Manual override ("D" is M) is available for port size 32, 40 and 50.
When port size is 10 to 25, manual override is equipped as standard.
<Example of model number>
: Rc1 1/4
: Body - stainless steel / Seat- PTFE / Oil-prohibited specifications
: 3 conductor cable (no output)
: Selected
: 100 VAC (50/60Hz)
Oil prohibited motor valve
Electric driven ball valve 2 port valve
Port size
Body material
Other options
D Manual override
E Voltage
B
CPE/
CPD
Custom
order
Series: MXB1 (standard type)
C
CVE/
CVSE
Medical
analysis
MXB1-32-NTM-1
A
PD/FAD/
PJ
583
MXB1-N/MXB1D-N Series
Internal structure and main parts material
MXB1/MXB1D
1
2
3
19
4
5
20
6
21
7
13
8
14
9
15
10
16
11
18
17
12
Parts name
Material
Parts name
Material
1
Bonnet
ADC12
Aluminum alloy die-casting
11
Valve ball
SUS304
Stainless steel
2
Geared motor
-
-
12
Body
SCS13
Stainless steel die casting
3
Cam
PA
Polyamide
13
P plate assembly PF
Phenol resin
4
Gasket
NBR
Nitrile rubber
14
O ring
FKM
Fluoro rubber
5
Micro switch
-
-
15
Sealing ring
UHMW-PE
Ultra high molecular weight polyethylene
6
Adaptor
ZDC2
Zinc alloy die-casting
16
O ring
FKM
Fluoro rubber
7
O ring
NBR
Nitrile rubber
17
Cap
SCS13
Stainless steel die casting
8
Intermediate bush SUS303
Stainless steel
18
Hexagon head bolt SWCH
Carbon steel wire for cold forging
9
Shaft
SUS304
Stainless steel
19
Cross headed pan SWCH
Carbon steel wire for cold forging
10
Ball seat
PTFE
Tetrafluoroethylene resin
20
Bushing
PF
Phenol resin
21
Cabtire cord
0.5mm2, 5-conductor -
No.
584
No.
MXB1-N/MXB1D-N Series
Dimensions
MXB1/MXB1D-10/15/20/25-N
MXB1/MXB1D-32/40/50-N
(42)
55
64
63
40
HNB/G
(50)
54
80
USB/G
FAB/G
FGB/G
FWB/G
300
300
D
D
C
C
FVB
FHB
FLB
AB
AG
2-E
B
A
B
A
2-E
AP/AD
APK/
ADK
Cabtire cord length 300mm
Cabtire cord length 300mm
Model
A
B
C
D
E
Model
A
B
C
D
E
MXB1 (D)-10-N
56
28
124.5
140.5
Rc3/8
MXB1 (D)-32-N
84
50
166
195.5
Rc11/4
MXB1 (D)-15-N
56
28
124.5
140.5
Rc1/2
MXB1 (D)-40-N
94
57
172
207.5
Rc11/2
MXB1 (D)-20-N
65
34
130.5
151
Rc3/4
MXB1 (D)-50-N
108
70
181
221.5
Rc2
MXB1 (D)-25-N
76
41
133.5
157.5
Rc1
For
dry air
Explosion
proof
HVB/
HVL
Note 1: For manual override "M", the MSB1 Series yoke is inserted between
the valve and actuator, making dimensions C and D 22 mm longer.
SAB/
SVB
NP/NAP/
NVP
Optional dimensions
Round terminal box
MXB1/MXB1D- Port size -N B
Round terminal box with indicator light
MXB1/MXB1D- Port size -N L
R
(G)
CHB/G
(G)
MXB/G
Other G.P.
systems
PD/FAD/
PJ
46
F
H
Port size
F
G
H
10
74
96
58.5
10
74
101
58.5
15
74
96
58.5
15
74
101
58.5
20
74
96
64.5
20
74
101
64.5
25
74
96
67.5
25
74
101
67.5
32
82
104
77.5 (Note 1)
32
82
109
77.5 (Note 1)
40
82
104
83.5 (Note 1)
40
82
109
83.5 (Note 1)
50
82
104
92.5 (Note 1)
50
82
109
92.5 (Note 1)
Oil prohibited motor valve
Electric driven ball valve 2 port valve
Port size
Medical
analysis
Custom
order
(F)
(F)
G
CPE/
CPD
H
46
G1/2
H
G1/2
CVE/
CVSE
Note 1: For manual override "M", the MSB1 Series yoke is inserted between the valve and actuator, making dimensions 22 mm longer.
585
Electric driven oil prohibited ball valve 3 port valve
MXG1-N/MXG1D-N
(motor Series
valve)
MXG1-N/MXG1D-N Series
Port size: Rc1/2 to Rc2
Common specifications
Descriptions
MXG1 (standard type) / MXG1D (with relay)
Working fluid
Water, hot water, air
Working pressure range MPa
Withstanding pressure (water) MPa
0 to 1.0 (refer to working pressure range on individual specifications.)
2.0
Fluid temperature
0 to 80 (no freezing)
Ambient temperature
-10 to 50
Ambient humidity
95 or less
%
Valve seat leakage cm3/min
Installation attitude
0 (under 1.0MPa or 0.5MPa (only for port size Rc2) water pressure)
Limited from vertical to horizontal installation placing motor top.
Pressurization direction
Limited to Port C pressurized.
Protection grade
Rainproof IPX3 (standard and option T, K only)
Electrical specifications
Descriptions
MXG1-15
Rated voltage
Starting Holding
MXG1-20
MXG1-25
MXG1-32
MXG1-40
100 VAC
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
200 VAC
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
100 VAC
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
200 VAC
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
Average Ampere A 12 VDC
1.1
1.5
Note 2 24 VDC
0.7
1.0
Peak Ampere A 12 VDC
1.8 or less
3 or less
Note 2 24 VDC
Apparent
power
VA
1.2 or less
2 or less
AC
7
15
12 VDC
13
18
24 VDC
17
Power consumption W
Descriptions
MXG1D-15
Rated voltage
24
MXG1D-20
Starting Holding
MXG1D-25
MXG1D-32
MXG1D-40
MXG1D-50
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
Note 1
100 VAC
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
200 VAC
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
100 VAC
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
200 VAC
W
Power consumption
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
8
16
Apparent power VA
MXG1-50
100 VAC (50/60Hz), 200 VAC (50/60Hz), 12 VDC and 24 VDC
Note 1
Individual specifications
MXG1-15
MXG1D-15
Descriptions
Port size
Orifice
mm
Cv flow factor
MXG1-20
MXG1D-20
activated
Cycle rate
Mass
sec.
MXG1-40
MXG1D-40
Rc11/2
Rc2
38
Rc1/2
Rc3/4
Rc1
10
14
19
23
30
3
6
11
16
28
0 to 1.0
AC
20/16 (50/60Hz)
16
21
AC
1 cycle/min. or less
1 cycle/2min. or less
Note 3
DC
kg MXG1
MXG1-50
MXG1D-50
47
0 to 0.5
DC
MXG1D
26/22 (50/60Hz)
1 cycle/2min. or less
1 cycle/5min. or less
1.3
1.4
1.7
2.7
3.2
4.1
1.3
1.5
1.7
2.7
3.3
4.2
Note 1: Allowable voltage range should be within 10% of rated voltage.
