Working with Suspended Access Systems

Working with Suspended Access Systems
Selecting the Best Solution for Access Challenges in the Air,
Around Curves, in Tight Corners and Underneath Structures
Executive Summary
Situation
Economic factors have prompted industrial and commercial construction companies
to work with smaller budgets and tighter project time lines; while scaffolding and
access challenges under bridges, inside boilers and separation vessels, offshore, and
in/around buildings have continued to increase. Suspended access solutions can often
be used to effectively address design and structural issues and offer a higher degree
of efficiency, saving both time and money. However, choosing the best solution for a
specific application is not always easy.
Challenge
According to the Occupational Safety and Health Administration (OSHA), there are
eight types of suspended access available. Sometimes a simple, cost-effective system
can provide needed access, but seeking a solution based on cost alone is likely to
backfire. Inexpensive suspended access solutions can be time-consuming to erect,
may provide an unstable working platform, are not usually offered in combination
with other access equipment, such as supported scaffolding and hoists, and ultimately
could compromise safety. In addition, working with a company that provides a
suspended access system, without the necessary experience, engineering, training and
support to safely and optimally utilize the equipment, could be equally disastrous.
Solution
Understanding what types of suspended products are available and the differences
between them is key to selecting the optimum solution for a specific application.
Experience has shown that multi-point access systems with rigid platforms are
consistently outperforming other solutions. In addition, choosing to work with a
comprehensive access solutions company, which has the background, knowledge,
labor, management, equipment and skills to efficiently and safely take projects from
start to finish, is also essential to the successful use of any suspended access products.
©2013 Safway Services, LLC All rights reserved.
Suspended Access
Overview
Eight Types of Suspended Scaffold
Many structures in the commercial
and industrial markets consist of
unique shapes requiring specialty
access solutions. Suspended
scaffolding is a great asset for
difficult-to-reach locations and
elevations; however several
factors need to be considered
before pursuing this route. There
are numerous products to choose
from; not all are suitable for
every application. Suspended
scaffold solutions can also be
dangerous when not used
correctly or without the proper
safety equipment and training.
Suspended Scaffold Type
Two-Point (Swing Stage)
According to the Occupational
Safety and Health Administration
(OSHA), eight types of suspended
access are available: Two-Point
(swing stage), Single-Point
Adjustable, Catenary, MultiPoint Adjustable, Interior Hung,
Needle Beam, Multi-Level, and
Float (ship). Each of these access
solutions has its own OSHA
regulations and guidelines,
which must be followed. Building
suspended scaffolding has the
potential to be time-consuming
and possibly dangerous, if not
done correctly. When reviewing
product information, both ease of
erection and dismantling should
also be taken into consideration.
Needle Beam
©2013 Safway Services, LLC All rights reserved.
Single-Point Adjustable
Catenary
Multi-Point Adjustable
Interior Hung
Multi-Level
Float (Ship)
Product Description and Use
Usually used by window washers, or for high-rise construction, this is the most
common suspended scaffolding. A platform is suspend by ropes or cables
connected to stirrups at each end of the platform.
Window washers and single-worker projects utilize this type of scaffold. This
smaller platform is suspended by using only one rope or cable.
Bridges and offshore rigs are frequent users of this type of scaffold. Catenary
scaffold consists of a platform supported by two horizontal and parallel ropes
attached to structural members of a building or structure.
Chimney hoists, bridges, construction, and other specialty projects use this type
of scaffolding. A platform is supported by multiple suspension points from an
overhead connection. (See diagram below showing multi-point suspended access
solution with rigid platform.)
Used for internal work on structures, this interior-hung scaffold consists of a
platform that is suspended from a roof or ceiling by fixed-length supports.
Steel structures and riveting gangs are two big users of this type of scaffold. Needle
beam suspended scaffold consists of a platform that is suspended from needle
beams and usually attached on one end to a permanent structural member.
Often used by window washers and construction sites, the multi-level suspended
scaffolding consists of either two-point or multi-point adjustable suspended
scaffolding with a series of platforms placed at various levels resting on common
stirrups.
