Product Datasheet: ARC CS2
100% Solids, mineral reinforced, wear resistant, low viscosity epoxy.
ARC CS2 thin film industrial coating is designed to:
■■
■■
■■
Protect new & old concrete subject to mild chemical and/or physical damage
Replace tiles, outlast paints and other concrete coatings
Apply by roller, brush, squeegee or airless or heated plural component spray
Application Areas
■■
■■
■■
Concrete tanks
Secondary containment
Water intakes and dams
■■
■■
■■
Sumps, drains & pits
Process floor areas
Wastewater treatment
Features and Benefits
Pump & equipment
bases
■■
■■
Durable high performance
coating
■■
■■
Packaging and Coverage
■■
100% solids; no VOCs; no free
isocyanates
■■
Nominal, based on a 500 µm (20 mil) thickness
■■
16 liter kit covers 32.00 m2 (344.45 ft2)
■■
Note: Components are pre-measured & pre-weighed.
Each kit includes mixing and application instructions.
■■
Technical Data
CompositionMatrix
Reinforcement (Proprietary)
Cured Density
Pull-Off Adhesion
Compressive Strength
Tensile Strength
Tensile Elongation
Flexural Strength
Flexural Modulus
Thermal Compatibility to Concrete
5 cycles/dry/< -10°C to 50°C (<14°F to 122°F)
Hardness Shore D
Vertical Sag Resistance,
at 21°C (70°F) and 150 µ (6 mils)
Maximum Temperature
(Dependent on service)
Shelf life (unopened containers)
Resists delamination and provides
long term protection
Adhesion exceeds cohesive
strength of concrete
A modified epoxy resin reacted with polyamidoamine curing agent
Blend of surface modified mineral reinforcements providing resistance to permeation &
chemical attack
(ASTM D 4541)
(ASTM D 695)
(ASTM D 638)
(ASTM D 638)
(ASTM D 790)
(ASTM D 790)
1.3 gm/cc
>35.1 kg/cm2 (>3.4 MPa)
680 kg/cm2
240 kg/cm2
4.7%
410 kg/cm2
2.5 x 104 kg/cm2
(ASTM C 884 Modified)
Pass
(ASTM D 2240)
87
81 lb/ cu.ft.
>500 psi Concrete Failure
9,650 psi
3,380 psi
5,800 psi
3.5 x 105 psi
No Sag
Wet Service
52°C
125°F
Dry Service
93°C
200°F
2 years [stored between 10°C (50°F) and 32°C (90°F) in dry, covered facility]
A.W. Chesterton Company
860 Salem Street, Groveland, MA 01834 USA
Tel +1 978-469-6888 Toll Free 844-469-6888
[email protected]
© 2016 A.W. Chesterton Company
Registered trademark owned and licensed by A.W.
Chesterton Company in USA and other countries,
unless otherwise noted.
®
Excellent resistance to permeation
Achieves strong adhesion to
concrete
■■
■■
Saves time by allowing application
under a variety of conditions
Surface Modified Mineral
Reinforcements
■■
■■
Enhances safe use
No Shrinkage on cure
Can be applied to dry or damp
concrete
■■
Color: Light gray
Dramatically outlasts conventional
paints and coatings
Technical Data reflect results of laboratory tests and are intended to indicate general characteristics only. Since many actual application circumstances
are beyond Chesterton's knowledge and/or control, the product user must determine the suitability of the products it intends to use for its particular
purpose and assume all risks and liabilities in connection therewith. CHESTERTON DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Form No. 084966
ARC CS2
2016/01/20