Note 2: Each ampere is the value when rated voltage.
Note 3: Cycle rate should be within the specifications.
Note 4: Consult with CKD about other than above specifications.
586
MXG1-32
MXG1D-32
Rc11/4
Working pressure range MPa
Interval when
MXG1-25
MXG1D-25
MXG1-N/MXG1D-N Series
How to order
MXG1
20
N K
2
Series
MXG1D
Symbol
Port size
Series
15
Rc1/2
20
Rc3/4
25
Rc1
32
Rc11/4
40
Rc11/2
50
Rc2
Body/Seat
N
Other options
*1
*2
FWB/G
FHB
FLB
Applications
Remarks
AB
5-conductor cable 0.5 mm2
(output lead wire)
AG
T
3-conductor cable 0.75 mm2 Output lead wire 3-conductor cabtire
cord used
(no output)
not required
AP/AD
B
Round terminal box Optional lead wire
(5 conductor)
length required
APK/
ADK
L
A-C flow path completion Lighting whenA-C
Round terminal box + light
flow path completed
(ON at A-C flow path, 3-terminal) confirmation by light
R
B-C flow path completion B-C flow path
Round terminal box + light
(ON at B-C flow path, 3-terminal) confirmation by light
K
Both flows mixed
Multi fluids 90˚ turn switching
To avoid pump load
Operation time 1/2
during switching
type
For
dry air
Explosion
proof
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
Voltage
D
Voltage
FVB
Body - stainless steel / Seat - PTFE / Oil-prohibited specifications
Descriptions
Blank
D
1
100 VAC (50/60Hz)
2
200 VAC (50/60Hz)
3
24 VDC
4
12 VDC
CHB/G
MXB/G
*1: When optional specifications of "C" is duplicate, select one from following combinations.
TB, TK, BK, LK, RK and TBK A 3-terminal round terminal box will be provided.
*2: Combinations of LR, TL, TR, BL and BR aren't available for "C".
<Example of model number>
Series: MXG1
C
D
Port size
Body/Seat
Other options
Voltage
PD/FAD/
PJ
CPE/
CPD
: Rc3/4
: Body - stainless steel / Seat - PTFE / Oil-prohibited specifications
: Multi fluids type (90 degree rotation switching method, operation time 1/2)
: 200 VAC (50/60Hz)
Medical
analysis
Custom
order
Oil prohibited motor valve
Electric driven ball valve 3 port valve
B
Other G.P.
systems
CVE/
CVSE
MXG1-20-NK-2
A
USB/G
FGB/G
Other options
C
C
HNB/G
FAB/G
Body/Seat
B
B
MXG1 MXG1D
Port size
A
A
Descriptions
587
MXG1-N/MXG1D-N Series
Internal structure and main parts material
MXG1/MXG1D
1
2
3
19
4
5
20
6
21
7
13
8
14
9
15
10
16
11
18
17
A
B
12
C
Parts name
Material
Parts name
Material
1
Bonnet
ADC12
Aluminum alloy die-casting
11
Valve ball
SUS304
Stainless steel
2
Geared motor
-
-
12
Body
SCS13
Stainless steel die casting
3
Cam
PA
Polyamide
13
P plate assembly PF
Phenol resin
4
Gasket
NBR
Nitrile rubber
14
O ring
FKM
Fluoro rubber
5
Micro switch
-
-
15
Sealing ring
UHMW-PE
Ultra high molecular weight polyethylene
6
Adaptor
ZDC2
Zinc alloy die-casting
16
O ring
FKM
Fluoro rubber
7
O ring
NBR
Nitrile rubber
17
Cap
SCS13
Stainless steel die casting
8
Intermediate bush SUS303
Stainless steel
18
Hexagon head bolt SWCH
Carbon steel wire for cold forging
9
Shaft
SUS304
Stainless steel
19
Cross headed pan SWCH
Carbon steel wire for cold forging
10
Ball seat
PTFE
Tetrafluoroethylene resin
20
Bushing
PF
Phenol resin
21
Cabtire cord
0.5mm2, 5-conductor -
No.
588
No.
MXG1-N/MXG1D-N Series
Dimensions
MXG1/MXG1D-15/20/25-N
MXG1/MXG1D-32/40/50-N
(42)
40
55
HNB/G
(50)
63
64
54
80
USB/G
FAB/G
FGB/G
C
C
FVB
300
D
300
D
FWB/G
FHB
FLB
A
B
A
AB
B
AG
3-E
C
A
AP/AD
3-E
B
C
A
APK/
ADK
B
For
dry air
Cabtire cord length 300mm
Cabtire cord length 300mm
Model
A
B
C
D
E
MXG1 (D)-15-N
56
28
124.5
154.5
Rc1/2
MXG1 (D)-20-N
65
34
130.5
166.5
Rc3/4
MXG1 (D)-25-N
76
41
133.5
175.5
Rc1
Model
A
B
C
D
E
MXG1 (D)-32-N
84
50
166
213
Rc11/4
MXG1 (D)-40-N
94
57
172
225
Rc11/2
MXG1 (D)-50-N
108
70
181
242
Rc2
Explosion
proof
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
Optional dimensions
Round terminal box
MXG1/MXG1D- Port size -N B
Round terminal box with indicator light
MXG1/MXG1D- Port size -N L
R
(G)
CHB/G
(G)
MXB/G
Other G.P.
systems
PD/FAD/
PJ
H
46
H
46
CVE/
CVSE
G1/2
G1/2
CPE/
CPD
Medical
analysis
Custom
order
(F)
Port size
F
G
H
Port size
F
G
H
15
74
96
58.5
15
74
101
58.5
20
74
96
64.5
20
74
101
64.5
25
74
96
67.5
25
74
101
67.5
32
82
104
77.5
32
82
109
77.5
40
82
104
83.5
40
82
109
83.5
50
82
104
92.5
50
82
109
92.5
Oil prohibited motor valve
Electric driven ball valve 3 port valve
(F)
589
Electric driven ball valve 2 port valve for steam
MSB1/MSB1F Series
(motor valve)
MSB1/MSB1F Series
Port size: Rc3/8 to Rc2
Common specifications
MSB1 (standard bore)/MSB1F (full bore)
Descriptions
Working fluid
Working pressure range MPa
Withstanding pressure (water) MPa
Ambient temperature
%
Ambient humidity
Valve seat leakage cm3/min
Installation attitude
Pressurization direction
Protection grade
Electrical specifications
2.0
-10 to 50
95 or less
1 or less (Note when pressure is 0.6MPa, or for MSB1-50/MSB1F-40 when pressure is 0.5MPa)
Limited from vertical to horizontal installation placing motor top.