A float, or ship, scaffold is a suspended scaffold used for many types of industries.
This suspended scaffold consists of a braced platform resting on two parallel
bearers and hung from overhead by ropes of fixed length.
To review corresponding OSHA regulations, go to www.osha.gov
2
Suspended Access
Overview - continued
In addition, you will want to compare
suspended access products with
flexible decking versus rigid platforms.
Inexpensive suspended access
solutions providers often utilize lowcost flexible platforms to reduce price.
These platforms are typically made
of galvanized roof deck or chain link
materials. Flexible platforms provide
a surface that can be difficult to work
on and hard to maneuver equipment
across. In addition they can be timeconsuming to erect, do not facilitate
use in multiple applications and are
not usually offered in combination with
other access solutions products, such as
supported scaffolding and/or hoists.
The cost to build ground-supported
scaffold gets more expensive as working
elevations increase because supported
scaffolding is three-dimensional (length,
height and width) while suspended
scaffolding is two-dimensional (length
and width). This means that ground
supported scaffolds require more
material to reach greater elevations,
while suspended scaffolds utilize the
same amount of equipment, regardless
of elevation. When projects require
work to be done at a specified location,
high off the ground, suspended scaffold
provides an efficient, cost-saving solution.
Multi-Point Suspended Access Systems with Rigid Platforms
Multi-point suspended access scaffold
with rigid platforms provides a stable
work surface and has been used to
address multiple access challenges
with a high degree of efficiency. These
modular platforms are designed for
easy installation to save on labor, can
be “built in the air” to save time and
“leapfrogged” to reduce equipment costs.
Leapfrogging is the process of removing
material from one end to be used at the
other. Leapfrogging uses less material
and can increase project profitability.
In addition, by using a cantilevered
system with rigid platforms, erectors
can assemble a product more safely.
When engineered, multi-point suspended
access systems can be designed to withstand
high loads at a 4:1 ratio, span over large areas,
fit unique shapes and be combined with
other access solutions, such as supported
scaffolding. Rigid platforms provide safe
barriers between the area where work is
performed and anything below. Properly
trained, laborers can safely function at
high elevations, allowing multiple trades
to operate side-by-side with a high degree
of efficiency, uninhibited by any restriction
of what may be below the platform. This
valuable access solution can be configured to
meet the needs of many applications in both
the commercial and industrial industries.
3
©2013 Safway Services, LLC All rights reserved.
Commercial Applications
Bridges
Many bridges within the United States are nearing
retirement age with almost one-third of the 600,000
bridges already exceeding their expected lifespan of 50
years. Maintenance is in high demand, while funding
is low. Bridge maintenance usually requires work to
be done underneath the bridge – which is over water,
roads, railroads or other non-ground accessible areas.
Occasionally, though, work needs to be performed
above traffic (on archway bridges) without disrupting
traffic flow. Due to the nature of the locations where
the work is to be performed, the potential for high
costs and large project time lines is significant.
Suspended access solutions are the preferred system
used to perform maintenance and repair on these
difficult-to-reach areas on bridges. One frequently
used suspended access solution on bridge projects has
been catenary systems. Catenary suspended scaffolds
are commonly built by attaching cables horizontally
to bridge anchors, and vertically from under the deck
of the bridge. Once the cables have been placed,
platforms that are built out of galvanized roof deck
or chain link materials are laid across the working
surface area. The platforms of these catenary systems
are flexible, creating a work surface that constantly
bows when stepped upon. Without rigid surfaces to
walk on, work is slowed because labor and materials
cannot easily move across the surface of the system.
Multi-point suspended access systems with rigid
platforms have been consistently out-performing
catenary systems on bridge projects. Advantages
include easier and safer installation and dismantle,
as well as a reliable, level work surface. In addition,
these systems can be engineered to closely fit
the curves of virtually any bridge design.
©2013 Safway Services, LLC All rights reserved.
I-430 Bridge Project
Two side-by-side bridges connect Little Rock with North Little Rock across the Arkansas River.
Sections of concrete piping each 40 feet long and weighing almost 7,000 pounds, needed to be
installed under the bridge to serve as water lines. In the past, to complete such an enormous
task, contractors would use cranes and barges. This meant that the pipe was hoisted by crane
from a barge, installed by work crews, and then finally inspected, one section at a time.
When presented with this challenge, Safway Services, the access company for the project, engineered a
multi-point suspended access solution with a rigid platform to provide a flat “factory floor” surface that
enabled workers to hoist and install the pipeline, while inspectors followed closely behind. The pipeline
no longer needed to be added section by section with a crane and barge. Using a suspended access
solution with a rigid platform sped up productivity by more than 35 percent creating significant savings.
4
Specialty Commercial Structures:
Atriums, Domes, Aquatic Centers,
Airports and More
Specialty commercial structures often
require a customized approach. Usually
heavily trafficked, these facilities can
prove to be costly to maintain and repair
– especially when the structure’s main
use is interrupted in the process. If the
maintenance work or repair requires
supported scaffolding to be erected to reach
high elevations within a structure, erection
and disassembly of the scaffold can prove
to be disruptive to regular activities at the
location. Multi-point suspended scaffolding
with rigid platforms can offer a safe and
effective means of providing work surfaces
for repairs well above any regular activities,
without the interruption of a structure’s use.
Catenary suspended scaffolds cannot
be easily adjusted or configured to fit
commercial structures other than bridges
due in large part to the installation
techniques. Installing catenary scaffolding
on commercial projects would be next
to impossible without tying into the
structure horizontally. In addition, the
flexible platforms, such as chain-link
material, would not be an effective
barrier to keep pedestrians and others
below the work surface safe. They also
do not lend themselves to material
movement or support the use of
traditional scaffold on top of the deck.
Madison Square Garden Renovation
Madison Square Garden, which takes up most of two city blocks in the heart of Manhattan in New York City,
is host to numerous top-name events. Due for extensive renovations and upgrades, this unique structure
required a customized approach to access. While some areas were able to tolerate a supported scaffold
structure, often crews needed to work at elevated levels within the structure, while not disturbing the flow
of business on lower levels. In addition, the floor of the arena had to be protected. The access company
for the job engineered a combination of supported and suspended scaffolds together with several unique
custom solutions to enable all work to be performed with a high degree of efficiency.
A key challenge on the project was creating access on top of Penn Station, which is situated underneath
Madison Square Garden and serves as a major New York City transportation hub. Workers needed to access
areas of the arena above, while not disrupting the busy Amtrak station below. A suspended access system
provided the perfect solution. A 15,000-square-foot platform was put in place and in use for over a year. Due
to this innovative use of a suspended access system, the Amtrak station was able to operate safely without
any interruptions, while construction and renovation work was performed above.
5
©2013 Safway Services, LLC All rights reserved.
Zinc Roaster Dome Access Challenge
When Nyrstar, a leading global multi-metals company, needed
access to a 43-foot-wide by 71-foot-tall zinc smelting roaster dome,
in Clarksville, Tenn., their primary concern was worker safety. To
make the necessary renovations on the roaster dome, which was
expected to add another 30 years to the lifespan of the roaster, the
refractory brick that lines the dome had to be replaced. After 33
years of enduring temperatures as high as 1,700 degrees Fahrenheit,
Nyrstar safety officials didn’t want workers directly under the
65-pound bricks during renovation, for fear they could collapse.
Knowing this at the start of the project, the access company for
the project used a modular platform access system. This allowed
all work to be performed from above instead of below the dome.
The access solution involved cutting a hole into the top of the
structure, and then lowering a small,
circular starter platform. From this
platform, the bricks around the leading
edge were removed. As the bricks
were cleared away, making the space
larger, the platform was expanded to
provide additional access. In total, the
platform grew to 40 feet in diameter.