Random
Rainproof IPX3 (standard and option T only)
MSB1-10
MSB1-15
MSB1F-15
MSB1-20
MSB1-25
MSB1F-20
100 VAC
200 VAC
100 VAC
200 VAC
Power consumption W AC
MSB1-32
MSB1F-25
MSB1-40
MSB1F-32
4.9/5.9 (50/60Hz)
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
13/15 (50/60Hz)
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
4.9/5.9 (50/60Hz)
13/15 (50/60Hz)
5.4/6.2 (50/60Hz)
13/15 (50/60Hz)
7
15
Note 1
Starting Holding
Rated voltage
Apparent
power
VA
Steam, hot water
0 to 0.6 (refer to working pressure range on individual specifications.)
MSB1-50
MSB1F-40
MSB1 (standard bore) individual specifications
Descriptions
MSB1-10 Note 2
Rc3/8
Port size
10
Orifice
mm
10
Cv flow factor
Working pressure range MPa
Fluid temperature
Interval when
50Hz
activated sec. 60Hz
Note 3
Cycle rate
kg
1.3
Mass
MSB1-15
MSB1-20
MSB1-25
MSB1-32
MSB1-40
MSB1-50
Rc1/2
Rc3/4
Rc1
Rc11/4
Rc11/2
Rc2
10
15
20
25
32
40
6
16
29
50
98
125
0 to 0.6
0 to 0.5
0 to 164 (no freezing)
0 to 158
13
10
11
8
1 cycle/min. or less
1.3
1.4
1.6
2.6
MSB1F (full bore) individual specifications
Descriptions
MSB1F-15 MSB1F-20 MSB1F-25 MSB1F-32
Rc1/2
Rc3/4
Rc1
Rc11/4
Port size
32
15
20
25
Orifice
mm
114
23
51
66
Cv flow factor
0 to 0.6
Working pressure range MPa
0 to 164 (no freezing)
Fluid temperature
10
Interval when
13
50Hz
8
activated
11
sec. 60Hz
1 cycle/min. or less
Note 3
Cycle rate
kg
3.1
1.4
1.6
2.6
Mass
Note 1: Allowable voltage range should be within 10% of rated voltage.
Note 2: MSB1-10 is a full bore.
Note 3: Cycle rate should be within the specifications.
Note 4: Consult with CKD about other than above specifications.
590
MSB1F-40
Rc11/2
40
176
0 to 0.5
0 to 158
3.8
3.1
3.8
MSB1/MSB1F Series
How to order
MSB1
32
H
T M
1
HNB/G
MSB1F
Symbol
Series
A
A Port size
B
B Body/Seat
C
C Other options
*1
*2
Other options
Descriptions
5-conductor cable 0.5 mm2
Blank
(output lead wire)
B
L
R
E Voltage
D
E
USB/G
FAB/G
*4
FGB/G
FVB
FWB/G
FHB
Body/Seat
H
Body - bronze/Seat - reinforced PTFE
W
Stainless steel-reinforced Teflon
T
D Manual override
*3
Descriptions
Port size
Rc3/8
10
Rc1/2
15
Rc3/4
20
Rc1
25
Rc11/4
32
Rc11/2
40
Rc2
50
Series
MSB1 MSB1F
(Standard bore) (Full bore)
Applications
3-conductor cable 0.75 mm2 Output lead
wire not required
(no output)
FLB
AB
AG
Remarks
AP/AD
APK/
ADK
3-conductor cabtire
cord used
For
dry air
Round terminal box Optional lead wire
(5 conductor)
length required
Round terminal box + light Fully open confir.
Lighting at fully open
(ON when open, 3 terminal) by light
Explosion
proof
HVB/
HVL
Round terminal box + light Fully open confir. by light
Lighting at fully closed
(OFF when closed, 3 terminal) Fully closed confir.
SAB/
SVB
Manual override
Blank
Blank
M
Manual override
NP/NAP/
NVP
Voltage
1
100 VAC (50/60Hz)
2
200 VAC (50/60Hz)
CHB/G
MXB/G
*1: When selecting both no output ("C" T) and a round terminal box ("C" B) as options,
designate "C" as TB. A 3-terminal round terminal box will be provided.
*2: Combinations of LR, TL, TR, BL and BR aren't available for "C".
*3: For manual override ("D" M), port size 32, 40, or 50 is selected for MSB1.
For MSB1F, 25, 32, or 40 is selected.
When port size is 10 to 25, manual override is equipped as standard.
*4: The port size 10 is a full bore, but the model is MSB1.
Other G.P.
systems
PD/FAD/
PJ
CVE/
CVSE
CPE/
CPD
Medical
analysis
<Example of model number>
MSB1-32-HTM-1
Custom
order
A Port size
B Body/Seat
C Other options
D Manual override
E Voltage
Motor valve for steam
Electric driven ball valve 2 port valve
Series: MSB1 (standard bore)
: Rc1 1/4
: Body - bronze/Seat - reinforced PTFE
: 3 conductor cable (no output)
: Selected
: 100 VAC (50/60Hz)
591
MSB1/MSB1F Series
Internal structure and main parts material
MSB1/MSB1F
1
2
18
3
4
5
6
13
7
14
8
15
9
16
10
19
20
17
21
11
12
No. Parts name
Material
1
2
3
4
5
6
7
8
9
10
Bonnet
ADC12
Aluminum alloy die-casting
Geared motor
-
-
Cam
PA
Polyamide
Gasket
NBR
Nitrile rubber
Micro switch
-
-
Adaptor
ZDC2
Zinc alloy die-casting
O ring
NBR
Nitrile rubber
Intermediate bush SUS303
Shaft
SUS303 (SUS304) Stainless steel (stainless steel)
Ball seat
Reinforced Teflon -
( ) shows values for stainless steel body
592
Stainless steel
No. Parts name
Material
11
12
13
14
15
16
17
18
19
20
21
Valve ball
C3771 (SUS304) Brass *1 (stainless steel)
Body
CAC407 (SCS13) Bronze casting (stainless steel casting)
P plate assembly PF
Phenol resin
O ring
FKM
Fluoro rubber
O ring
FKM
Fluoro rubber
Cap
CAC407 (SCS13) Bronze casting (stainless steel casting)
Hexagon nut
SWCH
Carbon steel wire for cold forging
Cross headed pan SWCH
Carbon steel wire for cold forging
Bushing
PF
Phenol resin
Cabtire cord
0.5mm2, 5-conductor
-
Yoke
PM-HH
Phenol resin
*1: Valve ball is made of hard chrome plated brass.