University of Virginia
Aquatic Center
Built over 15 years ago, the University of Virginia
Aquatic Center is home to an Olympic-sized pool –
approximately 50 meters by 25 yards. Access to the
entire ceiling was required when the air handling
system needed repairs. Safway Services, the access
company hired by the contractor, installed a work
platform utilizing 22,000 square feet of QuikDeck®,
a suspended access system, and 8,000 square
feet of Systems™ Scaffold. This allowed multiple
tradespeople to operate side-by-side and access
the ceiling, without needing to drain the pool,
which would have been necessary if a traditional
scaffold structure was used for access.
©2013 Safway Services, LLC All rights reserved.
6
Industrial Applications
Power Generation Facilities
Power generation facilities – coal dust
combustion boilers, nuclear power plants,
hydroelectric dams and thermal stations –
include an array of unique structures that
demand regular maintenance, repair and
updating. These projects, which can range
from a concentrated job in a targeted area to
a full shutdown and turnaround, are usually
performed under strict deadlines, with tight
budgets and require a workforce that has
industry-specific knowledge and experience.
In addition, the Department of Energy (DOE),
the Environmental Protection Agency (EPA),
OSHA, and the Federal Trade Commission (FTC),
all oversee policy and regulation for power
generation facilities and have guidelines that
must be followed.
Coal dust combustion boilers are prime
examples. These boilers contain numerous large
tubes that carry thousands of pounds of water,
that when heated turns into steam. Over time
the tubes erode and need repair, and the shape
of these boiler structures and spaces often
require unique access solutions. Many times
supported scaffolding is built up inside the
boiler. Increasingly, however, suspended access
solutions have been safely used to reduce
downtime and cost. This is especially true when
work only needs to be performed at the upper
levels of the boiler.
Boiler Access Solution Cuts Budget by Half
By utilizing a suspended access solution inside the boiler of a 650-megawatt unit in the Ohio
Valley, significant time and money were saved. By creating a platform inside the boiler 180 feet
in the air, which was suspended from chains and supported by existing steel beams, instead of
using a supported scaffold solution, the total budget for the job was cut in half and the overall
timetable was reduced.
7
©2013 Safway Services, LLC All rights reserved.
Off Shore Rigs and Ships
Stringent safety guidelines in the maritime
industry make the need for regular maintenance
a given. OSHA, the US Coast Guard, the Bureau
of Ocean Energy Management (BOEM), the EPA,
and International Safety Management (ISM),
are just some of the governing bodies that
designate codes and regulations that offshore
rigs and ships need to take into consideration.
Often maintenance on these rigs and ships
require that workers perform repairs beneath
the level of the deck on the outside of these
structures under tight deadlines. In these
instances, suspended access systems have
proven to be an ideal solution.
Offshore Rig Access Saves Critical Time
A contractor based out of Canada needed an access solution that would allow workers to
perform maintenance and repair on an offshore oil rig. Using multiple products, including a
suspended access system, along with more traditional scaffold and high-capacity personnel
hoists, a solution was engineered that reduced the installation time by half. A barge was used
to float a starter platform out to the offshore rig. Once the starter platform was in place, rig
winches were used to lift the platform into the air. Once there, workers were able to build the
rest of the suspended platform in the air.
8
©2013 Safway Services, LLC All rights reserved.
Petroleum Facilities
The oil refining industry continues to face tough challenges.
Many refineries are forced to run at high volumes with as
little downtime as possible. Maintenance is sometimes
delayed to meet increased demand. Due to these
circumstances, it is critical that any maintenance or repair
work – especially if a shutdown or turnaround is required
– be executed in a safe and highly efficient manner. With
the use of suspended access solutions, some petroleum
refinery companies have saved time and rental or
purchasing fees, ultimately reducing costly shut-down time.
Saving Time and Money on Primary Separation Vessel Maintenance
Primary separation vessels are large funnel-shaped vessels about 100 feet in diameter that extract oil from
sand. A primary separation vessel produces approximately 90,000 barrels of oil per day, so when scheduled
maintenance makes a shutdown necessary, oil company managers need highly efficient solutions.
During a recent shutdown at a refinery in Alberta, Canada, a suspended access system proved to be an
ideal solution. The product’s unique ability to be engineered to fit any shape allowed the suspended
scaffold to efficiently fit inside the round vessel. The customer’s turnaround time for the maintenance
project was lowered from 16 days to five, saving the customer no less than $96 million.
9
©2013 Safway Services, LLC All rights reserved.
Finding the Right Access Partner
Access and scaffold providers that not only
supply a complete line of complimentary
products but also have broad experience,
as well as the knowledge and skills unique
to an industry, are essential to maximizing
the efficient use of any suspended access
system. Every project within the industrial and
commercial markets is unique. Using an access
provider that can offer custom solutions, take
a project from the planning stages through
execution, management and wrap-up, and at
the same time provide comprehensive safety
and training, is often the key difference in
increasing productivity and profit margins.
When considering a suspended access solution,
you also will want to look at the provider to
see what kinds of support service they offer
and how they perform in the following areas:
Safety
Safety is one of the most important
considerations when doing work that requires
rigging and suspension. According to OSHA,
fall protection has received the highest
amount of citations in the industrial and
commercial markets (OSHA 1926.501).
In fact, as you can see in the chart below,
fall protection citations were listed as one of
the top three cited violations over a threeyear period. In 2011, 6,274 inspections
were performed by OSHA, and 7,275
citations were given. Often a single job site
was issued more than one citation.
In light of numbers like this, it is important
to think about how new construction and
maintenance can be performed with multipoint suspended scaffolds as safely as
possible. With tight budgets already in place,
no company can afford to pay the fines for
having unsafe practices or work environments.
To reduce the chances of being fined, safety
must be emphasized and training must be
sought. It is imperative that key decisionmakers in the construction industry look at
their access company’s track record in safety,
as well as the guidelines they have in place
to support safe practices and job sites.
Training
Training is invaluable to increase efficiency and
ensure safety. Providing product training allows
equipment users to perform their jobs quickly,
safely and with the best possible results. Be
sure to ask any potential access company
about the various training options available
to accommodate your specific project needs.
Engineering and Planning
In many instances, when working with
suspended access products, engineering
and design are critical to saving time and
money, while increasing safety and overall
efficiency. Before you partner with an access
company on any project, consider the size
and depth of their engineering support.
Seek an access solutions
Fall Protection
partner that has a solid staff
2009
2010
2011
2009 to 2011
of licensed civil, structural
Years
(Oct-Sep)
Comparison
and mechanical engineers,
# Inspections
7,358
7,584
6,724
8% 
as well as state-of-the-art
# Violations
7,139
8,010
7,725
2%
Computer-Aided Design
Penalty Amount $9,816,313 $16,156,231 $23,612,158
140%
(CAD) and structural analysis


©2013 Safway Services, LLC All rights reserved.
software for optimum performance. Then be
sure to allow sufficient time to plan ahead.
Rental, Sales and Inventory
Needs vary from company to company and
project to project. Some require only occasional
access, while others may need it on a regular
basis. Turnkey solution providers that seek to
accommodate individual organizational needs
provide a multitude of products for rent and/
or purchase. In addition, consider product
availability through branch locations and
regional distribution centers with the capability
to efficiently schedule delivery of equipment
with minimal transportation costs and time.
Project Tracking Systems and Accountability
By providing comprehensive data about
your project from start to finish, an access
solution provider can offer real-time
information about equipment, inspections,
labor and productivity for increased cost
transparency. Good project tracking systems
allow managers to monitor and capture data
about every aspect of any job. This includes:
•
•
•
•
•
•
•
•
On-site scaffold and equipment productivity
Types of equipment utilized
How the equipment is being used
Inspections
Cubic foot rate
Dismantling status
Total labor hours/employees’ daily time
Historical data for future reference
Having access to this data increases efficiency,
eliminates non-productive time, decreases
the need for modifications and inventory,
and helps minimize your project costs.
10
Choosing the Best Suspended
Access System for Your Project
Performing on tight budgets has forced
many companies to search for access
and scaffold providers that produce safe,
effective, creative and low-cost solutions.