MSB1/MSB1F Series
Dimensions
(Page 613)
MSB1-10/15/20/25-*
MSB1F-15/25-H
55
MSB1-32/40/50-*
MSB1F-25/32/40-H
(42)
40
HNB/G
54
64
63
(50)
80
USB/G
FAB/G
FGB/G
300
300
D
D
C
C
FVB
FWB/G
FHB
FLB
AB
2-E
A
2-E
B
MSB1-10-*
MSB1-15-*
MSB1-20-*
MSB1-25-*
MSB1F-15-H
MSB1F-20-H
B
AG
Cabtire cord length 300 mm
Model
A
Cabtire cord length 300 mm
A
B
C
D
E
50 (56)
24 (28)
146.5
161.5 (162.5)
Rc3/8
56
28
146.5
161.5 (162.5)
Rc1/2
65
34
152.5
172 (173)
Rc3/4
76
41
155.5
178.5 (179.5)
Rc1
65
28
152.5
172
Rc1/2
71
34
155.5
178.5
Rc3/4
Note 1: ( ) shows values for stainless steel body
Model
MSB1-32-*
MSB1-40-*
MSB1-50-*
MSB1F-25-H
MSB1F-32-H
MSB1F-40-H
AP/AD
A
B
C
D
E
84
50
188
215.5 (217.5)
Rc11/4
94
57
194
227.5 (229.5)
Rc11/2
108
70
203
242.5 (243.5)
Rc2
84
41
188
215.5
Rc1
95
50
194
227.5
Rc11/4
107
57
203
242.5
Rc11/2
HVB/
HVL
Note 1: Dimensions do not change when the manual override "M" is provided.
Note 2: ( ) shows values for stainless steel body
SAB/
SVB
APK/
ADK
For
dry air
Explosion
proof
NP/NAP/
NVP
Optional dimensions
Round terminal box with indicator light
MSB1- Port size -* L
R
MSB1F- Port size -H L
R
(G)
Other G.P.
systems
PD/FAD/
PJ
46
H
G1/2
CHB/G
MXB/G
46
(G)
G1/2
(F)
CVE/
CVSE
H
Round terminal box
MSB1- Port size -* B
MSB1F- Port size -H B
CPE/
CPD
(F)
Medical
analysis
10
15
20
25
32
40
50
15
20
25
32
40
F
G
H
74
96
80.5
74
96
80.5
74
96
86.5
74
96
89.5
82
104
99.5
82
104
105.5
82
104
114.5
Note 1: Dimensions do not change for large port size (32 to 50)
when the manual override "M" is provided.
Port size
MSB1 MSB1F
10
15
20
25
32
40
50
15
20
25
32
40
F
G
H
74
101
80.5
74
101
80.5
74
101
86.5
74
101
89.5
82
109
99.5
82
109
105.5
82
109
114.5
Custom
order
Motor valve for steam
Electric driven ball valve 2 port valve
Port size
MSB1 MSB1F
Note 1: Dimensions do not change for large port size (32 to 50)
when the manual override "M" is provided.
593
driven ball valve 2 port valve for steam with relay
MSB1D/MSB1DFElectric
Series
(motor
valve)
MSB1D/MSB1DF Series
Port size: Rc3/8 to Rc2
Common specifications
MSB1D (standard bore) / MSB1DF (full bore)
Descriptions
Working fluid
Working pressure range MPa
Withstanding pressure (water) MPa
Ambient temperature
%
Ambient humidity
Valve seat leakage cm3/min
Installation attitude
Pressurization direction
Protection grade
Electrical specifications
2.0
-10 to 50
95 or less
1 or less (Note when pressure is 0.6MPa, or for MSB1D-50/MSB1DF-40 when pressure is 0.5MPa)
Limited from vertical to horizontal installation placing motor top.
Random
Rainproof IPX3 (standard and option T only)
MSB1D-10 MSB1D-15
MSB1DF-15
MSB1D-20 MSB1D-25 MSB1D-32 MSB1D-40 MSBD1-50
MSB1DF-25 MSB1DF-32 MSB1DF-40
MSB1DF-20
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
Note 1
Starting Holding
Rated voltage
Apparent
power
VA
Steam, hot water
0 to 0.6 (refer to working pressure range on individual specifications.)
100 VAC
200 VAC
100 VAC
200 VAC
Power consumption W
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
6.0/6.8 (50/60Hz)
14/16 (50/60Hz)
6.6/7.2 (50/60Hz)
14/16 (50/60Hz)
8
16
MSB1D (standard bore) individual specifications
Descriptions
MSB1D-10 Note 2 MSB1D-15 MSB1D-20 MSB1D-25 MSB1D-32
Rc3/8
Rc1/2
Rc3/4
Rc1
Rc11/4
Port size
25
10
10
15
20
Orifice
mm
50
10
6
16
29
Cv flow factor
0 to 0.6
Working pressure range MPa
0 to 164 (no freezing)
Fluid temperature
10
Interval when
50Hz
8
activated sec. 60Hz
Note 3
1 cycle/min. or less
Cycle rate
kg
2.6
1.3
1.3
1.5
1.6
Mass
MSB1DF (full bore) individual specifications
Descriptions
MSB1DF-15 MSB1DF-20 MSB1DF-25 MSB1DF-32 MSB1DF-40
Rc1/2
Rc11/2
Rc3/4
Rc1
Rc11/4
Port size
32
40
15
20
25
Orifice
mm
114
176
23
51
66
Cv flow factor
0 to 0.6
0 to 0.5
Working pressure range MPa
0 to 164 (no freezing)
0 to 158
Fluid temperature
10
Interval when
13
50Hz
8
activated sec. 60Hz
11
1 cycle/min. or less
Note 3
Cycle rate
kg
3.1
3.9
1.5
1.6
2.6
Mass
Note 1: Allowable voltage range should be within 10% of rated voltage.
Note 2: MSB1D-10 is a full bore.
Note 3: Cycle rate should be within the specifications.
Note 4: Consult with CKD about other than above specifications.
594
MSB1D-40
MSB1D-50
Rc11/2
Rc2
32
40
98
125
0 to 0.5
0 to 158
13
11
3.1
3.9
MSB1D/MSB1DF Series
How to order
HNB/G
MSB1D
32
H
T M
1
USB/G
MSB1DF
FAB/G
Series
Symbol
Series
A
A Port size
FWB/G
FHB
FLB
C
Other options
Descriptions
E
Applications
AB
AG
AP/AD
Remarks
5-conductor cable 0.5 mm2
(output lead wire)
APK/
ADK
T
3-conductor cable 0.75 mm2 Output lead wire 3-conductor cabtire
(no output)
not required
cord used
For
dry air
B
Round terminal box Optional lead wire
length required
(5 conductor)
Explosion
proof
L
Round terminal box + light Fully open confir.
Lighting at fully open
(ON when open, 3 terminal) by light
R
Round terminal box + light Fully open confir. by light
Lighting at fully closed
(OFF when closed, 3 terminal) Fully closed confir.
Blank
D
FGB/G
FVB
*4
Body/Seat
Body - bronze/Seat - reinforced PTFE
H
Stainless steel - reinforced Teflon
W
C Other options
*1
*2
E Voltage
Descriptions
Port size
Rc3/8
10
Rc1/2
15
Rc3/4
20
Rc1
25
Rc11/4
32
Rc11/2
40
Rc2
50
B
B Body/Seat
D Manual override
*3
MSB1D MSB1DF
(Standard bore) (Full bore)
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
Manual override
Blank
Blank
Manual override
M
CHB/G
Voltage
100 VAC (50/60Hz)
1
200 VAC (50/60Hz)
2
MXB/G
Other G.P.
systems
*1. When selecting both no output ("C" T) and a round terminal box ("C" B) as options,
designate "C" as TB. A 3-terminal round terminal box will be provided.