Through the innovative use of suspended
access systems, numerous companies
have been saving significant time and
money on projects, while also enhancing
safety. Key factors to be considered in
using suspended scaffolds are product
compatibility, training, ease of installation
and dismantling, safety and pricing. In
addition, to get the most out of any
suspended access system, you will want
to work with a scaffolding company that
is able to provide innovative, turnkey
solutions to resolve project challenges
along with a full line of complementary
products, a strong record in safety,
excellent training, engineering support,
project-tracking and accountability.
Multi-point suspended scaffolding access
solutions with rigid platforms provided
by turnkey access solutions providers
safeguard personnel and the public, as well
as a company’s profit margin.
Jerry Dolly is the manager of the Bridge Division at Safway Services, which provides QuikDeck®,
a suspended access solution, for use in commercial and industrial applications. Founded in 1936,
Safway Services is headquartered in Waukesha, Wis. Through its network of approximately 85
branch locations in the U.S. and Canada and a system of distributors across South America,
Safway provides scaffolding and access solutions for commercial construction, industrial and
infrastructure applications. As an industry leader, Safway provides sales, rental, labor services,
training, engineering, design, safety and project management. With an extensive inventory and
a full line of access products, Safway experts design and implement safe, economical access
solutions for projects of any size and scope. For additional information, visit www.safway.com.
11
©2013 Safway Services, LLC All rights reserved.
QuikDeck® Suspended
Access System
• QuikDeck® is multi-point suspended scaffold with a solid
working platform, enabling employees to work effectively
without being hindered by a flexible platform.
• QuikDeck’s® unique design allows it to be assembled from a few
basic components and configured to fit almost any shape or size.
• When purchased, the QuikDeck® suspended access
system provides better long-term ROI. QuikDeck® is
composed of galvanized metal making its components'
lifespan five times longer than its competitors.
• Engineering design and assistance is readily available at low cost.
• QuikDeck® can also be combined with other scaffolding access
solutions. This provides the opportunity to approach difficult
access situations with dynamic and creative solutions.
• QuikDeck® is designed to meet OSHA required weight
bearing ratios of 4:1 and can be configured to up to 150
pounds per cubic foot for uniform live load ratings.
QuickDeck® System Capacities
Platform Self Weight Multi-Point Suspended Scaffold Applications
"Dead-Load"
(Man-Riding)
Maximum Rated Capacities
7lb/ft2 (35Kg/m2)
Protective Shield Applications
(Non-Man-Riding)
Maximum Capacities
Suspender
Grid Nominal
Configurations
16 ft (4.88m)
X
16 ft (4.88m)
8 ft (2.44m)
X
16 ft (4.88m)
8 ft (2.44m)
X
8 ft (2.44m)
8 ft (2.44m)
X
16 ft (4.88m)*
8 ft (2.44m)
X
16 ft (4.88m)
8 ft (2.44m)
X
8 ft (2.44m)*
Uniform Live
Load Rating
25 lb/ft2
(122 Kg/m2)
50 lb/ft2
(244 Kg/m2)
75 lb/ft2
(366 Kg/m2)
100 lb/ft2
(488 Kg/m2)
125 lb/ft2
(610 Kg/m2)
150 lb/ft2
(732 Kg/m2)
*Chain is two-parted in this configuration
Safway Services, LLC
Scotia - Glenville Industrial Park, Bld. 406
Toll free: (800) 582-9391 Telephone: (518) 381-6000
©2013 Safway Services, LLC All rights reserved. ORN 1880 2/13
• Safway’s QuikDeck® suspended access division also
has a diversified workforce with in-depth knowledge
of the product line, all safety regulations that apply to
suspended scaffolding, and extensive knowledge of
different market segments and their access needs.
• Safway also provides international access
through 90 plus locations. This allows Safway
to provide quality labor, products and services
at any time and from anywhere.
• Safway’s QuikDeck® suspended access system saves
valuable dollars through an innovative, patented,
cantilevered erection technique, allowing the
suspended access system to be "built in the air."
• QuikDeck® can also be “leapfrogged” to allow crews to
complete jobs in sections and reduce equipment costs.
• With 5,000 square feet of QuikDeck® platform per
flatbed truck, shipping costs are greatly reduced.
12