*2: Combinations of LR, TL, TR, BL and BR aren't available for "C".
*3: For manual override ("D" M), port size 32, 40, or 50 is selected for MSB1D.
For MSB1DF, 25, 32, or 40 is selected.
When port size is 10 to 25, manual override is equipped as standard.
*4: The port size 10 is a full bore, but the model is MSB1D.
PD/FAD/
PJ
CVE/
CVSE
CPE/
CPD
Medical
analysis
Custom
order
Motor valve for steam with relay
Electric driven ball valve 2 port valve
<Example of model number>
MSB1D-32-HTM-2
Series: MSB1D (standard bore)
A Port size
B Body/Seat
C Other options
D Manual override
E Voltage
: Rc1 1/4
: Body - bronze/Seat - reinforced PTFE
: 3 conductor cable (no output)
: Selected
: 200 VAC (50/60Hz)
595
MSB1D/MSB1DF Series
Internal structure and main parts material
MSB1D/MSB1DF
1
2
18
3
4
5
6
13
7
14
8
15
9
16
10
19
20
17
21
11
12
No. Parts name
Material
1
2
3
4
5
6
7
8
9
10
Bonnet
ADC12
Aluminum alloy die-casting
Geared motor
-
-
Cam
PA
Polyamide
Gasket
NBR
Nitrile rubber
Micro switch
-
-
Adaptor
ZDC2
Zinc alloy die-casting
O ring
NBR
Nitrile rubber
Intermediate bush SUS303
Shaft
SUS303 (SUS304) Stainless steel (stainless steel)
Ball seat
Reinforced Teflon
( ) shows values for stainless steel body
596
Stainless steel
-
No. Parts name
Material
11
12
13
14
15
16
17
18
19
20
21
Valve ball
C3771 (SUS304) Brass *1 (stainless steel)
Body
CAC407 (SCS13) Bronze casting (stainless steel casting)
P plate assembly PF
Phenol resin
O ring
FKM
Fluoro rubber
O ring
FKM
Fluoro rubber
Cap
CAC407 (SCS13) Bronze casting (stainless steel casting)
Hexagon nut
SWCH
Carbon steel wire for cold forging
Cross headed pan SWCH
Carbon steel wire for cold forging
Bushing
PF
Phenol resin
Cabtire cord
0.5mm2, 5-conductor -
Yoke
PM-HH
Phenol resin
*1: Valve ball made of hard chrome plated brass.
MSB1D/MSB1DF Series
Dimensions
MSB1D-10/15/20/25-*
MSB1DF-15/20-H
55
MSB1D-32/40/50-*
MSB1DF-25/32/40-H
HNB/G
(42)
40
63
54
64
(50)
80
USB/G
FAB/G
FGB/G
300
D
300
C
D
C
FVB
FWB/G
FHB
FLB
AB
2-E
A
B
2-E
Cabtire cord length 300 mm
Model
MSB1D-10-*
MSB1D-15-*
MSB1D-20-*
MSB1D-25-*
MSB1DF-15-H
MSB1DF-20-H
B
A
AG
AP/AD
Cabtire cord length 300 mm
A
B
C
D
E
50 (56)
24 (28)
146.5
161.5 (162.5)
Rc3/8
56
28
146.5
161.5 (162.5)
Rc1/2
65
34
152.5
172 (173)
Rc3/4
76
41
155.5
178.5 (179.5)
Rc1
65
28
152.5
172
Rc1/2
71
34
155.5
178.5
Rc3/4
Model
A
B
C
D
E
MSB1D-32-*
MSB1D-40-*
MSB1D-50-*
MSB1DF-25-H
MSB1DF-32-H
MSB1DF-40-H
84
50
188
215.5 (217.5)
Rc11/4
94
57
194
227.5 (229.5)
Rc11/2
108
70
203
242.5 (243.5)
Rc2
84
41
188
215.5
Rc1
95
50
194
227.5
Rc11/4
107
57
203
242.5
Rc11/2
Note 1: Dimensions do not change when the manual override "M" is provided.
APK/
ADK
For
dry air
Explosion
proof
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
Optional dimensions
Round terminal box
MSB1D- Port size -* B
MSB1DF- Port size -H B
Round terminal box with indicator light
MSB1D- Port size -* L
R
MSB1DF- Port size -H L
R
(G)
(G)
CHB/G
MXB/G
PD/FAD/
PJ
H
46
46
Other G.P.
systems
G1/2
CVE/
CVSE
(F)
CPE/
CPD
H
G1/2
(F)
Medical
analysis
10
15
20
25
32
40
50
15
20
25
32
40
F
G
H
74
96
80.5
74
96
80.5
74
96
86.5
74
96
89.5
82
104
99.5
82
104
105.5
82
104
114.5
Note 1: Dimensions do not change for large port size (32 to 50)
when the manual override "M" is provided.
Port size
MSB1D MSB1DF
10
15
20
25
32
40
50
15
20
25
32
40
F
G
H
74
101
80.5
74
101
80.5
74
101
86.5
74
101
89.5
82
109
99.5
82
109
105.5
82
109
114.5
Custom
order
Motor valve for steam with relay
Electric driven ball valve 2 port valve
Port size
MSB1D MSB1DF
Note 1: Dimensions do not change for large port size (32 to 50)
when the manual override "M" is provided.
597
driven ball valve 2, 3 port valve proportional control
MXBC/MXGC SeriesElectric
(motor valve)
MXBC/MXGC Series
Port size: Rc3/8 to Rc1
Common specifications
MXBC
Descriptions
Working fluid
Working pressure range MPa
Withstanding pressure (with water pressure) MPa
Fluid temperature
Ambient temperature
Ambient humidity
%
Valve seat leakage cm3/min
Installation attitude
Pressurization direction
Protection grade
MXGC
Water, hot water
0 to 1.0
2.0
0 to 80 (no freezing)
-10 to 50
95 or less
0 (under 1.0MPa water pressure)
Limited from vertical to horizontal installation placing motor top.
Random
Limited to C port pressurizing
Rainproof IPX
Electrical specifications
Standard type
Descriptions
Rated voltage Note 1
Consumption current (average) mA
Input signal
Resolution
Descriptions
Rated voltage Note 1
Apparent
100 VAC
power
200 VAC
VA
100 VAC
200 VAC
Power consumption W
Interval when activated sec.
24 VDC
750
100
DC0(4) to 20mA, internal impedance 240 ohm (fully closed: 0mA)
2.5% or less
Simple control type
Starting Holding
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
4.9/5.9 (50/60Hz)
5.4/6.2 (50/60Hz)
4.9/5.9 (50/60Hz)
5.4/6.2 (50/60Hz)
7
10/8 (50/60Hz)
Note 1: Keep the allowable voltage range to within
10% of the rated voltage.
Individual specifications
2 port valve
Descriptions
Port size
Orifice
mm
Cv flow factor
Max. ON/OFF frequency
Interval when activated sec.
Mass
kg
3 port valve
MXBC-10
MXBC-15
MXBC-20
MXBC-25
MXGC-15
MXGC-20
MXGC-25
Rc3/8
Rc1/2
Rc3/4
Rc1
Rc1/2
Rc3/4
Rc1
10
10
15
20
10
14
19
10
6
16
29
3
6
11
Application
Candy drying device
3 second operation / 5 second stop
Fully open-fully closed 8
2.0
2.0
2.2
A-C flow path-B-C flow path 16
2.3
2.2
Fan coil unit
Current input signal for open angle control, 4 to 20mA
Hot air blow for drying
Hot water
Conveyer for drying
Hot water pip
Controller
Temperature sensor
Candies
598
2.3
Proportional control motor valve
2.5
MXBC/MXGC Series
How to order
When standard type (current input control circuit board incorporated)
HNB/G
MX B C
15
O
3
USB/G
FAB/G
Series
Descriptions
Symbol
No. of port
B
2 port
G
3 port
FGB/G
Remarks
A
A No. of port
B
B Port size
C
C Body/Seat
D Voltage
D
Port size
Rc3/8
10
Rc1/2
15
Rc3/4
20
Rc1
25
FVB
Multi fluids type
FWB/G
Only MXBC (2 port valve) available
FHB
FLB
AB
Body/Seat
O
Body - bronze/Seat - PTFE
E
Body - stainless steel/Seat - PTFE
AG
Voltage
3
24 VDC
AP/AD
APK/
ADK
For
dry air
Explosion
proof
HVB/
HVL
When simple control type (no control circuit board but potentiometer only)
15
0
N
SAB/
SVB
1
Descriptions
Symbol
A No. of port
B
2 port
G
3 port
Series
A No. of port
B
B Port size
C
Body/Seat
O
Body - bronze/Seat - PTFE
E
Body - stainless steel/Seat - PTFE
D
Option
N
C Body/Seat
D Option
E Voltage
Port size
Rc3/8
10
Rc1/2
15
Rc3/4
20
Rc1
25
E
NP/NAP/
NVP
Remarks
CHB/G
Multi fluids type
MXB/G
Only MXBC (2 port valve) available
Other G.P.
systems
PD/FAD/
PJ
CVE/
CVSE
CPE/
CPD
Medical
analysis
Simple control type
Proportional positioning control device
(no control circuit board but potentiometer only) is required for proportional control.
Voltage
1
100 VAC (50/60Hz)
2
200 VAC (50/60Hz)
<Example of model number>
MXBC-15-0-N-1
Series: MXBC
A No. of port
B Port size
C Body/Seat
D Option
E Voltage
Custom
order
Motor valve proportional control
Electric driven ball valve 2, 3 port valve
MX B C
: 2 port valve
: Rc1/2
: Body - bronze/valve seat - PTFE
: simple control type
: 100 VAC (50/60Hz)
599
MXBC/MXGC Series
Internal structure and main parts material
MXBC-10/15/20/25-0
16
15
1
2
3
14
4
17
5
6
8
7
9
12
10
13
11
MXGC-15/20/25-0
16
15
1
2
3
14
4
17
5
6
8
7
9
13
10
12
11
A
B
C
No. Parts name
1
2
3
4
5
6
7
8
9
Material
Bonnet
ADC12
Aluminum alloy die-casting
Gasket
NBR
Nitrile rubber
Adaptor
ZDC2
Zinc alloy die-casting
Stopper
C2700
Brass
O ring
FKM
Fluoro rubber
Intermediate bush SUS303
FKM, NBR *1 Fluoro rubber/ nitrile rubber
O ring
FKM
Valve ball
C3771 (SUS304) Brass *2 (stainless steel)
( ) shows values for stainless steel body
600
Stainless steel
O ring
Fluoro rubber
No. Parts name
Material
10
11
12
13
14
15
16
17
Ball seat
PTFE
Body
CAC407 (SCS13) Bronze casting (stainless steel casting)
Cap
CAC407 (SCS13) Bronze casting (stainless steel casting)
Hexagon head bolt SWCH
Tetrafluoroethylene resin
Carbon steel wire for cold forging
Code
0.75mm2, 3-conductor -
Bushing
PF
Cross headed pan SWCH
Shaft
Phenol resin
Carbon steel wire for cold forging
SUS303 (SUS304) Stainless steel (stainless steel)
* 1: Upper O ring is NBR, lower is FKM. For stainless steel, FKM is used for both upper and lower O rings.
* 2: Valve ball made of hard chrome plated brass.
MXBC/MXGC Series
(Page 613)
Dimensions
MXBC-10/15/20/25-0
(50)
64
HNB/G
80
54
USB/G
FAB/G
FGB/G
FVB
D
C
FWB/G
FHB
300
FLB
AB
(60)
F
AG
AP/AD
A
B
2-E
APK/
ADK
Cabtire cord length 300 mm
Model
MXBC-10
MXBC-15
MXBC-20
MXBC-25
A
B
50 (56) 24 (28)
C
D
151
E
For
dry air
F
166 (167) Rc3/8
10
56
28
151
166 (167) Rc1/2
10
65
34
157
176.5 (177.5) Rc3/4
15
76
41
160
183 (184)
20
Rc1
Explosion
proof
HVB/
HVL
SAB/
SVB
( ) shows values for stainless steel body
NP/NAP/
NVP
(50)
MXGC-15/20/25-0
64
54
80
CHB/G
MXB/G
Other G.P.
systems
PD/FAD/
PJ
C
CVE/
CVSE
D
CPE/
CPD
300
Medical
analysis
F
A
Motor valve proportional control
Electric driven ball valve 2, 3 port valve
(60)
Custom
order
B
A C
3-E
B
Cabtire cord length 300 mm
Model
A
B
C
D
E
F
MXGC-15
MXGC-20
MXGC-25
56
28
151
181
Rc1/2
10
65
34
157
193
Rc3/4
14
76
41
160
202
Rc1
19
601
driven ball valve 2, 3 port valve miniature type
MHB4/MHG4 SeriesElectric
(motor valve)
MHB4/MHG4 Series
Port size: Rc3/8 to Rc1
Common specifications
MHB4/MHG4
Descriptions
Working fluid
Working pressure range MPa
Withstanding pressure (water) MPa
Fluid temperature
Ambient temperature
%
Ambient humidity
Valve seat leakage cm3/min
Installation attitude
Note 1
Rated voltage
100 VAC
Apparent
200 VAC
power VA
100 VAC
200 VAC
Power consumption W
Cycle rate
Water, hot water, air, oil (500mm2/s or less)
0 to 0.5
1.0
0 to 80 (no freezing)
-10 to 50
70 or less
0 (under 0.5MPa water pressure)
Limited from vertical to horizontal installation placing motor top.
Starting Holding
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
4.4/3.5 (50/60Hz)
3.4/2.6 (50/60Hz)
4.4/3.5 (50/60Hz)
3.4/2.6 (50/60Hz)
5
1 cycle/min. or less
Individual specifications
Descriptions
Port size
Orifice
mm
Cv flow factor
Interval when
50Hz
activated sec. 60Hz
Mass
kg
Pressurization direction
2 port valve
3 port valve
MHB4-10-25 MHB4-15-25 MHB4-20-25 MHG4-10-25 MHG4-15-25 MHG4-20-25
Rc3/8
Rc1/2
Rc3/4
Rc3/8
Rc1/2
8
8
10
8
8
10
3.3
3.0
4.7
1.8
1.1
3.0
0.42
4.5
9
3.8
7.5
0.44
0.51
0.45
Random
Note 1: Allowable voltage range should be within 10% of rated voltage.
Note 2: Consult with CKD about other than above specifications.
Note 3: Only when vertical installation placing motor top, protection grade is JIS CO920 IPX2 "drip proof type ll.
602
0.49
Limited to Port C pressurized
Rc3/4
0.57
MHB4/MHG4 Series
How to order
HNB/G
MH B 4
20
25
AC100V
USB/G
FAB/G
FGB/G
Working pressure
0 to 0.5MPa
Series
Symbol
A
No. of port
B
2 port
G
3 port
B
Port size
10
Rc3/8
15
Rc1/2
20
Rc3/4
A No. of port
B Port size
FVB
Descriptions
FWB/G
FHB
FLB
AB
Voltage
AC100V 100 VAC (50/60Hz)
AC200V 200 VAC (50/60Hz)
C
C Voltage
AG
AP/AD
APK/
ADK
For
dry air
Explosion
proof
<Example of model number>
MHB4-20-25-AC100V
HVB/
HVL
Series: MHB4
SAB/
SVB
NP/NAP/
NVP
: 2 port valve
: Rc3/4
: 100 VAC (50/60Hz)
CHB/G
MXB/G
Other G.P.
systems
PD/FAD/
PJ
CVE/
CVSE
CPE/
CPD
Medical
analysis
Custom
order
Motor valve
Electric driven ball valve 2, 3 port valve
A No. of port
B Port size
C Voltage
603
MHB4/MHG4 Series
Internal structure and main parts material: MHB4 Series
MHB4-10-25
1
2
3
4
5
8
6
9
7
12
11
13
MHB4-15/20-25
1
2
3
4
5
8
6
7
10
11
13
No. Parts name
1
2
3
4
5
6
604
Cover
Material
PP
Polypropylene resin
Motor assembly -
-
Shaft
SUS303
Stainless steel
O ring
FKM
Fluoro rubber
O ring
FKM
Fluoro rubber
Valve ball
CAC407
Bronze casting
No. Parts name
Material
7
8
9
10
11
12
13
Valve seat
PTFE
Tetrafluoroethylene resin
Body
CAC407
Bronze casting
Cap
CAC407
Bronze casting
Insert
CAC407
Bronze casting
Hexagon socket head cap screw SCM435
Alloy steel
O ring
FKM
Fluoro rubber
Cabtire cord
0.3mm2, 5-conductor -
MHB4/MHG4 Series
Internal structure and main parts material: MHG4 Series
MHG4-10-25
HNB/G
USB/G
FAB/G
FGB/G
FVB
FWB/G
1
2
FHB
FLB
AB
3
4
AG
B
11
A
5
AP/AD
6
7
8
C
12
APK/
ADK
13
9
For
dry air
MHG4-15/20-25
Explosion
proof
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
CHB/G
MXB/G
Other G.P.
systems
1
2
PD/FAD/
PJ
CVE/
CVSE
3
CPE/
CPD
10
4
Medical
analysis
11
5
B
A
Custom
order
6
7
Motor valve
Electric driven ball valve 2, 3 port valve
8
13
C
No. Parts name
1
2
3
4
5
6
Cover
Material
PP
Polypropylene resin
Motor assembly -
-
Shaft
SUS303
Stainless steel
O ring
FKM
Fluoro rubber
Valve ball
CAC407
Bronze casting
Valve seat
PTFE
Tetrafluoroethylene resin
No. Parts name
Material
7
8
9
10
11
12
13
O ring
FKM
Fluoro rubber
Body
CAC407
Bronze casting
Cap
CAC407
Bronze casting
Insert
CAC407
Bronze casting
Hexagon socket head cap screw SCM435
Alloy steel
O ring
FKM
Fluoro rubber
Cabtire cord
0.3mm2, 5-conductor -
605
MHB4/MHG4 Series
(Page 613)
Dimensions: MHB4 Series
MHB4-10-25
77
2
(63)
12
8
300
2-Rc3/8
25
24
50
Cabtire cord length 300 mm
MHB4-15/20-25
77
2
(D)
12
E
300
2-F
A
B
C
Cabtire cord length 300 mm
Model
A
B
C
D
E
F
MHB4-15-25
MHB4-20-25
27
27
56
63
8
Rc1/2
30
32
63
66
10
Rc3/4
606
Cautions on use
Since this valve rotates one way only, reverse turn is impossible
during operation. For example, if the operation switch is returned to
closed during switching close to open, the valve will be closed after
fully open.
MHB4/MHG4 Series
(Page 613)
Dimensions: MHG4 Series
MHG4-10-25
HNB/G
USB/G
FAB/G
FGB/G
FVB
77
FWB/G
12
2
FHB
(63)
FLB
AB
AG
300
B
A
25
AP/AD
APK/
ADK
C
25
Cabtire cord length 300 mm
3-Rc3/8
25
24
For
dry air
Explosion
proof
MHG4-15/20-25
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
CHB/G
MXB/G
Other G.P.
systems
77
PD/FAD/
PJ
12
2
CVE/
CVSE
D
CPE/
CPD
Medical
analysis
Custom
order
300
C
C
A
3-F
E
B
Cabtire cord length 300 mm
Model
A
B
C
D
E
F
MHG-4-15-25
MHG-4-20-25
29
27
29
63
27
Rc1/2
33
32
33
66
30
Rc3/4
Cautions on use
Since this valve rotates one way only, reverse turn is impossible
during operation. For example, if the operation switch is returned to
Flow path B-C during switching Flow path B-C to Flow path A-C,
the valve will turn Flow path B-C after completed the change to
Flow path A-C.
607
Motor valve
Electric driven ball valve 2, 3 port valve
A
B
Electric driven ball valve type temperature control system
MHBP Series
MHBP Series
Motor valve and thermostat combination
Port size: Rc1/2 to Rc1
Common specifications
MHBP
Descriptions
Working fluid
Working pressure range MPa
Withstanding pressure MPa
Fluid temperature
Ambient temperature
Ambient humidity
%
Valve seat leakage cm3/min
Rated voltage
Note 1
Power consumption W
Pressurization direction
Installation attitude
Operation time
50Hz
sec. 60Hz
Thermostat specifications
Measuring range
Water, hot water, steam
0 to 0.5
1.75
0 to 150 (no freezing)
-10 to 50
70 or less
0 (under 0.5MPa water pressure)
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
9 or less
Random
Limited from vertical to horizontal installation placing motor top.
13
11
Thermocouple K1: -200 to 1300 K2: 0.0 to 500.0 T: -199.9 to 400.0
Resistance temperature sensor Pt100 ohm -199.9 to 650.0
Indicated accuracy
Thermocouple: (
0.3% of the indicated value or
Resistance temperature sensor: (
Proportional band %FS
Integral time
sec.
Derivative action sec.
Alarm output
Sampling cycle
ms
Rated voltage
Note 1
Power consumption VA
Ambient temperature range
Applicable output
1
, whichever is larger)
0.2% of the indicated value or
0.8
1 digit or less
, whichever is larger)
1 digit or less
0.1 to 999.9
1 to 3999
0 to 3999
Upper and lower limit setting (250 VAC, 3A)
250
100 VAC (50/60Hz) and 200 VAC (50/60Hz)
Approx.15
-10 to 55 (no freezing)
Motor valve MHBP Series
Individual specifications
Descriptions
Port size
Orifice
Cv flow factor
Mass
MHBP-15
MHBP-20
MHBP-25
Rc1/2
Rc3/4
Rc1
10
15
19
6
14
28
2
2.1
2.1
mm
kg
Note 1: Allowable voltage range should be within 10%.
Note 2: Only when vertical installation placing motor top, protection grade is JIS CO920 IPX2 "drip proof type ll.
How to order
MHBP
20
25 C
T
E
AC100V
Symbol
Working pressure
0 to 0.5MPa
A Port size
B Body material
15
20
25
B
Blank
C
Body material: BC6
Body material: SCS13
C
Blank
T
Motor valve only (no thermostat)
Thermostat + motor valve set
D
Blank
E
3-conductor cable (no output)
5-conductor cable (output lead wire)
C Thermostat
<Example of model number>
MHBP-20-25C-T-E-AC100V
D Option
Series: MHBP
A Port size
B Body material
C Thermostat
D Option
E Voltage
608
: Rc3/4
: SCS13
: Thermostat + motor valve set
: 5-conductor cable (output lead wire) E Voltage
: 100 VAC (50/60Hz)
Descriptions
Rc1/2
Rc3/4
Rc1
A
E AC100V 100 VAC (50/60Hz)
AC200V 200 VAC (50/60Hz)
MHBP Series
Names and functions of front section
Precautions for temperature regulator
Measurement value
display section
Manual operating
display
RSP mode
Avoid use in areas with high levels of dust or corrosive
gas.
Avoid use in areas with high levels of vibration or
impact, where the device could be submerged in water
or subject to oil, on in areas with high temperatures.
Install the device as far as possible from devices
generating strong high frequency noise (such as high
frequency welders or high frequency sewing machines,
etc.).
When tightening the terminal screws, take care not to
tighten excessively.
The lead wires connecting the temperature measuring
element and temperature regulator are easily
influenced by noise and induction, so lay these as far
as possible from the power supply line and load line.
When using this device for a sequence circuit, it may
take several seconds for the relay to turn ON when the
power is turned ON. Take care when assembling the
temperature regulator into the sequence circuit.
OMRON E5EK-PRR2B is used.
Setting value
display section
PV
Remote
Auxiliary output 1
(Alarm) Operation display
SV
Open output
operating display
Auxiliary output 2
(Alarm) Operation display
RMT
RSP
MANU
SUB1
OUT1
OUT2
STOP
AT
SUB2
Close output
operating display
AT operating display
Setting key (UP)
Mode key
A
M
Auto/manual output
changeover key
E5EK
Setting key (DOWN)
Operation stop display
HNB/G
USB/G
FAB/G
FGB/G
FVB
FWB/G
FHB
FLB
AB
AG
AP/AD
APK/
ADK
For
dry air
Internal structure and main parts material
Explosion
proof
HVB/
HVL
12
SAB/
SVB
NP/NAP/
NVP
13
4
CHB/G
5
14
1
MXB/G
20
Other G.P.
systems
6
15
9
PD/FAD/
PJ
7
16
17
10
CVE/
CVSE
2
8
3
11
CPE/
CPD
18
19
Medical
analysis
No. Parts name
Material
1
2
3
4
5
6
7
8
9
10
NBR
O ring
Nitrile rubber
Hexagon head bolt SUSXM7
Stainless steel
Cabtire cord
-
-
Geared motor
-
-
Base
A5056
Aluminum
O ring
NBR
Nitrile rubber
Bush
SUS303
Stainless steel
Spring washer
SUS304
Stainless steel
Cap
CAC407
Bronze casting
O ring
FKM
Fluoro rubber
No. Parts name
Material
11
12
13
14
15
16
17
18
19
20
Valve ball
SUS304
Stainless steel
Bonnet
SPC
Steel
Mounting plate A6063
Aluminum
Flat headed cross cut screw SUSXM7
Stainless steel
Shaft
SUS303
Stainless steel
O ring
FKM
Fluoro rubber
Valve seat
Reinforced PTFE -
Body
CAC407
Bronze casting
O ring
FKM
Fluoro rubber
Thermostat
-
-
Motor valve proportional control
Electric driven ball valve 2 port valve
Custom
order
609
MHBP Series
Dimensions
(Page 613)
MHBP-15/20/25
90
48
13.5
100
450
C
B
2-D
A
Cabtire cord length 450 mm
Model
A
B
C
D
MHBP-15-25-T
MHBP-20-25-T
MHBP-25-25-T
65
29
138
Rc1/2
80
35
142
Rc3/4
92
44
145
Rc1
610
91
112
96
55
MHBP Series
External connection diagram
HNB/G
Motor valve
100 / 200 VAC
Thermostat
10
9
8
7
6
5
Red
Cable
M
White
Black
* When thermocouple, connect (11) to +, (12) to -.
USB/G
FAB/G
A
B
13
12
11
*
B Resistance temperature
sensor
When selecting temperature detector, if high precision
required or temperature 100
or less, select Class
0.5 platinum resistance temperature sensor, while
general use, select Class 0.75 thermocouple. When
using thermocouple, compensating lead wire should
be used.
<<Recommendation: OMRON E52 series>>
FGB/G
FVB
FWB/G
FHB
FLB
Cv flow factor and applicable valves
AB
In order to perform highly accurate control, Cv flow factor should be the middle (
) in the control range.
AG
AP/AD
APK/
ADK
MAX
(Fully open)
For
dry air
100 / 200 VAC
Explosion
proof
(Cv flow factor)
Control range
Cv flow factor
Port size
Control range
Cv flow factor
15
20
25
0.2 to 2.5
0.5 to 4
1 to 14
HVB/
HVL
SAB/
SVB
NP/NAP/
NVP
O
(Fully closed)
CHB/G
Drive time
MXB/G
Other G.P.
systems
PD/FAD/
PJ
Temperature control e.g.
CVE/
CVSE
CPE/
CPD
Thermostat
Water
100 or 200 VAC
Medical
analysis
Subject to control
Heat exchanger
Custom
order
Motor valve
Motor valve proportional control
Electric driven ball valve 2 port valve
Pump
P
Temperature
detector
Steam
611